| 意味 | 例文 |
Torque sensorの部分一致の例文一覧と使い方
該当件数 : 1600件
By referring an assist map preliminarily prepared in a memory unit 42, a CPU 41 determines a command current value which corresponds to the steering torque and the car speed respectively detected by a steering torque sensor 21 and a speed sensor 22 to control the rotation of the electric motor 14.例文帳に追加
CPU41は、メモリ装置42に予め用意されたアシストマップを参照することにより、操舵トルクセンサ21及び車速センサ22によりそれぞれ検出された操舵トルク及び車速に対応した指令電流値を決定して、電動モータ14の回転を制御する。 - 特許庁
Also, the 2nd displacement sensor 220 measures the vibration amplitude of radial (radius) direction of the mobile part 201 and the 1st driving gear 214 causes displaced up and down a permanent magnet 215 as a driver producing suck repulsion power and changes the torque that is measured by a torque sensor 213.例文帳に追加
また、第2の変位センサ220は、可動部201のラジアル(半径)方向の振動振幅を計測し、第1の駆動装置214は、吸引反発力を発生する駆動子としての永久磁石215を上下に変位させ、トルクセンサ213で計測されるトルクを変化させる。 - 特許庁
Further a power steering ECU 22 is installed to compute the steering assisting amount on the basis of the steering torque and steering angle detected by the torque sensor 20 and steering angle sensor 19, respectively, and the intersecting angles αand β between the main shaft 12 and an intermediate shaft 14 and between it 14 and an extension shaft 16.例文帳に追加
そして、さらに、トルクセンサ20と舵角センサ19が検出する操舵トルクと操舵角およびメインシャフト12と中間シャフト14および中間シャフト14とエクステンションシャフト16の間の交差角α、βに基づいて操舵アシスト量を演算するパワーステアリングECU22を設けた。 - 特許庁
To protect an electric motor while simplifying a vehicle body component and reducing the weight in a power steering device for a vehicle equipped with a torque sensor, the electric motor activated according to the detection value of the torque sensor, and a transmission mechanism transmitting a rotational power of the electric motor to a steering wheel side.例文帳に追加
トルクセンサと、該トルクセンサの検出値に応じて作動する電動モータと、操舵輪側に電動モータの回転動力を伝達する伝動機構とを備える車両のパワーステアリング装置において、車体構成部材を簡素化して重量軽減を図りつつ、電動モータの保護を可能とする。 - 特許庁
The controller 53 inputs the signal of a pressure sensor 52 which is used to detect supercharging pressure, excites the electromagnetic proportional pressure reducing valve 54, after the supercharging pressure lowers below p1 and during the period until it rises to P2, reduces the limited value of pump input torque to T1, smaller than rated torque T0, to carry out reduced torque control.例文帳に追加
コントローラ54は過給圧を検出する圧力センサ52の信号を入力し、過給圧がP1以下になった後、P2まで上昇するまでの間、電磁比例減圧弁54を励磁し、ポンプ入力トルクの制限値を定格トルクT0より小さいT1に減らし、減トルク制御を行う。 - 特許庁
The controller detects the torque working to the rotation axis 213 by the torque sensor 214 when the robot 20 is rotated around the axis 213 while the door 11 is held by the robot 20, and stops rotating the robot 20 when the detected torque is a predetermined value or larger.例文帳に追加
制御装置は、双腕ロボット20によりドア11を把持した状態で、この双腕ロボット20を旋回軸213で旋回させる際、トルクセンサ214により旋回軸213に作用するトルクを検出し、この検出したトルクが所定値以上である場合には、双腕ロボット20の旋回を停止する。 - 特許庁
In the magnetostrictive torque sensor of an electric power steering system, a demagnetization means M2 can supply an AC current to coils 40A, 40B and demagnetizes the rotary shaft so as to prevent torque detection accuracy from degradation, even if the magnetization of the rotary shaft may reduce the torque detection accuracy.例文帳に追加
電動パワーステアリング装置の磁歪式トルクセンサの回転軸が磁化するとトルク検出精度が低下するが、消磁手段M2でコイル40A,40Bに交流電流を供給して回転軸を消磁することでトルク検出精度の低下を防止することができる。 - 特許庁
