| 例文 |
reference voltageの部分一致の例文一覧と使い方
該当件数 : 7181件
The circuit is provided with: a first comparator 11 to compare a first reference voltage Vr1 to set the off-timing of a main side transistor Q1 with a divided voltage V1 of an output voltage Vo; and a second comparator 12 to compare a second reference voltage Vr2 to set the on-timing of the main side transistor Q1 with the divided voltage V1.例文帳に追加
メイン側トランジスタQ1のオフタイミングを設定する第1基準電圧Vr1と出力電圧Voの分圧電圧V1とを比較する第1比較回路11と、メイン側トランジスタQ1のオンタイミングを設定する第2基準電圧Vr2と分圧電圧V1とを比較する第2比較回路12とを備える。 - 特許庁
The reference voltage generation circuit 48 outputs multi-valued reference voltages V0-VY by a ladder resistance circuit connected across a 1st power supply line to supply high potential side power supply voltage (1st power source voltage) and a 2nd power supply line to supply low potential side power supply voltage (2nd power source voltage) VSS.例文帳に追加
基準電圧発生回路48は、高電位側の電源電圧(第1の電源電圧)V0が供給される第1の電源線と低電位側の電源電圧(第2の電源電圧)VSSが供給される第2の電源線との間に接続されたラダー抵抗回路により、多値の基準電圧V0〜VYを出力する。 - 特許庁
The detector comprises an auxiliary power supply outputting a reference voltage, a first switching circuit for applying the voltage across the battery module to the input terminal, a second switching circuit for applying the reference voltage to the input terminal, and a controller for calculating the voltage of the module based on the output voltage.例文帳に追加
このために、参照電圧を出力する補助電源、バッテリーモジュールの両端電圧を入力端子に印加するための第1スイッチング回路、参照電圧を入力端子に印加するための第2スイッチング回路、前記出力電圧に基づいて、前記モジュールの電圧を算出するコントローラーを備える。 - 特許庁
When the brake operation is not operated, the first comparator circuit CP1 compares and decides the voltage of the second terminal T2 with the first reference voltage to output the logic circuit, while the second comparator circuit CP2 compares and decides a voltage generated by a test voltage generator P with the second reference voltage to output the logic circuit.例文帳に追加
ブレーキ操作が行われないときは、第一の比較回路CP1が第二の端子T2の電圧と第一の基準電圧とを比較判定するとともに、第二の比較回路が試験電圧発生器Pから発生した電圧と第二の基準電圧とを比較判定し論理回路に出力する。 - 特許庁
A reference tap voltage at which the delivery voltage is within the proper voltage range throughout the required periods of time is identified based on the results of determination with respect to the required periods of time and all the combinations of parameters and a proper delivery voltage for each period of time is identified based on the reference tap voltage (S213).例文帳に追加
必要な時間帯及びパラメータの全組み合わせの判定結果に基づいて、必要な時間帯を通じて送出し電圧が適正電圧範囲に含まれる基準タップ電圧を特定し、当該基準タップ電圧に基づいて各時間帯の適正な送出し電圧を特定する(S213)。 - 特許庁
While using an operational amplifier 18, an offset circuit 23 performs offset adjustment to a differential amplifier circuit 21 of a reference receiver 17 such that an output voltage of the reference receiver 17 to which a different predetermined constant voltage is inputted becomes the same voltage as a voltage imparted from an inverter threshold voltage generating circuit 16.例文帳に追加
オペアンプ18を用いて、異なる所定の定電圧が入力されたリファレンスレシーバ17の出力電圧が、インバータスレッシュ電圧生成回路16から与えられる電圧と同じ電圧になるようにリファレンスレシーバ17の差動増幅回路部21に対するオフセット調整をオフセット回路部23に行わせる。 - 特許庁
In a light emitting diode array wherein a large number of light emitting diodes are arranged, voltage comparators 3 outputting the comparison results of the voltages of the terminals of the light emitting diodes with given reference voltage are provided at every light emitting diodes and a reference voltage input terminal 7 for applying variable reference voltage judging the deterioration of the light emitting diodes to the voltage comparators 3 is provided.例文帳に追加
複数の発光ダイオード1を並べてなる発光ダイオードアレイにおいて、前記発光ダイオードの端子の電圧と与えられた基準電圧とを比較した結果を出力する電圧比較器3を各発光ダイオード毎に設け、これら電圧比較器3に対して発光ダイオードの劣化を判定する可変の基準電圧を与えるための基準電圧入力端子7を設けた。 - 特許庁
