| 意味 | 例文 |
constant- currentの部分一致の例文一覧と使い方
該当件数 : 4593件
Drive switches SX1 to SX3 are turned off to cut anode lines A 1 to A 3 of organic EL elements E11 to E32 off from constant current sources I1 to I3 of a data line drive circuit 2 and to suck a current by a constant current source 10 of the voltage set circuit 6.例文帳に追加
ドライブスイッチSX1〜SX3をオフにして、有機EL素子E11〜E32の陽極線A1〜A3をデータ線駆動回路2の定電流源I1〜I3から切断し、電圧設定回路6の定電流源I0で電流を吸い込む。 - 特許庁
A current mirror circuit, composed of a P-channel MOS transistors TP01 and TP02 in an operation current control section 1100 controls the operation current of a ring oscillator circuit 1200, in response to a constant current flowing through itself.例文帳に追加
動作電流制御部1100中のPチャネルMOSトランジスタTP01およびTP02から成るカレントミラー回路は、自身を流れる定電流値に応じてリングオッシレータ回路1200の動作電流を制御する。 - 特許庁
The subscriber loop interface circuit uses a highly efficient constant DC current source and the current source is realized by using a switched mode current boost converter or a switched mode voltage-current transconverter 100.例文帳に追加
加入者ループ・インターフェース回路は、高効率の定DC電流ソースを用い、この電流ソースは、スイッチト・モード電流ブースト・コンバータまたはスイッチト・モード電圧−電流トランスコンバータ100のいずれかを使用して実現する。 - 特許庁
A first and a second current mirror circuits 12, 13 operating, based on a constant current supplied from a current source, are connected in serial between a current source 11 and a power supply GND at a low- potential side.例文帳に追加
電流源11から供給される定電流に基づいて動作する第一及び第二のカレントミラー回路12,13が電流源11と低電位側電源GNDとの間で直列に接続される。 - 特許庁
A current mirror circuit consisting of transistors Q1, Q2 allows a current supplied from a constant current source CS1 to flow into a transistor Q3 as a current corresponding to an emitter area ratio between the transistors Q1, Q2.例文帳に追加
定電流源CS1により供給された電流をトランジスタQ1,Q2からなるカレントミラー回路により、トランジスタQ1とトランジスタQ2とのエミッタ面積比に応じた電流をトランジスタQ3に流す。 - 特許庁
Since the drain current of the MOS TR T3 is determined by a current flowing from the constant current source 9, the gate voltage of the MOS TR T1 is reset so as to be a value corresponding to the drain current.例文帳に追加
このとき、MOSトランジスタT3のドレイン電流が定電流源9から流れる電流によって決まるため、MOSトランジスタT1のゲート電圧がこのドレイン電流に応じた値となるようにリセットされる。 - 特許庁
In the digital/analog converter, the difference current IS between a current ICS flowing through a MOS transistor(TR) 102 acting like a constant current source and a current ISET flowing through a resistor RSET to generate a monitor voltage given to an operational amplifier 101 is adjusted.例文帳に追加
定電流源としてのMOSトランジスタ102を流れる電流I_CSと、オペアンプ101に入力されるモニタ電圧を生成するための抵抗R_SETを流れる電流I_SETとの差分電流I_Sを調整する。 - 特許庁
A power circuit 16 lights a lamp by supplying a current to the lamp 15 connected to the secondary side of a current transformer 12 from a constant current power device 11 connected to the primary side of the current transformer 12.例文帳に追加
電源回路16は、変流器12の一次側に接続された定電流電源装置11から変流器12の二次側に接続された灯火15に電流を供給して灯火を点灯させる。 - 特許庁
Since the maximum value of the electric current supplied to a current-controlled oscillation circuit 5 varies, depending upon the value of the circuit I3, the oscillation of the oscillation circuit 5 will not stop, if the current value of the constant- current circuit I3 is set.例文帳に追加
電流制御型発振回路5に供給する電流の最大値は、定電流回路I3の値で決定されるため、定電流回路I3の電流値を設定しておけば、発振が停止することはない。 - 特許庁
The MN 12, MN13 have a 10 μA constant current source MN10, active load current mirror circuits MP10, MP1, and MP11 for load adjustment, and a current error compensation input current mirror circuit MN11.例文帳に追加