When an abnormality determination part 22 determines occurrence of abnormality in a torque sensor 5 or a signal transmitting system thereof, a target electric current value setting part 21 sets a target electric current value based on a steering torque value maintained in a steering torque storage part 23 before occurrence of the abnormality.例文帳に追加
異常判定部22が、トルクセンサ5またはその信号伝送系における異常が発生したと判定すると、目標電流値設定部21は、その異常が生じるより前に操舵トルク記憶部23に保持された操舵トルク値に基づいて目標電流値を設定する。 - 特許庁
The humanoid robot calculates a joint position track correction value and a joint torque correction value from a measurement value of a sensor, corrects a joint position track and a joint torque using the calculated correction values, and drives a motor provided on a joint by the corrected joint torque.例文帳に追加
人間型ロボットは、センサの測定値で関節位置軌跡補正値と関節トルク補正値をそれぞれ計算し、計算された各補正値を用いて関節位置軌跡と関節トルクを補正し、補正された関節トルクによって関節に設置されたモータを駆動することができる。 - 特許庁
The power steering device includes: a control device for generating assist torque 10 for assisting the steering torque of a driver; and a resonance frequency band removal means 40 for removing the mechanical resonance frequency component of a composition different form a spring resonance system that is built in a torque sensor 23.例文帳に追加
電動パワーステアリング装置は、運転者の操舵トルクを補助するアシストトルク10を発生させる制御装置と、トルクセンサ23に内蔵されるバネ共振系とは異なる構成物の機械共振周波数成分を除去し得る共振周波数帯除去手段40を備えている。 - 特許庁
One steering torque signal output from a steering torque sensor 21 and passed through a LPF 31 is respectively converted by two A/D converters 33, 34, and the steering signals are taken out at two times from the two A/D converters in one computation cycle to obtain four steering torque signals.例文帳に追加
操舵トルクセンサ21からの出力されLPF31を通った1つの操舵トルク信号を2個のA/D変換器33,34にてそれぞれ変換すると共に、1演算サイクル内に2つのA/D変換器33,34から操舵トルク信号を2回ずつ取り込んで4つの操舵トルク信号を得る。 - 特許庁
Therefore, the electric motor 6 can generate the steering assist torque compensating for the influences by the transmission characteristic of the steering assist torque from the electric motor 6 to the steering wheel 9 by correcting a target value defined by a detection value of a torque sensor 3 with the correction value.例文帳に追加
このため、トルクセンサ3の検出値によって定められる目標値をその補正値で補正することにより、電動モータ6は、電動モータ6から操舵輪9までの補助操舵トルクの伝達特性による影響を補償した補助操舵トルクを発生することができる。 - 特許庁
The motor driven power steering device in which steering torque applied to a dirigible road wheel is found according to the detection signal of the torque sensor, a motor current command value to be applied to a steering assist motor is determined based on the steering torque, and current based on the motor current command value is applied to drive the steering assist motor.例文帳に追加
トルクセンサの検出信号により、舵輪に加わる操舵トルクを求め、その操舵トルクに基づき、操舵補助用モータに通電すべきモータ電流指令値を定め、モータ電流指令値に基づく電流を通電して操舵補助用モータを駆動する電動パワーステアリング装置。 - 特許庁
The torque sensor is provided with upper shafts 1 and 2 that are connected to an input shaft 4 to transfer a torque being applied externally and detects a torque that is transferred to the input shaft 4 based on the change in magnetic field being generated at the outer periphery of a connection shaft 5 that is connected to the input shaft 4 and an output shaft 7.例文帳に追加
外部から加わるトルクを伝達すべく、その入力軸4に連結された上部軸1,2を備え、入力軸4に伝達されたトルクを、入力軸4と出力軸7とを連結した連結軸5の外周に生じた磁界の変化に基づき検出するトルクセンサ。 - 特許庁
