| 例文 |
switch terminalの部分一致の例文一覧と使い方
該当件数 : 3065件
When an engine stop switch 66 is depressed for instructing on the stop of an engine, one switch of an interlocking switch for connecting a power source side terminal 68 to a power reception side terminal 71 is opened, so that the ignition current is interrupted, the high voltage of an ignition coil 73 stops, the spark of a plug 74 disappears, and the engine 9 flames out.例文帳に追加
エンジン停止スイッチ66がエンジン停止指示のために押し込み操作されると連動スイッチの電源側端子68と受電側端子71を接続する一方のスイッチが開いて点火電流が遮断され、点火コイル73の高電圧が停止し、プラグ74のスパークが消失し、エンジン9が失火する。 - 特許庁
The receptacle is provided with a switch 21 making an On/Off operation in accordance with outer environment variation, first output terminal parts 13, 14 switching over between an output-allowed state and a shutoff state in interlocking with the operation of the switch 21, and a second output terminal part 12 capable of outputting power at all times without interlocking with the operation of the switch 21.例文帳に追加
外部環境変動によりON、OFF作動するスイッチ21と、スイッチ21の作動に連動して出力の可能状態と遮断状態とに切り替わる第1の出力端子部13、14と、スイッチ21の作動に連動することなく常時出力可能である第2の出力端子部12とを備えてなるコンセント。 - 特許庁
The power-window switch circuit has a transistor 33 grounding a gate terminal for a semiconductor switch 31A for elevating a window glass and grounding the gate terminal for the semiconductor switch 31B for lowering the window glass through a resistor R2B when a submersion detector 9 detects the submersion and diodes 32A and 32B.例文帳に追加
パワーウインドスイッチ回路は、浸水検出回路9が浸水を検出した際に、ウインドガラス上昇用の半導体スイッチ31Aのゲート端子を接地し、ウインドガラス下降用の半導体スイッチ31Bのゲート端子を、抵抗R2Bを介して接地するトランジスタ33と、ダイオード32A、32Bを備えている。 - 特許庁
A high side driving switch may be positioned between the negative terminal of the voltage source and the high side driver and operable to connect the high side driver to the negative terminal of the voltage source when the low side driver turns the low side bidirectional semiconductor switch on.例文帳に追加
電圧源の負端子とハイサイド駆動部との間にハイサイド駆動スイッチが配置され、ローサイド駆動部がローサイド双方向半導体スイッチをONにする時に、ハイサイド駆動部を電圧源の負端子に接続するよう動作可能であってよい。 - 特許庁
A slide switch is adopted for the switch 36 and its operating part, that is, a projection 36a can externally be operated through an operation hole 46d made to a bottom face 46b of a recessed part 46a for protecting the terminal Tb1 formed to a terminal board 36.例文帳に追加
このスイッチ36は、スライドスイッチからなり、その操作部である突起36aは、端子台36に形成された端末端子Tb1保護用の凹部46aの底面46bに穿設した操作孔46dを介して、外部から操作できる。 - 特許庁
The PIN diode 104 conducts when the slide switch 54 connects the push-pull amplifying stage 44 to the power supply terminal 50, and does not conduct when the slide switch 54 disconnects the push-pull amplifying stage 44 from the power supply terminal 50.例文帳に追加
このPINダイオード104は、スライドスイッチ54によってプッシュプル増幅段44が電源端子50に接続されたときに、導通し、スライドスイッチ54によってプッシュプル増幅段44が電源端子50から切り離されたときに、非導通となる。 - 特許庁
The option board 9 is provided with an external output terminal 7 for operating an AC switch (main power supply) 3 and a terminal to which power is supplied from a backup power supply 10 during no supply of power from the AC switch (main power supply) 3.例文帳に追加
更にオプションボード9にACスイッチ(メイン電源)3を操作するための外部出力端子7とACスイッチ8(メイン電源)3から電源が供給されない間、バックアップ用電源10から電源が供給されるような端子を設ける。 - 特許庁
