21を含む例文一覧と使い方
該当件数 : 49989件
The head maintenance part 10 is installed on a place off a moving region of the set table 21.例文帳に追加
ヘッドメンテナンス部10はセットテーブル21の移動領域から外れた場所に設置される。 - 特許庁
Both end parts 21 and 22 are joined together via the adhesive, and an endless belt is provided.例文帳に追加
両端部21、22は接着剤を介して継ぎ合わされ、無端状ベルトが得られる。 - 特許庁
Grinding wheels G1 and G2 for grinding the cutter are mounted on a rotary shaft of the motor 21.例文帳に追加
モータ21の回転軸には、刃物を研磨するための砥石G1,G2が装着される。 - 特許庁
This RF sputtering device is a device for applying RF sputtering to a wafer 21.例文帳に追加
本発明に係るRFスパッタ装置は、ウエハ21にRFスパッタ処理を行う装置である。 - 特許庁
The projection 21 projects either the outer side or the inner side of the closed curve CL.例文帳に追加
突起21は閉曲線CLの外側及び内側のいずれかに向けて突出する。 - 特許庁
A leading-out groove 21b is formed on an outer peripheral surface of a small diameter part 21 of a male screw member 2.例文帳に追加
雄ねじ部材2の小径部21の外周面に導出溝21bを形成する。 - 特許庁
The drill mounting frames 23 are set up to a horizontal frame 21 in a freely left-right space adjustable manner.例文帳に追加
ドリル取付けフレーム23は、左右の間隔調整自在に横フレーム21に取付ける。 - 特許庁
The diameter of the inserting hole 11 is formed a little larger than the inserting holes 21.例文帳に追加
挿通孔11の直径を、挿通孔21の直径よりも僅かに大きく形成する。 - 特許庁
An AND circuit 28 resets the T-flip-flop 21 by utilizing the delay signal E.例文帳に追加
論理積回路28は、遅延信号Eを利用してTフリップフロップ21をリセットする。 - 特許庁
When it is determined that new form information cannot be registered in the output device 21 at present, the form information registered in the output device 21 is deleted and then the new form information is registered in the output device 21.例文帳に追加
そして、現時点において新たなフォーム情報の出力装置21への登録が不可であると判断された場合、出力装置21に登録されているフォーム情報が削除された後、新たなフォーム情報を出力装置21に対して登録させる。 - 特許庁
The luminaire for the water tank includes an illumination unit 21 and a control unit 22.例文帳に追加
本発明の水槽用照明装置は、照明ユニット21及びコントロールユニット22を備える。 - 特許庁
The specific gravity of the rod-like member 21 calculated from the size and weight thereof is 0.90.例文帳に追加
寸法及び重さから算出した棒状部材21の比重は0.90となる。 - 特許庁
The branching unit 50 connects the main duct 21 and the plurality of the branching ducts 22 by piping.例文帳に追加
分岐ユニット50は、メインダクト21と複数の分岐ダクト22とを配管接続する。 - 特許庁
The tip of the terminal 1 is inserted in the terminal hole 21 through the terminal insertion hole 31.例文帳に追加
端子1の先端が端子挿通孔31を通して端子孔21に挿入される。 - 特許庁
The controller 21 controls the heater 13 based on a detected temperature of the thermocouple 19.例文帳に追加
コントローラ21は熱電対19の検出温度に基づいてヒータ13を制御する。 - 特許庁
Inside a RAM area 21, encrypted contents A obtained as a result of encryption of contents using a CKey-A are recorded in an areas 21-A, while encrypted contents B obtained as a result of encryption of the contents using a Ckey-B are recorded in an area 21-B.例文帳に追加
また例えば、RAM領域21のうちの、領域21−Aには、CKey-Aを用いてコンテンツが暗号化された結果得られる暗号化コンテンツAが記録され、領域21−Bには、CKey-Bを用いてコンテンツが暗号化された結果得られる暗号化コンテンツBが記録されている。 - 特許庁
The second wiring board 21 is heated and pressed by the heating/pressing tool 40.例文帳に追加