With a stabilizer 8 fixed at one end to a vehicle body side member 2 and coupled at the other 8c to a shock absorber 6 via a torsional torque input mechanism 18, the system works the torsional torque input mechanism 18 in dependence on sensor information to generate torsional torque at the other end 8c of the stabilizer 8.例文帳に追加
スタビライザ8の一端を車体側部材2に固着し、スタビライザの他端8cを、ねじりトルク入力機構18を介してショックアブソーバ6に連結し、センサ情報に基づいてねじりトルク入力機構を作動してスタビライザの他端側にねじりトルクを発生させる装置である。 - 特許庁
This operation characteristic measurement device is used for measuring an operation characteristic of the linear motion mechanism 1, and provided with a mounting part 60 for mounting the linear motion mechanism 1 thereto, a motor 65 for imparting rotating torque to the nut 20, and a torque sensor 67 detecting the rotating torque imparted to the nut 20 from the motor 65.例文帳に追加
作動特性測定装置は直動機構1の作動特性を測定するものであり、直動機構1が装着される装着部60と、ナット20に回転トルクを付与する電動機65と、電動機65からナット20に付与される回転トルクを検出するトルクセンサ67とを備える。 - 特許庁
To provide an angular velocity and angular acceleration calculation device calculating a crank angular velocity and an angular acceleration from a crank angle sensor signal, a torque estimation device estimating gas pressure torque and external force torque, and a combustion state estimation device estimating a combustion state.例文帳に追加
本発明は、クランク角度センサ信号からクランク角速度及び角加速度を算出する角速度及び角加速度算出装置、ガス圧トルクとともに外力トルクを推定するトルク推定装置、燃焼状態を推定する燃焼状態推定装置を提供することを目的とする。 - 特許庁
In the torque sensor 41 having both an input line 56 to which torque is input and an output line 57 for outputting a detection voltage signal according to the input torque, a previously set anomaly signal is output from the output line 57 continuously to the detection voltage signal when anomalous torque is input from the input line 56.例文帳に追加
トルクが入力される入力ライン56と、入力されたトルクに応じて検出電圧信号を出力する出力ライン57を有するトルクセンサ41において、前記入力ライン56から異常なトルクが入力されたときに、前記出力ライン57から前記検出電圧信号に続いて予め設定された異常信号を出力する。 - 特許庁
In the process for manufacturing a torque sensor detecting a variation in the permeability of a magnetostrictive material 2 caused by a torque acting on a torque transmission shaft 1 by means of coils 23 and 24, a protruding and recessed part 3 is formed at the outer circumferential surface part of the torque transmission shaft 1 by form rolling, its surface is subjected to centerless polishing and then plated with the magnetostrictive material 2.例文帳に追加
トルク伝達軸1に作用するトルクによる磁歪材2の透磁率変化をコイル23,24により検出するトルクセンサを製造する方法において、トルク伝達軸1の外周面部に転造によって凹凸部3を形成し、その後にその表面にセンタレス研磨を施し、その後にその表面に磁歪材2をメッキにより設けるようにした。 - 特許庁
This press application mechanism for the continuously variable transmission device is provided with, at least, a torque sensor mechanism generating a (press application) force related to a torque loaded by the torque in an input side and applied to an input side in an output side and, at least, a converter converting the torque and/or the force.例文帳に追加
無段変速伝動装置用の圧着機構において、入力側でトルクによって負荷されかつ出力側で入力側にかけられるトルクに関連した(圧着)力を生ぜしめる少なくとも1つのトルクセンサ機構が設けられており、前記圧着機構が、トルク及び/又は力を変換する少なくとも1つの変換装置を有している。 - 特許庁
In the electric power steering device, a q-axis target current setting means 21 generates a q-axis current command value based on a steering input signal from a steering torque sensor TS and a vehicle speed signal from a vehicle speed sensor VS.例文帳に追加
