1016万例文収録!

「地電流データ」に関連した英語例文の一覧と使い方 - Weblio英語例文検索


小窓モード

プレミアム

ログイン
設定

設定

Weblio 辞書 > 英和辞典・和英辞典 > 地電流データに関連した英語例文

セーフサーチ:オン

不適切な検索結果を除外する

不適切な検索結果を除外しない

セーフサーチについて

地電流データの部分一致の例文一覧と使い方

該当件数 : 35



例文

磁気電流法における観測データの処理方法及び装置例文帳に追加

METHOD AND APPARATUS FOR PROCESSING OBSERVATION DATA IN EARTH MAGNETISM EARTH CURRENT METHOD - 特許庁

この間、常にオーガーの積算電流値等の盤掘削データを記録する。例文帳に追加

During this time, ground excavation data such as an integrated current value of an auger are constantly recorded. - 特許庁

データ読出時において、ライトワード線WWLの電圧は接電圧Vssに設定されて、データ読出のための電流経路が形成される。例文帳に追加

In data reading, a voltage of the write word line WWL is set to a ground voltage Vss for forming a current path for data reading. - 特許庁

データ読出時において、ライトワード線WWLの電圧は接電圧Vssに設定されて、データ読出のための電流経路が形成される。例文帳に追加

At the time of read-out of data, voltage of the write-word line WWL is set to ground voltage Vss, and a current path for reading out data is formed. - 特許庁

例文

画像データ用I−V変換回路21は、配線4a及び4bのうち、接電極に接続されている配線に電流を流して、画像データを1対の相補の電流信号に変換して受信する。例文帳に追加

The I-V conversion circuit 21 for image data causes a current to flow to the wire connected to the grounding electrode out of the wires 4a and 4b and converts image data to a pair of complementary current signals to receive them. - 特許庁


例文

これにより、各ブロックは独立した電源電圧および接電圧と接続される電流供給部からのデータ書込電流により選択メモリセルへのデータ書込を実行する。例文帳に追加

Thereby, Each block performs write-in of data for a selected memory cell by the data write-in current from the current supply part connected to the independent power source voltage and the ground voltage. - 特許庁

データ電極駆動回路12は、発光すべき有機EL素子に対応したデータ電極には定電流源の出力側電圧Vcを印加し、残余のデータ電極には接電圧を印加する。例文帳に追加

A data electrode driving circuit 12 applies an output-side voltage Vc of a constant current source to the data electrode corresponding to an organic EL element to emit light and applies the ground voltage to the remaining data electrodes. - 特許庁

データ書込回路51はデータバスDBo,DBeおよび反転データバス/WDBを介して、選択列のビット線BLの他端および電流帰還配線RLの他端を、書込データDINのレベルに応じて、電源電圧Vccおよび接電圧GNDの一方ずつに設定する。例文帳に追加

A data write-in circuit 51 sets the other end of the bit line BL of the selection column and the other end of the current feedback wiring RL to power source voltage Vcc and ground voltage GND respectively in accordance with a level of write-in data DIN through data buses DBo, DBe and an inversion data bus/WDB. - 特許庁

そして、無線通信装置は、この電流設定を維持した状態で、基局201からのデータパケット(“DAT Frame”)を受信する。例文帳に追加

Then, the wireless communication device receives data packets ("DAT Frame") from the base station 201 while maintaining the current setting. - 特許庁

例文

スイッチングトランジスタはセンシングイネーブル信号に応答してデータ入出力ラインと相補データ入出力ラインとの電流を接に流す。例文帳に追加

The switching transistor responds to the sensing enable-signal, and causes current of the data input/output line and the complementary data input/ output line to flow to the ground. - 特許庁

例文

さらに、ローデータ保持電源制御回路150により、メモリセルのローデータ保持電源の電圧を接レベルよりも0.1V程度高い電圧に制御してアクセストランジスタの電流能力を落とす。例文帳に追加

Furthermore, by a low data holding power supply control circuit 150, controlling voltage for low data holding power supply for a memory cell is made higher in a degree of 0.1 V than the ground level, so that a current potential for an access transistor is lowered. - 特許庁

