| 例文 |
variable throttleの部分一致の例文一覧と使い方
該当件数 : 303件
It is determined that a throttle valve reaches the opener regulating opening, when the throttle valve temporarily almost stops before reaching the target throttle opening while the throttle valve is so driven as to stride over the opener regulating opening, and when a code of the value (I controlled variable) of an integral member out of the controlled variables of a drive motor for the throttle valve is reversed.例文帳に追加
スロットルバルブがオープナ規制開度を跨ぐように駆動される期間に、スロットルバルブが目標スロットル開度に到達する前に一時的にほぼ停止して、スロットルバルブの駆動モータの制御量のうちの積分項の値(I制御量)の符号が反転したときに、スロットルバルブがオープナ規制開度に到達したと判断する。 - 特許庁
To provide a variable throttle valve which can prevent the asynchronous phenomenon of the stepping motor for driving a spool in a winter time and cold area and control the opening of a throttle part accurately.例文帳に追加
冬期や寒冷地においてスプール駆動用ステッピングモータの脱調現象を防止し、絞り部の開度を正確に制御できる可変絞り弁を提供する。 - 特許庁
To protect a compressor in defrost operation in a heat pump cycle in which the defrost operation of an evaporator is performed by increasing a throttle opening of a variable throttle mechanism.例文帳に追加
可変絞り機構の絞り開度を増加させることによって蒸発器の除霜運転を行うヒートポンプサイクルにおいて、除霜運転時における圧縮機の保護を図る。 - 特許庁
Further, both throttle values (TH-α) and (TH+α) are calculated with a variable width α corresponding to a transmission ratio at the present time and then the throttle valve is repeatedly and alternatively controlled with the aforesaid two values.例文帳に追加
更に、現時点の変速比に応じた可変幅αで、スロットル値(TH−α)と(TH+α)を演算し、スロットルバルブを該2値で交互繰り返し制御する。 - 特許庁
An engine 1 is equipped with a suction valve variable mechanism 21 for making the working angle of the suction 19 variable, and an actuator 43a for making the opening of a throttle valve 43, provided in a suction passage 40, variable.例文帳に追加
エンジン1は、吸気弁19の作用角を可変にする吸気弁可変機構21と、吸気通路40に設けられたスロットル弁43の開度を可変にするアクチュエータ43aとを備える。 - 特許庁
The spark-ignition internal combustion engine has a variable compression ratio mechanism A in which a machine compression ratio is changeable, a variable valve timing mechanism B in which the valve closing timing of an intake valve is controllable, and a throttle valve 17 in which the throttle opening is changeable.例文帳に追加
火花点火式内燃機関は、機械圧縮比を変更可能な可変圧縮比機構Aと、吸気弁の閉弁時期を制御可能な可変バルブタイミング機構Bと、スロットル開度を変更可能なスロットル弁17とを具備する。 - 特許庁
Second groups 24 of passage grooves consisting of passage grooves to form a variable throttle in connection to a variable throttle valve 3 of car speed responsive type are arranged in two places lying on the second diametric line D2 perpendicularly intersecting the first diametric line D1.例文帳に追加
車速応動型可変絞り弁3に接続する可変絞りを構成する通路溝からなる第2の通路溝群24を、前記第1の直径線D1に直交する第2の直径線D2上の2箇所に配設する。 - 特許庁
To provide a variable throttle valve which can prevent the uncontrollable condition by blocking the displacement of a spool by a fluid force, without giving an influence to the throttle performance, when the flowing sound of the pressure oil at the throttle part is reduced.例文帳に追加
絞り部における圧油の流動音を低減するに場合に、スプールの変位が流体力により阻害されて制御不能になるのを、絞り特性に影響を与えることなく防止できる可変絞り弁を提供する。 - 特許庁
The other end of a return spring 20 with one end thereof connected to the throttle valve 18 is connected to a bracket 28 with the variable position.例文帳に追加
一端をスロットルバルブ18に接続したリターンスプリング20の他端は、位置を可変とするブラケット28へ接続する。 - 特許庁
