| 意味 | 例文 |
current-sourceの部分一致の例文一覧と使い方
該当件数 : 7159件
In an unbalanced differential amplifier 11 (an unbalanced operation amplifier 10), collector currents (bias currents) at transistors Q1, Q2 and Q6 are set by pull-up resistors R1 and R2, and accordingly the EMC resistance can be improved, as compared to the conventional technique in which the collector currents are set by a constant-current source that uses a current mirror circuit.例文帳に追加
不平衡型差動増幅器11(不平衡型演算増幅器10)では、トランジスタQ1,Q2,Q6のコレクタ電流(バイアス電流)をプルアップ抵抗R1,R2によって設定しているため、カレントミラー回路を用いた定電流源により前記コレクタ電流を設定する従来技術に比べて、EMC耐量を向上できる。 - 特許庁
The device is provided with a filter circuit FL for high-frequency inhibition inserted between an alternating current power source Vs and a rectifying circuit DB, an inverter circuit INV converting an output of the rectifying circuit DB into a high-frequency output to supply it to a discharge lamp, and an impedance circuit fitted between a direct current output terminal of the rectifying circuit and the inverter circuit INV.例文帳に追加
交流電源Vsと整流回路DBとの間に挿入された高周波阻止用のフィルタ回路FLと、整流回路DBの出力を高周波出力に変換して放電灯に供給するインバータ回路INVと、整流回路DBの直流出力端間とインバータ回路INVとの間に設けられるインピーダンス回路とを備える。 - 特許庁
Here, a diode Dc, which is conducted when the parasitic capacitance Cs is charged by the resonance current of the current resonance circuit 5 after the switching element S1 is turned on and when a voltage between the drain and the source VDS of the switching element S1 is increased up to an output voltage Vo, is connected between one end of the switching element S1 and the line of the output voltage Vo.例文帳に追加
ここでは、スイッチング素子S1がオン状態になった後、電流共振回路5の共振電流によって寄生容量Csが充電され、スイッチング素子S1のドレイン・ソース間電圧VDSが出力電圧Voまで上昇すると導通するダイオードDcを、スイッチング素子S1の一端と出力電圧Voのラインとの間に接続している。 - 特許庁
A superconducting coil 1, an exciting power source 2 supplying a current to the superconducting coil 1, mechanical permanent current switches 13-1...13-n, and second superconducting coils 14-1...14-n whose capacity is smaller than the superconducting coil 1, are respectively connected in series, with a plurality of serial bodies connected in parallel to the superconducting coil 1 provided.例文帳に追加
超電導コイル1と、超電導コイル1に電流を供給する励磁電源2と、機械式永久電流スイッチ(1)・・・(n)13−1・・・13−nと超電導コイル1より小容量の第2の超電導コイル1)・・・(n)14−1・・・14−nとを直列に接続し、超電導コイル1に並列接続される複数の直列体とからなる。 - 特許庁
Switch elements Q1-Qn are respectively connected in parallel to a plurality of LED elements D1-Dn connected to each other in series, constant current is supplied from a constant current source 2 to the LED elements and series and parallel circuits of the switch elements, and luminance of the LED element can be individually controlled by performing ON/OFF of the switch element by a control circuit 1.例文帳に追加
直列に接続された複数のLED素子D1〜Dnの各々に並列にスイッチ素子Q1〜Qnを接続し、LED素子とスイッチ素子の直並列回路に定電流源2から定電流を供給するとともに、スイッチ素子のオンオフを制御回路1により行うことにより、LED素子の輝度を個別に制御するようにした。 - 特許庁
The control circuit is composed of a capacitor 30 connected between the control node and the reference node of the starting switches, a current source for charging the capacitor, and a voltage break-over switch 32 connected so as to receive the voltage of the capacitor, conducting a current when the voltage reaches a sufficient level and keeping the starting switches in a turned-off state.例文帳に追加
制御回路は、起動スイッチの制御ノード及び基準ノードの間に結合されるキャパシタ(30)と、キャパシタを充電する電流源と、キャパシタの電圧を受取るように結合されていて、その電圧が十分なレベルに達したときに導電して、起動スイッチをターンオフの状態に保つ電圧ブレークオーバ・スイッチ(32)で構成される。 - 特許庁
