| 例文 |
command elementの部分一致の例文一覧と使い方
該当件数 : 319件
When a start switch is turned on, an anomaly discharge command dis1 is outputted and an operation of each high potential-side switching element Swp at anomaly discharge control is simulated.例文帳に追加
起動スイッチがオン操作されると、異常時放電指令dis1を出力することで、異常時放電制御を行なう場合の高電位側のスイッチング素子Swpの操作を模擬する。 - 特許庁
A comparator S6 compares the output of a picture element counter S4 with the set value of a W set storage register S5 and outputs a data write command to the FIFO type memory S3 when they are equal in comparison.例文帳に追加
比較器S6が画素カウンタS4の出力とW設定記憶レジスタS5の設定値を比較し、比較結果が等しければ、FIFO型メモリS3へのデータ書込みを指令する。 - 特許庁
With the failure A diagnosed, the failure diagnosis operating opening θX at this time is used as a limiting value in the direction of the opening command value θspnew to change the opening control range of a valve element.例文帳に追加
故障Aと診断した場合、その時の故障診断動作開度θXを開度指令値θspnew の方向への限界値として弁体の開度制御範囲を変更する。 - 特許庁
In this case, by manipulating an insulation element driving unit 60, an ON manipulation command is prevented from being input into drive units DU of V-phase and W-phase upper arms and lower arms.例文帳に追加
この際、絶縁素子駆動部60を操作することで、V相およびW相のドライブユニットDUには、上側アームおよび下側アームともにオン操作指令が入力されないようにする。 - 特許庁
A controller 11 receives the signal from the photodetecting element 10 and outputs a command to vary a voltage for canceling the characteristic variation of the lens system to a power unit 8.例文帳に追加
制御装置11は、受光素子10からの信号を受けて、レンズ系の特性変化を打ち消すような電圧の変化を与えるための指令を、電源装置8に出力する。 - 特許庁
To provide a piezoelectric actuator and a fuel injector utilizing the same in which vibration in displacement of a piezoelectric element is reduced by generating a pulse to be superimposed immediately after the rise of command pulse.例文帳に追加
この発明は,コマンドパルスの立ち下げ直後に重畳パルスを発生させて圧電素子の変位の振動を低減させた圧電アクチュエータ及びそれを用いた燃料噴射装置を提供する。 - 特許庁
The other image element data are read from the CGROM 142 and transferred to an automatic transfer area 155B by the transfer control circuit 152 responding to the reception of an automatic transfer display command.例文帳に追加
その他の画像要素データは、自動転送表示コマンドの受信に応答した転送制御回路152により、CGROM142から読み出されて自動転送エリア155Bに転送される。 - 特許庁
The torque applying means applies torque to a first engagement element in such a direction as to prevent a change in the revolution speed of the first engagement member after the actuator has been actuated by the engagement start command means.例文帳に追加
トルク付与手段は、係合開始指令手段によるアクチュエータの作動後に、第1の係合部材の回転変化を抑制する方向に第1の係合要素にトルクを付与する。 - 特許庁
Information processing at the service center 16 is followed by a return transmission of the confirmed control command and the corresponding start of an actuator and a setting constituent element for operation of the elevator 24.例文帳に追加
サービス・センター(16)での情報の処理の後に、確認された制御命令の戻り伝送と、エレベータ(24)の運転のための設定構成要素とアクチュエータの対応する起動とが行われる。 - 特許庁
A mode is provided wherein a lighting/extinction control command of the light emitting part (101) of the ink tank according to the state such as the ink residual quantity is performed while accessing to the storage element (103B) is prohibited.例文帳に追加
記憶素子(103B)に対するアクセスを禁止しながら、インク残量などの状態に応じたインクタンクの発光部(101)の点灯/消灯制御命令を実行するモードを持つ。 - 特許庁
To relieve the load required to output a control command of a game control means in the case that a light emitting element control means and a delivery control means are provided independently of the game control means.例文帳に追加
発光体制御手段および払出制御手段が遊技制御手段とは独立して設けられている場合に、遊技制御手段の制御コマンド送出に要する負担を軽くする。 - 特許庁
To provide a soft switching DC-DC converter which can perform specified power supply even in the case that a small duty command is executed for a switching element.例文帳に追加
スイッチング素子に対して小さいオンデューティ指令が行われる場合においても、所定の電源供給を行うことが可能なソフトスイッチングDC−DCコンバータを提供すること。 - 特許庁
Image element data with the frequency of display set higher are read out of a CGROM in response to the reception of a pre-transfer command to be transferred to a fixed address area.例文帳に追加
