| 意味 | 例文 |
output- currentの部分一致の例文一覧と使い方
該当件数 : 10397件
In the differential amplifying circuit, when an amplification start signal EN is input, amplifying operation is started, difference of differential output signals OUT 0 and OUT 1 is amplified at high speed and without malfunction by turning on the current addition transistor after lapse of a delay time decided by delay DLY for example.例文帳に追加
差動増幅回路は、増幅開始信号ENが入力されると増幅動作を開始し、例えばさらに遅延DLYで決まる遅延時間経過後に、電流加算トランジスタがオンすることで、差動出力信号OUT0、OUT1の電圧レベルの差を高速かつ誤動作なく増幅する。 - 特許庁
To provide a separator unit in which, by using a current collector made of a porous body, flooding does not occur even if bending portions are provided in the gas passage in the fuel cell, and which has a high cooling capacity and can increase output of the fuel cell.例文帳に追加
多孔(こう)体から成る集電体を使用することによって、燃料電池内におけるガスの流路に屈曲箇所を設けてもフラッディングが発生することがなく、発電効率が高く、冷却能力が高く、燃料電池の出力を高めることができるようにする。 - 特許庁
Then, by varying a voltage VG of a variable voltage source 143, the magnitude relation between an output voltage VREF of a voltage source 144 and the voltage VG is controlled so as to vary a ratio of currents supplied from current mirror circuits 138, 139 to a differential circuit 137 respectively.例文帳に追加
そして、可変電圧源143の電圧V_Gを可変して、この電圧V_Gと電圧源144の出力電圧V_REFとの大小関係を制御することにより、カレントミラー回路138,139より差動回路137にそれぞれ流れる電流の比を可変する。 - 特許庁
The switching vector SV determined on the basis of a current deviation and a vector determination table is selected as an output switching vector SVo, and a holding time TK set in accordance with a torque and a rotational speed of the motor is obtained to start a timer for clocking (S210 to S230).例文帳に追加
電流偏差とベクトル決定テーブルとに基づいて決定されたスイッチングベクトルSVを、出力スイッチングベクトルSVoとして選択すると共に、電動機のトルクや回転速度に応じて設定される保持時間TKを取得し、計時用のタイマーをスタートさせる(S210〜S230)。 - 特許庁
A diode 4 changes a route through which the detection current flows so as to allow a potential relation between the connection of a positive side and a negative side corresponding to a cell 2 to be inverted if a disconnection occurs, and an inversion detection circuit 5 detects an inversion in the potential relation to output a disconnection detection signal.例文帳に追加
そして、ダイオード4は、断線が発生すると、対応するセル2の正側,負側接続線間の電位関係を反転させるように検出用電流が流れる経路を変化させ、反転検出回路5はその電位関係の反転を検出して断線検出信号を出力する。 - 特許庁
This light receiving circuit is provided with a photodiode PD, a biasing means for making the bias voltage of the photodiode PD zero volt, a FET2 for detecting the cathode voltage of the photodiode PD, and an operational amplifier OP1 for converting current through the photodiode PD into voltage on the basis of the output of the FET.例文帳に追加
フォトダイオードPDと、前記フォトダイオードPDのバイアス電圧を零ボルトとするバイアス手段と、前記フォトダイオードPDのカソード電圧を検出するFET2と、前記FETの出力に基づき前記フォトダイオードPDを流れる電流を電圧に変換するオペアンプOP1とを具備する。 - 特許庁
The control circuit 3 computes a time To, according to the following equation, using each value Tn and Zn in the memory and the input voltage Vi and the output current Io being detected, and switches a transistor q1 from ON to OFF at the point of time when the time To has passed from the ON time of the transistor Q1.例文帳に追加
制御回路3は、メモリの各値Tn,Znと検出した入力電圧Viおよび出力電流Ioとを用いて、下記式に従って時間Toを算出し、トランジスタQ1のオン時点から時間Toが経過した時点で、トランジスタQ1をオンからオフに切り替える。 - 特許庁