To provide an image sensor and a manufacturing method thereof, which can prevent a reset noise and a dark current and causes no charge sharing phenomenon by increasing a fill-ratio and providing a smooth movement path for photocharges between a photodiode and a readout circuitry, and can prevent saturation and a decrease in sensitivity by minimizing a dark current source.例文帳に追加
充てん比を高めることと、フォトダイオードとリードアウト回路の間にフォトチャージの円滑な移動通路を提供することで、リセット雑音や暗電流の防止と、電荷共有現象が発生せず、暗電流ソースを最小化して、サチュレーション及び感度の低下を防止することのできるイメージセンサ及びその製造方法を提供する。 - 特許庁
This ion source device is equipped with a slit adjusting plate 6 mounted on an arc chamber 2 for varying the opening area of a slit 5, a motor 8 for driving the slit adjusting plate 6, and a controller 13 for controlling the motor 8 based on the result of comparison of a measured ion-beam current Ia with a previously set-up target ion-beam current Ib.例文帳に追加
開示されているイオン源装置は、アークチャンバ2に取り付けられてスリット5の開口面積を可変させるスリット調整板6と、このスリット調整板6を駆動するモータ8と、測定イオンビーム電流Iaと予め設定された目標イオンビーム電流Ibとの比較結果に基づいてモータ8を制御するコントローラ13とを備えている。 - 特許庁
To solve the problem that a termination structure provided with a JTE layer greatly deteriorates in breakdown voltage since a level and a defect present in an interface between a semiconductor layer and an insulating film or a fine amount of an external impurity in the insulating film or entering from outside up to the semiconductor interface through the insulating film becomes a generation source for a leakage current and a high current due to breakdown.例文帳に追加
JTE層を設けた終端構造では、半導体層と絶縁膜との界面に存在する準位及び欠陥、又は、絶縁膜中若しくは外部から絶縁膜を通して半導体界面まで浸入してくる微量な外来不純物が漏れ電流の発生源及び降伏点となってしまい耐圧が大幅に劣化する。 - 特許庁
A transistor TNK1 with an output signal OUTn of the differential amplifier as gate input and a transistor TNK2 with a signal OUTp having a logic opposite to that of the output signal of the differential amplification circuit as gate input are connected in series between a node GP of a common gate terminal of a mirror transistor of the current mirror type differential amplifier 1-1 and one end of a constant current source circuit TNCS.例文帳に追加
カレントミラー型差動増幅器1-1 のミラートランジスタの共通ゲート端子のノードGPと定電流源回路TNCSの一端との間に、差動増幅器の出力信号OUTnをゲート入力とするトランジスタTNK1と、差動増幅回路の出力信号とは逆の論理の信号OUTpをゲート入力とするトランジスタTNK2とを直列に接続する。 - 特許庁
Thus, since the influence of the threshold voltage of a transistor T5 is removed from the voltage between the gate and source of the transistor T5 when the voltage of the input terminal IN1 changes from high to low, subsequently, when the transistor T5 is turned on and a current flows into the transistor T5, the influence of the threshold voltage of the transistor T5 is removed also from its current value Ids.例文帳に追加
これにより、入力端子IN1の電圧がハイからローに変化する際に、トランジスタT5のゲート−ソース間電圧から、トランジスタT5の閾値電圧の影響が取り除かれるので、その後にトランジスタT5がオンしてトランジスタT5に電流が流れたときに、その電流値Idsからも、トランジスタT5の閾値電圧の影響が取り除かれる。 - 特許庁
A copying machine includes a transfer roller 71 for transferring a toner image formed on an intermediate transfer belt 64 to a recording sheet; a destaticizing member 72 for destaticizing the recording sheet to which the toner image is transferred; and an HV power source 75 for controlling second current flowing through a transfer roller 71, based on a first current flowing through the destaticizing member 72.例文帳に追加
複写機は、中間転写ベルト64上に形成されたトナー像を記録シートに転写するための転写ローラ71と、トナー像が転写された記録シートを除電するための除電部材72と、除電部材72を流れる第1の電流に基づいて、転写ローラ71を流れる第2の電流を制御するHV電源75とを備えている。 - 特許庁