表示頻度が高くなるように設定された画像要素データについては、事前転送コマンドの受信に応答して、事前にCGROMから読み出して固定アドレスエリアに転送する。 - 特許庁
The application part applies the first potential waveform selected from the two or more kinds of first potential waveform in response to a command for ejecting the liquid droplet in the first target ejecting amount to the element.例文帳に追加
印加部は、液体滴を第1目標吐出量で吐出させるための指令に応じて、複数種類の第1電位波形の中から選択した第1電位波形を、素子へ印加する。 - 特許庁
This initial biasing current signal Ib is added to current command signal Iref of the steady-state current during the period of time ranging from the start of the starting of the movable element 14 to the predetermined time t1.例文帳に追加
この初期バイアス電流信号Ibは、可動子14の起動開始から所定時間t1までの間、定常電流の電流指令信号Irefに加算される。 - 特許庁
A transfer control circuit 152 reads image element data from a selected pattern image data area in a CGROM 142 according to a selected pattern read command, writes them in the selected pattern data buffer 155A of a VRAM 155, also reads image element data from a common pattern image data area in the CGROM 142 according to a common pattern read command and writes them in a pattern array data buffer 155B.例文帳に追加
転送制御回路152は、選択図柄読出コマンドに応じてCGROM142における選択図柄画像データエリアから画像要素データを読み出して、VRAM155の選択図柄データバッファ155Aに書き込む一方で、共通図柄読出コマンドに応じてCGROM142における共通図柄画像データエリアから画像要素データを読み出して、図柄配列データバッファ155Bに書き込む。 - 特許庁
The power module incorporates a microcomputer for controlling the speed of a DC brushless motor by controlling a three-phase inverter semiconductor switching element and a power supply power factor improvement switching element, and a drive circuit for transferring the signal of the microcomputer, inputs a PWM signal for the induction motor as a speed command from the outside, and fundamental waves are interpreted as a speed command for the brushless motor.例文帳に追加
パワーモジュールに、3相のインバータ半導体スイッチング素子及び電源力率改善スイッチング素子を制御して直流ブラシレスモータを回転数制御するマイクロコンピュータと、マイクロコンピュータの信号を伝達するドライブ回路を内蔵し、外部からの速度指令として誘導電動機用PWM信号を入力し、基本波を解読してブラシレスモータに対する速度指令とする。 - 特許庁
Thus, release of a releasing side friction element is relatively quickened to fastening of a fastening side friction element decided by a fastening side hydraulic fluid pressure command value Pc, and pull-in of torque by an interlock tendency can be eliminated as an output torque waveform as indicated by a continuous line.例文帳に追加
これにより解放側摩擦要素の解放が締結側作動油圧指令値P_cで決まる締結側摩擦要素の締結に対し相対的に早められてインターロック傾向によるトルクの引き込みを実線で示す出力トルク波形のごとくに解消できる。 - 特許庁
That is, the control gains corresponding to a proportional, an integral item, and a differential item with respect to deviance of the quantity amount of the valve element from the target state quantity are calculated by using the displacement x(n) of the valve element and the last time command current amount I(n-1).例文帳に追加
すなわち、弁体の状態量と目標とする状態量との乖離度に対する比例項や積分項、微分項のそれぞれに対応する制御ゲインを、弁体の変位x(n)と前回の指令電流量I(n−1)とを用いて算出する。 - 特許庁
On the basis of an instruction command from a personal computer terminal 28 connected to the control part 27, the gate voltage value of the first amplifying element 2 and the gate voltage value of the second amplifying element 5 inputted to the control part 27 are displayed on the screen of the personal computer terminal 28.例文帳に追加
制御部27に接続されているパソコン端末28からの命令コマンドに基づき、制御部27に入力された第1の増幅素子2のゲート電圧値及び第2の増幅素子5のゲート電圧値がパソコン端末28の画面上に表示される。 - 特許庁
To provide a control device for a vehicle, preventing erroneous learning of an oil pressure command value when raising oil pressure applied to an engagement element so that the engagement element is engaged for shifting the gear stage of an automatic transmission to a high-side.例文帳に追加
自動変速機のギヤ段をハイ側に切り換えるために係合要素を係合させるべく同係合要素に作用する油圧を上昇させる際に用いられる油圧指令値が誤学習されることを防止できる車両の制御装置を提供する。 - 特許庁