When the engine operation point used for power generation shifts to the high output side due to the change of demanded power generation, it is determined whether the shift of engine operation point should be assisted, depending on the positional relationship between the current engine operation point and the target optimum engine operation point to be shifted.例文帳に追加
要求発電量が変化したことにより発電に用いるエンジン動作点が高出力側へ移行した場合、現在のエンジン動作点と移行すべき目標最適エンジン動作点との位置関係に応じてエンジン動作点の移行をアシストするか否かを判断する。 - 特許庁
The alternating voltage signal generated between the terminals of the detection part is inputted into a synchronous detection part 33 through a filter part 31 and an alternating-current amplification part 32, and the output of a clock generation part 35 for generating a clock synchronized with the excitation wave of the oscillation part 34 is synchronously detected and amplified as a reference signal.例文帳に追加
検出部の端子間に発生した交流電圧信号を濾波部31,交流増幅部32を介し同期検波部33に入力し,発振部34の励振波に同期したクロックを発生させるクロック発生部35の出力を参照信号として同期検波,増幅する。 - 特許庁
Then, when a lighting signal XDATA 2 is made active (L), a select signal SEL 2 is made H after a time T3, and then, an output voltage V1 of a current-to-voltage conversion circuit 12-1 becomes low, and after a time T4, a sample hold signal SH2 is made L.例文帳に追加
次いで点灯信号XDATA2をアクティブ(L)にし、次いで時間T3が経過するとセレクト信号SEL2をHにし、次いで電流−電圧変換回路12−1の出力電圧V1がローになり、次いで時間T4が経過するとサンプルホールド信号SH2をLにする。 - 特許庁
A control circuit 30 controls the output of the DC power supply 10, so that it does not go into a state where it sells its power to the commercial power supply 1, based on the information from the current sensor 31 and 32, when the change-over switch selects the DC power supply 10.例文帳に追加
制御回路30は、切替スイッチ20が直流電力供給装置10を選択している状況において、電流センサ31,32からの情報に基づき、商用電源1への売電状況とならないように、直流電力供給装置10の出力を制御する。 - 特許庁
Thus, an ON-DUTY of a rectangular-wave voltage outputted from the rectangular-wave-voltage generating part 20 is increased or decreased and an effective value of a high-frequency power source voltage of the inverter circuit part 3 is changed and an amount of the output current of the inverter circuit part 3 is controlled.例文帳に追加
このように矩形波電圧発生部20から出力する矩形波電圧のON−DUTYを増加または減少させることによりインバータ回路部3の高周波電源電圧の実効値を変化させ、インバータ回路部3の出力電流の大きさを制御する。 - 特許庁
A visual effect setting part 25 sets visual effect for making switching from the current screen display to a next screen display appear to be smooth based on the attribute relation and visual effect history information to output state switching control information to a three- dimensional space visualization part 13.例文帳に追加
ビジュアルエフェクト設定部25は、属性関係とビジュアルエフェクト履歴情報をもとに現在の画面表示から次の画面表示への切り替えをスムーズに見せるためのビジュアルエフェクトを設定し、状態転換制御情報を三次元空間視覚化部13に出力する。 - 特許庁
The PWM circuit 26 generates a discharge detection pulse every time the filtered discharge current detection signal exceeds a threshold value, detects generation frequency of discharge from generation frequency of the discharge detection pulse, and changes output voltage of a DC/DC converter 18 depending on the generation frequency of discharge.例文帳に追加
このPWM回路26は、フィルタ後の放電電流検出信号がしきい値を越える毎に放電検出パルスを発生し、この放電検出パルスの発生頻度から放電の発生頻度を検出し、その発生頻度に応じてDC/DCコンバータ18の出力電圧を変化させる。 - 特許庁
Since the temperature of the resistor 15 is approximately proportional to a temperature resistance value, the temperature of the portion of the rotor 2 near the bearing is calculated by detecting using the ammeter 16 a current flowing through the primary coil 11, and converting the output of the ammeter 16 into a temperature using a temperature calculation means 17.例文帳に追加