貫通電流遮断手段としてのスイッチ素子129は、電源電圧パッド125から基準電圧発生回路127を介して接電圧パッド126に流れる貫通電流を、データ処理部3の待機時電源電流の検査の際に、遮断する。例文帳に追加

A switch element 129 being a through current cutting-off means cuts off a through current flowing into the ground voltage pad 126 through a reference voltage generating circuit 127 from a power source voltage pad 125 when a power source current at the standby time is tested of the data processing section 3. - 特許庁

この殻変動に伴う電気現象の観測システム3は、送電ケーブル2の一方の陸部分において、金属シース7のシース接線12に電流センサ13を設け、この電流センサ13で検出した電流値を過去のデータと比較して殻変動に伴う異常な電気現象を観測するものである。例文帳に追加

An observation system 3 in the electrical phenomena accompanying the diastrophism provides a current sensor 13 in a sheath grounding conductor 12 of a metal sheath 7 at one land section of a transmission cable 2, and compares a current value detected by the current sensor 13 with past data to observe the abnormal electrical phenomena accompanying the diastrophism. - 特許庁

そこで、ポリシリコンヒューズ抵抗21に電気的に接続されてトリミングする電圧または電流を印加するデータ書き込み端子14を、書き込みデータ読み出し時に接するという回路構成を採用することで小型化を実現した。例文帳に追加

Then miniaturization is realized by adopting circuit constitution in which a data write terminal 14 which is connected electrically to the poly-silicon fuse resistor 21 and to which trimming voltage or current is applied is grounded at the time of reading write data. - 特許庁

そして,データ計測装置20aは,通電電圧Vdc,通電電流Idc,および管対電位Vpeのそれぞれの平均値,最大値およびその計測時刻,ならびに最小値およびその計測時刻を求め,データ読み取りコンピュータ21に与える。例文帳に追加

The data measurement device 20a obtains respective mean values, the maximum values, and the times at which the measurements are performed, for the supply voltage Vdc, the supply current Idc, and the tube-to-ground electrical potential Vpe, obtains the minimum values and the times at which the measurements are performed, and provides them to a data reading computer 21. - 特許庁

前記の柱上変圧器2次側及び低圧線から需要家設備までの負荷に関するデータには、柱上変圧器2次側及び低圧線から需要家設備までの電圧、負荷電流、接電流等の測定値及び測定種別の設定と異常情報を含むことができる。例文帳に追加

The data relating to loads from a secondary side of a pole transformer, low voltage lines and consumer facilities may include measured values, setting information of the measurement types and fault information of voltage, load currents, and ground line currents from the secondary side of a pole transformer, low voltage lines and consumer facilities. - 特許庁

接続制御部110,120は、書込制御回路130,135により制御されて、書込データDINに応じて、一方の書込電流制御線を電源電圧Vccと接続する一方で、他方の書込電流制御線を接電圧GNDと接続する。例文帳に追加

Connection control parts 110, 120 are controlled by write control circuits 130, 135, connect one write current control line to power source voltage Vcc, while connect the other write current control line to ground voltage GND, in accordance with write data DIN. - 特許庁

制御装置15はこの吸収電流信号データを、予め標準試料を用いて求められている試料・接間に流れる電流とコンタクトホールにおける基板のエッチング深さとの関係に照合して、測定対象のホールにおける基板のエッチング深さを検査する。例文帳に追加

A controller 15 checks the absorption current signal data up in a relation between a current flowing between the sample and a ground to be acquired in advance by use of a standard sample and an etching depth of a substrate in the contact hole, and inspects the etching depth of the substrate in a hole to be measured. - 特許庁

さらに、機能ブロック(1ビットDCC回路領域63)に基準電流を供給する基準電流配線65と、諧調デジタルデータ配線68および記憶タイミング信号配線64とが、上下にクロスする箇所では、それらの間に、接電位の配線66Aが挿入されている。例文帳に追加