MN12、MN13には10μAの定電流源MN10および能動負荷カレントミラー回路MP10およびMP1、さらに負荷調整要としてMP11、電流誤差補償入力カレントミラー回路MN11がある。 - 特許庁
The difference in voltage between the current detection terminal and a voltage reference terminal is substantially constant when a current to be detected through the current detection circuit is substantially equal to a first threshold value for current detection.例文帳に追加
電流検知端子と電圧基準端子の間の電圧差は、電流検知回路によって検知しようとする電流が第1の電流検知しきい値と実質的に等しい場合に実質的に一定となる。 - 特許庁
The constant current source circuit is provided with a reference current source 11 for supplying driving current, and a current mirror circuit 12 for turning back a current supplied from the reference current source 11 to supply it to the differential amplifier circuit 2, wherein a resistor R3 is disposed between the current mirror circuit 12 and the differential amplifier circuit 2.例文帳に追加
駆動用の電流を供給する基準電流源11と、その基準電流源11から供給された電流を折り返して、その電流を差動増幅回路2に供給するカレントミラー回路12とを備え、カレントミラー回路12と差動増幅回路2の間に抵抗R3を配置する。 - 特許庁
A current source circuit is characterized in that the value of a signal current supplied from the current source circuit having a plurality of current sources disposed for respective wiring lines is so set as to supply a predetermined signal current using a constant current source for reference, and electric connections between wiring lines to which the signal current is output and the current sources are changed in every certain period.例文帳に追加
各配線に配置された複数の電流源を有する電流源回路から供給される信号電流の値を、リファレンス用定電流源を用いて、所定の信号電流を供給するように設定し、さらに信号電流が出力される配線と電流源との電気的な接続をある期間ごとに切り換える。 - 特許庁
A charging controller 13 operates using a constant voltage from a constant voltage diode 17 as the drive power, charges an electric double layer capacitor 5 with a specified constant current, and controls a power semiconductor circuit 4 so that a constant voltage is attained after reading the upper limit value.例文帳に追加
充電コントローラ13は、定電圧ダイオード17からの定電圧を駆動電源として動作し、電気二重層キャパシタ5を所定の定電流で充電し、上限値に達すると以降定電圧となるようパワー半導体回路4を制御する。 - 特許庁
Furthermore, the input terminal 11 is connected through a constant current source 25, a time constant terminal 14 and a capacitor 6 for time constant are connected to the ground terminal 5, and this time constant terminal 14 is connected through an operational amplifier 28 to the base of the transistor 18.例文帳に追加
さらに入力端子11が定電流源25、時定数端子14、時定数用のコンデンサ6を通じて接地端子5に接続され、この時定数端子14が演算増幅器28を通じてトランジスタ18のベースに接続される。 - 特許庁
To provide a drive circuit capable of suppressing variations of a charging time constant or of a discharging time constant without increasing the number of resistors determining the charging time constant or the discharging time constant of a drive current path of a capacitive load.例文帳に追加
容量性負荷の駆動電流路の充電時定数又は放電時定数を決定する抵抗器の数を増加させることなく、充電時定数又は放電時定数のばらつきを抑えることができる駆動回路を提供することを目的とする。 - 特許庁
To estimate an accurate time constant in which an error due to a vibration such as a waveform current ripple or the like is removed from a response waveform of a torque axis voltage reference when an exciting current reference is changed stepwise in a constant speed state without necessity of a measuring instrument for tuning and to set the time constant as a secondary time constant to a motor controller.例文帳に追加