抵抗器15の温度と温度抵抗値とは略比例関係にあるので、1次コイル11を流れる電流を電流計16で検出し、その出力を温度算出手段17により温度に変換して、回転体2の軸受近傍部位の温度を算出する。 - 特許庁
The ASIC A1 controls: respective regulators C1 to C5: start, standby and restoration; high impedance to an output part of an I/O interface in a connected I/O device; and through current prevention in a part including the input of the I/O interface.例文帳に追加
ASIC A1は、レギュレータC1、C2、C4、C5を制御し、起動、待機、復帰の制御を行うと共に、接続されている入出力装置の入出力インタフェースの出力部に対するハイインピーダンス制御を行い、入出力インタフェースの入力を含む部分における貫通電流防止制御を行う。 - 特許庁
To provide a rotating electrical machine which is inexpensive and can be reduced in size, while securing its insulation performance and improves its cooling by effectively radiating the heat generated in a stator coil, and markedly improves its rated output, by enabling larger current application to the allowable temperature of the stator coil.例文帳に追加
安価で、絶縁性能を確保しながら、小型化でき、固定子コイルにおいて発生した熱を効果的に放熱して、冷却効果を向上し、固定子コイルの許容温度に対してより大きな通電を可能として、定格出力を格段に向上する回転電機を提供する。 - 特許庁
To solve the problem that a semiconductor device, especially, a semiconductor device using a thin film transistor has variance in potential to be output or value of a current flowing to the thin film transistor owing to variance in threshold of the thin film transistor even when a constant signal is input.例文帳に追加
半導体装置、特に薄膜トランジスタを用いて形成された半導体装置においては、一定の信号を入力したとしても、薄膜トランジスタのしきい値ばらつき等に起因して、出力される電位や、薄膜トランジスタを流れる電流値にばらつきを生じてしまう。 - 特許庁
While a current broadcast program received from a broadcast reception section 1 is recorded into a storage device 3 via an input output control section 2, the recorded information is read and decoded by a reproduction section 4b and an image pattern display section 6 displays the video image via a smooth change-over control section 5.例文帳に追加
放送受信部1から受信した現在の放送を記憶装置3に入出力制御部2を介して録画をしながら録画済みの情報を読出して再生部4bでデコードし、その映像をスムーズ切換え制御部5を介して画面表示部6に表示する。 - 特許庁
When a control current S1 supplied to first to fourth detection switches 44A to 44D has become inactive (an "L" level), the first to fourth detection switches 44A to 44D all become nonconducting, so that an output voltage of each battery 20 is blocked off by a detection switch 44.例文帳に追加
第1乃至第4検出スイッチ44A乃至44Dに供給される制御信号S1が非アクティブ(「L」レベル)になると、第1乃至第4検出スイッチ44A乃至44Dの全てが非導通となり、各電池20の出力電圧が検出スイッチ44で遮断される。 - 特許庁
In a determination voltage generation circuit 1, a current mirror circuit is constituted of transistors Q3-Q7, and a voltage VT1 independent of the supply voltage VCC is generated between both ends of a resistor R1, and an output voltage V- which is a reference voltage is acquired from a connection point between the transistor Q7 and a resistance R7.例文帳に追加
判定用電圧生成回路1において、トランジスタQ3〜Q7でカレントミラー回路を構成し、抵抗R1の両端に、電源電圧VCCに依存しない電圧VT1を発生させて、トランジスタQ7と抵抗R7との接続点から、基準電圧となる出力電圧V−を得る。 - 特許庁
To provide a power amplifier circuit provided with a plurality of amplifiers each being supplied with a power supply voltage via a fuse and each amplifying power of an input signal, which avoids occurrence of an undesirable fuse blowout in the fuse by a current equivalent to the total sum of output currents of the amplifiers.例文帳に追加