A contact 10a of a changeover switch 10 is connected to the input terminal 2 and a power terminal of the uplink amplification stage 24, a contact 10b of the changeover switch 10 is connected to the input side of the downlink amplification stage 18, and connected to a DC power supply.例文帳に追加
切換スイッチ10の接点10aが入力端子2と上り増幅段の24の電源端子に接続され、切換スイッチ10の接点10bが下り増幅段18の入力側に接続され、かつ直流電源に接続されている。 - 特許庁
When the pressure force applied to the safety switch is opened, the deformed elastic conductive unit pushes the safety switch in a direction opposite to the pressure force, and the first connection terminal and the second connection terminal become in a disconnected state.例文帳に追加
前記安全スイッチにかかる前記圧迫力を開放した場合、変形した前記弾性導電ユニットは前記圧迫力と逆の方向に前記安全スイッチを押し、前記第一接続端子及び前記第二接続端子は断線状態となる。 - 特許庁
A jumper pattern 13 is fitted on an underside of a circuit board 1 of a switch, a wiring of the circuit board of an equipment is connected to one terminal 13a of the jumper pattern to shift to the circuit board of the switch, and is put back to circuit board of the equipment with the other terminal 13a.例文帳に追加
スイッチの回路基板1の下面にジャンパーパターン13を設け、機器の回路基板の配線をジャンパーパターンの一方の端子13aに接続してスイッチの回路基板に移し、他方の端子13aで再び機器の回路基板上に戻す。 - 特許庁
The communication repeater discriminates to which of the mobile communication network of the channel switch system or the mobile communication network of the packet switch a mobile terminal is connected when the communication repeater receives a connection request to the mobile terminal.例文帳に追加
この通信中継装置は,携帯端末に対する接続要求があった場合に,その携帯端末が回線交換方式の移動通信網,またはパケット交換方式の移動通信網の何れの網に接続されているかを判断する。 - 特許庁
Terminal parts 3a, 3a of a fingerprint authentication sensor 3 are provided projectingly downward from the lower face 22 of a key top 20a of a power switch 20, and electrodes 3c, 3c are provided in positions opposite to the terminal parts 3a, 3a, of a detection part 20b of the power switch 20.例文帳に追加
指紋認証センサ3の端子部3a,3aを電源スイッチ20のキートップ20aの下面22から下方へ突出して設け、電極3c,3cを電源スイッチ20の検出部20bの、端子部3a,3aに対向する位置に設ける。 - 特許庁
A communication control part 20 for the measuring element 17 and remote meter-reading is stored in an outer shell case body, and an address setting switch 21 and a communication mode setting switch 22 are provided in a terminal base part of a communication terminal 13b which is outside the case body.例文帳に追加
計測素子17および遠隔検針のための通信制御部20を外殻筐体内に収納し、筐体外である通信端子13bの端子台部にアドレス設定スイッチ21および通信モード設定スイッチ22を設けた。 - 特許庁
Further, a power switch terminal 20 and a power supply connector terminal 19 connected to a power ON/OFF switch 24 and a power supply connector 26, respectively, from the inside of a lower housing 4 are arranged symmetrically with respect to a point with the center of the lower housing 2 as a reference.例文帳に追加
更に、下部ハウジング4の内側から、電源ON/OFFスイッチ24及び電源コネクタ26とそれぞれ接続する電源スイッチ端子20及び電源コネクタ端子19は、下部ハウジング2の中心を基準として点対称に配置されている。 - 特許庁
The delay amounts of each of combination circuits 13, 14 are measured by setting a second input terminal 19B of a selector switch 19 to selection state, a first input terminal 20A of a selector switch 20 to selection state, and by transitioning the phase of a test clock TCK.例文帳に追加
切替スイッチ19は第2入力端子19Bを選択状態、切替スイッチ20は第1入力端子20Aを選択状態とし、テストクロックTCKの位相を遷移させて、組合せ回路13、14のそれぞれの遅延量を測定する。 - 特許庁
