性能検査基準の英語

読み取り部１４の性能検査を行うために、レーザダイオード４４から照射される励起光Ｌを反射させてＣＣＤラインセンサ４０に入射させる白基準反射板７０を備える。例文帳に追加

The image-forming apparatus has a white reference reflection board 70 for reflecting excitation light L that is irradiated from a laser diode 44, and is made incident on a CCD line sensor 40 for inspecting the performance of the reading section 14. - 特許庁

干渉計装置３は、基準レンズ３７により光源１から射出される光から、測定光及び参照光を生成し、投影光学系ＰＬを介した測定光と参照光とを干渉させて投影光学系ＰＬの光学性能を検査する。例文帳に追加

An interferometer device 3 produces measuring light and reference light from light emitted from a light source 1 by a reference lens 37, puts the measuring light produced through a projection optical system PL (photo luminescence) into inerference with the reference light, and inspects the optical performance of the projection optical system PL. - 特許庁

五　第五十三条の二（第五十三条の三から第五十四条の二まで及び第七十七条第三項において準用する場合を含む。）の規定により都道府県労働局長、労働基準監督署長若しくは厚生労働大臣が製造時等検査、性能検査、個別検定、型式検定若しくは技能講習の業務の全部若しくは一部を自ら行うものとするとき、又は都道府県労働局長、労働基準監督署長若しくは厚生労働大臣が自ら行つていた製造時等検査、性能検査、個別検定、型式検定若しくは技能講習の業務の全部若しくは一部を行わないものとするとき。例文帳に追加

(v) Where the Director of the Prefectural Labor Bureau, the Chief of the Labor Standards Office, or the Minister of Health, Labour and Welfare decides to carry out the whole or a part of the service of the manufacturing inspection, etc., the performance inspection, the individual examination or the type examination, or the skill training under the provision of 53-2 (including the case where the same provisions are applied mutatis mutandis in Article 53-3 through Article 54-2 and paragraph (3) of Article 77), or where the Director of the Prefectural Labor Bureau, the Chief of the Labor Standards Office, or the Minister of Health, Labour and Welfare decides not to carry out the whole or part of the service of the manufacturing inspection, etc., the performance inspection, the individual examination or the type examination, or the skill training, previously executed by himself/herself.発音を聞く  - 日本法令外国語訳データベースシステム

第四十九条　検定証印等、第七十四条第二項若しくは第三項の合番号又は第七十五条第二項の装置検査証印が付されている特定計量器の改造（第二条第五項の経済産業省令で定める改造に限る。次項において同じ。）又は修理をした者は、これらの検定証印等、合番号又は装置検査証印を除去しなければならない。ただし、届出製造事業者若しくは届出修理事業者が当該特定計量器について、又は第百二十七条第一項の指定を受けた者がその指定に係る事業所において使用する特定計量器について、経済産業省令で定める修理をした場合において、その修理をした特定計量器の性能が経済産業省令で定める技術上の基準に適合し、かつ、その器差が経済産業省令で定める使用公差を超えないときは、この限りでない。例文帳に追加

Article 49 (1) Any person who has performed a alteration (limited to the kind of alterations specified by the Ordinance of the Ministry of Economy, Trade and Industry set forth in Article 2, paragraph 5; the same shall apply in the next paragraph.) or a repair of a specified measuring instrument affixed with a verification mark, etc. matching number set forth in Article 74, paragraph 2 or 3, or fitting inspection mark set forth in Article 75, paragraph 2 shall remove such a verification mark, etc., matching number or fitting inspection mark; provided, however, that this shall not apply to the case where a notifying manufacturing business operator or notifying repair business operator has performed a repair of said specified measuring instrument, or where a person who has obtained a designation set forth in Article 127, paragraph 1 has performed a repair specified by the Ordinance of the Ministry of Economy, Trade and Industry of a specified measuring instrument used at his/her place of business pertaining to the designation, if the performance of such a repaired specified measuring instrument conforms to the technical standards specified by the Ordinance of the Ministry of Economy, Trade and Industry and the instrumental error of such a repaired specified measuring instrument does not exceed the tolerance for use specified by the Ordinance of the Ministry of Economy, Trade and Industry.発音を聞く  - 日本法令外国語訳データベースシステム