A temperature detector provided herein detects the temperature by a temperature sensor and includes a periodic signal generating part which generates a periodic signal of a predetermined frequency, a current source which supplies the temperature sensor with a current according to a value of the periodic signal and a detecting part which detects the temperature on the basis of the voltage produced in the temperature sensor.例文帳に追加
温度センサにより温度を検出する温度検出装置であって、予め定められた周波数の周期信号を発生する周期信号発生部と、周期信号の値に応じた電流を温度センサに供給する電流源と、温度センサに生じる電圧に基づいて、温度を検出する検出部と、を備える温度検出装置を提供する。 - 特許庁
This projector or the like includes a lamp driving electric power control part 3 functioned as a light source driving part for outputting the first driving waveform and the second driving waveform, and a high-current ON/OFF switching part 5 functioned as a current control instruction part for control-instructing switching between the first driving waveform and the second driving waveform output from the lamp driving electric power control part 3.例文帳に追加
第1の駆動波形と第2の駆動波形とを出力する光源駆動部としてのランプ駆動電力制御部3と、ランプ駆動電力制御部3から出力する第1の駆動波形および第2の駆動波形の切替えの制御指示を行う電流制御指示部としての高電流ON/OFF切替部5とを備える。 - 特許庁
A time-power control scheme carried out by the control system 28 is carried out so that the amount of induction heating from the bottom of molten metal lump to the upper part in a vessel is gradually decreased by changing the voltage output of the power source, current output or the magnitude of the combination of the voltage output and the current output.例文帳に追加
制御システム28により実施される時間−電力管理スキームが、電源の電圧出力、電流出力、または電圧出力及び電流出力の組み合わせの各大きさを変化させることにより、容器中の溶湯塊の底部から上部にかけての誘導加熱量が徐々に減少されるように実施され得る。 - 特許庁
In a light source device, an igniter and a discharge lamp are arranged so that the direction of force acting to a light emitting point of the discharge arc determined by the direction of a line of magnetic force generating by flow of current to a secondary coil of the igniter and the direction of current formed between electrodes of the discharge lamp lit with the igniter becomes vertically lower.例文帳に追加
光源装置は、イグナイタの有する二次コイルに電流が流れることによって発生する磁力線の方向と、イグナイタによって点灯された放電ランプの電極間に形成される電流の向きとによって、放電アークの発光点に作用する決定される力の方向が鉛直下向きになるようにイグナイタと放電ランプを配置する。 - 特許庁
A capacity measuring device constituted by including a voltage source 1 with a current limit function for impressing a voltage with different voltage to a capacity to be measured and an integrator 3 capable of continuous integration functioning by repeating integrating function for measuring the integrated value of current flowing in the capacity to be measured and a capacity measuring method using the device are provided.例文帳に追加
被測定容量に異なる電圧値で電圧を印可するための電流制限機能付き電圧源1と、被測定容量を流れる電流の積分値を測定するための一定周期で積分動作を繰り返す連続積分動作可能な積分器3とを含んでなる容量測定装置とそれを用いた容量測定方法を提供する。 - 特許庁
When a driving current to an actuator 11 is increased in a load driving device 10, a current flowing to the gate of an FET 12 in the switching operation is increased, a capacitor C1 parasitic on the FET 12 is quickly charged, and the time constant of the transitional resistance change between the drain and the source in the switching operation is reduced.例文帳に追加
本発明に係る負荷駆動装置10では、アクチュエータ11への駆動電流が大きくなると、スイッチング動作時にFET12のゲートに流れる電流も大きくなり、FET12に寄生したコンデンサC1が急速に充電され、スイッチング動作時における過渡的なドレイン・ソース間の抵抗変化の時定数が小さくなる。 - 特許庁
