| 例文 |
dc sourceの部分一致の例文一覧と使い方
該当件数 : 1976件
Thus, the DC power of the fuel cell power source where the multiple fuel cells with the same ratings are connected in series is converted into a single-phase AC with a prescribed frequency and power.例文帳に追加
これによって複数個の同一定格の燃料電池を直列接続して構成された燃料電池電源の直流電力は、所定の周波数と電力の単相交流に変換される。 - 特許庁
When a pulse current for temperature detection is impressed to a column 2 by a DC electric power source 3, a signal having information as to a voltage of the column 2 is supplied to a timing and temperature controller 4.例文帳に追加
DC電源3が捕集管2に温度検知用のパルス電流を印加すると、捕集管2の電圧についての情報を有する信号が、タイミング及び温度コントローラ4に供給される。 - 特許庁
A high-voltage DC power unit 10 incorporates a high-voltage power source section 12, which generates high-voltage power to be supplied to a load 24 and a CPU 22 which controls the whole unit 10.例文帳に追加
直流高圧電源装置10は、負荷24に供給するための高圧電力を生成する高圧電源部12及び装置全体の動作を司るCPU22を含んで構成されている。 - 特許庁
To meat a demand peculiar to the metal halide lamp, a capacitor 2a for discharge growth is disposed in parallel with a DC power source 1 on the primary side of a transformer 4c to secure discharge growth after dielectric breakdown.例文帳に追加
メタルハライドランプ特有の要求を満たすため、トランス4cの一次側に放電成長用コンデンサ2aを直流電源1と並列に配置し、絶縁破壊後の放電成長を確保する。 - 特許庁
The first DC power source maintains a potential at the input terminal on the positive pole side of the inverter module to be higher than the potential at each output terminal of the U-phase, the V-phase and the W-phase of the inverter module.例文帳に追加
第1直流電源は、インバータモジュールの正極側の入力端子における電位を、インバータモジュールのU相、V相、W相の各出力端子における電位以上に維持する。 - 特許庁
To provide a method for measuring a thrust of a DC linear motor of a magnet movable type in which a measuring accuracy of the thrust is high and troubles are reduced when the motor is used for a drive source of a linear moving unit.例文帳に追加
直線運動部の駆動源に磁石可動型の直流リニアモータを使用する場合に、その推力の測定精度が高く且つトラブルが少ない推力測定方法を提供する。 - 特許庁
Then, when mounting the syringe pump 1 to the mounting parts 31a to 31f, the syringe pump 1 is connected to the AC-DC power source part 41 via the power reception terminal 27 and the power-feeding terminals 35.例文帳に追加
そして、装着部31a〜31fにシリンジポンプ1を装着すると、受電用端子27および給電用端子35を介してシリンジポンプ1がAC−DC電源部41に接続される。 - 特許庁
To reduce a ripple current which flows to a capacitor, in a system which supplies a motor with power, considering a capacitor provided between the positive electrode bus and the negative electrode bus of the inverter as a DC power source.例文帳に追加
インバータの正極母線と負極母線との間に設けられるコンデンサを直流電源とみなして電動機に電力を供給するシステムにおいて、コンデンサに流れるリップル電流を低減する。 - 特許庁
Further, the voltage developed by dividing a source voltage by 3rd and 4th resistors 18 and 20 is supplied to a noninverting input terminal 24 to set the DC level of the counter electrode signal 30.例文帳に追加
また、電源電圧を第3および第4の抵抗18、20により分圧した電圧が非反転入力端子24に供給され、対向電極信号30の直流レベルを設定している。 - 特許庁
In other cases, the current supply by the DC power source 52 is stopped in photographing to turn off the actuator 40 and thus the stop mechanism 42 is held at an L level matching low film speeds.例文帳に追加
それ例外の場合には、撮影時に直流電源52による電流供給を停止してアクチュエータ40をオフ状態とし、絞り機構42を低フィルム感度に適応するLレベルに保持する。 - 特許庁
A charge circuit for charging the capacitor C is formed by connecting the switch Q1 for charge, the capacitor C, and the load 2 between positive and negative electrodes of a DC power source E.例文帳に追加
キャパシタCを充電するための充電回路は、充電用スイッチQ1、キャパシタC、及び負荷2が直流電力源Eの正極と負極との間に接続されることにより形成されている。 - 特許庁