Wiring 66A having the grounding potential is inserted between reference current wiring 65 for supplying a reference current to functional blocks (one-bit DCC circuit areas 63) and gradation digital data wiring 68 and storage timing signal wiring 64, in positions where they vertically cross. - 特許庁

動力回路と電灯回路に分けて、数多くのフィールドにおけるB種接線の電流に含まれる基本波、第5次及び第7次調波電流を測定し、電路の絶縁抵抗値との関係を実測データを基にして、方程式にまとめ、この方程式をクランプ式漏れ電流計に内蔵したCPUに記憶させることにより、B種接線にクランプするのみで電路の絶縁状態が計測できるようにした。例文帳に追加

Then, the insulation state of the electric line can be measured by only clamping to the class-B ground line. - 特許庁

入力端子1,2に外部からの小振幅データが入力される差動接続されたNMOS13,14のソース電極を共通接続し、電流供給用NMOS11を介して接する。例文帳に追加

Source electrodes of differentially connected NMOSs 13 and 14 with small amplitude data inputted from an external part are connected to input terminals 1 and 2 in common and grounded through an NMOS 11 for current supply. - 特許庁

すなわち、電源電圧および接電圧を供給する電源線の配線長を短くすることができ、これに伴い、電源線の配線抵抗を抑制して、所望のデータ書込電流を供給することができる。例文帳に追加

That is, wiring length of a power source line by which the power source voltage and the ground voltage are supplied is shortened, thereby, wiring resistance of the power source line is suppressed, and desired data write-in current is supplied. - 特許庁

これ応じて、鉄塔側装置10から無線により、時刻情報受信機で取得した時刻情報とともに、事故発生時の電流値を記録したデータをセンタ装置20に送る。例文帳に追加

Time information obtained by a time information receiver and data of ground-wire current values recorded when the accident happened are sent by radio from the steel tower-side device 10 to the center device 20. - 特許庁

本発明は、仮想接メモリアレイにおいてリーク電流の存在に関わらず正確にデータ検出が可能な不揮発性半導体記憶装置を提供することを目的とする。例文帳に追加

To provide a nonvolatile semiconductor storage device capable of correctly detecting data regardless of the existence of a leakage current in a virtual ground memory array. - 特許庁

電流バッファ回路31は、リセット動作に同期してデータ信号ラインL7およびクロック信号ラインL8を強制的に接電位に駆動する。例文帳に追加

A current buffer circuit 31 forcedly drives a data signal line L7 and a clock signal line L8 to a ground voltage synchronously with the reset operation. - 特許庁

データ計測装置20aは,整流器10aへの交流電力の供給の有無を計測するとともに,通電電圧Vdc,通電電流Idc,および管対電位Vpeを所定の時間間隔で計測する。例文帳に追加

A data measurement device 20a measures presence or absence of the supply of AC power to the rectifier 10a, and measures a supply voltage Vdc, a supply current Idc, and a tube-to-ground electrical potential Vpe, at a prescribed time interval. - 特許庁

また、接された基板電位よりデータ読み出し端子の方が高くなり、基板バイアス効果が生じてメモリセルMS1の閾値が上昇し、セル電流が減少して消費電力が低減される。例文帳に追加

Besides, the potential of the data read terminal is made higher than a grounded substrate potential, the threshold value of the memory cell MS1 is increased by generating a substrate bias effect, and power consumption is reduced by decreasing the cell current. - 特許庁

この際、上記第2スイッチは、画素データにおける画面垂直方向での周波数が低い場合には高い場合に比して小なる電流を接ラインに送出する。例文帳に追加

At this time, the second switch sends out to the ground line a current which is smaller than when the frequency of the pixel data in a screen vertical direction is low. - 特許庁

ことで、基準電位17を直接金属シャーシに接することで基準電位の電流経路が短くなり、基準電位が安定し、データドライバ2より放射される妨害電磁波を抑制できる。例文帳に追加