To prevent an over load state of a compressor while easily and inexpensively achieving the optimal throttle quantity of a capacity variable air conditioner.例文帳に追加
簡便かつ安価に能力可変式空気調和機の適正絞り量を得つつ、圧縮機過負荷状態を回避する。 - 特許庁
A slow-closing valve 27 is a variable throttle valve driven by a slow-closing servo valve 18 as an electric-hydraulic servo valve.例文帳に追加
緩閉鎖弁27を、電気−油圧サーボ弁である緩閉鎖サーボ弁18によって駆動される可変絞り弁とする。 - 特許庁
Here, the prescribed degree of superheat SHTh is a degree of superheat corresponding to a minimum throttle opening (minimum refrigerant flow rate) adjustable by the first variable throttle mechanism 40.例文帳に追加
ここでいう所定の過熱度SHThとは、第1の可変絞り機構40により調整し得る最小の絞り開度(最小冷媒流量)に対応した過熱度のことである。 - 特許庁
In a throttle valve controller 1, a map setting unit 1a sets a variable threshold ε in response to a value of a road surface μ on a map of a preset accelerator opening-throttle opening.例文帳に追加
スロットル弁制御装置1では、マップ設定部1aで、予め設定しておいたアクセル開度−スロットル開度のマップにおいて、路面μの値に応じて可変閾値εを定める。 - 特許庁
At the time of the fuel cutoff, a variable valve train 32, 34 is controlled so that an exhaust gas recirculation amount is increased, and a throttle valve 18 is controlled so that a throttle opening TA is decreased.例文帳に追加
フューエルカット時に、排気ガス再循環量が増えるように可変動弁機構32,34を制御し、かつ、スロットル開度TAが小さくなるようにスロットル弁18を制御する。 - 特許庁
The throttle opening of a variable throttle mechanism 77 provided in an oil passage 72 is reduced or a set value for a hydraulic pressure level detected by a hydraulic sensor 78 provided downstream of the variable throttle mechanism 77 is increased to increase the motive power of an oil circulation pump 74 before starting early post injection.例文帳に追加
オイル通路72に設けられた可変絞り機構77の絞り開度を低下されるか、又は可変絞り機構77の下流側に設けられた油圧センサ78で検出する油圧レベルの設定値を上げることによって、アーリポスト噴射開始時t_1までにオイル循環ポンプ74の動力を増大させる。 - 特許庁
A spark ignition internal combustion engine includes a variable compression ratio mechanism A variable in a mechanical compression ratio, a variable valve timing mechanism B capable of controlling valve close timing of an intake valve 7, and a throttle valve 17 disposed in an engine intake passage.例文帳に追加
機械圧縮比を変更可能な可変圧縮比機構Aと、吸気弁7の閉弁時期を制御可能な可変バルブタイミング機構Bと、機関吸気通路内に配置されたスロットル弁17とを具備する。 - 特許庁
This control device includes a variable throttle valve 3 for changing a flow rate of a hydraulic fluid in a downstream position of a hydraulic motor 13, a control part 41 for controlling the variable throttle valve 3, and a determining part 42 for determining whether or not it is a time for requiring the brake.例文帳に追加
制御装置は、油圧モータ13の下流位置における作動油の流量を変化させる可変式絞り弁3と、可変式絞り弁3を制御する制御部41と、ブレーキ必要時か否かを判断する判断部42と、を備える。 - 特許庁
In the damping force adjusting device, a first flow passage P1 is formed to communicate with both sides of a piston 20 via the fixed throttle valve 50 and the variable throttle valve 40, and a second flow passage P2 is formed to communicate with both the sides of the piston 20 via the fixed throttle valve 50 and the relief valve 60.例文帳に追加
固定絞り弁と可変絞り弁を介してピストン20の両側を連通する第1の流路P1を形成すると共に、固定絞り弁とリリーフ弁を介してピストンの両側を連通する第2の流路P2を形成する。 - 特許庁
In addition to the flow path through a damping force generation means, a short circuit flow path communicating both fluid chambers is provided, and a variable throttle mechanism varying the opening of a throttle part is provided as well as the throttle part 44 in this short circuit flow path.例文帳に追加