The switch 36 consists of a slide switch and a projection 36a to be its operation part can be operated from the external through an operation hole 46b pierced on the bottom 46b of a recessed part 46a for protecting the terminal Tb1 formed on a terminal board 46.例文帳に追加
このスイッチ36は、スライドスイッチからなり、その操作部である突起36aは、端子台36に形成された端末端子Tb1保護用の凹部46aの底面46bに穿設した操作孔46dを介して、外部から操作できる。 - 特許庁
When the controller detects switching of the actuator switch on the basis of signals of the actuator switch input into the first input terminal and the second input terminal, it determines that the lever is normally rotated to the opening operation position or the closing detection position.例文帳に追加
そして、制御装置は、第1入力端子および第2入力端子に入力されたアクチュエータスイッチの信号に基づいて、アクチュエータスイッチの切り換わりを検知すると、正常にレバーが開動作位置または閉検出位置に回動したと判断する。 - 特許庁
The conversion part has an operational amplifier, a main switch provided between an input terminal and an output terminal of the operational amplifier, multiple feedback capacitors, and feedback switches serially connected to each of the feedback capacitors for connecting a corresponding feedback capacitor to the main switch in parallel.例文帳に追加
変換部は、演算増幅器と、演算増幅器の入出力端子間に設けられたメインスイッチと、複数の帰還コンデンサと、各帰還コンデンサと直列接続され、対応する帰還コンデンサをメインスイッチと並列接続する帰還スイッチと、を備える。 - 特許庁
An output change-over switch 21 is provided between the connection switch 19 and the self-supported output terminal 15, and the generated output can be supplied to the self-supported output terminal 15, from both the system 9 and the generator 1 in the system connection operation.例文帳に追加
連系スイッチ19と自立出力端子15との間に出力切り替えスイッチ21を設け、系統連系運転時は、系統9および発電機1の双方から発電電力を自立出力端子15に供給可能にする。 - 特許庁
A semiconductor device comprises: an external terminal; a calibration circuit that is connected to the external terminal and performs calibration using an external resistive element connected to the external terminal; an internal resistive element; and a switch that is provided between the internal resistive element and the external terminal.例文帳に追加
半導体装置は、外部端子と、外部端子に接続され、当該外部端子に接続される外部抵抗素子を利用してキャリブレーションを行うキャリブレーション回路と、内部抵抗素子と、内部抵抗素子と外部端子との間に設けられたスイッチと、を備える。 - 特許庁
Further, a switch 23i which individually connects a terminal 18i which drives respective scanning line CMj of the organic EL panel 1 and the an electric current terminal for test 25 is provided, an electric current for test is supplied from the electric current terminal 25 and the voltage of the terminal 18j is measured.例文帳に追加
また、有機ELパネル1の各走査線CMjを駆動する端子18jと試験用の電流端子25との間を個別に接続するスイッチ23iを設け、この電流端子25から試験用の電流を流し、端子18jの電圧を測定する。 - 特許庁
Since a shape and a size of the unit switch 1 or an unit case 12 of the terminal unit 8 are set regardless of a case 2 or cover 3 of the switch 1, a required insulation distance can be ensured without increasing a size of a switch main body.例文帳に追加
端子ユニット8のユニット開閉器1やユニットケース12の形状・大きさは開閉器1のケース2やカバー3と関係なく定められるので、開閉器本体を大形化することなく必要な絶縁距離を確保することができる。 - 特許庁
Each of the two communication areas 90, 92 can optionally be validated or invalidated by manual operations of a light receiving power switch and a light transmission power switch of a dip switch configuration built in the terminal 18.例文帳に追加
これら2つの通信エリア90および92のそれぞれは、端末装置18に内蔵されたディップスイッチ構成の受光用電源スイッチおよび送光用電源スイッチの手動操作によって、任意に有効化し、または無効化することができる。 - 特許庁
