| 意味 | 例文 |
primary- sideの部分一致の例文一覧と使い方
該当件数 : 2669件
Matching with an electrodeless field discharge lamp is established by adjusting the number of turns in the secondary winding of a matching transformer, and transistors Q1 and Q2 are installed in the primary side circuit of the matching transformer and allowed to operate as a Class D operation oscillator circuit for current switching, and thereby the conversion efficiency from DC power into high-frequency (radio frequency) power is heightened.例文帳に追加
無電極電界放電ランプとのマッチングを、マッチング・トランスの二次側の巻数を調整することにより、マッチング・トランスの一次側回路にトランジスターQ1,Q2を設置し、それらトランジスターを電流スイッチングのD級動作発振回路として、動作させることにより、直流電力から高周波(無線周波)電力への変換効率が高くなるように構成してある。 - 特許庁
In carrying out the composting treatment to proceed full maturity composting, the primary fermentation and the secondary fermentation of livestock excrements, and animal and plant debris combined at a predetermined mixing ratio are continuously performed using the secondary material containing wooden chips manufactured by processing a thinning material, a pruned tree, wooden building scraps into the size of 8-12 mm in diameter or side and 10-50 mm in length.例文帳に追加
完熟堆肥化を進める堆肥化処理方法を行う際に、所定混合比で混合した家畜排せつ物と動植物性残渣とを、間伐材、剪定樹木、木造建物廃材を、直径あるいは1辺が8〜12mm、長さが10〜50mmに加工して製造された木質チップを含む副資材を用いた1次発酵及び2次発酵を連続して行う。 - 特許庁
The capacitor 46 is added to the secondary side of the transformer 41 by turning on the switch 45 with the breaker 44 closed, so that the voltage drop of the primary side of the transformer 44 is increased so as to lower the source voltage supplying a load 30.例文帳に追加
電力系統に一次巻線41aを接続可能な降圧用のトランス41と、負担抵抗42と、一端が二次巻線41aの一端に接続された遮断器44と、コンデンサ46とスイッチ45との直列回路と、トランス41の二次側電圧を検出して遮断器44及びスイッチ45の開閉制御を行う制御装置47とを備え、遮断器44を閉じた状態でスイッチ45をオンさせてトランス41の二次側にコンデンサ46を投入し、トランス44の一次側の電圧降下を増加させて負荷30に供給する電源電圧を低下させる。 - 特許庁
The ink jet recording material comprises an ink acceptive layer containing inorganic fine particles having primary particles of a particle size of 3 to 30 nm and provided on one side surface of a water resistant support and a back coating layer containing an organic polymer and provided on an opposite side surface of the support.例文帳に追加
耐水性支持体の片面に一次粒子の平均粒径が3〜30nmの無機微粒子を含有するインク受容層を設け、反対面に有機ポリマーを含有する裏塗り層を設けたインクジェット用記録材料において、該耐水性支持体の裏塗り層を設ける面のJIS−B−0601で規定されるカットオフ値0.8mmでの中心線平均粗さRaをA(μm)、該裏塗り層の有機ポリマーの密度をB(g/cm^3)、有機ポリマーの固形塗設量をC(g/m^2)とすると、Aが1〜5μmであり、A、B及びCが下記の式(1)を満足することを特徴とするインクジェット用記録材料。 - 特許庁
In a DC voltage part connecting two or more capacitors in series, and in the switching power supply circuit receiving supply of DC power from the DC power part to switching-control a primary side of a transformer by PWM control so as to output DC voltage of different voltage specifications, the starting resistor of a PWM control circuit is connected to a connection point of the capacitor.例文帳に追加
コンデンサが2個以上直列に接続された直流電圧部と、該直流電圧部から直流電力の供給を受けてトランスの一次側をPWM制御によりスイッチング制御し、電圧仕様の異なる直流電圧を出力するスイッチング電源回路において、PWM制御回路の起動用抵抗器を前記コンデンサの接続点に接続したことを特徴とするスイッチング電源回路。 - 特許庁
This antistatic polyester film comprising a polyester film and a coating layer disposed on at least one side of the polyester film is characterized in that the coating layer comprises 10 to 95 wt.% of an acrylic resin containing 0.1 to 25 mol% of 2-hydroxyethyl methacrylate component as a copolymerization component and 5 to 90 wt.% of tin oxide particles having an average primary particle diameter of 0.5 to 150 nm.例文帳に追加
ポリエステルフィルムおよびその少なくとも片面に設けられた塗布層からなる帯電防止性ポリエステルフィルムであって、塗布層が2−ヒドロキシエチルメタクリレート成分を共重合成分として0.1〜25モル%含むアクリル樹脂10〜95重量%、および平均一次粒子径0.5〜150nmの酸化スズ粒子5〜90重量%からなることを特徴とする帯電防止性ポリエステルフィルム。 - 特許庁