電源電圧がヒューズを通じて供給されて入力信号についての電力増幅を行う複数の増幅部を備えたもとにおいて、各増幅部の出力電流の総和に相当する電流をヒューズに不所望な溶断を生じさせないものとする。 - 特許庁
To provide a connection structure of a boosting circuit to a battery eliminating voltage drop due to wiring resistance and large current at operation of the boosting circuit by disusing wiring from the battery to the boosting circuit, and as a result, drastically improving breadth of the increase of the boosting circuit output voltage.例文帳に追加
バッテリから昇圧回路までの配線を不要にして、昇圧回路の動作時の配線抵抗及び大電流による電圧ドロップを解消し、この結果、昇圧回路の出力電圧上昇幅を大幅に改善できる昇圧回路のバッテリへの接続構造を提供する。 - 特許庁
To provide a manufacturing method of a membrane electrode assembly for a solid polymer fuel cell, with high durability and capable of obtaining high output voltage in wide-ranged current density, and having high durability even with use under a circumstance in which drying or wetting are repeated.例文帳に追加
耐久性が高く広範囲な電流密度において高い出力電圧が得られ、乾燥や湿潤が繰り返されるような環境下で使用しても高い耐久性を有する固体高分子形燃料電池用膜電極接合体の製造方法を提供する。 - 特許庁
This device 1 has a sensor casing 2, having a gas inflow opening 21 and a gas outflow opening 23, a limiting current type oxygen sensor unit 3 installed therein, a signal processing circuit 5 for processing the output signal and for outputting the oxygen concentration information, and a display device 7.例文帳に追加
酸素濃度検出装置1は、ガス流入口21及びガス流出口23を有するセンサケース2と、この中に設置された限界電流式酸素センサユニット3と、その出力信号を処理して酸素濃度情報を出力する信号処理回路5及び表示装置7を有する。 - 特許庁
To supply stable voltage without output voltage fluctuating even if it stops the operation of any regulators, and also to improve power efficiency, in a current share type switching power unit consisting of a plurality of regulators each of which has an error amplifier and a hysteresis comparator.例文帳に追加
誤差アンプとヒステリシス・コンパレータを有する複数のレギュレータからなるカレントシェア型のスイッチング電源装置において、一部のレギュレータの動作を停止させても出力電圧が変動することがなく安定な電圧を供給するとともに、電力効率を向上させることができるようにする。 - 特許庁
To provide a small-sized high-frequency output device of a high-frequency cosmetic device which outputs the high-frequency current with the same high voltage of the conventional ones using the approximate one third of the supply voltage of the conventional ones to reduce the electricity consumption and can miniaturize the components or the like.例文帳に追加
従来の約3分の1の供給電圧で、従来と同様な高圧の高周波電流を出力させ、消費電力の低減を図ると共に、部品類の小型化も可能となる高周波美容器における小型高周波電流出力器を提供する。 - 特許庁
When an input voltage Vi rises, a gate voltage VQ_1G of an MOS transistor Q1 is increased, the base current of a transistor Q3 flows, the transistor Q3 is turned into active state, a capacitor C is charged with electric charges, an output voltage Vo rises and a stable state is provided on the condition of Vi=Vo.例文帳に追加
入力電圧Viが立ち上がると、MOSトランジスタQ1のゲート電圧V_Q1G が上昇し、トランジスタQ3のベース電流が流れ、トランジスタQ3が動作状態に入り、コンデンサCに電荷が充電され、出力電圧Voが立ち上がり、Vi=Voとなったところで安定状態となる。 - 特許庁
The solar battery 4 is irradiated with the light from a multi-wavelength LED light emitter 2 to measure the absolute spectral sensitivity (A/W) of the solar battery, from the irradiated light intensity (W) of each wavelength from the light emitter 2 and the output the short-circuit current (A) of the solar battery 4 of each wavelength.例文帳に追加
多波長のLED発光部2からの光を太陽電池4に照射し、多波長LED発光部2からの各波長毎の照射光強度(W)と各波長毎の太陽電池4の出力短絡電流(A)とから、太陽電池の絶対分光感度(A/W)を測定する。 - 特許庁
