| 例文 |
torque commandの部分一致の例文一覧と使い方
該当件数 : 1185件
The calculating part 72 calculates an engine torque command value cTE from cTDR and an actual variable speed ratio aRATIO.例文帳に追加
算出部72はcTDRおよび実変速比aRATIOより、エンジントルク指令値cTEを算出する。 - 特許庁
Then, basic command torque corresponding to the crank angle position of the engine 11 is corrected with the cylinder pressure change coefficients to calculate final command torque, and the torque of a MG12 is controlled like feed-forward to generate the command torque, so that the revolution of the engine 11 is stopped at the target stop position.例文帳に追加
そして、エンジン11のクランク角位置に応じた基本指令トルクを筒内圧変化係数で補正して最終的な指令トルクを求め、この指令トルクを発生するようにMG12のトルクをフィードフォワード的に制御することで、エンジン11の回転を目標停止位置で停止させる。 - 特許庁
The torque limit section 56 sets a reduction rate of a torque command value T^*48 according to an element temperature of each switching element in the rotary electric machine 20 to perform processing for reducing the torque command value T^*48.例文帳に追加
そして、トルク制限部56は、回転電機20のスイッチング素子の素子温度に応じてトルク指令値T^*48の低減レートを設定してトルク指令値T^*48を低減させる処理を行う。 - 特許庁
With the car 8 moved to the uppermost floor, the torque command value detection device 14 detects a torque command value Tm_2, and outputs this value to the load compensating torque gain computing device 15.例文帳に追加
そして、乗りかご8を最上階に移動させた状態で、トルク指令値検出装置14はトルク指令値Tm_2を検出し、この値を荷重補償トルクゲイン演算装置15に出力する。 - 特許庁
A saturation circuit 7 corrects the torque command value T_1 so that, when r denotes a length of a moment arm and U_1 denotes a stiffness command value, the torque command value T_1 satisfies a relation of |T_1|≤U_1×r and outputs it.例文帳に追加
飽和回路7は、モーメントアームの長さrと、剛性指令値U_1としたとき、トルク指令値T_1が|T_1|≦U_1×rの範囲に制限されるように、トルク指令値T_1を補正して出力する。 - 特許庁
A slip rotation command value (a feedback command value) is calculated on the basis of a deviation between an actual slip rotating speed and a target value, and target torque-converter torque is calculated from the slip rotation command value and slip rotation gain.例文帳に追加
実際のスリップ回転速度と目標値との偏差に基づき、スリップ回転指令値(フィードバック指令値)を算出し、該スリップ回転指令値とスリップ回転ゲインから目標トルクコンバータトルクを算出する。 - 特許庁
This method is characterized in that when a voltage command Vd* 35, Vq* 36 exceeds a limit value of a voltage value limiter 37, a torque command T* 24 is added or subtracted by a torque command adding and subtracting means 50.例文帳に追加
この発明では、電圧指令Vd^*35、Vq^*36が電圧値リミッタ37の制限値を超えたときに、トルク指令加減手段50によってトルク指令T^*24を加減する点が特徴である。 - 特許庁
A multiplier 404 calculates torque Tm*_3 of after torque boost prohibition determination by Tm*_2×K_bst, an adder 405 calculates torque command value Tm*' after response improvement compensation by Tm*+Tm*_3.例文帳に追加
乗算器404は、Tm*_2×K_bstによりトルクブースト禁止判定後トルクTm*_3を算出し、加算器405は、Tm*+Tm*_3により、レスポンス向上補償後・トルク指令値Tm*'を算出する。 - 特許庁
While, a detecting steering torque T is fed back, and an addition angle α is generated so that the detecting steering torque T is approached to command steering torque T*.例文帳に追加
一方、検出操舵トルクTがフィードバックされ、指示操舵トルクT^*に検出操舵トルクTを近づけるように、加算角αが生成される。 - 特許庁
This makes a value, where the two phase-d current command values I DMAX and I DMIN are inserted, into a phase-d current command I DCMD, according to the magnitude of the torque command TCMD.例文帳に追加
トルク指令TCMDの大きさに応じて上記2つのd相電流指令値IDMAX、IDMINを内挿した値をd相電流指令IDCMDとする。 - 特許庁