In the sheet-like ink jet recording material having at least one ink accepting layer on a water resistant support, an ink accepting layer includes inorganic fine particles having an average primary particle diameter of 30 nm or less and a hydrophilic binder and the longer side of the sheet-like ink jet recording material is cut at right angle to the flow at the coating of the ink accepting layer.例文帳に追加
耐水性支持体上に少なくとも1層のインク受容層を有するシート状インクジェット記録材料において、インク受容層が平均一次粒径が30nm以下の無機微粒子及び親水性バインダーを含有し、且つ前記シート状インクジェット記録材料の長辺方向がインク受容層塗設時の流れ方向と直角になるように断裁されてなることを特徴とするシート状インクジェット記録材料。 - 特許庁
To provide a manufacturing method of a gas component and a condensable component with a high recovering rate while assuring a predetermined product gas with predetermined purity and a condensable component, and avoiding the liquefaction of the condensable component in a primary side gas of a gas separation membrane in recovering a gas component and a condensable component from the raw material gas containing a plurality of components, and to provide a manufacturing system thereof.例文帳に追加
複数の成分を含む原料ガスからガス成分および凝縮性成分を回収するに際し、所望の純度を有し所望の製品ガスおよび凝縮性成分を確保するとともに、ガス分離膜の1次側ガス中で凝縮性成分が液化することを回避しつつ、高い回収率を得ることができるガス成分および凝縮性成分の製造方法および製造システムを提供すること。 - 特許庁
To provide a method for producing high-purity chitosan oxide provided with high hydrophilicity and water solubility in a wide pH range and a method for further efficiently producing chitosan oxide containing a uronic acid residue in which a primary hydroxy group of the residue of glucosamine or N- acetylglucosamine being a constitutent mucosaccharide of chitosan is selectively oxidized by using a safe reagent under a mild condition with controlling a side reaction.例文帳に追加
高い親水性や幅広いpH領域での水溶性が付与された高純度の酸化キトサンを得るための製造方法、キトサンの構成単糖であるグルコサミンまたはN−アセチルグルコサミン残基の1級水酸基が選択的に酸化されたウロン酸残基を有する酸化キトサンを、安全な試薬を用いて、温和な反応条件下で、副反応を抑えて、より効率よく製造する方法を提供する。 - 特許庁
A switching output voltage, obtained at a primary side resonance circuit, is fed back by an electrostatic coupling system or magnetic coupling system to a power factor improving circuit provided in a power supply circuit called 'push-pull type switching frequency control system composite resonance type converter', and push-pull operation and single end operation are changed over, depending on the AC input voltage with the switching operation change- over means.例文帳に追加
プッシュプル形のスイッチング周波数制御方式複合共振形コンバータといわれる電源回路に備えられる力率改善回路に対して、一次側共振回路に得られるスイッチング出力電圧が静電結合方式もしくは磁気結合方式により帰還するとともに、スイッチング動作切換手段により交流入力電圧に応じてプッシュプル動作とシングルエンド動作を切り換えるようにする。 - 特許庁
An intermittent current is supplied to the primary side of a transformer 207 for preventing unneeded power from being consumed at all times, when a power supply device is composed as an auxiliary power supply for driving a device that needs to be operated even when the electrical equipment body is in standby, and at a standby mode when the auxiliary power supply and the main power supply of the electrical equipment body are shared, respectively.例文帳に追加
電源装置が電気機器本体が待機中でも稼動する必要がある装置を駆動させるための補助電源として構成されている場合は常時、また、この補助電源と電気機器本体の主電源とが共用されている場合は、本体が待機モードにある時に、トランスの1次側への間欠的に電流を供給するようにして、不要な電力を消費しないように構成した。 - 特許庁
The DC-DC convertor 15A is a switching regulator comprising a main winding P inputting a first DC power source and a control winding B for switching the main winding P, at a primary side of a transformer 22, and the control winding B is used in common as one or both of a control power source for motor driver and a driving power source of the protective circuit.例文帳に追加
そして、DC−DCコンバータ15Aは、変圧器22の1次側に、第1直流電源を入力する主巻線Pと、主巻線Pのスイッチングを行うための制御用巻線Bとを備えたスイッチングレギュレータであり、前記制御用巻線Bを、モータ駆動ドライバの制御電源、および、保護回路の駆動電源の一方または双方として共用することを特徴とするミシンの制御装置。 - 特許庁
In a DC voltage part connecting two or more capacitors in series, and in the switching power circuit receiving supply of DC power from the DC power part to switching-control a primary side of a transformer by PWM control so as to output DC voltage of different voltage specification, the switching power circuit is characterized by connecting the starting resistor of a PWM control circuit to a connection point of the capacitor.例文帳に追加