The ECU 500 detects a stroke value and estimates a current instruction value corresponding to a null point where a supply amount of the working oil to an actuator 304 from the supply source (a pump 554 and an accumulator 552) of the working oil and a discharge amount of the working oil from the actuator 304 become to zero substantially, based on the detected stroke value and current instruction value.例文帳に追加
ECU500は、ストローク値を検出するとともに、その検出されたストローク値と電流指令値とに基づいて、作動油の供給元(ポンプ554およびアキュムレータ552)からアクチュエータ304への作動油の供給量とアクチュエータ304からの作動油の排出量とが、実質的にゼロとなるヌル点に対応する電流指令値を推定する。 - 特許庁
In this drive circuit for a stepping motor, each piece of three-phase coils is independent of each other without being connected with each other, and current application control circuits each independent of a power source are connected with independent three-phase coils so that a large current can flow on a low induced voltage of 120° in phase angle.例文帳に追加
本発明に成るステッピングモータの駆動回路においては、3相の各巻線を他の巻線とは接続せず独立させ、独立した3相巻線に夫々電源と独立した単相全波の通電制御回路を接続し、120度の位相角の低い誘起電圧のもとで大きな電流を流すことができるように構成される。 - 特許庁
The liquid crystal backlight drive circuit is connected to a DC power source 1 with an input terminal of a DC/DC converter circuit for raising voltage to a high voltage, connecting a plurality of light-emitting diodes 201 to 225 with an output terminal thereof in series, further detecting current of the light-emitting diodes 201 to 225 and stabilization-controlling the current by the DC/DC converter.例文帳に追加
直流電源1を、高い電圧に昇圧するDC/DCコンバータ回路の入力端子に接続して、出力端子に複数の発光ダイオード201〜225を直列に接続するともに、発光ダイオード201〜225の電流を検知して、その電流を前記DC/DCコンバータによって安定化制御することを特徴とした。 - 特許庁
This ageing processing method of the plasma display panel can accurately determine finishing time of ageing processing, and is composed of a step of starting the ageing processing by supplying source voltage to the plasma display panel, and a step of determining ageing finishing time by a change in a current waveform by monitoring the change in the current waveform impressed on the panel.例文帳に追加
エージング処理の終了時点を正確に決定し得るプラズマディスプレイパネルのエージング処理方法に係るもので、プラズマディスプレイパネルに電源電圧を供給することで、エージング処理を開始する段階と、パネルに印加される電流波形の変化を監視して電流波形の変化によってエージング終了時点を判断する段階とからなる。 - 特許庁
At the initial power supply stage, a halogen lamp 64 is driven by an AC current supplied from a commercial power source 105 through a driver 103, and also, a carbon lamp 65 is driven by a DC current supplied from a capacitor 106, then, the surface temperature of a fixing roll 61 is quickly increased up to a set temperature.例文帳に追加
通電初期時には、ハロゲンランプ64が商用電源105からドライバ103を介して供給される交流電流により駆動されるとともに、カーボンランプ65が蓄電装置106から供給される直流電流によって駆動されるので、定着ロール61の表面温度が設定温度まで急速に上昇する。 - 特許庁
To solve the problem that the conventional secondary electron emission rate measuring instrument is in a large scale including a charged particle generation source; a sample holder, an incident current measuring instrument; a radiation electron current measuring instrument; and an apparatus for controlling them although the measurement of secondary electron emission rate is essential to the development of a plasma display or the like.例文帳に追加
二次電子放出率の測定はプラズマディスプレイの開発などに欠かせないが、従来の二次電子放出率測定装置は荷電粒子発生源、サンプルホルダー、入射電流測定装置、放出電子電流測定装置、及びそれらの制御用装置を含んだ大掛かりなものであり、購入、維持に多額の費用が必要である。 - 特許庁
Further, in a power source to form a closed circuit which blocks the inverter output when the arc is blocked, and preserves the inductor current, loads in the forward output can be reduced by providing a current bypass circuit with a backward arc preventive diode (DA1) connected in parallel to the inverter output (INV1).例文帳に追加