また、第2の配線板21は、加熱・加圧ツール40によって、加熱されると共に加圧される。 - 特許庁
The conductive metallic foils 20, 21 form a ground plane on the combination assembly.例文帳に追加
伝導性金属フォイル20及び21は、グラウンドプレーンを合成アセンブリの上に形成する。 - 特許庁
Accordingly, the first cup seal 21 can be suppressed from being moved in an axial direction.例文帳に追加
したがって、第1カップシール21が軸方向に移動するのを抑制することができる。 - 特許庁
Further, as appropriate, nonwoven fabrics 21 and 23 may be attached onto the surface of the net material 22.例文帳に追加
また、必要に応じて、網材22の表面に不織布21、23を取り付けてもよい。 - 特許庁
The network 21 is a network that a general user's terminal cannot be connected to.例文帳に追加
ネットワーク21は、一般のユーザ端末からは接続することができないネットワークである。 - 特許庁
A conveying roller 22 for conveying the sheet placed on the tray 21 is driven by a motor M1.例文帳に追加
トレイ21に載置されたシートを搬送する搬送ローラ22を、モータM1により駆動する。 - 特許庁
Herein, a connecting means 90 is provided over the front hood 22 and each horizontal hood 21 for connecting the front hood 22 to the horizontal hood 21 with a locking portion 91 provided on one of the front hood 22 and the horizontal hood 21 and an engaging portion 92 provided on the other.例文帳に追加
前ボンネット22と各横ボンネット21とにわたり、前ボンネット22と横ボンネット21の一方に設けた係止部91と他方に設けた係合部92とによって前ボンネット22と横ボンネット21とを連結する連結手段90を設けてある。 - 特許庁
A plurality of axially-elongated ribs 21 and 22 are provided on the inner peripheral surface of a main body 2.例文帳に追加
本体2の内周面に軸方向に延びる複数本のリブ21・22を設ける。 - 特許庁
The main body part 21 has a hollow part 23 in its inside and covers the circumference of the core member 1.例文帳に追加
本体部21は、内部に中空部23を有し、芯部材1の周りを覆っている。 - 特許庁
The bottom and the top of the condenser 6 are fixed to the unit base 14 and the mounting member 21.例文帳に追加
凝縮器6の下部と上部をユニットベース14と取付部材21に固定する。 - 特許庁
An outer side of the light reflecting material film 21 is again coated with an outer insulation film 22.例文帳に追加
光反射材料膜21の外側にはさらに外部絶縁膜22を被膜する。 - 特許庁
Functions of an H.323 gatekeeper are distributed into the master gatekeeper 1 and the proxy gatekeeper 21.例文帳に追加
H.323ゲートキーパの機能を、マスタゲートキーパ1とプロクシゲートキーパ21とにより機能分散する。 - 特許庁
The display device 12 is provided with a metallic bezel 21 provided around the display picture 14.例文帳に追加
表示装置12は、表示画面14の周囲に設けられた金属ベゼル21を備える。 - 特許庁
A shield case 31 covers the electric discharge lamp control circuit 20 without covering the filter circuit 21.例文帳に追加
シールドケース31はフィルタ回路21を覆わず放電灯制御回路20を覆っている。 - 特許庁
A PWM output section 21 drives transistors Q1 and Q2 according to the duty value d.例文帳に追加
PWM出力部21は、デューティ値dに応じてトランジスタQ1、Q2を駆動する。 - 特許庁
The first and second rubber compositions 20, 21 are connected with each other to form a continuous rubber layer.例文帳に追加
第1と第2のゴム組成品20,21は接続されて連続的なゴム層を形成する。 - 特許庁
The cooling structure of a motor generator as a rotary electric machine includes a motor case 21, a stator 50 having a bolt inserting hole 57 formed thereon and housed in the motor case 21, and a bolt 56 inserted into the bolt inserting hole 57 to fasten the stator 50 to the motor case 21.例文帳に追加