Then a low voltage is applied to the ionization chamber 12, by switching a normally-used high-voltage source 30 to a low-voltage power source 32 using a switch mechanism 34 of a power unit 14 and the voltage signal obtained, by converting the output current has its value recorded by a counting arithmetic part 18.例文帳に追加
次に電源ユニット14のスイッチ機構34により通常使用する高電圧電源30から低電圧電源32に切り換えて電離箱12に低電圧を印加し、出力電流が変換された電圧信号を計数演算部18によりその値を記録する。 - 特許庁
A shunt resistance 30 to be used for measuring an output current in a unidirectional power source part 1 is arranged on a substrate 32 along the air course of cooling air flowing on the substrate 32, namely arranged approximately in line with a diode bridge 101 and a switching element, as shown in Fig. 2.例文帳に追加
単方向電源部1の出力電流を測定するために用いるシャント抵抗30は、前記基板32上を流れる冷却風の風路に沿って該基板32上に配置されるとともに前記ダイオードブリッジ及び前記スイッチング素子と略同一直線状に配置される。 - 特許庁
The occurrence of the unintended electrical path between the load and reference potential causes a change in the voltage or current signal on the first power conductor of sufficient magnitude relative to the threshold value for detection by the detector such that the output signal of the detector is indicative of a detected fault.例文帳に追加
負荷と基準電位との間の偶発的な電気路の発生によって、検出器による検出の該閾値に対して十分な大きさで第1の電力導体の電圧或いは電流信号が変化し、検出器の出力信号は検出された故障を示す。 - 特許庁
An optical receiving circuit 10 according to an embodiment includes: light receiving means 12 for outputting a current according to input light; an inverting amplifier 13 having an input terminal connected with the light receiving means; and a feedback circuit 14 connected between input and output terminals of the inverting amplifier 13.例文帳に追加
本発明の実施形態にかかる光受信回路10は、入力光に応じて電流を出力する受光手段12と、入力端子に前記受光手段が接続された反転増幅器13と、反転増幅器13の入出力間に接続された帰還回路14を具備する。 - 特許庁
The preamplification circuit for converting a current signal into a voltage signal comprises an amplification circuit 2, a feedback resistor 3 for connecting the input terminal to the output terminal of the amplifier circuit 2 and a gain switching circuit 10 for switching the resistance of the feedback resistor 3.例文帳に追加
本発明の前置増幅回路は、電流信号を電圧信号に変換する前置増幅回路において、増幅回路2と、この増幅回路2の入力端子と出力端子を接続する帰還抵抗3と、この帰還抵抗3の抵抗値を切り替える利得切替回路10を有する。 - 特許庁
This controller gets a first reactor current command by computing the difference between the output voltage command Vo^* of the DC-DC converter and the voltage value Vo detected with a voltage sensor 5 by means of a subtractor 21, and multiplying the computed voltage difference by a control constant Kpm in a control block 22.例文帳に追加
DC−DCコンバータの出力電圧指令値Vo^*と、電圧センサ5で検出される電圧値Voとの差を減算器21によって算出し、算出した電圧差に対して、制御ブロック22において制御定数Kpmを乗ずることにより、第1のリアクトル電流指令値を求める。 - 特許庁
A low-pass filter 10 includes a RC filter circuit 12, a differential operation circuit 14 which subtracts an output signal OUT from a low frequency component of an input signal IN and outputs a differential signal DF, a RC filter circuit 16, a voltage-current conversion circuit 18, and a capacitor 20.例文帳に追加
ローパスフィルタ10は、RCフィルタ回路12と、入力信号INの低周波成分から出力信号OUTを減算して差分信号DFを出力する差分演算回路14と、RCフィルタ回路16と、電圧電流変換回路18と、コンデンサ20とを備える。 - 特許庁
Then, the maximum power consumption Pmax can be supplied to the AC/DC power conversion part 31 by supplying electric power from the electric storage part 32 even if AC/DC power conversion part 31 can output only the same direct current power Pdc_ave as the average power consumption Pave.例文帳に追加