また、アーク遮断時にインバータ出力を遮断し且つインダクタ電流を保存する閉回路を形成する電源においては、逆方向アーク防止ダイオード(DA1)をインバータ出力(INV1)に対して並列に接続した電流迂回路を設けることにより、やはり順方向出力時のダイオードに対する負担を減らすことができる。 - 特許庁
From the input DC bus bar current detection value IDC of the power converter with a DC power source 21 serving as an input, motor currents Id, Iq of the d axis and the q axis of the rotating coordinate system are estimated, to control output voltage of the power converter 2 in such a manner that the estimated currents Idc, Iqc match each of current command values Id^*, Iq^*.例文帳に追加
直流電源21を入力とした電力変換器の入力直流母線電流検出値IDCから、回転座標系のd軸及びq軸の電動機電流Id,Iqを推定し、推定電流Idc,Iqcが、各々の電流指令値Id^*,Iq^*に一致するように電力変換器2の出力電圧を制御する。 - 特許庁
When abnormal discharge occurs between the positive electrode ADE and a control electrode G1 or a negative electrode K, and the ampere meter APM detects increase of the dark current value, the D.C. power source DCA supplied to the positive electrode ADE is supplied by varying its voltage value to lower it so that the dark current value is set below the set value.例文帳に追加
陽極ADEと制御電極G1または陰極Kとの間に異常放電が発生し、電流計APMが暗電流値の増大を検出した場合には、暗電流値が設定値以下となるように、陽極ADEに供給する直流電源DCAの電圧値を下げるように可変させて供給する。 - 特許庁
An output current from an FET1 is converted into voltage by a resistor R1 and the voltage is fed back to the gate terminals of the FET1 and an FET2 through a source follower circuit consisting of the level shift circuits of n cascade connection diodes D1 to Dn and an FET4 and an output current is extracted from the drain terminal of the FET2.例文帳に追加
FET1の出力電流を抵抗Rlにより電圧変換し、その電圧をFET3、n個の縦続接続ダイオードD1〜Dnのレベルシフト回路、およびFET4からなるソースフォロア回路を介して、FET1およびFET2のゲート端子にフィードバックし、FET2のドレイン端子から出力電流を取り出す。 - 特許庁
A power source device 27 for converting alternating current output from an alternating generator 19 mounted on the bicycle to direct current to be supplied to an electric apparatus is provided with a first input terminal 40, a second input terminal 41, a full-wave voltage doubler rectifying circuit 42, a first output terminal 44 and a second output terminal 45.例文帳に追加
電源装置27は、自転車に装着される交流発電装置19から出力される交流電流を直流電流に変換して電気機器に供給する装置であって、第1入力端子40と、第2入力端子41と、全波倍電圧整流回路42と、第1出力端子44と、第2出力端子45とを備えている。 - 特許庁
The sealed nickel hydrogen battery uses the hydrogen storage electrode, and is formed by welding a welding point on the inner surface of a sealing plate 0 and at least one welding point out of welding points of a lead 9 and an upper current collector 2 by passing current between a positive terminal and a negative terminal of the battery from an outside power source after sealing.例文帳に追加
また、該水素吸蔵電極を適用し、封口板0の内面とリード8の溶接点およびリード9と上部集電板2の溶接点のうち少なくとも一方の溶接点を、封口後に電池の正極端子と負極端子間に外部電源により通電することにより溶接してなる密閉形ニッケル水素電池。 - 特許庁
The electrostatic drive capacitive-type actuator drive circuit 100 possessing an inductor L for storing a current energy from a power source and a capacitive-type actuator CL charged with the current stored in the inductor L makes the capacitive-type actuator CL discharge after holding the voltage charged in the capacitive-type actuator CL for a predetermined time.例文帳に追加
電源からの電流エネルギーを蓄えるインダクタLと、このインダクタLに蓄えた電流により充電される静電容量性アクチュエータCLとを具備する静電駆動静電容量性アクチュエータ駆動回路100は、静電容量性アクチュエータCLに充電した電圧を所定時間保持した後、前記静電容量性アクチュエータCLを放電する。 - 特許庁