A motor electric current command value Ir(s) as a control target value of a motor output is inputted to a feed-forward compensator 51 to be inputted to a control object (motor) 50 via an adder 52 and an addition element 53.例文帳に追加
モータ出力の制御目標値であるモータ電流指令値Ir (s) はフィードフォワード補償器51に入力され、加算器52、加算要素53を経て制御対象(モータ)50に入力される。 - 特許庁
To provide a control method for a fine-movement stage device, using a piezoelectric element and a control device, capable of positioning a stage at the position in accordance with a command value in a short time, without destroying a piezoelectric actuator.例文帳に追加
圧電アクチュエータを破壊することなく、且つ、指令値に応じた位置にステージを短時間で位置決め可能な圧電素子を用いた微動ステージ装置の制御方法及び制御装置を提供する。 - 特許庁
A lithographic circuit writes the image element data, which is read from the selected symbol data buffer 155C, in the symbol array data buffer 155D to create symbol array data in response to a selected symbol setting command.例文帳に追加
描画回路は、選択図柄設定コマンドに応じ選択図柄データバッファ155Cから読み出した画像要素データを図柄配列データバッファ155Dに書き込んで図柄配列データを作成する。 - 特許庁
An evaluation function J is built by a sum of differences between the predicted currents ide, iqe and command currents idr, iqr and a square of the output ξ of an integral control element using these differences as input.例文帳に追加
この予測電流ide,iqeと指令電流idr,iqrとの差と、これらの差を入力とする積分要素の出力ξの2乗との和によって、評価関数Jを構築する。 - 特許庁
A determining part 403 performs torque boost prohibition determination processing in accordance with the actually measured number of rotation Nm of the motor, temperature Tj of the power element, and basic target torque command value Tm*, a boost permission coefficient K_bst is made to be 0 at the time of determination of motor lock.例文帳に追加
判定部403は、実測モータ回転数Nmと、パワー素子の温度Tjと、基本目標トルク指令値Tm*とに応じ、トルクブースト禁止判定処理を実施し、モータロック判定時にブースト許可係数K_bstを0にする。 - 特許庁
An image-drawing circuit writes the image element data read from the selected symbol data buffer 155C on the symbol array data buffer 155D to form symbol array data in response to a selected symbol setting command.例文帳に追加
描画回路は、選択図柄設定コマンドに応じ選択図柄データバッファ155Cから読み出した画像要素データを図柄配列データバッファ155Dに書き込んで図柄配列データを作成する。 - 特許庁
To prevent stress from being applied to a motor and a power element by determining the abnormality of a PWM command signal by comparing digital comparators and by prohibiting an output from a buffer circuit.例文帳に追加
本発明は、PWM指令信号の異常をディジタルコンパレータの比較により判定し、バッファ回路からの出力を禁止して、モータ及びパワー素子へのストレス付加を防止することを目的とする。 - 特許庁
A change rate limiting ratio β of a starting element fastening pressure command value tPc is retrieved from the α on the basis of an expected map in S4 when the change is caused by the stepping and in S5 when the change is caused by the return operation.例文帳に追加
踏み込みによるものであればS4で、戻し操作によるものであればS5で、予定のマップをもとにαから、発進要素締結圧指令値tPcの変化割合制限率βを検索する。 - 特許庁
A vibration means 40 using a piezoelectic element or the like is provided in a delivery passage 25 from a prize ball delivering device 20, which delivers a prize ball in response to a control command from a control device 10, to a prize ball storage device 30.例文帳に追加
制御装置10からの制御コマンドを受けて賞球払出を行う賞球払出装置20から遊技球貯留装置30への賞球の払出通路25に圧電素子等による振動手段40を設ける。 - 特許庁
A plotting circuit 154 prepares pattern array data by reading the image element data from the selected pattern data buffer 155A according to a selected pattern setting command and writing them in the pattern array data buffer 155B.例文帳に追加
描画回路154は、選択図柄設定コマンドに応じて選択図柄データバッファ155Aから画像要素データを読み出し、図柄配列データバッファ155Bに書き込むことにより、図柄配列データを作成する。 - 特許庁
Since the new zero point of the degree of opening of the vacuum-proportion opening and closing valve, which has been determined by S11, falls slightly below a judgement value, it becomes a valve-opening command value immediately after the start of operation of the poppet valve element.例文帳に追加
そして、S11で決定された、新たな真空比例開閉弁の開度の零点は、判定値を僅かに下回るものであるから、ポペット弁体が動き始める直後の弁開度指令値となる。 - 特許庁
