| 例文 |
Pressure Relayの部分一致の例文一覧と使い方
該当件数 : 127件
This interlock comprises a pneumatic pressure relay, a pneumatic pressure line, and a pressure detection line.例文帳に追加
インターロックは、空気圧リレー、空気圧ライン、及び圧力検出ラインを含む。 - 特許庁
PNEUMATIC PRESSURE MONITORING UNIT, PNEUMATIC PRESSURE MONITORING SYSTEM, AND ON-VEHICLE RELAY UNIT例文帳に追加
空気圧監視ユニット、空気圧監視システム及び車載中継ユニット - 特許庁
In this way, atmospheric pressure is introduced into the relay tank 30, and water inside the relay tank 30 is sucked up from a suction pipe 37 to a relay tank 40 by a negative pressure inside the relay tank 40.例文帳に追加
これにより、中継槽30内に大気圧が導入され、中継槽40の負圧によって中継槽30内の水が吸上管37から中継槽40へ吸い上げられる。 - 特許庁
An impact pressure relay 1 is connected to a pressure introduction pipe 3 of a GIS 2 pressure container 2C.例文帳に追加
GIS2の圧力容器2Cの圧力導入管3に衝撃圧力継電器1を接続する。 - 特許庁
When a hose from a distributing truck is connected to a system, the pneumatic pressure line transfers pressurized air to the pneumatic pressure relay, and at the same time, the pressure detection line pressurizes the pneumatic pressure relay.例文帳に追加
空気圧ラインは、配送用トラックからのホースがシステムに連結されたとき、加圧空気を空気圧リレーに移送し、これと同時に圧力検出ラインが空気圧リレーを加圧する。 - 特許庁
DEVICE AND METHOD FOR POLISHING OPTICAL SUBMARINE RELAY PRESSURE CASING例文帳に追加
光海底中継器圧力筐体の磨き装置及び磨き方法 - 特許庁
To aim at downsizing of an electromagnetic relay capable of adjusting contacting point contact pressure.例文帳に追加
接点接触圧を調整可能な電磁継電器の小型化を図る。 - 特許庁
The specified pressure is the reference value that is stored in the meter relay 22.例文帳に追加
この所定の圧力は、メータリレー22に記憶された基準値である。 - 特許庁
A CPU 15 controls the control relay 16 using a pressure signal from the pressure sensor 7.例文帳に追加
そして、CPU15は圧力センサ7による圧力信号を用いて制御用リレー16を制御する。 - 特許庁
By this pressure, the piston of the pneumatic relay is displaced to match the arc-shaped passage of the relay to the pneumatic pressure valve so that the pressurized air can be moved to a pneumatic pressure valve in order to open the pneumatic pressure valve.例文帳に追加
この圧力により空気圧リレーのピストンを変位させ、リレーの円弧状通路を空気圧バルブと整合し、加圧空気を空気圧バルブまで移動できるようにし、これによって空気圧バルブを開放する。 - 特許庁
A pressure value of an amplified pneumatic pressure signal Pout, from a single action pilot relay 3, is detected by a pressure sensor 5, and sent to the calculating part 1.例文帳に追加
単動パイロットリレー3からの増幅空気圧信号Poutの圧力値を圧力センサ5によって検出し、演算部1へ送る。 - 特許庁
This pressure accumulation device 3 is provided for relay to accumulate air pressure fed from the air compressor 1 to be supplied to the work machine.例文帳に追加
エアーコンプレッサ1から送られてくる空気圧を蓄圧して作業機に供給する中継用の蓄圧装置3を設ける。 - 特許庁
The pressure value of the pressure control part 1 and a reference pressure 6 of a reference pressure generation device 5 and a pressure threshold by pressure switches 10a and 10b for making a relay 11 open/close the electromagnetic valve 9 are synchronously controlled, so that it is possible to control fluid control ranging from a low pressure to a high pressure with high sensitivity.例文帳に追加
圧力制御部1の圧力値と、基準圧力発生装置5の基準圧力6と、電磁弁9を開閉するリレー11を作動させる圧力スイッチ10a、10bによる圧力閾値とを同期して制御することで、低圧から高圧まで高感度な制御が可能となる。 - 特許庁
Since the hydraulic pressure in a space on the drain side of spaces inside a relay cylinder 104 partitioned by a relay piston 102 becomes high, the relay piston 102 moves in the direction X shown in Figure.例文帳に追加