The feeding system 11 is constituted of a constant voltage AC power source 31 and a converting circuit with reactors 32 and 35, and capacitors 33, 34 and 36, and has a constant current characteristic, a constant voltage characteristic, or an intermediate characteristic between the constant current characteristic and the constant voltage characteristic, by changing the values of the passive elements of the converting circuit.例文帳に追加
前記給電装置を、定電圧交流電源31と、リアクタ32・35、キャパシタ33・34・36による変換回路とで構成し、該変換回路は該受動素子の値を変更することにより、給電装置11が定電流特性、又は定電圧特性、又は定電流特性と定電圧特性との中間の特性となるようにする。 - 特許庁
To provide a system stabilizer having a storage device in a power system connected to a distributed power source, which compensates for the change component of tidal current of the power system via the storage device and a power converter of the system stabilization device, based on a detected signal of a current transformer disposed in the power system, thus satisfying the demand for high-speed response control.例文帳に追加
分散電源に接続された電力系統に蓄電装置を有する系統安定化装置を設け、電力系統に配設された変流器の検出信号に基づいて系統安定化装置の蓄電装置、電力変換器を介して電力系統の潮流の変動分を補償するものにおいては、その応答制御の高速化が要求される。 - 特許庁
This can reduce the resistance of a current path by a secondary electron gas 8 generated near a contact surface with the AlGaN layer 4 in the GaN layer 3, and resistance between a drain and a source by the reduction of the resistance of the current path between the respective electrodes 5, 6 and the secondary electron gas 8, thereby making compatible the high breakdown strength and the low on-resistance.例文帳に追加
これにより、GaN層3におけるAlGaN層4との接触面付近に発生する2次元電子ガス8による電流経路の低抵抗化と、各電極5、6と2次元電子ガス8との間の電流経路の低抵抗化によりドレイン・ソース間抵抗を低減でき、高耐圧化と低オン抵抗化を両立できる。 - 特許庁
The light source driving condition adjusting part 9 controls the LED driving IC 64 so as to decrease the driving current supplied to the LED 61 when the intensity of illumination of external light is high and so as to increase the driving current supplied to the LED 61 when the intensity of illumination of external light is low based on an intensity of illumination measuring result by a photometry sensor 8.例文帳に追加
また、光源駆動条件調整部9は、測光センサ7による照度計測結果において、外光の照度が高い場合には、LED61に供給する駆動電流を低減させ、外光の照度が低い場合には、LED61に供給する駆動電流を増大させるようにLED駆動IC64を制御する。 - 特許庁
The electric power steering device is provided with the motor 18 for steering assistance driven by a drive circuit 13; and the auxiliary power source 29 connected to the on-vehicle power generator 34 and the on-vehicle battery 26 in parallel and assisting the current flowing in the motor, and controls a current value flowing in the motor 18 based on steering torque detected by a torque detector 10.例文帳に追加
駆動回路13により駆動される操舵補助用のモータ18と、車載発電機34及び車載バッテリ26に並列接続され、モータ18に流す電流を補助する為の補助電源29とを備え、トルク検出器10が検出した操舵トルクに基づき、モータ18に流す電流値を制御する電動パワーステアリング装置。 - 特許庁
In the state where a bias voltage is applied to a first input terminal so as to allow a current to flow to the first MOS transistor and the fourth MOS terminal, the current source circuit synchronously controls ON/OFF of the second MOS transistor and the third MOS transistor in accordance with a switch voltage applied to a second input terminal.例文帳に追加
この電流源回路は、第1のMOSトランジスタおよび第4のMOSトランジスタに電流が流れるように第1の入力端子にバイアス電圧が印加された状態で、第2の入力端子に印加されるスイッチ電圧に応じて、第2のMOSトランジスタおよび第3のMOSトランジスタのオン/オフを同期して制御する。 - 特許庁