一方、減衰力発生手段を経由する流路とは別に、両流体室を連通する短絡流路を設け、この短絡流路には絞り部44を設けるとともに、その絞り部の開度を可変にする可変絞り機構を設ける。 - 特許庁
Consequently, it is possible to speedily move the throttle valve 15 by immediately setting the controlled variable in size to overcome frictional force around an axis of the throttle valve 15 at the point to detect stopping of the throttle valve 15 while the throttle valve 15 is driven and to reduce wasteful time by the frictional force.例文帳に追加
このようにすれば、スロットルバルブ15の駆動中にスロットルバルブ15の停止を検出した時点で、直ちに制御量をスロットルバルブ15の軸回りの摩擦力に打ち勝つ大きさに設定してスロットルバルブ15を速やかに動かすことができ、摩擦力による無駄時間を少なくすることができる。 - 特許庁
A main calculation system 20M and a subsidiary calculation system 20S are used in combination for calculation of a target throttle opening being the same control variable.例文帳に追加
同一の制御量である目標スロットル開度の演算に主演算系20Mと副演算系20Sとを併用する。 - 特許庁
The variable resistance 14 has a characteristic of gradually reducing a resistance value to a fully opening position from an idle position of the throttle valve 20 of the carburetor.例文帳に追加
可変抵抗14は気化器の絞り弁20のアイドル位置から全開位置へ次第に抵抗値が小さくなる特性とする。 - 特許庁
A variable throttle valve and a proportional solenoid type relief value are arranged between a clamping cylinder for driving the clamp claw 340 and an air source.例文帳に追加
クランプ爪340を駆動するクランプ用シリンダとエア源との間に可変絞り弁と比例電磁式リリーフ弁とを設ける。 - 特許庁
Opening variable nozzle vanes 19 and 20 are arranged at an exhaust throttle valve 18 arranged in the exhaust pipe 16 of a diesel engine.例文帳に追加
ディーゼルエンジン11の排気管16に設けた排気絞り弁18には、開度可変のノズルベーン19,20が設置されている。 - 特許庁
A variable throttle valve and a proportional electromagnetic relief valve are provided between a clamping cylinder for driving the clamp claw 340 and an air source.例文帳に追加
クランプ爪340を駆動するクランプ用シリンダとエア源との間に可変絞り弁と比例電磁式リリーフ弁とを設ける。 - 特許庁
In an engine including an electronic control throttle, an intake side variable valve lift mechanism, an intake side variable valve timing mechanism and an exhaust side variable valve timing mechanism, the minimum throttle opening, the lowest valve lift amount, the intake side maximum/minimum valve timing advance angle and the exhaust side maximum valve timing advance value are set according to the engine rotating speed.例文帳に追加
電子制御スロットル,吸気側可変バルブリフト機構,吸気側可変バルブタイミング機構,排気側可変バルブタイミング機構を備えた機関において、機関回転速度に応じて、最小スロットル開度,最低バルブリフト量,吸気側の最大・最小バルブタイミング進角値,排気側の最大バルブタイミング進角値を設定する。 - 特許庁
A variable throttle part 67 whose degree of opening changes in accordance with the vehicle operating conditions is installed in the pressure oil passage leading from the pump 70 to a tank 71 via the throttle part of the second set.例文帳に追加
そのポンプ70から第2の組に属する絞り部を介してタンク71に至る圧油流路に、車両の運転条件に応じて開度が変化する可変絞り部67が設けられる。 - 特許庁
To restrain torque transmitted to a rear wheel from suddenly reducing, when abnormality is caused in control of a throttle valve, in a motorcycle for electronically controlling both the throttle valve and a continuously variable transmission.例文帳に追加
スロットル弁と無段変速機の双方を電子制御する自動二輪車において、スロットル弁の制御において異常が発生した場合に、後輪に伝達されるトルクが急激に低下するのを抑制する。 - 特許庁
To achieve a throttle-less operation and the like by variable control of a closing period of an intake valve in a two cycle internal combustion engine of a relatively simple structure without the need for a scavenging port or a variable valve exhaust system.例文帳に追加