An I/O terminal is provided with an LED display, an illumination type push button switch (work completion switch lamp) and an LED display (work completion lamp) respectively, and when a line operator pushes the illumination type push button switch, an internal lamp is turned on.例文帳に追加
I/O端末にはLED表示器および照光式押しボタンスイッチ(作業完了スイッチランプ)およびLED表示器(作業完了ランプ)がそれぞれ設けられ、ライン作業者が照光式押しボタンスイッチを押すと、内部のランプが点灯する。 - 特許庁
The analysis part 15 specifies the switch 20 from the determination result determining that the switch 20 is not more distant; and regards the connection port 21 configuring the route 40 of the specified switch 20 as the connection port to which the target terminal 30 is connected.例文帳に追加
解析部15は、判定の結果から、より離れていると判定されなかったスイッチ20を特定し、特定したスイッチ20の経路40を構成している接続ポート21を、対象端末30が接続されている接続ポートとする。 - 特許庁
A switch that is inserted between the power supply terminal and the power line of the respective segments of a memory 100, namely, a switch 1i connected with a segment i is provided with a fuse F1i and transistors T1i and T2i as a semiconductor switch that are provided aside the fuse F1i.例文帳に追加
メモリ100の各セグメントの電源端子と電源ラインの間に挿入されるスイッチ部、例えばセグメントiに接続されるスイッチ部1iは、フューズF1iと、これに併設された半導体スイッチであるトランジスタT1i、T2iを有する。 - 特許庁
The bidirectional battery disconnect switch includes a symmetrical switch MOSFET not accompanied with a short circuit between source/body and a circuit for connecting a body of the MOSFET to a terminal biased to more negative side than of source/drain of the switch MOSFET.例文帳に追加
双方向バッテリ切離しスイッチは、ソース/ボディ間の短絡を伴わない、対称なスイッチMOSFETと、スイッチMOSFETのソース/ドレンの内の、より負の側にバイアスされた端子に、MOSFETのボディを接続するための回路とを含む。 - 特許庁
A transmission packet from an authenticated terminal is transferred to the L3 switch 131 in the job network by the L2 switch 121, thereby enabling the packet to be transferred not only to the authentication network but also to the job network in routing in the job network of the L3 switch 131.例文帳に追加
認証済み端末からの送信パケットは、L2スイッチ121が、業務ネットワークでL3スイッチ131に転送することで、L3スイッチ131の業務ネットワークでのルーティングで、認証ネットワークへも業務ネットワークへも転送可能にする。 - 特許庁
To obtain a structure of a vehicle switch having a contact piece which enables simultaneous soldering of a moving contact plate and a terminal to a board.例文帳に追加
可動接点板と端子を基板に同時に半田付けできる接片を備えた車両用スイッチの構造を提供すること。 - 特許庁
Since the outside of the metal terminal is surrounded with a strong permanent magnet, there is no fear of a switch being turned off even during vibration.例文帳に追加
金属端子の外側は強力な永久磁石で取り巻いてあるので、振動中でもスイッチの切れる心配はない。 - 特許庁
The switch 6 electrically connects selected one of the plurality of input terminals I_1 to I_4 to the output terminal OUT.例文帳に追加
スイッチ6は、複数の入力端子I_1〜I_4のうち選択されたいずれかと出力端子OUTの間を導通させる。 - 特許庁
Thus, the information terminal 1 can easily switch the information distribution destination only by transmitting the switching request RQ.例文帳に追加
したがって、情報端末1は切替要求RQを送信するだけで簡単に情報配信先を切替えることができる。 - 特許庁
Then, a signal, in which an amplitude of the frequency f_0 from an oscillator changes step by step, is entered in the switch output terminal.例文帳に追加
スイッチ出力端子には、発振器からの周波数f_oの振幅が段階的に変化する信号が出力されることになる。 - 特許庁
Unless the power source main source switch (18) is moved to 'off' position and the electric connection with the electric apparatus is stopped, the access to the electric terminal (20) cannot be made.例文帳に追加