The present invention relates to a current drive type amplifier which inputs a sound source signal from an input terminal and drives a loudspeaker, including: the input terminal 12; an adder 14 connected to the input terminal 12; and an operational amplifier 16, connected to the adder 14, for setting mutual inductance infinite and converting an input signal IN into an output current (i).例文帳に追加
音源信号を入力端子から入力しスピーカを駆動する電流駆動型増幅装置であって、 前記入力端子12と、この入力端子12に接続された加算器14と、この加算器14に接続され相互インダクタンスを無限大に設定し入力信号INを出力電流iに変換するオペアンプ16と、を備える。 - 特許庁
This lighting system for the display device is equipped with a plurality of the light sources 17 arranged in parallel, a sensor 60 to identify information about the parallel direction of the light sources 17, and an output current control part 51 to control the amount of an output current to the light source 17 based on the identified result of the sensor 60.例文帳に追加
本発明の表示装置用照明装置は、並列配置された複数の光源17と、前記光源17の並列方向に関する情報を識別するセンサ60と、前記センサ60の識別結果に基づき、前記光源17への出力電流量を制御する出力電流制御部51と、を備えることを特徴とする。 - 特許庁
To lessen the number of scan lines when providing various correction circuits on a transistor driving by current a light emitting element by a source follower circuit configuration by being applied to a self-luminous display device due to current drive of an organic EL display device or the like, for instance, concerning the display device and a method for driving the display device.例文帳に追加
本発明は、ディスプレイ装置及びディスプレイ装置の駆動方法に関し、例えば有機EL表示装置等の電流駆動による自発光の表示装置に適用して、ソースフォロワ回路構成により発光素子を電流駆動するトランジスタに各種の補正回路を設ける場合に、走査線の数を少なくすることができるようにする。 - 特許庁
An inverter is inserted between a switching TFT and a driving TFT in each pixel and then even if the potential accumulated in the holding capacitor in the pixel varies with the OFF current of the switching TFT, the gate-source voltage of the driving TFT does not vary, so that the drain current of the driving TFT can be held constant.例文帳に追加
各画素内のスイッチング用TFTと駆動用TFTの間にインバータを挿入することで、スイッチング用TFTのOFF電流により画素内の保持容量に蓄えられる電位が変化したとしても、駆動用TFTのゲート・ソース間電圧は変化せず、駆動用TFTのドレイン電流を一定に保つことができる。 - 特許庁
In this case, a control resistor 54 formed at the same time when the detection resistor 42 is formed converts a current from a constant current source 50 into a voltage, and the converted voltage controls the variable gain amplifier 46 so that the variable gain amplifier 46 outputs the voltage V_RSSI, which is a voltage when no manufacturing variation exists in the resistance of the detection resistor 42.例文帳に追加
このとき、検出抵抗42と同時に形成された制御抵抗54により定電流源50からの電流が電圧変換され、その変換された電圧により利得可変増幅器46が検出抵抗42の抵抗値に製造ばらつきがないときの電圧VRRSIを出力するように制御される。 - 特許庁
To execute feedback control value of the current of a reference current source by using a clock, a reference voltage, and a reference capacitor in order to maintain constant settling characteristics, without depending on change of a clock period and production variations or the like of a capacitor capacitance value in a circuit accompanied with charge/discharge of a capacitor such as a switched capacitor circuit.例文帳に追加
本発明は、スイッチトキャパシタ回路等のキャパシタの充放電を伴う回路において、クロック周期の変化やキャパシタ容量値の製造ばらつき等に依存することなく、セトリング特性を一定に保つため、基準電流源の電流値をクロック、基準電圧、基準キャパシタを用いてフィードバック制御することを目的とする。 - 特許庁
The arithmetic section 22 calculates the static resistance value of the heater 15 at a room temperature and a plurality of dynamic resistance values of the heater 15 when different voltages are impressed upon the heater 15 based on the voltage value from the power source E2 and current value from the current detecting section 21 and decides the optimum driving voltage of the heater 14 corresponding to the optimum operating temperature value.例文帳に追加