掃気ポートや排気可変動弁機構を必要としない比較的簡素な構造の2サイクル内燃機関でありながら、吸気弁の閉時期の可変制御によるスロットルレス化等を図る。 - 特許庁
To simplify the constitution of a variable intake system and to reduce the number of parts by imparting to a throttle valve a function as a valve for switching a passage in the variable intake system.例文帳に追加
可変吸気システムにおける通路切用換バルブとしての機能をスロットルバルブに持たせることにより、可変吸気システムの構成の簡素化を図ると共に、部品点数の削減を図る。 - 特許庁
Intake air quantity is controlled with combining variable control of lift operation angle of an intake valve 3 by a lift operation angle variable mechanism 51 and opening control of an electronic control throttle valve 18.例文帳に追加
リフト・作動角可変機構51による吸気弁3のリフト作動角の可変制御と、電子制御スロットル弁18の開度制御とを組み合わせて吸気量を制御する。 - 特許庁
A throttle passage 53 bored on the partition wall plate 48 is communicated with a first volume variable chamber 511 in the first bellows 51 and a second volume variable chamber 521 in the second bellows 52.例文帳に追加
区画壁板48に貫設された絞り通路53は、第1ベローズ51内の第1容積可変室511と第2ベローズ52内の第2容積可変室521とに連通している。 - 特許庁
It is provided with variable throttle valves 6, 7 provided on the halfway of each cylinder passage to limit in flow to the flow passage selector valve from the power cylinder and check valves 8, 9 connected to the variable throttle valves in parallel to allow in flow to the power cylinder from the flow passage selector valve.例文帳に追加
各シリンダ通路の途中に設けられてパワーシリンダから流路切換弁への流入を制限する可変絞り弁6、7と、可変絞り弁と並列に接続され流路切換弁からパワーシリンダへの流入を許容するチェック弁8、9とを備えている。 - 特許庁
When the driving current I is larger than the variable B, full closure target throttle opening is gradually corrected to opening side opening, and when the driving current I is not more than the variable B, the full closure target throttle opening is gradually corrected to closing side opening.例文帳に追加
当該駆動電流Iが変数Bより大きい場合には、全閉目標スロットル開度を徐々に開き側の開度に修正し、当該駆動電流Iが変数B以下である場合には、全閉目標スロットル開度を徐々に閉じ側の開度に修正する。 - 特許庁
The ejector cycle includes a variable throttle 80 to make a decompressive expansion to the gas-liquid two phase region upstream of the refrigerant flow of a nozzle 41, and the the degree of opening of the variable throttle 80 is controlled so that the degree of overheat of the refrigerant on the refrigerant outlet side of an evaporator 30 lies within the specified range.例文帳に追加
ノズル41の冷媒流れ上流側に気液二相域まで減圧膨脹させる可変絞り80を設け、蒸発器30の冷媒出口側における冷媒過熱度が所定範囲になるように可変絞り80の絞り開度を制御する。 - 特許庁
A second exhaust port 42 is drawn out from the processing chamber 10, is equipped with a variable throttle 45 and is connected to the flow-regulating valve 60.例文帳に追加
処理室10から第2排気路42を引き出し、可変絞り弁45を設けるとともに流量調整弁60に接続する。 - 特許庁
The controller 40 can adjust the opening by at least the variable throttle 51.例文帳に追加
制御装置40は、温度センサ53の検出温度に基づいて少なくとも可変絞り弁51による絞り開度を調節可能となされている。 - 特許庁
A variable throttle part 44 is provided in the exhaust passage 33 on the inlet side of the turbine wheel 42 and varies the opening area of the exhaust passage 33.例文帳に追加
可変絞り部44は、タービンホイール42の入口側の排気通路33に設けられ、排気通路33の開口面積を変更する。 - 特許庁
The flow regulator 3 is provided with a pressure reducing valve 17 and a variable throttle valve 18 arranged from an inlet side to an outlet side in order.例文帳に追加
その流量調整器3は、入口側から出口側へ順に配置した減圧弁17と可変絞り弁18とを備える。 - 特許庁
A throttle 20 is arranged on the upstream side of an intake pipe, and an intake valve 12 can change an operation characteristic by a variable valve train 22.例文帳に追加