To prevent generation of hydraulic difference in time-serially controlling release hydraulic pressure based on detection of completion of a loss stroke of a fastening element, and quickly eliminate deviation from a target of a hydraulic pressure command value.例文帳に追加
締結要素のロスストローク終了検知を基に解放油圧を時系列制御する時の油圧段差を生じなくすると共にこれによる油圧指令値の目標からの偏差を速やかに解消する。 - 特許庁
When supplied with a reverse command signal from a reverse control unit 46, the intermittent control unit 51 determines whether or not to cause a drive element to operate intermittently, based on a stop position signal from the stop position determining unit 52.例文帳に追加
反転制御部46から反転指令信号が供給されると、間欠制御部51は、停止位置判定部52からの停止位置信号に基づき駆動体を間欠動作させるか判断する。 - 特許庁
To provide a power converter supplying power to an electric load such that an overcurrent does not flow through a circuit element performing booster operation even if the voltage command value of output voltage is increased abruptly.例文帳に追加
出力電圧の電圧指令値が急激に増加しても、昇圧動作を行なう回路素子に過電流が流れないように電気負荷に電力を供給する電圧変換装置を提供する。 - 特許庁
The inverter device 4 includes a semiconductor element such as an IGBT, operates on a command from a control device 5 and converts the supplied DC into AC to be supplied to a motor 6.例文帳に追加
インバータ装置4は、IGBTなどの半導体素子を含んで構成されており、制御装置5の指令により動作し、供給された直流を交流に変換してモータ6に供給する。 - 特許庁
When the laminated piezoelectric element 20 is displaced according to a command signal V, a displacement sensor 23 of a damping ratio increase circuit 22 detects the displacement of the piezoelectric element 20 and supplies the detection signal via a filter circuit 24 and a gain circuit 25 to a subtracter 1, whose subtraction signal is fed to a piezoelectric driver 21 to drive the piezoelectric element 20.例文帳に追加
指令信号Vに基づいて積層型の圧電素子20を変位させるとき、減衰比増大回路22における変位センサ23により圧電素子20の変位を検出し、この検出信号をフィルタ回路24、ゲイン回路25を通して減算器1に供給し、この減算器1の減算信号をピエゾドライバ21を与えて圧電素子20を駆動する。 - 特許庁
The number of packet counted here is compared with a threshold stored in a data base 14 by a manager function part 13, and when the number exceeds the threshold, a control command (automatic report transmission suppression command) for suppressing transfer of the management system data is transmitted to the object network element via a communicating part 11.例文帳に追加
ここでカウントされたパケット数とデータベース14に蓄積されている閾値とをマネージャ機能部13にて比較判定し、閾値を超えている場合には、対象となるネットワークエレメントに対して通信部11を介して管理系データの転送を抑制する制御コマンド(自動報告送信抑制コマンド)を送出する。 - 特許庁
A motor control section, i.e., a microcomputer, calculates a command value for feedback control from the difference of a target current value being set based on the steering torque and the vehicle speed and the detection value of motor current, and then calculates the duty ratio Dc of a PWM signal for turning on/off the switching element of a motor drive circuit from that command value.例文帳に追加
モータ制御部としてのマイコンは、操舵トルクおよび車速に基づき設定される目標電流値とモータ電流の検出値との偏差からフィードバック制御のための指令値を算出し、この指令値から、モータ駆動回路のスイッチング素子をオン・オフするためのPWM信号のデューティ比Dcを算出する。 - 特許庁
Further, the apparatus control device 130 is provided with a function where, when plating objective value is changed from thin plating to thick plating, pressure command change timing at which the insufficiency of plating does not occur is calculated based on the response properties of pressure as a final control element, and a preset control starting command is created in accordance with the calculated result.例文帳に追加
さらに機器制御装置130に、めっき目標値が薄めっきから厚めっきへ変更されるときには、操作端である圧力の応答特性を元にめっき不足を生じない圧力指令変更タイミングを算出し、算出結果にしたがってプリセット制御起動指令を生成する機能を備えた。 - 特許庁
An inclination state detection means 11 outputs an ultrasonic scanning command with respect to an ultrasonic emission/reception control means 10, and allows ultrasonic generating elements U1-U5 to perform an emission/reception operation sequentially, in the direction of going, from an element U1 at one end toward an element U5 at the other end.例文帳に追加
傾斜状態検出手段11は、超音波発信・受信制御手段10に対して超音波走査指令を出力し、一端側の素子U1から他端側の素子U5へ向かう方向に、超音波発生素子U1〜U5に対して順次発信・受信動作を行わせる。 - 特許庁