A tape is previously formed from the torque command and the voltage limiting value, and the id command and the iq command are calculated without repeating calculation.例文帳に追加
トルク指令と電圧制限値から予めテーブルを作成しておき、id指令とiq指令を繰り返し計算なしに算定する構成とする。 - 特許庁
In this way, it calculates a torque command value for maintaining DC voltage at a command value, and performs the control of maintaining the DC voltage at the command value.例文帳に追加
このように、直流電圧を指令値に維持するためのトルク指令値を算出し、これを指令値として直流電圧を指令値に維持する制御を行う。 - 特許庁
This on/off-control periodically generates a regeneration torque and a drive torque equal to or larger than zero so that the average torque in a prescribed period corresponds to the torque command Te*.例文帳に追加
このオンオフ制御は、所定期間内の平均トルクがトルク指令Te*と対応するように、回生制動トルクと、ゼロ以上の駆動トルクとを周期的に発生させる制御である。 - 特許庁
If the instruction torque Tind is minute because the operation quantity has just reached the torque control section E, the maximum value selecting section 63 selects the holding torque T0 and outputs it as command torque Tcom.例文帳に追加
操作量がトルク制御区間Eに達したばかりで指示トルクTindが微小であれば、最大値選択部63は、保持トルクT0を選択し、指令トルクTcomとして出力する。 - 特許庁
Engine torque for travelling obtained by the power generation engine torque calculation section and a travelling engine torque calculation section 23 is added and given to an engine torque command value calculation section 25, thus commanding toque to an engine 1.例文帳に追加
発電分エンジントルクと走行分エンジントルク演算部23で求められた走行分エンジントルクを加算し、エンジントルク指令値演算部25に与えてトルク等をエンジン1に指令する。 - 特許庁
When the command to determine the home position is issued, the torque of the motor is switched to a torque required to determine the home position after a starting torque greater than the torque required to determine the home position is detected.例文帳に追加
前記原点出し指令時には前記モータのトルクは原点出しに必要なトルクよりも大きい始動トルクが検出されてから前記原点出しに必要なトルクに切り替えられる。 - 特許庁
Torque applied to a steering shaft is detected to obtain a primary torque command value securing robust stability by H∞ control.例文帳に追加
ステアリングシヤフトにかかるトルクを検出して、H∞制御によりロバスト安定性を確保した一次トクル指令値を求める。 - 特許庁
A motor torque command value is calculated, on the basis of the estimated gear efficiency, the torque of the axle shaft and the gear ratio (step 106).例文帳に追加
そして、推定したギヤ効率、アクスルシャフトのトルク及びギヤ比に基づきモータトルク指令値を算出する(ステップ106)。 - 特許庁
Next, in a holding period T2, the command value torque is changed by the maximum value of change rate of the first post-dulling torque y1.例文帳に追加
次に、保持期間T2では、第1なまし後トルクy1の変化率の最大値により指令値トルクが変化する。 - 特許庁
The load compensating torque gain computing device 15 calculates a load compensating torque gain Gw based on the load value Wn and torque command values Tm_1, Tm_2, and sets the load compensating torque gain Gw in a load compensating torque gain setting device 10.例文帳に追加
荷重補償トルクゲイン演算装置15は、この荷重値Wn、トルク指令値Tm_1およびTm_2をもとに荷重補償トルクゲインGwを計算し、この値を荷重補償トルクゲイン設定装置10に設定する。 - 特許庁
A control unit 16 gets a target torque command, based on an operation command, the rotational speed of the motor 22, etc.例文帳に追加
コントロールユニット16は、運転操作指令、モータ22の回転速度等に基づいて、目標とするトルク指令値を求める。 - 特許庁
When the torque command Tt overlapping a dead-band region is corrected to the outside of the dead-band region, each torque command Tt_FL-Tt_RR is corrected to sustain the difference ([Tt_FL+Tt_RL]-[Tt_FR+Tt_RR]) of the torque command Tt to the left wheel and the right wheel.例文帳に追加