q軸目標電流設定手段21は、操舵トルクセンサTSからの操舵入力信号と車速センサVSからの車速信号とに基づいてq軸電流指令値を生成する。 - 特許庁
The wire harness assembly 11 comprises a wire bundle 12 connecting the torque sensor 7 to the circuit board 10a, and is provided with a circuit board 13 for the sensor at the middle part in the longitudinal direction of the wire bundle 12.例文帳に追加
ワイヤハーネスアセンブリ11は、トルクセンサ7を回路基板10aに接続する電線束12を含み、電線束12の長さ方向の中間部にセンサ用回路基板13を設けてなる。 - 特許庁
To provide a method of manufacturing magnetostrictive torque sensor which controls heat treatment time during manufacturing a magnetic film, by obtaining the residual austenite content of a rotating shaft, and thereby reduces the variations in sensor sensitivity characteristics.例文帳に追加
回転軸の残留オーステナイト含有量を把握して磁性膜作製時の加熱処理時間等を制御し、センサ感度特性のバラツキを少なくできる磁歪式トルクセンサの製造方法を提供する。 - 特許庁
The paper sheet conveying device comprises an opening/closing type paper guide 232, conveying rollers 211, 212, 221, 222, a first detection sensor 241, a second detection sensor 242, a CPU 110 and a torque limiter 280.例文帳に追加
本発明の用紙搬送装置は、開閉式ペーパーガイド232、搬送ローラ211,212,221,222、第1の検出センサ241、第2の検出センサ242、CPU110およびトルクリミッタ280を備える。 - 特許庁
An assist control part 11 determines the target current value of an electric motor M based on not only outputs from a torque sensor 5 and a vehicle speed sensor 6 but also on the set condition of an automatic mode set switch 7.例文帳に追加
アシスト制御部11は、トルクセンサ5および車速センサ6の出力だけでなく、オートマチックモード設定スイッチ7の設定状態に基づいて、電動モータMの目標電流値を定める。 - 特許庁
The electric power steering device 1 includes a tubular sensor housing 34 constituted by housing a torque sensor 20 and enlarging the diameter of a column tube 31, and gear housing 32 that houses a speed reduction mechanism 24.例文帳に追加
本電動パワーステアリング装置1は、トルクセンサ20を収容しコラムチューブ31を拡径して構成された筒状のセンサハウジング34と、減速機構24を収容するギヤハウジング32とを有している。 - 特許庁
An electronic control unit 28 specifies a magnetic sensor where the abnormality occurs when the abnormality is caused as the whole torque sensor 20 when the abnormality is caused in any of two magnetic sensors 24A and 24B.例文帳に追加
電子制御ユニット28は、2つの磁気センサ24A,24Bのいずれかに異常が発生し、トルクセンサ20全体として異常が発生しているときには異常の発生している磁気センサを特定する。 - 特許庁
To suppress scattering of sensor output, even if there is a shift of axes between a steering input axis and steering output axis in the axial direction, in a torque sensor having an air gap in the axial direction.例文帳に追加
軸方向エアギャップを有するトルクセンサを前提にし、たとえ操舵入力軸と操舵出力軸との間で軸方向のズレが生じたとしてもセンサ出力のバラツキを生じにくくする。 - 特許庁
To provide a motor, having a stator and a rotor of different height and a sensor magnet for detecting rotor position where torque is increased, by utilizing the flux of the sensor magnet effectively while realizing miniaturization.例文帳に追加
ステータとロータの高さが異なり、ロータ位置検出のためのセンサマグネットを有するモータにおいて、センサマグネットの磁束を有効利用してトルクアップを図ると同時に、小型化を実現したモータを提供する。 - 特許庁
To provide a torque detecting type power steering device capable of evading such a situation as an operator conducts a steering operation without assistance of a power steering device, by detecting a trouble in a torque sensor in a stage of an insignificant trouble.例文帳に追加
本発明は、障害の程度が軽い段階にトルクセンサの障害を検出し、操作者がパワーステアリング装置による介助無しでステアリングを操作する事態を回避することできるパワーステアリング装置を提供する。 - 特許庁