したがって、AC/DC電力変換部31が、平均消費電力Paveと同じ直流電力Pdc_aveしか出力することができなくても、蓄電部32から電力を供給することによって、AC/DC電力変換部31に最大消費電力Pmaxを供給することができる。 - 特許庁
Since command injection quantity during idling can be estimated to be calculated as roughly fixed value, a microcomputer determines that abnormal output of the rail pressure sensor 7 occurs when a current value of the command injection quantity during idling is calculated as a value clearly different from values calculated in a past.例文帳に追加
アイドル時指令噴射量は、略一定の値に算出されると予測できるので、マイコンは、アイドル時指令噴射量について現在値が過去値に比べて明らかに異なる値に算出された場合に、レール圧センサ7に出力異常が発生したものと判断する。 - 特許庁
By means of a detection part 5 connected to the CPU 2, amplification information such as an output voltage of a power source in the power amplification part provided in the main operation part 3, an electric current consumption, and a heat temperature of a power semiconductor element is detected so that data are taken into the CPU 2 and displayed on the LCD monitor 4.例文帳に追加
CPU2には検出部5が接続され、主動作部3の有するパワーアンプ部の電源の出力電圧、消費電流、パワー半導体素子の発熱温度等のアンプ情報を検出してCPU2にデータ取り込みを行ってLCDモニタ4に表示する機能を有している。 - 特許庁
In a charge/discharge circuit shown in Fig. 1, as a switch 2 is closed and an output side switch 3 is opened, a current is applied to a capacitor 6, a diode 9, a capacitor 7, a diode 10, and a capacitor 8 which are connected in series with each other via a resistor 4 and the capacitors 6-8 are charged.例文帳に追加
図1の充放電回路において、充電時には、スイッチ2が閉じられ、出力側のスイッチ3が開かれるので、抵抗4を介して、直列に接続されているコンデンサ6、ダイオード9、コンデンサ7、ダイオード10、およびコンデンサ8に電流が流れ、コンデンサ6乃至コンデンサ8が充電される。 - 特許庁
Thereby, a lithium-ion battery 20 can be charged with an output voltage Vout containing a pulsating flow of appropriate magnitude, and a smoothing capacitor 15C can be used which has smaller capacitance than that in the conventional cases where charging is carried out with a constant voltage and a constant current.例文帳に追加
これにより、適切な大きさの脈流を含んだ出力電圧Voutによるリチウムイオン電池20への充電が可能となり、従来のように定電圧かつ定電流によって充電を行う場合と比べ、容量の小さな平滑コンデンサ15Cを使用することが可能となる。 - 特許庁
When the output voltage drops at overload, the oscillation frequency and the maximum current value of the switching element become small, due to the clamp voltage varying circuit 13, but the rate of change is adjusted to be optimum from the outside a semiconductor device for switching power control by the clamp voltage regulating circuit 60.例文帳に追加
過負荷時に出力電圧が低下すると、クランプ電圧可変回路13により、発振周波数とスイッチング素子の最大電流値が小さくなるが、その変化率をクランプ電圧調整回路60によりスイッチング電源制御用半導体装置の外部から最適に調整する。 - 特許庁
To provide a fuel cell with the output voltage and current density enhanced by forming a composite polymer film structured thin, having a high strength and causing less cross-leak amount of the fuel gas and using this composite polymer film as a solid polymer electrolyte film for the fuel cell.例文帳に追加
薄膜化が可能で、強度が高く、かつ燃料ガスのクロスリーク量が少ない複合ポリマー膜を提供し、この複合ポリマー膜を固体高分子電解質膜として用いることによって、出力電圧および電流密度が向上された燃料電池を提供する。 - 特許庁
When either of motors 12 and 14 is driven substantially at its maximum output and the other of the motors 12 and 14 is controlled into stop state or power generation state, the current passed through a shared bus bar 26 is equal to or less than the maximum value of the capacity (A) of a bus bar 22 and the capacity (A) of a bus bar 24.例文帳に追加
電動機12,14の一方が略最大出力で駆動され、電動機12,14の他方が停止状態または発電状態に制御される場合は、共有バスバー26を流れる電流がバスバー22の容量(A)とバスバー24の容量(A)の最大値以下となる。 - 特許庁