The reference voltage input circuit 14 inputs voltage supplied from a power source for reference voltage 20a to the comparator circuit 13 as the reference voltage Vr while initializing the ACIC11 and then inputs the voltage divided by a first resistor R1 and a second resistor R2 to the comparator circuit 13 under the control of the ASIC11 after completing the initialization.例文帳に追加
基準電圧入力回路14は、ASIC11のイニシャライズ動作中、基準電圧用電源20aから供給される電圧を基準電圧Vrとして比較回路13に入力し、イニシャライズ動作終了後、ASIC11の制御を受けて、第1の抵抗R1と第2の抵抗R2により分圧した電圧を基準電圧Vrとして比較回路13に入力する。 - 特許庁
The applied voltage control circuit 21 is provided with both a reference power supply 22 and a noninverting amplification circuit 23 connected to the reference power supply 22.例文帳に追加
印加電圧制御回路21は、基準電源22と、その基準電源22に接続された非反転増幅回路23とを備えている。 - 特許庁
A high-pass filter 12 is connected to the power-supply wiring, and makes the noise signals present in the power-supply wiring pass through it, by using the reference voltage V0 as a reference.例文帳に追加
ハイパスフィルタ12は、電源配線に接続され、基準電圧V0を基準として電源配線におけるノイズ信号を通過させる。 - 特許庁
A midpoint potential generating section 13 outputs a potential difference between the reference potential V1 and the reference potential V7 from nodes N2 to N6 by means of voltage division.例文帳に追加
中間電位発生部13は、ノードN2〜N6から、基準電位V1と基準電位V7との間の電位差を分圧して出力する。 - 特許庁
A reference control section applies the difference in load current to the drain current change rate in the reference table to retrieve the change in gate-source voltage.例文帳に追加
参照制御部は、負荷電流の差を参照テーブルのドレイン電流変化率に当てはめて、ゲートソース間電圧の変更量を取り出す。 - 特許庁
This operation is repeated until the detection result falls within the range of the reference, and the voltage value when the detection result falls within the range of the reference is stored in an EEPROM 7.例文帳に追加
検出結果が基準内に収まるまでそれを繰り返し、基準内に収まったときの電圧値をEEPROM7に記憶する。 - 特許庁
Such detection is repeated at each of the reference points and all switches are controlled to be opened at a point of time when detection of all reference voltage is completed.例文帳に追加
これを各基準位置で繰り返し、全ての基準電圧の検出が終了した時点で、全てのスイッチが開くように制御する。 - 特許庁
The Lev_Conv includes a self-bias type voltage amplifier Self_Bias_Volt_Amp, which amplifies the reference frequency signal of the reference frequency oscillator DCXO.例文帳に追加
このLev_Convは、基準周波数発振器DCXOの基準周波数信号を増幅する自己バイアス型電圧増幅器Self_Bias_Volt_Ampを含む。 - 特許庁
A voltage for supplying oxygen for the reference electrode 60 is impressed, and the reference electrode 60 is covered with a dense layer 57.例文帳に追加
基準電極60に酸素を供給するための酸素供給用電圧を印加すると共に、基準電極60を緻密層57で覆う。 - 特許庁
The reference circuit of this invention is used as a circuit generating reference voltage in a non-volatile semiconductor memory device, namely, in a ferroelectric random access memory device.例文帳に追加
不揮発性半導体メモリ装置、すなわち強誘電体ランダムアクセスメモリ装置において基準電圧を発生する回路として使用される。 - 特許庁
A power supply circuit 10 includes a first regulator OP1 which outputs a first power supply voltage VOUT1 based on a reference voltage Vref, and a second regulator OP2 which outputs a power supply voltage to an operating circuit of a driving circuit for driving a display panel based on the reference voltage Vref.例文帳に追加
電源回路10は、基準電圧Vrefに基づいて第1の電源電圧VOUT1を出力する第1のレギュレータOP1と、基準電圧Vrefに基づいて表示パネルを駆動する駆動回路の動作回路の電源電圧を出力する第2のレギュレータOP2とを含む。 - 特許庁
V-I converters 20 and 30 convert reference voltage into current, and time integrators 40 and 50 responding to current execute time integration of charging or discharging of a capacitor element 70, and a voltage comparator 80 compares the reference voltage with terminal voltage of the built-in capacitor element 70.例文帳に追加
V・I変換器20、30は基準電圧を電流に変換して、電流に応答する時間積分器40、50は容量70の充電または放電の時間積分を実行して、電圧比較器80は基準電圧と内蔵容量70の端子電圧とを比較する。 - 特許庁
A setting process for setting and renewing a middle point voltage output under a specific condition among output voltages of an angular velocity sensor as a reference voltage and a calculation process for calculating an angle based on the difference between the reference voltage and the output voltage of the angular velocity sensor are provided.例文帳に追加