To provide a control system for an elevator accurately outputting balance torque without being influenced by the weight of an elevator car and an error of a position sensor and accurately outputting torque for confirming the holding force of brake devices.例文帳に追加
乗りかごの重量と位置センサの誤差による影響を受けずに正確に吊り合いトルクを出力させ、ブレーキ装置の保持力を確認するトルクを正確に出力するエレベータの制御システムを提供する。 - 特許庁
To provide an exhaust emission control device for an internal combustion engine, to control a temperature increase means in accordance with torque by estimating the torque which is changed during the operation of the engine, using an inexpensive system without a position sensor.例文帳に追加
ポジションセンサを用いることなく安価なシステムでエンジン作動中に変化するトルクを推定し、そのトルクに基づいて昇温手段を制御することができる内燃機関の排気浄化装置を提供する。 - 特許庁
A cooling valve is provided in pipe conduits of cooling flow passages 35A, 35B reducing a temperature of the polymer material inside the heating pipe 21, and a torque of a drive motor 24 driving the internal-return screw is detected by a torque sensor 44.例文帳に追加
加熱筒21内の高分子材料の温度を低下させる冷却流路35A、35Bの管路に冷却バルブを設け、内部帰還型スクリューを駆動する駆動モータ24のトルクをトルクセンサー44で検出する。 - 特許庁
To provide a means which is for a torque sensor for vehicles, senses torque working on a power transmission member based on the strain of the power transmission member and is hardly affected by exterior and practical and new.例文帳に追加
動力伝達部材に作用するトルクを、動力伝達部材の歪みに基づいて検出する車両のトルク検出装置において、外部からの影響を受けにくく実用性の高い新規な手段を提供する。 - 特許庁
Torque to be applied to the socket 18 through the gear 22 is detected by a torque sensor 26, and the rotation angle of the socket 18 is detected by an encoder in an angle measuring gear box 24 and provided to a judging part in the main body 14.例文帳に追加
ギア22がソケット18に付与するトルクはトルクセンサ26で検出され、ソケット18の回転角度は、角度計測用ギアボックス24内のエンコーダで検出され本体14内部の判定部に提供される。 - 特許庁
A torque sensor is provided to detect torque transmitted by a steering shaft, consisting of an input shaft 3 and an output shaft 4, according to a coaxial and elastic relative rotation amount of the two shafts 3 and 4.例文帳に追加
入力シャフト3と出力シャフト4により構成されるステアリングシャフトによって伝達されるトルクを、両シャフト3、4の同軸心かつ弾性的な相対回転量に応じて検出するトルクセンサを備える。 - 特許庁
Thus, it is possible to reduce the load fluctuation of the engine 22, and to make a hybrid vehicle travel by outputting torque based on request torque Tr* to a ring gear shaft 32a while performing the sensor abnormality determination processing.例文帳に追加
これにより、エンジン22の負荷変動を小さくすることができ、センサ異常判定処理を実行しながらリングギヤ軸32aに要求トルクTr*に基づくトルクを出力して走行することができる。 - 特許庁
An HVECU 100 determines a request torque T1req by using the maximum torque which can be output by a motor generator MG1 for a motor revolving speed MRN1 to be feeded back from a revolving speed sensor 30 as an upper limit value.例文帳に追加
HVECU100は、回転数センサ30からフィードバックされるモータ回転数MRN1に対してモータジェネレータMG1が出力可能な最大トルクを上限値として、要求トルクT1reqを決定する。 - 特許庁
To exert a failsafe effect and to perform torque control by using a simpler wiring structure by causing an analog sensor itself for feedback control used for measuring external force such as force or torque to together possess a failsafe function.例文帳に追加
力又はトルク等の外力を測定するフィードバック制御用のアナログセンサ自体にフェールセーフ機能を併有させることにより、フェールセーフな力・トルク制御をより簡便な配線構造で行えるようにする。 - 特許庁
The strength of a magnetic field Hx generated by magnetic poles N and S, which occur on both end sides of the large-diameter part 16, is detected by a magnetic sensor 18 to detect the size of compressor torque by the torque detecting apparatus.例文帳に追加