すると、リレーシリンダ104内においては、リレーピストン102で仕切られた空間のうち、ドレン側の空間における油圧が高くなるので、リレーピストン102は、図のX方向に移動する。 - 特許庁
When the hose from the distributing truck is connected to the system, the pressure detection line detects a variation in pressure and pressurize the pneumatic relay.例文帳に追加
配送用トラックからのホースがシステムに連結されたとき、圧力検出ラインは圧力変化を検出し、空気圧リレーを加圧する。 - 特許庁
To provide a relay controller which is prevented from evaporation of moisture of a relay contact even if it is put in a low temperature environment and always assures sufficient contact pressure of the relay contact.例文帳に追加
低温環境下に置かれてもリレー接点部において水分が蒸発されるのを防止し、且つ、常に、十分なリレー接点部の接圧を確保することのできるリレー制御装置を提供する。 - 特許庁
When the high pressure switch PS is activated, a relay X1 is excited so as to open a normally closed point of contact X1-b cooperating with the relay and the compressor CM is stopped.例文帳に追加
高圧スイッチPSが作動すると、リレーX_1が励磁され、これと協働する常閉接点X_1−bが開放して圧縮機CMは停止される。 - 特許庁
For instance, if a mercury lamp is used for the high-pressure discharge lamp, the relay of the controllable short-circuiting means 14 is turned on, and if a high-pressure sodium lamp is used, the relay of the controllable short-circuiting means 15 is turned on.例文帳に追加
例えば、高圧放電ランプとして水銀ランプを用いる場合には、制御短絡手段14のリレーをオンにし、高圧ナトリウムランプであれば制御短絡手段15のリレーをオンにする。 - 特許庁
When a signal pressure is applied to a relay valve 70, the compressed air is fed from the relay valve 70 to the pressure chamber through a pipe port 26 and an outer peripheral part of a diaphragm 50 in a valve chamber 300.例文帳に追加
リレーバルブ70に信号圧が加わるとき、リレーバルブ70から配管ポート26および弁室300内のダイヤフラム50の外周部分を通して圧力室に圧縮空気を供給する。 - 特許庁
The brake oil pressure control device for controlling oil pressure supplied to a mechanical brake 21 according to a brake operation includes: a means (brake valve 40) which generates brake command oil pressure P1; a relay valve 50 which is opened according to the brake command oil pressure P1 and outputs brake control oil pressure P2; and a solenoid proportional valve 60 which adds pressure reduction command oil pressure P3 to the relay valve 50.例文帳に追加
ブレーキ操作に応じて機械式ブレーキ21への供給油圧を制御するブレーキ油圧制御装置に、ブレーキ指令油圧P1を発生する手段(ブレーキバルブ40)と、このブレーキ指令油圧P1を受けて開動作し、ブレーキ制御油圧P2を出力するリレーバルブ50と、このリレーバルブ50に減圧指令油圧P3を付加する電磁比例バルブ60と、を備える。 - 特許庁
A relay valve 16 installed in the driving air circuit has a signal pressure chamber connected in communication with the main air tank through a signal air passage 14, and compressed air having pressure complying with the pressure of the compressed air supplied to and exhausted from the signal pressure chamber is supplied and exhausted by the relay valve to/from the brake chamber.例文帳に追加
この駆動エア回路に設けられたリレーバルブ16が主エアタンクに信号エア通路14を介して連通接続された信号圧室を有し、このリレーバルブが信号圧室に給排される圧縮エアの圧力に応じた圧力の圧縮エアをブレーキチャンバに給排する。 - 特許庁
The pneumatic pressure relay comprises a housing for forming a chamber having a piston with arc- shaped passage disposed therein.例文帳に追加
空気圧リレーは、円弧状通路を持つピストンが内部に配置されたチャンバを画成するハウジングを含む。 - 特許庁
Compressed air compressed by an air compressor 11 is introduced to a spring chamber 12 for parking brake through a working pressure conduit 13 and a relay valve 14 to release the parking brake, and the compressed air is introduced to a signal pressure chamber of the relay valve through a signal pressure conduit 16 and a manual control valve 17 for parking brake to open the relay valve.例文帳に追加