To provide a power supply device and a lighting fixture capable of supplying a stable AC output or DC output which is suitable for a discharge lamp or an LED element as a light source.例文帳に追加
光源としての放電ランプ又はLED素子に対して最適で安定した交流出力又は直流出力を供給することができる電源装置及び照明器具を提供する。 - 特許庁
Input/output signal lines connected to the logic gates of the logical cells driven by power sources of different phases are alternately wired to an integrated circuit in the multiphase DC biased sinusoidal AC power source system.例文帳に追加
多相直流バイアス正弦交流電源系の集積回路に、異なる相の電源で駆動される論理セルの論理ゲートに接続された各入出力信号線を交互に結線する。 - 特許庁
A current flowing to a positive electrode line 51 is branched at a side of a DC power source 80 rather than at the semiconductor breaker 12 so as to prevent the semiconductor breaker 12 from being broken.例文帳に追加
そして、正極線51に流れる電流を半導体遮断器12よりも直流電源80側で分岐させて、コンデンサ14に流入させて半導体遮断器12を破損させないようにしている。 - 特許庁
The external contact is connected to one of a ground signal, an AC signal, and a DC signal to disable the operation of the shunt circuit, to use as a heater, or to use the power source as a stabilizing means.例文帳に追加
外部接点を、接地信号、AC信号、及び、DC信号の1つに結合して、分流器を動作不能としたり、ヒータとして利用したり、電源を安定化手段として用いたりすることもできる。 - 特許庁
Moreover, in case that a power stoppage monitor 11 detects the power stoppage of the commercial power source, this controller supplies, as emergency operation power, the DC voltage discharged from the power battery 8 to the nurse call device 1.例文帳に追加
また、停電監視器11にて商用交流電源の停電が検出された場合には電源バッテリから放電される直流電圧を非常動作電源としてナースコール装置に給電させる。 - 特許庁
A furnace bottom electrode 9 is installed on the bottom wall of the ash melting furnace facing the tip of the plasma electrode 8 and a DC power source 11 for generating an plasma arc 10 is connected between the electrodes 8 and 9.例文帳に追加
プラズマ電極8の先端と対向する灰溶融炉の炉底壁には、炉底電極9を設置し、これらの電極8,9間に、プラズマアーク10発生用の直流電源11を接続している。 - 特許庁
To provide an electrical connection device capable of simultaneously supplying electric power to and charging a number of portable electronic devices of different makers, functions, and types with a single DC voltage source.例文帳に追加
製造元や機能や型式が異なる多数の携帯型電子装置に単一の直流電圧源によって同時に電力供給/充電することが出来る電気的接続装置を提供する。 - 特許庁
An anode 5 is laid at the water bottoms 9 and 10, a cathode 7 is opposed to the anode 5, and the anode 5 and cathode 7 are connected to a DC power source 3.例文帳に追加
水底部9, 10に陽極電極5を敷設し、この陽極電極5に対向させて陰極電極7を配し、陽極電極5と陰極電極7に直流電源3を接続する。 - 特許庁
As a result, even when the output from a power source for the plasma welding is any one the AC voltage, the AC pulse voltage or the DC pulse voltage, penetration of the keyhole of the plasma keyhole welding can be discriminated.例文帳に追加
この結果、プラズマ溶接用電源からの出力が、交流電圧、交流パルス電圧又は直流パルス電圧のいずれの場合でも、プラズマキーホール溶接のキーホールの貫通を判別することができる。 - 特許庁
The laser oscillator 55 is a type to be operated by a DC power supply and has a battery box 53 for storing a battery to be the power source of the laser oscillator 55 at a right side surface of a blade case 33.例文帳に追加
レーザー発振器55は、直流電源によって動作するタイプであって、ブレードケース33の右側面には、レーザー発振器55の電源となる電池を収容する電池ボックス53が設けられている。 - 特許庁
To provide a low cost and compact surface modifying treatment device using a plasma capable of generating high-voltage and high frequency discharge voltage by using a DC power source with relatively low output voltage.例文帳に追加
出力電圧が比較的低い直流電源を用いて高圧・高頻度の放電電圧を発生させることができる、低コストでコンパクトなプラズマによる表面改質処理装置を提供する。 - 特許庁
A similar voltage is applied between a 2nd electrode 11 and a 3rd electrode 13 in the solvent 3 from a DC power source 45, and an ammeter 47 measures the leak current at this moment.例文帳に追加