トルク検出装置による圧縮機トルクの大きさの検出は、大径部16の両端側に現れる磁極N,Sにより発生する磁界Hxの強さを、磁気センサ18によって検出することで行われる。 - 特許庁
When the steering torque of the input shaft 3 detected by a torque sensor 12 varies in a speed higher than a prescribed speed, a application control part 13 turns on a switch 14 so that a voltage is applied to electric viscosity fluid E.例文帳に追加
トルクセンサ12により検出された入力軸3の操舵トルクが一定速度以上で変化する場合等に、印加制御部13がスイッチ14をオンにし、電気粘性流体Eに電圧を印加する。 - 特許庁
To provide a torque sensor improved in detecting efficiency, having both excellent magnetic and mechanical characteristics required for not only detecting but also transmitting torque, being small in the number of parts, and having excellent precision and sensitivity for detection.例文帳に追加
検出効率を向上し、トルクの検出だけでなく伝達を行う上で必要な優れた磁気特性と機械的特性とを併せ持ち、部品点数が少なく、検出精度、検出感度の良いトルクセンサを提供する。 - 特許庁
To provide a magnetostrictive torque sensor for improving detection accuracy of steering torque by causing an alternating magnetic flux not to pass through a shaft member or magnetostrictive material or coil so that it is hardly affected by the alternating magnetic flux.例文帳に追加
交流磁束が軸部材又は磁歪材又はコイルを通過しなくなり、交番磁界の影響を受けにくくして、操舵トルクの検出精度を向上させることができる磁歪式トルクセンサを提供する。 - 特許庁
The sub MCU 12 controls a motor sub drive circuit 16 in accordance with a steering torque signal from a torque sensor 2, and drives the motor sub drive circuit 16 to change over the brush motor 32 from inertia compensation control into assist control.例文帳に追加
サブMCU12は、トルクセンサ2の操舵トルク信号に基づいてモータ副駆動回路16を制御し、モータ副駆動回路16を駆動して、ブラシモータ32を慣性補償制御からアシスト制御に切り替える。 - 特許庁
Existence of vibration input of the shimmy, the judder, etc. is judged in accordance with a high frequency component by fetching the high frequency component equivalent to the shimmy and the judder from a torque detection signal T from a steering reaction torque sensor 8.例文帳に追加
操舵反力トルクセンサ8からのトルク検出信号Tからシミーやジャダーに相当する高周波数成分を取り出し、この高周波数成分に基づいてシミーやジャダー等の振動入力の有無を判断する。 - 特許庁
A braking force Fbk is estimated according to a brake hydraulic pressure detected by a brake hydraulic pressure sensor, and a creep torque creepT is reduced to correct according to a brake side torque (Fbk×Rtyre) obtained from the braking force Fbk (step S4).例文帳に追加
ブレーキ油圧センサにて検出されたブレーキ油圧に基づいてブレーキ力Fbkを推定し、そのブレーキ力Fbkから求めた制動側のトルク(Fbk×Rtyre)に応じてクリープトルクcreepTを減少補正する(ステップS4)。 - 特許庁
The steering torque transmitted by a steering shaft formed of first shaft 3 and second shaft 4 elastically relatively rotatable around an axis is detected by a torque sensor 1 on the basis of the relative rotation.例文帳に追加
軸中心に弾性的に相対回転可能な第1シャフト3と第2シャフト4により構成されるステアリングシャフトによって伝達される操舵トルクを、その相対回転に基づきトルクセンサ1により検出する。 - 特許庁
Further, when the value of detection signal exceeds threshold values LT, UT set out of the range of detection signal, the abnormality of torque sensor can be accurately detected while enhancing the allowable torque of the torsion bar.例文帳に追加
更に、検出信号の範囲外に設定された閾値LT、UTを、検出信号が超えたとき又は下回ったとき、トーションバーの許容トルクを高めながらも、精度良くトルクセンサの異常を検出することができる。 - 特許庁
To provide a torque sensor capable of restraining, to the minimum, reduction of a magnetic flux caused by formation of a cut-out provided in a yoke of a coil unit.例文帳に追加
コイルユニットのヨークに設けた切欠の形成による磁束の減少を最小限に抑えることが可能なトルクセンサを提供すること。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|