意味 | 例文 (999件) |
MM methodとは 意味・読み方・使い方
追加できません
(登録数上限)

「MM method」の部分一致の例文検索結果
該当件数 : 1310件
As an improving method, the Sm/Ra in the center part of the roll is regulated to 0.03-0.08 (mm/μm) and the Sm in the same part is regulated to 0.1-0.4 mm.例文帳に追加
改良法として、ロール中央部のSm/Ra を0.03〜0.08(mm/μm)に、且つSmを0.1〜0.4mm に規定する。 - 特許庁
In the method for reducing the volume of the porous particle, the porous particles are pulverized to the average particle size of 0.2 to 0.6 mm or to the maximum particle size of 0.5 mm to 1.0 mm.例文帳に追加
多孔質粒子を平均粒径0.2〜0.6mm又は最大粒径0.5〜1.0mmに粉砕する。 - 特許庁
And in the press-contact method, as the annular body 2, a material with 1,0-4.0 mm in thickness and 2.0-5.0 mm width may preferably be used.例文帳に追加
この時、環体2として厚さが1.0mm〜4.0mmで、幅が2.0mm〜5.0mmのものを使用すると良い。 - 特許庁
CYLINDRICAL MM TYPE LINEAR MOTOR AND MANUFACTURING METHOD FOR NEEDLE TEREOF例文帳に追加
円筒MM型リニアモータとその可動子製造方法 - 特許庁
DEVICE AND METHOD FOR PROCESSING MOBILITY MANAGEMENT (MM) BACK-OFF例文帳に追加
移動管理(MM)バックオフを処理する装置及び方法 - 特許庁
This method is suitable for forming the continuous groove 103 with a width of 60 mm or below and a depth of 60 mm or below.例文帳に追加
幅60mm以下、深さ60mm以下の連続溝103の形成に適する。 - 特許庁
In the continuous casting method, after completing casting, a varying speed V (mm/sec) and a varying quantity S (mm) of the molten steel surface of an unsolidified part within the cast slab during extracting the cast slab satisfy the following equation (1) to (6).例文帳に追加
鋳込終了後、鋳片引抜中の鋳片内の未凝固部湯面の変化速度V(mm/sec)および変化量S(mm)が下記の 〜 式を満たす連続鋳造方法。 - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解! -
「MM method」の部分一致の例文検索結果
該当件数 : 1310件
To provide a method for producing a high-tension steel having a tensile strength of ≥570 N/mm^2 and excellent weld crack resistance.例文帳に追加
引張強さ570N/mm^2以上の耐溶接割れ性に優れた高張力鋼の製造方法を提供する。 - 特許庁
The test conditions are: the electrodes of ϕ25 mm cylindrical column/ϕ25 mm cylindrical column; the sample thickness of 0.5 mm; the test method of short time process; and the test temperature of 23°C.例文帳に追加
<試験条件> 電極:φ25mm円柱/φ25mm円柱 試料厚み:0.5mm 試験方法:短時間法 試験温度:23℃ - 特許庁
The method for cutting the trimming chip produced in trimming the metal plates at their side ends using a side trimmer comprises controlling a clearance G (mm) and an overlap L (mm) between the upper and lower cutters of a chopper for cutting the trimming chip depending on the thickness t (mm) of the metal plates measured at the entry side of the side trimmer.例文帳に追加
サイドトリマーを用いて金属板の側端部をトリミングすることによって発生するトリミング屑の切断方法において、サイドトリマーの入側で測定した金属板の厚さt(mm)に応じて、トリミング屑を切断するチョッパーの上刃と下刃のクリアランスG(mm)とオーバーラップL(mm)とを調整する。 - 特許庁
A method for generating an image signal comprises the step of reading a radiological image at a sampling interval of 20 cycles/mm from a storage phosphor sheet obtained by photographing the image, by using grids of 4 lines/mm to obtain digital image data S1.例文帳に追加
4本/mmのグリッドを使用して放射線画像が撮影された蓄積性蛍光体シートから、サンプリング間隔を20cycle/mmとして放射線画像を読み取ってデジタルの画像データS1を得る。 - 特許庁
In the rubber strip winding method, a rubber strip of a width Wg 5-40 mm and a thickness Tg 0.3-3.0 mm is used.例文帳に追加
ゴムストリップ巻回方式において、巾Wg5〜40mm、厚さTg0.3〜3.0mmのゴムストリップを使用する。 - 特許庁
METHOD OF PRODUCING SHAPE-MEMORY ALLOY BOLT WITH OUTER DIAMETER OF ≥3 mm例文帳に追加
外径が3mm以上の形状記憶合金ボルトの製造方法 - 特許庁
To provide a method for evaluating a power supply cord of a diameter 8.5 mm or smaller.例文帳に追加
外径が8.5[mm]以下の電源コードの柔軟性を評価する。 - 特許庁
The method further comprises the step of removing the harmonic components by a filtering process, and sampling the data at 1/2 to obtain image data at a Nyquist frequency of 10 cycles/mm.例文帳に追加
高調波成分をフィルタリング処理により除去し、1/2にサンプリングして、ナイキスト周波数10cycle/mmの画像データを得る。 - 特許庁
|
意味 | 例文 (999件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
![]() ログイン |
Weblio会員(無料)になると
![]() |


![]() | 「MM method」のお隣キーワード |
weblioのその他のサービス
![]() ログイン |
Weblio会員(無料)になると
![]() |