チューニングのための測定器を必要とせず、速度一定状熊で励磁電流基準をステップ変化させたときのトルク軸電圧基準の応答波形から、波形の電流リプルなどの振動による誤差を除去した正確な時定数を推定し、これを二次時定数として装置に設定する。 - 特許庁
Next, when a non-load current value which is a current value when non-load rotation of the motor is set to Inl, and a correction torque constant which is a constant different from the back electromotive force constant is set to Ktz, the device for calculating the characteristics of the motor calculates the correction torque constant according to the formula Ktz=Tst/(Ist-Inl).例文帳に追加
次に、電動機の特性を算出する装置は、電動機の無負荷回転時における電流値である無負荷電流値をInlとし、逆起電力定数とは異なる定数である補正トルク定数をKtzとした場合において、Ktz=Tst/(Ist−Inl)の式にしたがって、補正トルク定数を算出する。 - 特許庁
Further, a constant current which is twice as large as a sense current Is supplied from a current supply circuit 52 to the memory cell, i.e. 2*Is is supplied to the dummy memory cell DCP.例文帳に追加
さらに、ダミーメモリセルDCPに対して、電流供給回路52からメモリセルに供給されるセンス電流Isの2倍、すなわち2・Isの一定電流が供給される。 - 特許庁
During a reception period, the value of a current flowing to the signal line 3 is kept at a fixed value, which is set by a current control signal Iref, by a constant current control circuit 36.例文帳に追加
また、受信期間では、定電流制御回路36により信号線3に流れる電流値が電流制御信号Irefにより設定された一定値に保たれる。 - 特許庁
Current values are limited by the current control circuits 12, 13, thereby charging and discharging the piezo-electric element with a constant current, and a linear sawtooth-like voltage is applied to the piezo-electric element.例文帳に追加
電流制御回路12,13によって電流値を制限することにより、圧電素子の定電流充放電を行い、直線的な鋸歯状電圧を圧電素子に印加する。 - 特許庁
A test mode is set in this D/A converter 100 and a current switch 50 for a test is turned ON and OFF in linkage with the current switch 20-1 of the constant current source 10-1 of a lowest order.例文帳に追加
D/Aコンバータ100でテストモードに設定し、テスト用の電流スイッチ50が最下位の定電流源10−1の電流スイッチ20−1と連動してオン、オフする。 - 特許庁
Accordingly, a current flowing through a current setting resistor R_9, i.e. a Hall element driving current I_H becomes I_H=V_dv/R_9 [A], and is constant irrespective of the internal resistance of the Hall element 16.例文帳に追加
したがって、電流設定用抵抗R_9に流れる電流すなわちホール素子駆動電流I_Hは、I_H=V_dv/R_9[A]となり、ホール素子16の内部抵抗によらず一定となる。 - 特許庁
Then, a switching element Q1 for a power adjustment is controlled on/off so that a total current of a current I2 of the second capacitor C2 and a current I3 of the discharge lamp La can be constant.例文帳に追加
そして第2コンデンサC2の電流I2および放電灯Laの電流I3の合計電流が一定となるように、電力調整用スイッチング素子Q1をオン/オフ制御する。 - 特許庁
To provide a source follower circuit having a current source improved in constant current characteristics, a laser driving device provided with this circuit, a semiconductor laser device, a current/voltage converting circuit and a photodetector circuit.例文帳に追加
定電流特性を改善された電流源を有するソースフォロア回路、これを含むレーザ駆動装置、半導体レーザ装置、電流電圧変換回路および受光回路を提供する。 - 特許庁
For employing a current output type comparator for a PLL circuit phase comparator 1 and for shortening the settling time, a constant-current source 2 is connected to the output terminal of the current output type phase comparator 1.例文帳に追加
PLL回路の位相比較器1を電流出力型とし、セットリング時間を短縮するために、電流出力型位相比較器1の出力端に定電流源2を接続する。 - 特許庁
As a result, the output current I1=Ia becomes constant, the amount of increase in the load current Io over the operation point P is captured by the output current I2 and is supplied to the load.例文帳に追加
これにより、出力電流I1=Ia一定となり、動作点Pを超える負荷電流Ioの増加分は出力電流I2により補われて負荷へ供給されることとなる。 - 特許庁