溶剤3中の第2の電極11と第3の電極13との間にも同様の電圧を、直流電源45により印加し、そのときの漏れ電流を電流計47により計測する。 - 特許庁
To provide a method for driving an electromagnetic actuator which can be speedily operated with the voltage of a DC voltage source or higher without requiring a step-up circuit and a bypass circuit.例文帳に追加
昇圧回路やそのバイパス回路を必要とすることなく、直流電源電圧以上の高い電圧により高速動作させることのできる電磁アクチュエータの駆動方法を提案すること。 - 特許庁
Both electrodes are connected to a DC power source 5, and a 20V voltage is applied between the two electrodes to use the conductive diamond electrode 1 as an anode, and the platinum electrode 2 as a cathode for electrolysis.例文帳に追加
そして、直流電源5に両電極を接続し、導電性ダイヤモンド電極1がアノード、白金電極2がカソードとなるように、両極間に20Vの電圧を付与し、電解を行う。 - 特許庁
The pressure is continuously monitored by the pressure sensor 23, and the control part 33 controls the DC power source 31 to keep the pressure in the sample chamber 3 on the basis of a detection signal of the pressure sensor 23.例文帳に追加
圧力センサー23により圧力の監視を続け、制御部33は圧力センサー23の検出信号に基づいて試料室3内の圧力を維持するように直流電源31を制御する。 - 特許庁
To provide a leak detector for an electric car, which can detect such a state that a capacitor deteriorates and is unable to detect leakage, without dropping the insulation between a DC power source and a car body.例文帳に追加
直流電源と車体との絶縁を低下させることなく、コンデンサが劣化してリーク検出動作ができなくなった状態を検知可能な電気自動車用リーク検出装置を提供する。 - 特許庁
To enable an inverter to operate even in case that the voltage of a DC power source is low by operating a switching element in a group of switching elements over the inverter until the last moment when the on- resistance goes up suddenly.例文帳に追加
インバータの上側スイッチング素子群のスイッチング素子を、オン抵抗が急激に上昇するぎりぎりまで動作させて直流電源の電圧が低い場合でもインバータが動作できるようにする。 - 特許庁
To attain stabilization of power supply by suppressing drop of a power supply voltage to be supplied to an LSI by enlarging a through-rate of a rush current from a DC constant voltage power source just after processing start in the LSI.例文帳に追加
LSIでの処理開始直後における直流定電圧電源からの突入電流のスルーレートを大きくして、LSIに供給される電源電圧の降下を抑え、電源の安定化を図る。 - 特許庁
The non-contact power receiving part produces the DC power source on the basis of the energy fed from the non-contact power supply part 40, and supplies the power necessary for the operation of the tire sensor unit 10.例文帳に追加
この非接触型受電部は、非接触型給電部40から送出されたエネルギに基づいて直流電源を生成し、タイヤセンサユニット10の動作に必要な電力を供給する。 - 特許庁
To provide a changeover circuit for a plurality of DC power sources which can perform the leveling of commercial power source, by controlling the quantity of power supply to the plurality of power sources, and an air conditioner using it.例文帳に追加
複数の電源の電力供給量を制御して、商用電源の平準化を行なうことのできる複数直流電源の切換回路及びそれを用いた空気調和機を提供する。 - 特許庁
In a direct current of a DC power source E, a drive circuit 12 alternately turns on and off electric field effect transistors Q1, Q2 according to a control circuit 15, and an inverter circuit 11 outputs a high frequency to start/light fluorescent lamps FL1, FL2.例文帳に追加
直流電源Eの直流を、制御回路15に従いドライブ回路12は交互に電界効果トランジスタQ1,Q2をオン、オフし、インバータ回路11が高周波出力し、蛍光ランプFL1 ,FL2 を始動、点灯する。 - 特許庁
To provide a power supply unit capable of detecting an abnormal state in a series circuit of a switching element and a discharging resistor connected in between DC power source lines, without causing increase in cost.例文帳に追加
コストの増大を招くことなく、直流電源線間に接続されたスイッチング素子および放電用抵抗の直列回路における異常状態を検出できる電源装置を提供する。 - 特許庁
In the case where the MOSFET 41 (or MOSFET 42) connected to a DC power source 400 (or ground potential) comes to be on, both first and second switching circuits 32 and 33 turn on (or off).例文帳に追加