また、不感帯の領域に重なったトルク指令Ttを、不感帯の領域外に補正する際、左輪及び右輪へのトルク指令Ttの差分(〔Tt_FL+Tt_RL〕−〔Tt_FR+Tt_RR〕)を維持するように、各トルク指令Tt_FL〜Tt_RRを補正する。 - 特許庁
The driving force distribution device 12 is provided with a first current-command-value operation unit 67 for calculating a current command-value I* based on a torque command value T*, and a displacement-command-value operation unit 68 for calculating a displacement-command value D*.例文帳に追加
駆動力配分装置12は、トルク指令値T*に基づいた電流指令値I*を算出する第1の電流指令値演算部67及び変位指令値D*を算出する変位指令値演算部68を備えた。 - 特許庁
An inverter 1_1 generates a d-axis voltage command and a q-axis voltage command from a torque command T_1^*, and supplies electric power to an induction motor 2_1 in response to the d-axis voltage command and the q-axis voltage command.例文帳に追加
本発明においてインバータ1_1は、トルク指令T_1^*からd軸電圧指令、q軸電圧指令を生成し、そのd軸電圧指令、q軸電圧指令に応答して誘導モータ2_1に電力を供給する。 - 特許庁
This drive controller sets a current command value to a transient upper limit current larger than a stationary upper limit current via a current command value operation part 102, which orders a current to be supplied to a motor 100 when increasing a torque command value of torque requested for a motor 100 from a torque command 101 to a transient upper limit torque larger than the stationary upper limit torque.例文帳に追加
トルク指令部101から指令されるモータ100に要求するトルクのトルク指令値を定常上限トルクよりも大きな過渡上限トルクに増大させる場合に、モータ100に供給する電流を指令する電流指令値演算部102で電流指令値を定常上限電流よりも大きな過渡上限電流に設定することを特徴とする。 - 特許庁
The thermal model 15 outputs a second torque command 13 based upon the power deviation 18 and/or power consumption a limit of a calculated time later, and the second torque command 13 is input to a second subtracter 12, which performs subtraction between the first torque command 11 and second torque command 13 and outputs the result to a generator-side converter 2 to perform torque control over an aerogenerator 1.例文帳に追加
熱モデル15は、算出された時間の時限後に、電力偏差18及び又は消費電力に基づいて第2のトルク指令13を出力し、この第2のトルク指令13を第2の減算器12に入力し、第1のトルク指令11と第2のトルク指令13とを減算し、その結果を発電機側コンバータ2に出力して風力発電機1におけるトルク制御を実施する。 - 特許庁
A torque ripple elimination control computer 19 computes a torque ripple compensation value for restraining torque ripple of the permanent magnetic synchronous motor 3 based on the torque current command value and the primary frequency angle obtained from the speed control system 6 and outputs the torque current command value including the compensation value to a current control system 8.例文帳に追加
トルクリプル除去制御演算器19は、速度制御系6からのトルク電流指令値および一次周波数角に基づいて永久磁石同期電動機3のトルクリプルを抑制するためのトルクリプル補償値を演算しトルク電流指令値に加味して電流制御系に出力する。 - 特許庁
Thus, the motor car 20 changes the torque command Tm2* from the motor MG2 by using the motor MG3.例文帳に追加
このように、モータMG3を利用してモータMG2のトルク指令を変更する。 - 特許庁
A motor torque command section 20b calculates a motor torque command value depending on the acceleration signal and delivers it to an inverter 14 thus driving a motor 9 and a travel unit 11.例文帳に追加
モータトルク指令部20bはアクセル信号に応じてモータトルク指令値を算出し、インバータ14へ出力することで電動機9を駆動し走行装置11を駆動する。 - 特許庁
Moreover, the filtering section 12 is equipped with a limiter operation determination section 122, which determines whether a basic torque command T^*[Nm] and a limited torque command T'[Nm] are different or not.例文帳に追加
また、フィルタ処理部12は、基本トルク指令値T^*[Nm]と制限後トルク指令値T’[Nm]が異なるか否か判定するリミッタ作動判定部122を備える。 - 特許庁