エアコンプレッサ11により圧縮された圧縮エアを作動圧管路13及びリレーバルブ14を通り駐車ブレーキ用スプリングチャンバ12に導いて駐車ブレーキが解除され、上記圧縮エアを信号圧管路16及び駐車ブレーキ用手動制御弁17を通りリレーバルブの信号圧室に導いてリレーバルブが開く。 - 特許庁
The method is for pulling the tube 2 out to outside of the human body model dummy 6 and connecting it to a relay section, connecting to a pressure sensor and measuring the contact pressure.例文帳に追加
チューブ2を人体型ダミー6外部まで引き出し、中継部に接続し圧力センサに導き接触圧を計測する方法である。 - 特許庁
When a contact point of a sensor of a pressure meter is closed with a pressure rise to charge a relay terminal, the contact point is opened for turning without a trouble.例文帳に追加
しかし圧力計のセンサーが圧力の上昇で接点が閉じリレー端子へ荷電されると接点は開となり支障なく回転する。 - 特許庁
A relay valve 23 on the trailer 2 side receiving the air pressure outputted from the trailer control valve 11 as second signal pressure supplies air pressure of a trailer side air tank 22 as operating pressure to a trailer side brake part 21 to generate braking force.例文帳に追加
トレーラ制御バルブ11から出力される該エア圧を第2信号圧として受けたトレーラ側のリレーバルブ23は、トレーラ側エアタンク22のエア圧を作動圧としてトレーラ側ブレーキ部21に供給し、ブレーキ力を発生させる。 - 特許庁
If a liquid side high pressure switch SW2 or a gas side high pressure switch SW 3 is actuated in spite of this control, a main relay 52 is de-energized.例文帳に追加
この制御にもかかわらず、液側高圧スイッチSW2またはガス側高圧スイッチSW3が作動すると、メインリレー52が消勢される。 - 特許庁
When signal pressure is applied to a relay valve 70, a diaphragm 5200 of an on-off valve 50 in a valve chamber 300 is deformed.例文帳に追加
リレーバルブ70に信号圧が加わるとき、弁室300内の開閉弁50のダイヤフラム5200が変形する。 - 特許庁
To provide an impact pressure relay which enables saving power and also performing reliable SP detection.例文帳に追加
省電力を図るとともに、信頼性の高いSP検出ができる衝撃圧力継電器を提供する。 - 特許庁
When the pressure detected by the pressure sensor 34 becomes a predetermined pressure value or lower, the directional control valve 32 is switched so as to connect the relay valve 23 and the factory air source line 37.例文帳に追加
圧力センサー34で検出される圧力が所定の圧力値以下となったときに、切換弁32が中継弁23と工場空気源ライン37との間を接続するように切り換えられる。 - 特許庁
On the other hand, a first clutch apply relay valve 121 outputs a first preparatory oil pressure at the first to third forward speeds on the basis of the application pressure of a clutch C-2, and outputs a second preparatory oil pressure at the fourth to sixth forward speeds.例文帳に追加
一方、第1クラッチアプライリレーバルブ121は、クラッチC−2の係合圧に基づき前進1〜3速段で第1予備油圧を出力し、前進4〜6速段で第2予備油圧を出力する。 - 特許庁
To provide a pilot relay wherein it is possible to increase the speed of settling of the output air pressure, without increasing the bleed rate.例文帳に追加
ブリード量を大きくすることなく、出力空気圧の整定を早めることが可能なパイロットリレーを提供する。 - 特許庁
To provide a remote control relay which stabilizes a spring load of a contact pressure spring and also improves the workability of assembly work.例文帳に追加
接圧ばねによるばね負荷を安定させ、且つ、組立作業の作業性を向上させたリモコンリレーを提供する。 - 特許庁
When the high pressure switch PS is reset, the relay X1 is kept self-held and the compressor CM is kept stopped.例文帳に追加
高圧スイッチPSが復帰しても、リレーX_1は自己保持されており、圧縮機CMは停止状態に保持される。 - 特許庁
Solenoid valves of an auxiliary control unit for the brake pressure modulator produce air pressure in relation to a control space of a relay valve connected to the rear of the auxiliary control unit.例文帳に追加
ブレーキ圧力変調器のための予備制御ユニットの電磁弁は、予備制御ユニットの後に接続されたリレー弁の制御空間に関連して、気圧圧力を発生される。 - 特許庁