The clamp circuit 18 that matches an output of a gain control amplifier 4 corresponding to a period for a black reference signal with a prescribed reference value is provided with a voltage current conversion circuit 36 as a gain control means to control a gain of a clamp signal supplied to the gain control amplifier 4.例文帳に追加
黒基準信号の期間に対応するゲインコントロールアンプ4の出力値を所定の基準値に一致させるクランプ回路18に、ゲインコントロールアンプ4に供給されるクランプ信号のゲインを制御するゲイン制御手段としての電圧電流変換回路36を設けた。 - 特許庁
The control of the output of the high voltage generating circuit 3 in this way simplifies the circuit structure or the like and the response time is made faster compared to the case like in a conventional example that the supply quantity of the liquid (water ) to the discharge current 1 is controlled.例文帳に追加
しかも、特許文献1に記載されている従来例のように放電電流1への液体(水)の供給量を制御する場合に比較して、上述のように高電圧発生回路3の出力を制御する方が回路構成等が簡単であり且つ応答時間を早くできる。 - 特許庁
The AC motor control device also corrects the operation of the current adjusting part 11 so that the output from the reactive component current operation part 10 coincides with the command value I_γ^* of a pseudo reactive component current from the reference value setting part 5.例文帳に追加
無効分電流演算部10の出力I_γと基準値設定部5の疑似無効分電流指令値I_γ^*との差から誤差量に基づいた演算をする電流調節部11と、電流調節部11からの出力で補正し、補正された値を用いて二軸成分電圧のうち一方の軸成分の電圧の大きさを調節する第1のゲイン調節部71とを含み、無効分電流演算部10からの出力が前記基準値設定部5からの疑似無効分電流の指令値I_γ^*と一致するように前記電流調節部11の演算を補正する交流電動機制御装置を提供する。 - 特許庁
The generator 1 for vehicles includes a field winding 4 that magnetizes a field pole of a rotor, a stator having stator windings 2, 3 as polyphase windings, multiple rectifier modules 5X and so on respectively provided in correspondence with the multiple output terminals of the stator windings 2, 3, a generation controller 7 that controls an excitation current passed through the field winding 4 to control output voltage.例文帳に追加
車両用発電機1は、回転子の界磁極を磁化させる界磁巻線4と、多相巻線としての固定子巻線2、3を有する固定子と、固定子巻線2、3の複数の出力端子のそれぞれに対応して設けられる複数の整流器モジュール5X等と、界磁巻線4に流れる励磁電流を制御することにより出力電圧を制御する発電制御装置7とを備えている。 - 特許庁
When the drive devices 100A, 100B, and 100C are not allowed to be operated simultaneously by current limitation, it is determined whether drive control data of two drive devices of the drive devices 100A, 100B and 100C are output or not, and output of the drive control data of the drive device not outputting the drive control data is inhibited or permitted based on a determination result.例文帳に追加
駆動装置100A,100B,100Cについて、電流制限により同時に動作することができない場合に、駆動装置100A,100B,100Cのうち何れか2つの駆動装置の駆動制御データが出力中であるか否かを判別し、その判別結果に基づいて、駆動制御データの出力が行われていない駆動装置の駆動制御データの出力を禁止又は許容する。 - 特許庁
To provide: a negative electrode plate for a nonaqueous electrolyte secondary battery including an electrode active material layer and having high output-input characteristics; a method for manufacturing a negative electrode plate having a negative active material layer formed by suitably bonding negative active material particles to the surface of a current collector without using a resin binder; a nonaqueous electrolyte secondary battery having high output-input characteristics; and a battery pack.例文帳に追加
電極活物質層を備える高出入力特性の非水電解液二次電池用負極板を提供し、また樹脂製結着材を用いずとも、集電体表面に良好に負極活物質粒子を固着させて電極活物質層を形成してなる負極板を製造する方法を提供し、これによって高出入力特性の優れた非水電解液二次電池、および電池パックを提供する。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|