On the other hand, the internal combustion engine is controlled so as to output the target engine torque at this instance by adding torque equivalent to the command of the power generation to it, based on the command of the output increase.例文帳に追加
一方、内燃機関は、出力増大指令に基づき、このときの目標機関トルクに発電指令相当のトルクを増して出力するように、制御する。 - 特許庁
The motor controller 109 determines a change rate of the first torque command and the second torque command corresponding to an input/output responding performance of the step-up/down converter 201.例文帳に追加
モータコントローラ109は、昇降圧コンバータ201の入出力応答性能に応じて、第1のトルク指令および第2のトルク指令の変化率を決定する。 - 特許庁
Provided is a controller 126 which outputs the limited torque command T'[Nm] or the filtered torque command T"[Nm], based on the results of the limiter operation determination section 122.例文帳に追加
リミッタ作動判定部122の判定結果に基づいて、制限後トルク指令値T’[Nm]またはフィルタ後トルク指令値T”[Nm]を出力する制御部126を備える。 - 特許庁
The milling state in the interior of the dryer roll 2 is determined on the basis of the speed command value, a torque command value in the driving controller 5, and the mechanical loss torque.例文帳に追加
そして、上記速度指令値、駆動制御装置5におけるトルク指令値、及び上記メカロストルクに基づいて、ドライヤロール2の内部のリミング状態を判定する。 - 特許庁
The primary delay filter 54 outputs a torque command TR, by eliminating the frequency components generated in the basic torque command TRb by the fluctuations of the motor revolution MRN.例文帳に追加
1次遅れフィルタ54は、モータ回転数MRNの変動によって基本トルク指令値TRbに生じる周波数成分を除去して、トルク指令値TRを出力する。 - 特許庁
If the torque command value is below zero when the accelerator pedal is off, the torque command value is limited to zero or below while the accelerator pedal is off (steps S107-S110).例文帳に追加
アクセルペダルがオフにされた際に、トルク指令値が0以下であるとき、アクセルペダルがオフである間、トルク指令値を0以下の値に制限する(ステップS107〜S110)。 - 特許庁
The drive controller for electric vehicles includes torque command means 23 which outputs motor command torque Tr corresponding to accelerator opening, and an inverter device 22.例文帳に追加
アクセル開度に応じたモータ指令トルクTrを出力するトルク指令手段23と、インバータ装置22とを有する電気自動車の駆動制御装置に適用する。 - 特許庁
A current command value calculation part 31 calculates the assist current command value I on the basis of the steering torque Th, target steering torque Th*, and the current Im of a motor 6.例文帳に追加
電流指令値演算部31は、操舵トルクTh、目標操舵トルクTh*、及びモータ6のモータ電流Imとに基づいてアシスト電流指令値Iを演算する。 - 特許庁
Then a command for generating the vibration suppression torque is transmitted at the decided timing.例文帳に追加
そして、決定された時期に振動抑制トルクを発生させる指令を発信する。 - 特許庁
When a current command value for a PDU 3 is set as the torque command value of a motor 1, feedback operating units 14a and 14b compare phase currents being fed to the motor 1 with the current command value and calculate a voltage command value for driving the motor 1 according to the torque command value.例文帳に追加
モータ1のトルク指令値としてPDU3に対する電流指令値が設定されると、フィードバック演算器14a、14bがモータ1へ供給される相電流と電流指令値とを比較して、トルク指令値通りにモータ1が駆動するように電圧指令値を算出する。 - 特許庁
Then the transmission input torque limiting means, in a hybrid travel mode, makes the requesting torque to the engine 1 held in a larger value out of the engine torque command value when the target drive torque changes from the negative torque to the positive torque and the engine combustion lower limit torque, and corrects the difference with the prescribed value (gear backash stuffing torque) by a motor generator 5.例文帳に追加
そして、変速機入力トルク制限手段は、ハイブリッド走行モードの場合は、エンジン1への要求トルクを目標駆動トルクが負トルクから正トルクに切り変わる際のエンジントルク指令値とエンジン燃焼下限トルクの大きい方の値に保持させて、前記所定値(ギヤガタ詰めトルク)との差分をモータジェネレータ5で補正する。 - 特許庁