A relay valve 30 is controlled by a solenoid valve S1 and is changed between ports b and c to the position to circulate around a second pressure Psec and the position that circulates around a low holding pressure.例文帳に追加
リレーバルブ30は、ソレノイドバルブS1により制御され、ポートbとcとの間を、セカンダリ圧Psecを循環する位置と、低い保持圧を循環する位置に切換えられる。 - 特許庁
Pneumatic pressure output from the electropneumatic conversion relay valve 2 into a brake cylinder BC is detected by a pressure sensor 3, and the detected pressure is recorded as a reference value P_n (t) in a recording part 12.例文帳に追加
電空変換中継弁2からブレーキシリンダBCに出力される空気圧を圧力センサ3によって検出し、その検出した圧力検出値を記録部12に基準値P_n(t)として記録させる。 - 特許庁
In an oil passage g to input the line pressure P_L to the C-1 applied relay valve 23, an orifice 30 to regulate flow is provided.例文帳に追加
このC−1アプライリレーバルブ23にライン圧P_Lを入力する油路gに、流量を規制するオリフィス30を備える。 - 特許庁
To provide a hydraulic control device comprising a solenoid valve for supplying predetermined hydraulic pressure, and a relay valve for selectively changing over a supply destination for predetermined hydraulic pressure, wherein an unexpected relay valve change-over trouble can be reliably detected.例文帳に追加
所定の油圧を供給するソレノイドバルブと、その所定の油圧の供給先を選択的に切り換えるリレーバルブとを備えた油圧制御装置において、予定しないリレーバルブの切換異常を確実に検出することができる油圧制御装置を提供する。 - 特許庁
While the tube 12 is opened, a trigger signal is transmitted to a meter relay 22, and the pressure in the tube 12 which is detected by an atmospheric pressure sensor 17 is stored as a reference value.例文帳に追加
ここで、チューブ12内が開いた状態において、トリガ信号をメータリレー22に送って、大気圧センサ17が検知したチューブ12内の圧力を基準値として記憶させる。 - 特許庁
During a fail, because no modulator pressure is inputted to the oil chamber 21r1, the first clutch apply relay valve 21 is switched to the fail position, and a D-range pressure can be inputted to the hydraulic servo 41, 42, and a line pressure to the hydraulic servo 43.例文帳に追加
フェール時には、油室21r1にはいずれのモジュレータ圧も入力されないので、フェール時位置に切り換えられ、油圧サーボ41,42に対するDレンジ圧と,油圧サーボ43に対するライン圧の入力が可能となる。 - 特許庁
In redundancy, the redundant pressure is applied to a terminal which can be accessed from the outside of the redundancy selector valve, the pressure is enhanced via a relay valve portion of the braking pressure modulator, and it is transferred to the wheel brake cylinder.例文帳に追加
冗長の場合に、冗長切換え弁の外部からアクセス可能な端子に冗長圧力が加えられ、それからこの圧力は、ブレーキ圧力変調器のリレー弁部分を介して増強され、かつ車輪ブレーキシリンダに転送される。 - 特許庁
The tape comes up on the top face through a relay hole on this side of a pinhole, but it is put in a suitable position to which pressure is applied by a middle presser.例文帳に追加
針穴手前の中継穴からテープは上面にでるが、中押エによって圧力が加えられる適切な位置にある。 - 特許庁
When an on-off solenoid valve 60 is energized, first hydraulic pressure output from a control valve 70 is supplied through a relay valve 50 to a lockup clutch 14 and modulator pressure Pm is supplied through the relay valve 50 to a first assist chamber 33a of a first regulator valve 30.例文帳に追加
オンオフソレノイドバルブ60が通電状態の時に、コントロールバルブ70から出力された第1油圧がリレーバルブ50を通じてロックアップクラッチ14に供給され、かつ、モジュレータ圧Pmがリレーバルブ50を通じて第1レギュレータバルブ30の第1アシスト室33aに供給される。 - 特許庁
The common pressure portion 14 is disposed inside a relay block 16 as a non-covering area.例文帳に追加
そして、一方の電線10の被覆部30において、リレーブロック16内でかつ共圧部14に至る前の部分に部分切除部32が設けられている。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|