A peak voltage of the primary current is fixed to a predetermined reference voltage by the compensating functionality of the compensation signal to maintain an output current of the constant current circuit in a fixed condition.例文帳に追加
該一次電流のピーク電圧は該補償信号の補償働きによって、所定の参照電圧に固定させ、該定電流回路の出力電流を一定状態に維持する。 - 特許庁
A light-emitting diode illumination device 10 includes: a rectifier D1; a holding current maintaining circuit 18; a constant current circuit 20; a holding current limiting circuit 22; and a light-emitting diode load 24.例文帳に追加
発光ダイオード照明装置10は、整流器D1と、保持電流維持回路18と、定電流回路20と、保持電流制限回路22と、発光ダイオード負荷24とを有するものである。 - 特許庁
The DC current generating circuit 30 allows a DC current between the inverter device 20 and the inverter device 70 to be a constant current according to drive signals DRV1, 2 from the control unit 70.例文帳に追加
直流電流生成回路30は、制御装置70からの駆動信号DRV1,2に応じてインバータ装置20とインバータ装置70との間の直流電流を定電流にする。 - 特許庁
A constant current element Q2 is connected in series to the switching element Q1, and turns the switching element Q1 off when a current of the switching element Q1 becomes more than a predetermined current value.例文帳に追加
定電流素子Q2は、前記スイッチング素子Q1に直列に接続され、前記スイッチング素子Q1の電流が所定の電流値を超えたとき前記スイッチング素子Q1をオフさせる。 - 特許庁
Moreover, a current value to be supplied to the current source 15 as the reference is made so as to be varied by transistor operation, and a variation amount of the output current is made constant.例文帳に追加
また基準となる電流源15に供給する電流値をトランジスタの操作により変更できるようにしたことで、出力電流値の変化量を一定とするようにした。 - 特許庁
To provide an amplifier circuit with a current limiter which does not need a switching operation between a feedback loop mode and a constant current control mode, is quickly operable and has high stability in output current.例文帳に追加
フィードバックループモードと定電流制御モードの切替動作を不要とし、迅速に動作可能で、出力電流の安定性が高い電流リミッタ付き増幅回路を提供する。 - 特許庁
To provide a transmission and distribution apparatus capable of reducing an influence caused by a wraparound of high-frequency leakage current, ground current, constant leakage current or the like, and operating a ground leakage breaker positively.例文帳に追加
高周波漏れ電流、地絡電流、常時漏れ電流等の回り込みによる影響を低減し、漏電遮断器を確実に動作させることができる送配電装置を提供する。 - 特許庁
To provide a switching constant current power supply device capable of stabilizing a load current even if the current flowing a load (for example, a display device containing LED) repeatedly intermits.例文帳に追加
負荷(例えば、LEDを含む表示装置等)に流れる電流が断続を繰返す場合でも当該負荷電流を安定化することのできるスイッチング定電流電源装置を提供する。 - 特許庁
A pulse generation circuit is constituted of a first differential pair to be driven with a constant current source, second and third differential pairs to be driven with current smaller than that of the current source.例文帳に追加
パルス発生回路は、定電流源で駆動される第1の差動対と、前記電流源よりも小さな電流で駆動される第2及び第3の差動対とで構成される。 - 特許庁
To provide an over-current protection circuit for protecting a constant voltage circuit only by a fold-back-type over-current protection circuit by suppressing a deviation in detection values of the fold-back-type over-current protection circuit.例文帳に追加
フの字型の過電流保護回路の検出値のずれを抑制し、フの字型の過電流保護回路のみにて定電圧回路を保護する過電流保護回路を提供する。 - 特許庁
The operating current is supplied to the electrifier 21 and the destaticizer 24 by a constant current power supply circuit 100, and the sum of the operating current is maintained at the fixed value.例文帳に追加
定電流電源回路100により、帯電器21および除電器24にそれぞれ動作電流を供給するとともに、その各動作電流の合計を一定値に維持する。 - 特許庁
