back-up screwとは 意味・読み方・使い方

The screw is sized to provide a guide 4 which projects up to a point rather than a back surface of a head 3 of the screw around a peripheral direction whole circumference of the head 3 of the screw or at two or more places and to be capable of covering inner diameter of the guide 4 around the outer periphery of a washer.例文帳に追加

螺子類の頭部３の周方向全周又は二以上の個所に、螺子類の頭部３裏面よりも先まで突出するガイド４を突設し、ガイド４の内径を座金の外周に被せることのできる寸法とした。 - 特許庁

A headless screw member 14 is screw-engaged with an anchor fitting 13 inserted in an undercut hole 12a at the back of the ceramic panel 12, and engaged and held in the undercut hole 12a by enlarging the diameter of an anchor part 13a, and one end of a hanger metal 15 is fixed in a space up to the back of the ceramic panel 12 by the anchor fitting 13.例文帳に追加

セラミックパネル１２の裏面のアンダーカット穴１２ａに挿入したアンカー金具１３に頭なしネジ部材１４を螺合し、アンカー部１３ａを拡径してアンダーカット穴１２ａに係合保持すると共に、そのアンカー金具１３によりセラミックパネル１２の裏面との間に吊下げ金具１５の片端を固定する。 - 特許庁

This grooving apparatus is provided with a grooving roll and a back-up roll which are relatively displaced with a feed screw and, by improving the strength and durability of the feed screw, preventing its wear and improving torque performance, the grooving of a thicker pipe is made possible.例文帳に追加

本発明の溝付け装置は、送りねじにより相対変位する溝付けロール及びバックアップロールを備え、送りねじの強度及び耐久性を向上させ、その磨耗を防ぎ、トルク性能を向上させることにより、より厚肉のパイプの溝付けが可能となる。 - 特許庁

On the occasion of changing over the target value toward lowering of the pressure in the heating barrel 12 in the course of the follow-up pressure process, the pressure is reduced by moving back a screw 14 at a prescribed speed in the heating barrel 12.例文帳に追加

保圧工程中に加熱バレル１２内の圧力を下げる方向に目標値を切り替える際、加熱バレル１２内でスクリュ１４を一定速度で後退させることにより圧力を減少させる。 - 特許庁

Namely, when the screw W is supplied to the guide section 30, the detection lever 36 is pushed back by resisting urging force of a spring 40, and is set up at an ON state wherein the magnet 42 and the hall element 46 are faced each other.例文帳に追加

即ち、ネジＷがガイド部３０に供給される場合には、検出レバー３６はバネ４０の付勢力に抗して押戻されマグネット４２とホール素子４６とが対向するオン状態となる。 - 特許庁

An axis direction of the terminal screw 22 is slanted against a back-and-forth direction (an up-and-down direction in the figure), whereas, the rotation limiting part 12d fitted on an inner face of the terminal housing recess part 12 in contact with the washer 23 for limiting rotation of the washer 23 is also slanted like the terminal screw 22.例文帳に追加

端子ねじ２２の軸方向は前後方向（図の上下方向）に対して傾斜しているが、端子収納凹部１２の内面に設けられ座金２３に当接して座金２３の回転を制限する回転制限部１２ｄも、端子ねじ２２と同様に傾斜している。 - 特許庁

Notches 4 and 5 are provided in the back metal 2 and the edge of shank of the saw blade plate 1, and by shallowing the notch 4 of the plate 1, the plate 1 is pushed up with the top of a screw 6 threaded from under the helve 3 so that the plate 1 is brought into close contact with the inner upper edge of the back metal 2.例文帳に追加

背金２及び鋸刃板１の中子部分の下縁に切欠部４、５を設け、鋸刃板１の切欠部４を浅く形成することによって、把持柄３の下方から螺入させたねじ６の先端で鋸刃板を押し上げ、背金２の内面上縁に密接させる。 - 特許庁

In the structure where a front is cut and divided radially as seen from the front at a bridge portion, the lens is fit by opening the rim up and down, and then divided surfaces are screwed up, a nut made of metal is inserted from a back side of an upper bridge, and a male screw is put through from the downside of a lower bridge to be screwed with the nut.例文帳に追加

フロントをブリッジ部分で、前方から見て放物線状に切り分け、リムを上下に開いてレンズを嵌め、その後分割面をネジで締付ける構造において、金属製ナットを上側ブリッジの裏側から挿入し、下側ブリッジの下方から雄ネジを通して、前記ナットに螺合させる。 - 特許庁