lug terminalとは 意味・読み方・使い方

The wireless terminal of this invention has a casing structure provided with an illegal decomposition detecting lug 30 with a thin thickness, or a thickness variable at positions of the lug, or with a notch by which the lug is damaged because of a load exerted by a decomposition force applied to the casing by a different decomposition procedure from a regular decomposition procedure.例文帳に追加

正規の分解手順とは異なる分解手順で筐体に分解の力が加わると、力の負荷によりツメが破損する肉厚の薄い、又は、肉厚が場所によって変化する、又は、切り欠きを有する違法分解検知用ツメ３０を備えた筐体構造を有する無線端末である。 - 特許庁

To prevent damage in a resin part due to contact of a part with another one or the like, and also to prevent falling-off of a lug part from the resin part due to the damage of the resin part caused when a lug terminal is put in and pulled out of a connector.例文帳に追加

部品同士等の接触による樹脂部の破損を防止することと、ラグ端子とコネクタを抜き差しする際の樹脂部の破損による、ラグ部の樹脂部からの脱落を防止することとを目的とする。 - 特許庁

A lug 13, formed at a base end of a conductive strip terminal member 12, is projected from a rear face in the vicinity of an inner circumference of a diaphragm 8 to a front side and fixed and a lead wire 10 of a vice coil is connected to the lug 13.例文帳に追加

導電性を有する帯状の端子部材１２の基端部に形成したラグ１３を振動板８の内周部近傍の裏面から表面側に突出せしめて固定し、該ラグ１３にボイスコイルのリード１０を接続する。 - 特許庁

A tip recessed part 18 is formed at a tip of a first extension part 16 of this lug terminal 10; and side recessed parts 22 are formed on second extension parts 20.例文帳に追加

ラグ端子１０の第１延出部１６の先端には先端凹部１８が形成されており、第２延出部２０にはサイド凹部２２が設けられている。 - 特許庁

(a) A bearing surface of the screw 34 reaches a screw fixing part 14 of the lug terminal 10, and then the screw fixing part 14 is pushed down and sunk toward a side of the printed circuit board 30.例文帳に追加

ねじ３４の座面がラグ端子１０のねじ取付部１４に当接すると（ａ）、ねじ取付部１４がプリント基板３０側に押されて沈む。 - 特許庁

Soldering is applied between a mounted terminal 105 provided on the lower face of the screw seat part 101 and the upper face of the printed board 110 to fix the lug terminal 100 to the printed board 110.例文帳に追加

ネジ座部１０１下面に設けられた実装端子１０５とプリント基板１１０の上面の間に半田付けがなされ、ラグ端子１００がプリント基板１１０に固定される。 - 特許庁

A metal terminal is provided for a shuttle lever, which is slid integrally with the shuttle lug 11, for make/break of electrical connection during movement in the sliding direction.例文帳に追加

シャトルつまみ１１と一体的にスライドするシャトルレバー１４には、スライド方向移動での電気的接続の断接を行う金属端子が設けられる。 - 特許庁

Even if solder wear occurs due to the change with the passage of time after soldering, the spacing projection 8 prevents shrinking of the spacing between the lug terminal 1 and the printed-circuit board 30.例文帳に追加

半田付け後の経時変化により半田やせが発生しても、スペーシング突起８がラグ端子１とプリント基板３０との間隔が縮まるのを防止する。 - 特許庁