回転電機であるモータジェネレータの冷却構造は、モータケース21と、ボルト挿入孔57が形成され、モータケース21に収容されるステータ50と、ボルト挿入孔57に挿入され、ステータ50をモータケース21に締結するボルト56とを備える。 - 特許庁
The defroster 21 is formed by forming a resistance film 23 on a glass plate 22 which is a transparent member.例文帳に追加
デフロスタ21は、透明部材のガラス板22に抵抗膜23を形成したものである。 - 特許庁
While the roller 21 is rotated once (periods A and B), each cleaning bias is consecutively applied.例文帳に追加
転写ローラ21を各々1回転させる間(期間A、B)、各々連続して印加される。 - 特許庁
A capacitor C11 is charged by a current Ia outputed from a constant current circuit 21.例文帳に追加
コンデンサC11は、定電流回路21が出力する電流Iaにより充電される。 - 特許庁
A roof molding 20 is provided with a long-scaled molding main unit 21 and a plurality of clips 30.例文帳に追加
ルーフモール20は、長尺状のモール本体21と複数のクリップ30とを備える。 - 特許庁
Preferably, a subgrade mat 21 is provided between the sound insulating mat 30 and the ballast 20.例文帳に追加
遮音マット30とバラスト20との間には、路盤マット21が設けられているとよい。 - 特許庁
A game board unit 16 comprises a game board 4, a support body 21 and a guide rail frame 22.例文帳に追加
遊技盤ユニット16は、遊技盤4、支持体21及びガイドレール枠22を備える。 - 特許庁
An advertisement 26 different from that of the content is affixed to a cap 23 of the beverage vessel 21.例文帳に追加
また、飲料容器21のキャップ23に内容物とは異なる広告26を付してある。 - 特許庁
Venturi tubes 21 fitted to a partition board 3 fixed in piping so as to penetrate the partition board 3 in the longitudinal direction of the piping, and a closing board which moves forwards and backwards in the longitudinal directions of each venturi tube 21 so as to be able to close the exit side of the venturi tube 21, are provided.例文帳に追加
配管内に固定された仕切り板3を配管長手方向へ貫通するよう仕切り板3に取付けたベンチュリ管21と、ベンチュリ管21の出口側を閉止し得るよう、ベンチュリ管21の長手方向へ進退動可能な閉止板24を設ける。 - 特許庁
The insert and eject mechanism 30 moves a disk inserted into the slot 21 to the loading location.例文帳に追加
挿排機構30は、スロット21に挿入されるディスクを装着位置まで移動させる。 - 特許庁
The peripheral speed of the feed roller 5 is set to the same speed as the peripheral speed of the front roller 21.例文帳に追加
フィードローラ5の周速を、前ローラ21の周速と同様となるように設定する。 - 特許庁
The size of the reaction force of the impact absorbing member 22 differs from the reaction force of the lower absorber 21.例文帳に追加
衝撃吸収部材22の反力の大きさがロアアブソーバ21の反力と異なる。 - 特許庁
The CPU 21 extracts reproduction time of each of the digital data stored in the storage section 25.例文帳に追加
CPU21は、記憶部25に記憶された各デジタルデータの再生時間を抽出する。 - 特許庁
The first plate 21 has an inclined face 21e inclined in the radial direction.例文帳に追加
第1プレート22は、半径方向に対して傾斜する傾斜面21eを有している。 - 特許庁
Air discharged from the blower 11 is let out from the outlet 3 through a chamber 21.例文帳に追加
送風機11から吐出されるエアは、チャンバ21を通じて吹出口3から吹き出される。 - 特許庁
Then, a maintaining section 21 having an insertion hole 21a is monolithically provided to the holding frame 20.例文帳に追加
保持枠20は挿入孔21aを有する保持部21が一体に設けられている。 - 特許庁
The tensile force is applied to the end of the timing belt 21 by a belt tension mechanism of the equipment.例文帳に追加
そして、装置のベルトテンション機構により、張力をタイミングベルト21の端部に加える。 - 特許庁
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|