直流電源400(又は接地電位)に接続されたMOSFET41(又はMOSFET42)がオンした場合は、第1及び第2スイッチング回路32,33が共にオン(又はオフ)する。 - 特許庁
The power converter is composed of a DC voltage source 1, an LC filter circuit 4 consisting of a reactor 2 and a capacitor 3, a damping circuit 7 consisting of a resistor 5 and a semiconductor element 6, and an inverter circuit 8.例文帳に追加
電力変換装置は、直流電圧源1、リアクトル2とコンデンサ3からなるLCフィルタ回路4、抵抗器5と半導体素子6からなるダンピング回路7、及びインバータ回路8で構成される。 - 特許庁
An element region EA is zoned in a lattice shape, and also to each region zoned in the lattice shape, a source cell SC forming the source diffused layer and a drain cell DC forming the drain diffused layer are allocated with regard to a column and a row of the same lattice alternately, respectively.例文帳に追加
素子領域EAが格子状に区画されるとともに、それら格子状に区画された各領域には、同格子の縦列および横列についてそれぞれ交互に、ソース拡散層が形成されるソースセルSCとドレイン拡散層が形成されるドレインセルDCとが割り当てられる。 - 特許庁
A VI converter circuit 32 generates a current 2Ic (Ic is a DC bias current of a charging current Ij) based on the voltage from the voltage source 35, and a VI converter circuit 31 generates a discharging current Id (=2Ic) based on the voltage from the voltage source 35.例文帳に追加
VI変換回路32は、電圧源35からの電圧に基づいて電流2Ic(Icは充電電流Ijの直流バイアス電流)を生成し、VI変換回路31は、同じ電圧源35からの電圧に基づいて放電電流Id(=2Ic)を生成する。 - 特許庁
In this contact type charging device having a charging roller 21 coming into contact with a photoreceptor 20 and a power source circuit 23 for applying DC constant voltage to the roller 21, a power source circuit 23 is equipped with a resistor 24 and applies voltage to the roller 21 via the resistor 24.例文帳に追加
感光体20に接触する帯電ローラ21と、帯電ローラ21に直流定電圧を印加する電源回路23とを有する接触式帯電装置において、電源回路23は抵抗器24を備えており、この抵抗器24を介して帯電ローラ21に電圧を印加する。 - 特許庁
In the time of emergency when the commercial power supply 11 fails, an emergency power supply circuit 25 boosts the DC voltage from the battery 21 to obtain an emergency power source for lighting the LED light source unit 19, and at the same time, supplies the voltage higher than the operating voltage of the microcomputer to the microcomputer 23.例文帳に追加
そして、商用電源11が停電となった非常時には、非常時電源回路25はバッテリ21からの直流電圧を昇圧してLED光源部19の点灯用の非常用電源を得るとともに、マイクロコンピュータ動作電圧より高い電圧をマイクロコンピュータ23に供給する。 - 特許庁
The power source device 1 includes a back converter composed of: a series circuit consisting of a first switching element Q1 and a diode D1, which is connected across the output terminals of a DC power source E; and a series circuit composed of an inductor L1 and a capacitor C1, which is connected across both ends of the diode D1.例文帳に追加
電源装置1は、直流電源Eの出力端間に接続された第1スイッチング素子Q1とダイオードD1との直列回路と、ダイオードD1の両端間に接続されたインダクタL1とコンデンサC1との直列回路とで構成されたバックコンバータを含む。 - 特許庁
The regeneration method for a lead-acid battery has the following steps of: adding a nonionic dispersant to the lead-acid battery; connecting a plus side of a power source with a positive electrode; connecting a minus side of the power source with a negative electrode; applying DC voltage of 20-30 V; and performing dissolving reduction of a lead sulfate film on the surface of the electrode by generating heat between the electrodes.例文帳に追加
鉛蓄電池に非イオン性分散剤を添加し、正極には電源のプラスを、負極には電源のマイナスを接続し、直流電圧を20〜30Vかけ、電極間を発熱させることにより、電極表面の硫酸鉛皮膜を溶解還元する。 - 特許庁
When the impedances of the resistor R1 and the capacitor C2 are sufficiently lower than the impedance to a three-phase AC power source 1, a high-frequency leakage current caused by switching etc. will not return to the three-phase AC power source 1 but will return to the DC link via the capacitor C2 and the resistor R1.例文帳に追加
