意味 | 例文 (42件) |
一次応力の英語
追加できません
(登録数上限)
英訳・英語 primary stress
「一次応力」の部分一致の例文検索結果
該当件数 : 42件
次に、タイヤモデルの周方向に隣接する要素の応力とひずみとの少なくとも一方を順次取得し、応力とひずみとの少なくとも一方の変化履歴を作成する(ステップS104)。例文帳に追加
Next, at least one of the stress and stain of an element adjacent in the peripheral direction of the tire model is successively acquired, and a change history of at least one of the stress and the strain is created (Step S104). - 特許庁
第二百四十一条 前条第三項第一号の材料の許容応力の値は、次に定めるところによる。例文帳に追加
Article 241 The value of allowable stress of materials set forth in item (i) of paragraph (3) of the preceding Article shall comply with the following provisions:発音を聞く - 日本法令外国語訳データベースシステム
ドロー工程の後であってトリム・ピアス工程の前に応力制御工程を設定して、ドロー工程後の一次成形品W1の一部に局部加熱処理を施して残留応力を除去する。例文帳に追加
By setting stress controlling stage after a drawing stage and before a trimming/piercing stage, residual stress is removed by applying the local heat treatment to a portion of a primary formed part W1 after the drawing stage. - 特許庁
構造物を数値解析する構造解析装置であって、上記構造物に作用する一次応力及び二次応力と上記構造物のクリープ寿命とが関連付けられた応力寿命関連データを記憶する記憶手段4と、上記応力寿命関連データに基づいて上記構造物の特性を算出する算出手段5とを備える。例文帳に追加
The structural analysis apparatus for numerically analyzing a structure includes a storage means 4 for storing stress-life-associated data in which primary stress and secondary stress acting on the structure and the creep life of the structure are associated with each other, and a calculation means 5 for calculating characteristics of the structure on the basis of the stress-life-associated data. - 特許庁
一 床材は、支点間隔及び作業時の荷重に応じて計算した曲げ応力の値が、次の表の上欄に掲げる木材の種類に応じ、それぞれ同表の下欄に掲げる許容曲げ応力の値を超えないこと。例文帳に追加
(i) The floor materials to be with bending stress calculated corresponding to the distance between fulcrums and the load applied during work not exceeding the value of allowable bending stress listed in the right column of the following table corresponding to the type of lumber listed in the left column of the same table.発音を聞く - 日本法令外国語訳データベースシステム
一般に、RC構造物の立ち上り部のコンクリートに発生する引張応力は、三次元温度応力解析の結果から、打継面の近傍の範囲が最も大きくなる。例文帳に追加
Generally, tensile stress generated in the concrete of the rising part of the RC structure becomes largest in a range near the construction joint surface from the result of three-dimensional temperature stress analysis. - 特許庁
次に、埋め込み配線7を覆うように、第一の層間絶縁膜上2に圧縮応力を有する膜(拡散防止膜8)を形成する。例文帳に追加
Then, a film (the diffusion preventing film 8) having compression stress is formed on the first inter-layer insulation film 2 so as to cover the embedded wiring 7. - 特許庁
-
履歴機能過去に調べた
単語を確認! -
語彙力診断診断回数が
増える! -
マイ単語帳便利な
学習機能付き! -
マイ例文帳文章で
単語を理解!