Thereafter, the discharge command 'dis' in an abnormality is output to perform a discharge control in an abnormality to discharge the capacitor 16 by shorting both electrodes of the capacitor 16 by turning the switching element Swp on the high potential side and the switching element Swn on the low potential side into an on-state.例文帳に追加
その後、異常時放電指令disを出力することで、高電位側のスイッチング素子Swpおよび低電位側のスイッチング素子Swnをオン状態とすることでコンデンサ16の両電極を短絡状態としてコンデンサ16を放電させる異常時放電制御を行なう。 - 特許庁
In the command value generating means 2, two integral elements 9 and 10 are cascaded, and a feedback loop is also formed with respect to an acceleration input 'dU' by adding an output through a multiplication element 11 after going through the integral element 9 on the first stage to the acceleration input.例文帳に追加
指令値発生手段2において、2つの積分要素9、10を縦列に接続するとともに、加速度入力「dU」に対して初段の積分要素9を経た後に乗算要素11を介した出力が当該加速度入力に加算されることでフィーバックループを形成した。 - 特許庁
When the switching element 14 of the discharging circuit 12 is conducted in stopping the operation, a control section 103 outputs a conduction command signal (d) to the switching element 14 on the condition that a contact of the DC circuit switch 4 and a contact of the electric motor circuit switch 25 are opened.例文帳に追加
制御部103は、運転を停止する際に放電回路12のスイッチング素子14を導通させる場合に、直流回路開閉器4の接触子と電動機回路開閉器25の接触子とが開放したことを条件として、スイッチング素子14に導通指令信号dを出力する。 - 特許庁
Thereafter, when a lamp lighting command is inputted to the output control circuit 5, the output of the oscillation circuit 4 is transmitted to a power control element SW1 via the driving circuit 3a, the power control element SW1 is driven, a voltage is generated on the secondary side of a step-up transformer 2, and the lamp 1 is lit.例文帳に追加
その後、出力制御回路5にランプ点灯指令が入力されると、発振回路4の出力が駆動回路3aを介して電力制御素子SW1に伝達され、電力制御素子SW1が駆動され、昇圧トランス2の二次側に電圧が発生し、ランプ1が点灯する。 - 特許庁
A main processing circuit 5 is capable of generating the image data of the desired color through addition of color difference element depending on parameters to the image data converted only to the luminance element with the RPU402 by inputting one command including two parameters to the camera control circuit 4.例文帳に追加
メイン処理用回路5からは、2つのパラメータを含む1つのコマンドをカメラ制御用回路4に入力することで、RPU402で輝度成分のみに変換した画像データに、パラメータに応じた色差成分が加算され任意の色みを帯びた画像データを生成することができる。 - 特許庁
When the vehicle 14 passes through a vehicle detecting part 204, that is, the emitted light from a light emitting element 200 is cut off without arriving at a light detecting element 202, a control part 18 issues a command for robots 16a, 16b and 16c to start warming-up operation.例文帳に追加
車両検出部204を車両14が通過すると、すなわち、発光素子200から出射される発光光が受光素子202に到達することなく遮られると、その信号で制御部18はロボット16a、16b、16cに対してウォーミングアップ動作の開始を指示する。 - 特許庁
A dynamometer control part includes a spring element operation means, and an electric inertia value determined by allowing the spring element operation means to have a spring characteristic value determined from the sum of electric spring rigidity setting and electric spring loss setting is calculated, and a torque command value is determined by adding the inertia value and a shaft torque signal together.例文帳に追加
動力計制御部にばね要素演算手段を設け、このばね要素演算手段に電気ばね剛性設定と電気ばね損失設定の和によるばね特性値を持たせた電気慣性値を算出し、この慣性値と前記軸トルク信号とを加算してトルク指令値とした。 - 特許庁
In addition, a control system of an XY stage device 1 is equipped with; a platen scaling element 18 which calculates platen correction quantity from a position (angle) command; and a position/phase conversion element 19 which calculates a phase corresponding to the compensation quantity from the platen correction quantity and the detected stage movable object position (angle).例文帳に追加
加えてXYステージ装置1の制御系は、位置(角度)指令からプラテン補正量を算出するプラテンスケーリング要素18と、プラテン補正量と検出したステージ可動体位置(角度)とから補償量に対応した位相を算出する位置・位相変換要素19を備えている。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|