let-38とは 意味・読み方・使い方

After thrusting the claws 42 and 43 of opened buckets 37 and 38 on the ground surface, by generating vibration on vibration cylinders 48 and 49 substituting one parts of links 46 and 47, the buckets 37 and 38 are vibrated to let the claws 42 and 43 bite in the ground surface easily and deeply.例文帳に追加

開放しているバケット37、38の爪42、43を地面に突き立てた後、リンク46、47の一部を代替している振動シリンダ48、49に振動を発生させると、バケット37、38が振動して爪42、43が地面に容易にかつ深く食い込む。 - 特許庁

An adsorbent element 31 of the humidity conditioner 20 is provided with a humidity conditioning side passage 38 and a cooling side passage 39, whereby during the adsorption operation for adsorbing moisture in air flowing through the humidity conditioning side passage 38 to an adsorbent, a cooling fluid is let flow through the cooling side passage 39 to rub heat of adsorption generated in the humidity conditioning side passage 38.例文帳に追加

調湿装置（20）の吸着素子（31）に、調湿側通路（38）と冷却側通路（39）とを設け、調湿側通路（38）を流れる空気中の水分を吸着剤に吸着させる吸着動作時に冷却側通路（39）に冷却用流体を流して、調湿側通路（38）で生じる吸着熱を奪うようにする。 - 特許庁

In the method, an X-ray receiving region 28 is covered with a mask 38 to let a first reflection optical path 26-1 receive light more than a third reflection optical path 26-3.例文帳に追加

Ｘ線の受光領域（２８）にマスク（３８）を被せて、第１の反射光路（２６−１）を第３の反射光路（２６−３）よりも多く受光させる。 - 特許庁

When the top plate 38 is pulled up until it hits the bottom face of the terminal piece 18 with the bending deformation of the locking piece 43, the locking piece 43 makes a restoring deformation to let the protrusion 44 get into the underside of the rear edge of the top plate 38 for locking.例文帳に追加

係止片４３が撓み変形しつつ上板３８が端子片１８の下面に当たるまで引き上げられると、係止片４３が復元変形して突部４４が上板３８の後縁の下面側に入り込んで係止する。 - 特許庁

At an image non-form time, toner particles 38 on the recording roller 30 are let to fly towards the holes 56 of the substrate 50 at a speed higher than at an image form time, whereby the interior of the holes 56 is cleaned.例文帳に追加

非作像時に、記録ローラ３０上のトナー粒子３８を基板５０の孔５６に向けて作像時よりも高速で飛翔させることによって孔５６の内部をクリーニングする。 - 特許庁

The combustion gas of a burning heater 91 is introduced into an exhaust passage 42 between a HC absorbent 38 and a catalyst converter 39 when an engine is started so as to let the catalyst converter 39 be thereby warmed up.例文帳に追加

エンジン始動時に、燃焼式ヒータ９１の燃焼ガスを、ＨＣ吸着剤３８と触媒コンバータ３９との間の排気通路４２に導入し、触媒コンバータ３９を暖機する。 - 特許庁

This closed type compressor 1 is equipped with a compression mechanism 11 supported to the upper part of the inside of its closed housing 2 by way of a frame 6, a motor 38 driving the compression mechanism 11 with its rotating shaft 41, and an oil pump 49 to be driven by the rotating shaft 41 so as to let lubricant be fed to the compression mechanism 11.例文帳に追加

密閉型圧縮機1は、密閉ハウジング2内の上部にフレーム6を介して支持された圧縮機構11と；圧縮機構を駆動する回転軸41を有するモータ38と；回転軸によって駆動され、潤滑油を圧縮機構に供給する油ポンプ49と；を備えている。 - 特許庁