「一次応力」の部分一致の例文検索結果
該当件数 : 42件
データベース101は、応力特性(応力σ及び応力の磁化容易軸からの傾き角θ_Bσ)をパラメータの一つとした任意の励磁条件における二次元ベクトル磁気特性を測定できる二次元磁気測定装置を用いて、各励磁条件における各種磁性材料の二次元ベクトル磁気特性を測定し、その結果をデータベース化したものである。例文帳に追加
A database 101 is created by using a two-dimensional magnetism measuring apparatus for measuring two-dimensional vector magnetic characteristics under excitation conditions with stress characteristics (stress σ and an inclination angle θ_Bσ from the axes of easy magnetization of stress) as one of parameters, measuring the two-dimensional vector magnetic characteristics of each kind of magnetic material in each excitation condition, and databasing the result. - 特許庁
なお、前記第1次圧縮応力付加強制冷却の完了後、ストランドの軸心部の温度が(Ts−255)℃となるまで下記(2)式により与えられるQ_2により第2次圧縮応力付加強制冷却を行うのが一層望ましい。例文帳に追加
It is further preferable that, after completion of the addition of the primary compression stress and forcible cooling, forcible cooling with secondary compression stress added by Q_2 given by the following expression (2) is carried out until the temperature of the axial core part of the strand reaches (Ts-255)°C. - 特許庁
一次コイル,二次コイルなどの巻線と配線および鉄心とを一体に樹脂モールドする際に発生する熱応力は鉄心が縮まず、樹脂が縮もうとするために発生する。例文帳に追加
Thermal stress generated when the windings such as the primary coil and the secondary coil, the wiring and the iron core are integrally resin- molded is generated when the iron core does not shrink and the resin starts shrinking. - 特許庁
点火コイル1は、一次コイル21、二次コイル22、磁性部品4及び応力緩和部材51を収容するケース3内の隙間に熱硬化性樹脂11を充填してなる。例文帳に追加
The ignition coil 1 is formed by charging the thermosetting resin 11 into a gap in a case 3 for storing the primary coil 21, the secondary coil 22, the magnetic component 4, and the stress relaxing member 51. - 特許庁
本発明による光ファイバの心線対照装置は、光ファイバの長手方向に複数の応力を付与し、一時的なグレーティングを形成する応力付与部と、グレーティングで生じる高次モードの漏洩光を検知する受光部とを備える。例文帳に追加
The fiber identification apparatus for an optic fiber includes a stress applying part for applying a plurality of stresses in a longitudinal direction of the optic fiber for forming temporary grating, and a light receiving part for detecting leakage light of a high-order mode caused by the grating. - 特許庁
三次元金属多孔体10に支持体として接合させる多孔性導電性薄板9の厚みを10〜100μm未満、開口率を30%〜70%に、開口孔径を0.5〜3.0mm、に設定し、製造時に極板の一部に圧縮応力が作用するような曲げ応力が生じた際に、極板の支持体自体が伸長し圧縮応力を緩和するような構造とする。例文帳に追加
The thickness of a porous conductive thin sheet 9 connected to a three-dimensional metal porous body 10 as a support is set to 10-100 μm, the numeric aperture is set to 30-70%, and the aperture bore diameter is set to 0.5-3.0 μm. - 特許庁
更に、二つの一次シール部の間を集束し、二次シールS2を施すことにより、一次シールの端部に応力が集中することもなくなり、シール部の強度の低下が防止された充填包装体を製造する充填包装装置および充填包装体の製造方法が提供される。例文帳に追加
Furthermore, the space between the two primary seals is collected for providing a secondary seal S2, thereby eliminating convergence of stress on the end portion of the primary seal, thus making for the provision of the manufacturing method of filling and packaging apparatus and of the filled package body for the production of the filled package body whose strength at seal portion is prevented from deteriorating. - 特許庁
過冷却状態の合金5が凝固潜熱によって結晶化する前に、合金5に一次応力を加えることにより、異方化したR_2Fe_14B型結晶相をα−Feよりも優先的に成長させる。例文帳に追加
Before the supercooled alloy 5 is crystallized by latent heat of solidification, a primary stress is applied to the alloy 6 to make an anisotropic R_2Fe_14B crystal phase grow with higher priority than an amorphous Fe phase. - 特許庁
|
意味 | 例文 (42件) |
|
ピン留めアイコンをクリックすると単語とその意味を画面の右側に残しておくことができます。 |
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |
weblioのその他のサービス
ログイン |
Weblio会員(無料)になると 検索履歴を保存できる! 語彙力診断の実施回数増加! |