As a result, the method slowly changes the torque command Tm2^* even when the motor torque Tm2tmp1 rapidly changes, it may suppress a torque shock of a ring gear shaft 32a caused by a sudden change of the motor torque command Tm2^* from a motor MG2.例文帳に追加
この結果、仮モータトルクTm2tmp1が急変してもモータトルク指令Tm2*をゆっくり変化させるから、モータMG2のトルク指令Tm2*が急変することにより生じるリングギヤ軸32aのトルクショックを抑制することができる。 - 特許庁
When the motor torque command value is to be limited, the motor torque command value is limited, based on the allowable upper limit torque line shown with a solid line, instead of the outputable upper limit torque line, shown by a wavy line under motor revolution acceleration at which abnormal voltage increase is generated.例文帳に追加
モータトルク指令値を制限するに際し、異常電圧上昇を生ずるモータ回転加速度のもとでは、波線図示の出力可能上限トルク線に代えて、実線で示す許容上限トルク線を基にモータトルク指令値の制限を行う。 - 特許庁
This steering control device is provided with an assist control means for setting a turning command value to impart assist torque according to the steering torque and driving a turning actuator based on the turning command value, and a turning command value correction means for setting a turning angle command value so that the steering torque in relation to a steering angle may be a prescribed range and correcting the turning command value based on the turning angle command value.例文帳に追加
操舵トルクに応じたアシストトルクを付与するように転舵指令値を設定し、転舵指令値に基づいて転舵アクチュエータを駆動するアシスト制御手段と、操舵角に対する操舵トルクが所定範囲となるように転舵角指令値を設定し、転舵指令値を転舵角指令値に基づいて補正する転舵指令値補正手段とを設けた。 - 特許庁
With the acquired vibration torque made difference torque t_mp (S304, S307), an EPS motor current command value I_c is corrected on the basis of the difference torque t_mp, and a corrected EPS motor current command value I_ca is calculated (S309).例文帳に追加
取得された振動トルクを差分トルクt_mpとし(S304、S307)、EPSモータ電流指令値I_cを差分トルクt_mpに基づいて補正し、補正EPSモータ電流指令値I_caを算出する(S309)。 - 特許庁
While a car 8 is moved to the lowermost floor with no load inside the car 8, a torque command value detection device 14 detects a torque command value Tm_1, and outputs this value to a load compensating torque gain computing device 15.例文帳に追加
乗りかご8内を無負荷状態とした上で最下階に移動させた状態で、トルク指令値検出装置14はトルク指令値Tm_1を検出し、この値を荷重補償トルクゲイン演算装置15に出力する。 - 特許庁
A motor controller 20 regenerates energy from the motor to the motor-drive battery, on the basis of this corrected torque command, controls the output torque of the motor and drives the wheels, on the basis of a torque command computed separately.例文帳に追加
モータ制御装置20は、この補正されたトルク指令値に基づきモータからモータ駆動用バッテリへエネルギを回生し、また別途演算されたトルク指令値に基づき、モータの出力トルクを制御して車輪を駆動する。 - 特許庁
A limiter 35 that has a characteristic of Gm(s)/Gp(s) controls torque to the torque command value outputted from an adder 34 and then outputs the torque command value to a control block 11 denoting the motor 5 and a control block 31.例文帳に追加
Gm(s)/Gp(s)なる特性を有するリミッタ35は、加算器34から出力されるトルク指令値に対して、トルク制限を行い、モータ5を示す制御ブロック11および制御ブロック31に出力する。 - 特許庁
A torque command correcting means is provided, and when the phase current of a brushless motor detected by a current detection means is larger than a preset value, an amount of a torque command decided by a torque control means is decreased.例文帳に追加
トルク指令補正手段を設け、電流検出手段により検出されたブラシレスモータの相電流が予め設定された値より大きい場合、トルク制御手段で決定したトルク指令量を減少する。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|