An alternating current power source obtained from the power generation section 21 is converted into a direct current power source and constant voltage by the charge section 20 and is supplied to the battery 19 at a fixed direct current voltage.例文帳に追加
発電部21から得られる交流電源は、充電部20で直流電源への変換及び定電圧にされて、一定の直流電圧でバッテリー19に供給される。 - 特許庁
Since a leakage current flowing through the Zener diode D1 is made sufficiently smaller than the current Ia of a constant-current circuit 3 under the state in which a switch 5 is turned on, the error of a mirror ratio is reduced.例文帳に追加
スイッチ5がオンした状態でツェナーダイオードD1に流れるリーク電流は、定電流回路3の電流Iaよりも十分に小さくなるので、ミラー比の誤差が小さくなる。 - 特許庁
A microcomputer 26 determines whether there is a change request associated with detection responsiveness of the O2 sensor 17, and determines a direction of the constant current flowing between the pair of sensor electrodes 33, 34 when determining that there is the change request and controls the constant current circuit 27 so that the constant current flows in the determined direction.例文帳に追加
マイコン26は、O2センサ17の検出応答性に関する変更要求の有無を判定し、変更要求が有ると判定された場合に、一対のセンサ電極33,34間に流れる定電流の向きを決定し、該決定した向きで定電流が流れるように定電流回路27を制御する。 - 特許庁
The power source line 12 is inserted with resistors R_s between the connection points of the respective constant current circuits and connection points of the adjacent constant current circuits on the upstream sides of the constant current circuits in order to compensate for the potential increase component of the common electrode wiring based on the resistor component (R_c) possessed by the common electrode wiring.例文帳に追加
コモン電極配線が有する抵抗分(R_c)にもとづくコモン電極配線の電位上昇分を補償するために、電源ライン124に、それぞれの定電流回路の接続点と、その定電流回路の上流側の隣接する定電流回路の接続点との間に抵抗R_sを挿入する。 - 特許庁
A PWM (pulth width modulation) circuit 14 operates a constant current circuit by the signal EN, and generates lamp waves.例文帳に追加
PWM回路14は信号ENによって定電流回路を動作し、ランプ波を発生する。 - 特許庁
A constant-voltage alternating-current power supply is connected across a series- connected circuit of the coils 5-1, 5-2, and 5-3.例文帳に追加
コイル5−1,5−2,5−3の直列接続回路の両端に定電圧交流電源を接続する。 - 特許庁
Constant current control is preferable for the first bias roller 10 and low voltage control is preferable for the second bias controller 11.例文帳に追加
第一バイアスローラ10は定電流制御、第二バイアスローラ11は低電圧制御が好ましい。 - 特許庁
To provide an LED driving circuit that can keep an LED current constant, thereby causing little power loss.例文帳に追加
LED電流を一定に保ち、且つ、電力損失が少なくて済むLED駆動回路の実現。 - 特許庁
The drive control unit 2 generates one piece of constant current, which circulates through the light-emitting member unit 3, and creates one piece of constant voltage at the direct-current voltage output side 33 of the light-emitting member unit 3, and the constant voltage is so structured for one piece of direct-current load 4 to use.例文帳に追加
その内に駆動制御ユニット2は一個の定電流を生じ、定電流は発光部材ユニット3を流通し、そして発光部材ユニット3の直流電圧出力側33において一個の定電圧を造り出し、定電圧は一個の直流負荷4が使用するのに用いるように構成されている。 - 特許庁
CONSTANT CURRENT DRIVING CIRCUIT OF ELECTRONIC LIGHT EMITTING ELEMENT AND ELECTRONIC LIGHT EMITTING ELEMENT DRIVING CIRCUIT OF LIGHTING FIXTURE FOR VEHICLE例文帳に追加
電子発光素子の定電流駆動回路及び車両用灯具の電子発光素子駆動回路 - 特許庁
When a voltage between both is increased in accordance with the increase of the potential, a constant current flows.例文帳に追加
そして、この上昇に応じて両者間の電圧を増大させることにより、一定電流が流れる。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|