吸気管の上流にスロットル20を設け、吸気バルブ12は可変動弁機構22により動作特性を変更可能とする。 - 特許庁
The steering damper is provided with a variable throttle valve 110 located in the middle of each cylinder passage and limiting inflow to the flow passage switching valve CV from the power cylinder P/C and a check valve 116 connected in parallel to the variable throttle valve 110 and allowing inflow from the flow passage switching valve CV to the power cylinder P/C.例文帳に追加
各シリンダ通路の途中に設けられてパワーシリンダP/Cから流路切換弁CVへの流入を制限する可変絞り弁110と、可変絞り弁110と並列に接続され流路切換弁CVからパワーシリンダP/Cへの流入を許容するチェック弁116とを備えている。 - 特許庁
Opening of variable throttle valves is contracted in the closing direction when the vibration input is detected in accordance with the torque detection signal T by interposing and inserting the variable throttle valves 57a, 57b respectively in discharge side passages 53a, 53b communicated to each of pressure chambers 5a, 5b of a power cylinder 5.例文帳に追加
パワーシリンダ5の各圧力室5a、5bと連通する吐出側連通路53a、53bのそれぞれに、可変絞り弁57a、57bを介挿し、トルク検出信号Tに基づき振動入力が検出されたときには、可変絞り弁57a、57bの開度を閉方向に絞る。 - 特許庁
The deviation Δdin between the equivalent throttle diameter din and a reference throttle diameter din0 corresponding to a controlled variable of the solenoid opening and closing valve in estimating the equivalent throttle diameter is determined, stored and updated (step 125, 130), and the deviation Δdin is reflected on the control of the solenoid opening and closing valve.例文帳に追加
この等価絞り径dinと、等価絞り径推定時の電磁開閉弁の制御量に対応する標準絞り径din0 との偏差Δdinを求め、これを記憶及び更新し(ステップ125,130)、この偏差Δdinを電磁開閉弁の制御に反映する。 - 特許庁
The shutter 4 forms a throttle opening 4a with a variable opening diameter opposed to the insertion port 3a, and closes the insertion port 3a while a portion of the insertion port 3a opposed to the throttle opening 4a is released.例文帳に追加
シャッタ4は、挿入口3aに対向する開口径可変の絞り開口4aを形成し、挿入口3aにおける絞り開口4aとの対向部分を開放した状態で挿入口3aを塞ぐ。 - 特許庁
This intake air flow control device adjusts the intake air flow in a cylinder through execution of cooperation control with variable control over the operating angle VL of an intake valve based on the engine operating condition and variable control over a throttle opening TA.例文帳に追加
この装置は、機関運転条件に基づく吸気バルブの作用角VLの可変制御とスロットル開度TAの可変制御との協働制御の実行を通じて筒内吸気量を調節する。 - 特許庁
According to switching of the three-way valve 13 (switching of the refrigerant passage), the narrowing amount of the refrigerant by the variable throttle 15 is changed.例文帳に追加
前記三方弁14の切り替え(冷媒の流路の切り替え)に応じて,前記可変絞り器15による前記冷媒の絞り量を変更する。 - 特許庁
With this, suitable throttle opening control can be performed even if a valve lift amount is not transmitted from the variable valve control means in communication failure.例文帳に追加
これにより、通信フェイル時に可変動弁制御手段からバルブリフト量が送信されない場合でも適切なスロットル開度制御が行える。 - 特許庁
Flow rate coefficient values of the variable Venturi 13 are obtained for respective moving distances (21 points) of the variable Venturi 13, by switching a throttle valve opening in plural stages (8 stages) within a critical pressure of the variable Venturi 13, then the average value of the flow rate coefficient values for respective moving distances is calculated.例文帳に追加
可変ベンチュリー13の臨界圧以内で絞り弁開度を多段階(8段階)に切り替え、可変ベンチュリー13の各移動距離(21点)において可変ベンチュリーの流量係数値を求め、各移動距離における流量係数値の平均値を求める。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|