電源メインスイッチ(18)を“オフ”位置にし、電気装置への通電を停止しない限り、電気端子(20)にアクセスすることはできない。 - 特許庁
The second switch element group is connected between a third node and a fourth node and the third node is connected to a second input/output terminal.例文帳に追加
第2スイッチ素子群は第3ノードと第4との間に接続され、第3ノードは第2入出力端子に接続される。 - 特許庁
In a receiving unit 20, an operating switch 23 and a terminal part 24 are provided obliquely in an upper portion of a Y-shaped main body 21.例文帳に追加
受信部20において、Y字状に形成された本体21の上部に斜めに操作スイッチ23と端子部24を設ける。 - 特許庁
A power supply input terminal and a bypass capacitor are connected to each other via a current limit resistor and an MOS switch which are inserted in parallel.例文帳に追加
電源入力端子とバイパスコンデンサとを互いに並列に挿入された電流制限抵抗器、MOSスイッチでつなぐ。 - 特許庁
A semiconductor switch driven by a digital controller is arranged between the input to one battery terminal and the outputs.例文帳に追加
1つのバッテリ端子に対する入力と出力との間に、ディジタル・コントローラにより駆動される半導体スイッチが配置される。 - 特許庁
When the authentication is successful, the area network server sets a new main communication key to the communication terminal and a house-side edge switch.例文帳に追加
認証に成功した場合、地域網管理サーバは、新たな主通信鍵を通信端末と宅側エッジスイッチとに設定する。 - 特許庁
To reduce the power consumption of a portable terminal device for which a user can freely set a key to be made to function as a power switch.例文帳に追加
電源スイッチとして機能させるキーをユーザが自由に設定できる携帯端末装置の消費電力を少なくする。 - 特許庁
A feed control circuit 20 has a switch function of connecting either of the feed points 16, 17 to an external connection terminal 21.例文帳に追加
給電制御回路20は、給電点16、17のいずれかを外部接続端子21と接続するスイッチ機能を有する。 - 特許庁
The light control switch 1, formed in a two-piece module size, is equipped with a signal terminal 10 and two pieces of power source terminals 12.例文帳に追加
調光スイッチ1は、2個モジュール寸法に形成され、信号用端子10と、2個の電源用端子12とを有する。 - 特許庁
A switch 12 of the sample hold circuit 20 switches over between conductive and nonconductive depending on voltage of a control input terminal 24.例文帳に追加
サンプルホールド回路20のスイッチ12は、制御入力端子24の電圧に応じて導通と非導通の間で切換わる。 - 特許庁
To provide a changeover switch easy to make wirings for input leads and capable of detecting easily the output terminal on the side connected.例文帳に追加
入力線の配線が容易であり、接続されている側の出力端子を容易に判別できる切換スイッチを提供する。 - 特許庁
A power switch element (Q1) is made to turn on by rising the output voltage of the OUT terminal in a PWM control circuit (8).例文帳に追加
PWM制御回路(8)のOUT端子の出力電圧の立ち上がりによって電力スイッチ素子(Q1)はターンオンする。 - 特許庁
The user terminal decided, in step S44, whether to switch an access network on the basis of this communication medium selection information.例文帳に追加
ユーザ端末では、ステップS44において、この通信メディア選択情報に基づいて、アクセス網を切り替えるか否かを判定する。 - 特許庁
In the OFF period, the short control circuit electrically connects the first node and the output terminal through the short switch circuit.例文帳に追加
OFF期間において、ショート制御回路は、ショートスイッチ回路を介して第1ノードと出力端子との間を電気的に接続する。 - 特許庁
Thus, the battery protection IC 11 of the battery pack 10 does not need a new terminal for communication with the temperature switch IC 12.例文帳に追加
よって、電池パック10の電池保護IC11は、温度スイッチIC12との通信用の新たな端子を必要としない。 - 特許庁
The charging stand 20 includes a switch 230 for setting ON/OFF of a power saving function of the information terminal 10.例文帳に追加
充電台20には、情報端末10の省電機能のON/OFFを設定するためのスイッチ230が設けられている。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|