この抵抗R1とコンデンサC2のインピーダンスが、3相交流電源1へのインピーダンスより十分に低いと、スイッチング等によって生じる高周波漏洩電流は、3相交流電源1には戻らず、コンデンサC2と抵抗R1を介してDCリンクに返る。 - 特許庁
The second loop is constituted of a source ground amplifier in order to keep the voltage of the drain electrode of the PMOS transistor 13 constant by controlling the gate electrode of the PMOS transistor 13 according to an error signal, and the output level of the source ground amplifier is provided with DC offset.例文帳に追加
誤差信号に応じてPMOSトランジスタ13のゲート電極を制御して、PMOSトランジスタ13のドレイン電極の電圧を一定に保持するために、第2のループをソース接地増幅器により構成するとともに、ソース接地増幅器の出力レベルにDCオフセットを持たせている。 - 特許庁
When a power source interruption operation signal which is transmitted from a subscriber terminal 70 is received, a control part 65 of an IDU 60 transfers a power source interruption operation signal to an ODU 40 and also stops power feeding from an AC/DC converter 66 to the respective parts of the IDU 60 and the ODU 40.例文帳に追加
IDU60の制御部65は、加入者端末70から送られてくる電源断操作信号を受信すると、該電源断操作信号をODU40に転送すると共に、AC/DCコンバータ66からIDU60各部及びODU40への給電を停止する。 - 特許庁
In this case, a system control circuit 8 is provided with a means which monitors the output of the power source 7 for backup, and when the output of the charge power source 7 for backup becomes insufficient in standby mode, it changes over a switch 2 so as to output standby power from an AC/DC conversion circuit 3.例文帳に追加
この場合、バックアップ用充電電源7の出力を監視する手段をシステム制御用回路8に設け、待機モード時にバックアップ用充電電源7の出力が不十分になったときには、スイッチ2を切り換えてAC/DC変換回路3から待機電力を出力させる。 - 特許庁
To provide a power supply for an engine electronic controller which prevents a voltage drop at a switching time to a DC power source for backing-up at a generator power supply failure time, and which supplies a stable power without change after switching as a power source for an aircraft engine electronic controller.例文帳に追加
航空エンジン電子制御装置用電源であって、発電機電源故障時、バックアップ用DC電源への切り換え時の電圧降下を防止すると共に、切り換え後の変動のない安定した電源を供給することを特徴とするエンジン電子制御装置用電源を提供する。 - 特許庁
A power unit 9A for supplying AC or DC power to AC loads or various control parts in an automatic vending machine is controlled by a power source control part 9B and the power source control part 9B is connected to a signal line 10 so that data communication with a main control part 1 is enabled.例文帳に追加
自動販売機内の交流負荷や各種制御部へ交流電源や直流電源を供給する電源装置9Aを電源制御部9Bで制御し、かつ、電源制御部9Bを信号ライン10に接続して、主制御部1とデータ通信ができるようにする。 - 特許庁
To provide a power source circuit which can control the connection of an electric double layer capacitor to a DC power supply source in response to the operation/non-operation of a load when the consumption of the current when left unused cannot be ignored and which can alleviate a leakage current depending upon the double layer capacitor.例文帳に追加
放置状態での電池の消耗が無視できないとき、負荷の動作/非動作に応じて直流電源供給源への電気二重層コンデンサの接続制御を可能にし、電気二重層コンデンサに依存するリーク電流を軽減できる電源回路を提供する。 - 特許庁
This drive circuit is equipped with a first light emitting element 11a which is lit continuously by a DC power source 12a, a solar cell 21 which is optically coupled with the first light emitting element 11a, and a photodiode 25 which is optically coupled with the second light emitting element 11b being lit intermittently by the pulse power source 12b.例文帳に追加
直流電源12aにより連続点灯される第1の発光素子11aと、第1の発光素子11aに光結合された太陽電池21と、パルス電源12bにより間欠点灯される第2の発光素子11bに光結合されたフォトダイオード25とを備える。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|