flush boltとは 意味・読み方・使い方

Then, the member L2 is lowered by a turning operation of the fastening bolt 14b, so that the surface of the member L2 is adjusted so as to be flush with the surface of the member L1.例文帳に追加

次いで、締付ボルト１４ｂの回動操作により部材Ｌ２を下降させ、その面を部材Ｌ１の面と同一面に調整する - 特許庁

In a strong earthquake, the anchor bolt 11 is cut off by the flush plates 4 and 5 at a notch part 12 so as to operate a base isolation device.例文帳に追加

強震時には平滑板４，５でアンカーボルト１１を切欠部１２にて切断し、免震装置を動作させる。 - 特許庁

An anchor bolt 11 is passed through the flush plates 4 and 5 and the base 2 is fixed to the building 3 to prevent the building 3 from being swung and raised by wind pressure.例文帳に追加

平滑板４，５にアンカーボルト１１を貫通し、基礎２と建物３とを結合し、風圧による建物３の揺れや浮き上がりを防止する。 - 特許庁

Each of the binding ends 23 of the side stave 2 has a bolt hole 24 whose edge had an inclined surface 25. the binding end 23 is fit onto the spacer 15, and tightened and fixed with a flush bolt 26 and a nut 27.例文帳に追加

サイドステー２の結合端２３は孔縁が傾斜面２５になったボルト孔２４を有し、この結合端２３をスペーサ１５の外に嵌め、皿頭ボルト２６・ナット２７で締付けて固定する。 - 特許庁

In addition, a lubricant containing member 1B formed out of an elastic body which is flush with the upper surface of a guiding rail while covering the fixing bolt inserted into the inside of the bolt insertion hole 27 from the upper part, is engaged with the inside of the engaging groove 25.例文帳に追加

また、嵌合溝内に、上面が案内レールの上面と面一となり、ボルト挿通孔内に挿通した固定ボルトを上部から覆う弾性体からなる潤滑剤含有部材１Ｂを嵌合した。 - 特許庁

When a spare tire 30 is mounted on a rear part of a vehicle, the spare tire 30 is placed on a top face of a flush member 20, and fixed to a bracket 10 for fitting the spare tire via a fitting bolt 32 passing through a bolt hole in a wheel 31.例文帳に追加

スペアタイヤ３０を搭載する場合には、スペアタイヤ３０は、面一部材２０の上面に載置され、ホイール３１のボルト穴を挿通する取り付けボルト３２を介して、スペアタイヤ取付用ブラケット１０に固定される。 - 特許庁

After the secured bolt 1 is inserted through the securing hole 9 of the metal plate member 8, a head part 20 of the secured bolt 1 is pressed in by press work relating to the metal plate member 8 until the upper surface 20 of the head part 2 of the secured bolt 1 becomes flush with an upper surface 80 of the metal plate member 8.例文帳に追加

金属板部材８の固着孔９に固着ボルト１を通した後、プレス加工によって、固着ボルト１の頭部上面２０と金属板部材８の上面８０とが面一になるまで、固着ボルト１の頭部２０を金属板部材８に対して圧入する。 - 特許庁

Generation of any step is prevented by making a tap hole in the joint of the guide rails 1 and 2, screwing a bolt 11 with an adhesive applied there to threaded portion 12 thereof in this tap hole, removing a portion of the bolt 11 which is protruded from guide parts 1b and 2b of the guide rails, and finishing the joint to be flush using a rail file.例文帳に追加

ガイドレール１，２の継ぎ目部にタップ穴をあけ、この穴にねじ部１２に接着材を塗布したボルト１１を螺合し、その後ボルト１１のガイドレールの案内部１ｂ，２ｂから突出した部分を除去し、レールやすりで継ぎ目部を面一に仕上げることにより、段差の発生を防止する。 - 特許庁