コンデンサが2個以上直列に接続された直流電圧部と、該直流電圧部から直流電力の供給を受けてトランスの一次側をPWM制御によりスイッチング制御し、電圧仕様の異なる直流電圧を出力するスイッチング電源回路において、PWM制御回路の起動用抵抗器を前記コンデンサの接続点に接続したことを特徴とするスイッチング電源回路。 - 特許庁
In the high-voltage output device, a resonance capacitor to form a first resonance circuit with the primary side coil is provided and the input voltage is amplified by the first resonance circuit in a prescribed frequency band.例文帳に追加
1次側コイルに入力された電圧を増幅して2次側コイルから出力するトランスを備え、該1次側コイルに交流の入力電圧が入力されるとともに、該2次側コイルから出力電圧が取り出される、高電圧出力装置において、前記1次側コイルと第1共振回路を形成する共振用コンデンサを備え、前記入力電圧は、該第1共振回路により、所定周波数帯において増幅される高電圧出力装置とする。 - 特許庁
Provided are a rectifier circuit 9 converting an AC voltage transformed from a secondary side of a transformer 8 into a DC rectified voltage, and a filter circuit 10 smoothing the rectified voltage and supplying a prescribed output voltage to a prescribed load circuit 13, and an insertion reactor 21 is made to be inserted in series in the primary winding 81 of the transformer 8 by detecting that the output current to the load circuit 13 becomes a prescribed current value or less.例文帳に追加
トランス8の2次側から変圧された交流電圧を直流の整流電圧に変換する整流回路9、整流電圧を平滑化して所定の出力電圧を所定の負荷回路13に供給するフィルタ回路10を備え、負荷回路13への出力電流が所定の電流値以下になったことを検出して、トランス8の1次巻線81に直列に挿入リアクトル21を挿入する。 - 特許庁
After starting boosting by a step-up transformer 61 by outputting a clock signal FCT1 from an MPU 50 and making an N channel MOSFET 62 perform switching operation, a clock signal FCT 2 is effectively transmitted to the MOSFET 62 or is disabled according to whether or not an AC detection circuit 67 detects that the AC component of the voltage on the primary side of the transformer 61 exists.例文帳に追加
MPU50からクロック信号FCT1を出力してNチャネルMOSFET62をスイッチング動作させて昇圧用トランス61による昇圧が開始された後において、交流検知回路67により昇圧用トランス61の一次側の電圧の交流成分が存在する旨検出されたか否かに応じて、それぞれNチャネルMOSFET62にクロック信号FCT2を有効に伝達させ、あるいは無能化する。 - 特許庁
The power supply circuit for the LED 10 is structured of a rectifying circuit 18 rectifying an alternating-current voltage Vi output from an electronic transformer 14, a constant-current circuit 20 supplying constant current to the LED 16 with supply of direct-current voltage Vdc output from the rectifying circuit 18, and a startup circuit 22 equipped with a resistor 42 connected in parallel with the rectifying circuit 18 at a primary side of the rectifying circuit 18.例文帳に追加
LED用電源回路10を、電子トランス14から出力された交流電圧Viを整流する整流回路18と、整流回路18から出力された直流電圧Vdcを受けて、LED16に対して定電流を供給する定電流回路20と、整流回路18の一次側において、整流回路18に並列接続された抵抗42を有する起動回路22とで構成することにより、上記課題を解決することができる。 - 特許庁
In the cleaning process with a chemical in which a chemical stored in a chemical storage tank is circulated between the chemical storage tank and a separation membrane module with a chemical cleaning pump, while passed from the secondary to the primary side of the membrane constituting the module, the chemical is filtrated with a filter arranged in a pipe connecting the chemical tank with the separation membrane module and then supplied to the module.例文帳に追加
薬液貯槽に貯留した薬液を、薬洗ポンプによって薬液貯槽と分離膜モジュールとの間を循環させる薬洗工程中に、薬液を前記分離膜モジュールを構成する膜の二次側から膜の一次側に向かって通液させる工程において、前記薬液貯槽と前記分離膜モジュールを結ぶ配管の途中に設置したフィルタで薬液をろ過した後、薬液を前記分離膜モジュールに供給することを特徴とする分離膜モジュールの洗浄方法。 - 特許庁
Further, a voltage stabilization circuit 23 for stabilizing the primary side voltage is provided at a front stage of the pumping circuit 22.例文帳に追加
直流電源をエネルギー源として使用するマイナスイオン発生装置について、昇圧のためのメイントランス21を有し、その1次側コイルにポンピング回路22を接続し、2次側コイルには、ポンピング回路22の通電により発生した高電圧をさらに昇圧する逓倍回路24を接続するとともに、逓倍回路24にて昇圧した高電圧を出力するマイナスイオン電極26を接続し、またメイントランス21の2次側コイルにアース線25を接続した構成を有するものとし、また前記のポンピング回路22の前段に、1次側電圧の安定化のための電圧安定化回路23を設けるものとする。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|