演算部22は、可変電源E2の電圧値と電流検出部21からの電流値とに基づき、ヒータ15における室温時の静抵抗値と、異なるヒータ電圧印加時の複数の動抵抗値とを算出し、算出された静抵抗値と動抵抗値とに基づいて、最適動作温度値に対応する最適駆動電圧を決定する。 - 特許庁
The signal by-pass circuit 13 is constituted of a high-frequency switch 17 consisting of an n-channel FET which connects a drain between the input side capacitor 11 and an input terminal of the amplification circuit 10, and connects a source between an output terminal of an amplifier 10 and a direct-current breaking capacitor 12 through a direct-current breaking by-pass capacitor 16.例文帳に追加
前記信号バイパス回路13を、ドレインを入力側コンデンサ11と増幅回路10の入力端子との間に接続し、ソースを直流遮断用のバイパスコンデンサ16を介して増幅器10の出力端子と直流遮断用コンデンサ12との間に接続したNチャネルFETからなる高周波スイッチ17によって構成する。 - 特許庁
The inverter placed in operation switches according to this current signal to supply the inreactive power to be consumed by the system load to the system load and cancel higher harmonics generated by the system load by this output current, thereby improving the power factor of the system load which is viewed from a system power source 16 and suppress higher harmonics.例文帳に追加
運転されるインバータは、この電流信号に基づいてスイッチングすることにより、系統負荷で消費される無効電力を系統負荷へ供給すると共に、この出力電流によって系統負荷で発生される高調波を相殺し、系統電源16から見た系統負荷の力率改善と高調波抑制を図る。 - 特許庁
If a direct current output voltage Vdc of a direct current power source E decreases during the on-period Ton of the intermittent oscillation operation, an applied voltage of an induction coil 5 decreases to reduce a detecting voltage Vxs of a voltage detection circuit 14, but in the on-period Ton a diode D11 as the first mask means 17 conducts and a diode D2 is out of conduction.例文帳に追加
間欠発振動作のオン期間Tonに直流電源Eの直流出力電圧Vdcが低減すると誘導コイル5の印加電圧が減少して電圧検出回路14の検出電圧Vxsが低減するが、オン期間Tonにおいては第1のマスク手段17たるダイオードD11が導通してダイオードD2が導通しなくなる。 - 特許庁
The field effect element 10 includes a semiconductor A, a source electrode S and a drain electrode D formed on the semiconductor A, a gate electrode G for applying an electric field in a direction perpendicular to a current feed direction between the source electrode S and drain electrode D, and a gate insulating film B formed between the semiconductor A and gate electrode G.例文帳に追加
半導体Aと、半導体A上に形成されたソース電極S及びドレイン電極Dと、ソース電極S−ドレイン電極D間の通電方向に対して垂直方向に電界を印加するためのゲート電極Gと、半導体Aとゲート電極Gとの間に形成されたゲート絶縁膜Bとを備えた電界効果素子10。 - 特許庁
This ultraviolet ray emission apparatus is provided with: an ultraviolet LED for irradiating an ultraviolet-curing adhesive with ultraviolet rays; a power source for supplying an electric current to the ultraviolet LED; and a supply amperage adjusting means for adjusting the amperage to be supplied to the ultraviolet LED from the power source.例文帳に追加
紫外線硬化型接着剤に紫外線を照射するための紫外線LEDと、前記紫外線LEDに供給する電流を供給するための電源と、前記電源から前記紫外線LEDに供給する電流の量を調整するための供給電流量調整手段と、を備えることを特徴とする紫外線照射装置。 - 特許庁
The image forming section has a light source, a deflection scanning means which deflects the light beam emitted from the light source, the optical scanner equipped with an imaging optical system for imaging the light beam deflected by the scanning means in a photoreceptor form and scanning the same, and a duct through which an air current flows in one direction and which covers the optical scanner.例文帳に追加
光源、前記光源から出射される光ビームを偏向する偏向走査手段、および前記偏向し走査手段で偏向した光ビームを感光体状に結像させ、走査する結像光学系を備える光走査装置と、空気流が一方向に流通するとともに、前記光走査装置を覆うダクトとを有する画像形成装置。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|