At this time, the current path of the reference potential 17 becomes short by grounding directly the reference potential 17 to the metal chassis and the reference potential becomes constant and the interference electromagnetic waves to be radiated from the data drivers 2 are suppressed. - 特許庁

論理回路およびメモリ回路におけるMOSトランジスタのソース電極線を動作時には接電位に保ち、選択されない待機時には接ソース電極線を接電位より高い電圧に保つことによりデータを破壊することなくMOSトランジスタのゲートトンネルリーク電流を低減する。例文帳に追加

Source electrode lines of MOS transistors in logic and memory circuits are kept at a ground potential in an active mode, and ground source electrode lines are kept at a voltage higher than the ground potential in an unselected standby mode, thereby reducing a gate tunnel leakage current of the MOS transistor without destroying data. - 特許庁

遠隔に存在する検査現場1に設置された制御端末装置10とセンタ2に設置されたサーバ20とがネットワーク3によって接続された渦電流探傷システムであって、制御端末装置10は、この制御端末装置10に接続された、渦電流探傷するための渦電流探傷装置5から得られた探傷データをネットワークを3介してサーバ20に送信し、サーバ20は、ネットワーク3から受信された探傷データを分析して評価を行う、ように構成されている。例文帳に追加

The eddy current flaw detection system comprises a control terminal 10 disposed at a remote inspection site 1 and a server 20 disposed in a center 2 interconnected through a network 3, and the control terminal 10 transmits flaw detection data obtained from an eddy current flaw detector 5 to the server 20 through the network 3 and the server 20 analyzes the flaw data received from the network 3 and evaluates the flaw. - 特許庁

データ書込時には、選択列に対応するビット線ドライバBDVaおよび選択グループに対応するビット線ドライバBDVbが、対応するノードNaおよびNsを、電源電圧Vccおよび接電圧Vssの一方ずつを駆動することによって、選択列のビット線にデータ書込電流が流される。例文帳に追加

At the time of writing data, the bit line driver BDVa corresponding to selected rows and the bit line driver BDVb corresponding to selected groups drive the power supply voltage Vcc and ground voltage Vss of the corresponding nodes Na and Ns one by one, causing a data writing current to flow in the bit lines of selected rows. - 特許庁

出力した電流値や各センサの検出出力はRAM43に記憶され、CPU41は外部のコンピュータ54に対してRAM43に記憶したデータを伝送し、コンピュータ54で遠隔の磁気軸受スピンドル1の運転状況を監視する。例文帳に追加

The outputted current and the detection output of each sensor are stored in a RAM 43, and the CPU 41 transfers the data stored in the RAM 43 to an external computer 54 to monitor the operating state of the magnetic bearing spindle 1 in a remote place by the computer 54. - 特許庁

データ読出時に選択メモリセルRMC♯を通過する第1の電流経路および選択リファレンスセルRMC#を通過する第2の電流経路を形成する配線群のうち、リファレンスセルRMCと異なる方向に沿って配置される配線(接配線GL1,GL2およびビット線BL,/BL)は、低抵抗の金属配線で形成される。例文帳に追加

Out of a wiring group which forms a first current path that passes through the selected memory cell RMC# and a second current path that passes a selected reference cell RMC# upon data reading, wirings (ground wirings GL1 and GL2, and bit lines BL and /BL) arranged along a different direction from a reference cell RMC are formed with metal wirings having low resistance. - 特許庁

例文

携帯端末において、基局と定期的に通信を行う間欠受信区間において、間欠受信区間で動作するPLLを用いてインテリジェンス電池パックと通信を行い、電池残量表示データを取得することによって、クロックによる消費電流の増加を低減させる、携帯端末を提供する。例文帳に追加

The mobile phone terminal uses a PLL operating in an intermittent reception section wherein the mobile phone terminal periodically communicates with a base station, to communicate with the intelligent battery pack and acquires battery residual capacity display data, thereby the increase of current consumption due to a clock is reduced. - 特許庁

索引トップ用語の索引



  
Copyright © Japan Patent office. All Rights Reserved.
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する
英→日 日→英
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する

©2024 GRAS Group, Inc.RSS