角速度センサの出力電圧のうち所定条件下で出力される中点電圧を基準電圧として設定や更新する設定工程と、この基準電圧と角速度センサの出力電圧との差に基づいて、角度を算出する算出工程とを備える。 - 特許庁
A voltage controlled current source circuit 300 is provided with a first reference current connected to a voltage control node 350, and a current input of a voltage controlled impedance circuit 330 is reproduced through a current mirror circuit 320 at the voltage control node 350 as a second reference current.例文帳に追加
電圧制御型カレントソース回路300は、電圧制御ノード350に接続された第1基準電流を有し、電圧制御型インピーダンス回路330の電流入力331はカレントミラー回路320を介して電圧制御ノード350に第2基準電流として再生される。 - 特許庁
Here, the threshold Vr is set at a different value (step S104), according to the reference voltage Vbst (the lowest voltage Vbmin) so that it reduces the difference, by the reference voltage Vbst (for example, the lowest voltage Vbmin), in the range of the charge state corresponding to the threshold Vr.例文帳に追加
ここで、上記閾値Vrは、該閾値Vrに対応する充電状態の幅の前記基準電圧Vbst(例えば最低電圧Vbmin)による差異を緩和するように、該基準電圧Vbst(最低電圧Vbmin)に応じて異なる値に設定される(ステップS104)。 - 特許庁
When the abnormality of the system 7 is detected by a system voltage abnormality detector 21 connected to the secondary side of a voltage transformer 14, a switch circuit 23 switches a reference voltage signal from a reference voltage generator 22 inputted to a converter controller 16.例文帳に追加
計器用変圧器14の二次側に接続された系統電圧異常検出装置21により系統7の異常が検出されると、切替回路23により基準電圧発生装置22からの基準電圧信号を変換器制御装置16に入力するように切り替える。 - 特許庁
An input power switching control circuit 5 compares the 1st and 2nd measured supply voltage obtained from the circuit 4 with prescribed reference voltage, and when either one of the 1st and 2nd measured supply voltage components is lower than the reference voltage, generates fault information.例文帳に追加
入力電源切替制御回路5は、測定情報収集回路4の第1および第2の測定供給電圧と所定の基準電圧とを比較して第1および第2の測定供給電圧の1つが所定の基準電圧より低い時に障害情報を発生する。 - 特許庁
The measurement computer 12 receives an activation signal from the activation photocoupler 14; detects the output voltage from each battery cell Bn; reads the temperature from the temperature sensor 16; and calculates the magnitude of the output voltage and the temperature, based on a reference voltage read from the reference voltage generating IC.例文帳に追加
起動フォトカプラ14からの起動信号を受けて、計測用コンピュータ12は、各電池セルBnの出力電圧を検出し、温度センサ16から温度を読み込み、基準電圧発生ICから読み込んだ基準電圧に基づいて出力電圧と温度の大きさの演算を行う。 - 特許庁
The regulator includes: a switching element for turning on/off according to a pulse signal; and a PWM control circuit 20 for supplying the pulse signal corresponding to a duty ratio decided from an error voltage Verr as a difference between the output voltage and a reference voltage Vref, and the reference voltage Vref to the switching element.例文帳に追加
レギュレータは、パルス信号に応じてオン/オフを行なうスイッチング素子と、出力電圧と基準電圧Vrefとの差である誤差電圧Verrと基準電圧Vrefとから決定されるデューティ比に応じたパルス信号をスイッチング素子に供給するPWM制御回路20とを備える。 - 特許庁
Even when the fall of supply voltage is generated by a current which flows through the amplifier circuit block 2 and the bias generating circuit 1 at all times, the bias generating circuit 1 generates a reference voltage in the reference voltage nodes 56, 66 based on the power supply, in which the fall of voltage is occurred.例文帳に追加
アンプ回路ブロック2及びバイアス発生回路1で常時流れる電流により発生する電源電圧の降下が発生したとしても、バイアス発生回路1は、その電圧降下された電源に基づき基準電圧ノード56、66に基準電圧を発生する。 - 特許庁
The determining part 40 determines whether the operation is the Half-VDD operation or the Full-VDD operation on the basis of one of a comparison result between the power source voltage VBOT and a reference voltage V_RM- and a comparison result between the power source voltage VTOP and a reference voltage V_RM+ to output a determination signal 41.例文帳に追加
判定部40は、電源電圧VBOTと基準電圧V_RM−との比較結果又は電源電圧VTOPと基準電圧V_RM+との比較結果に基づき、Half−VDD動作かFull−VDD動作かを判定し、判定信号41を出力する。 - 特許庁
Based on comparison by the comparison part 12, a control part 8 makes the DC-DC converter 52 execute step-down operation when the output voltage of the alternator 3 is larger than the reference voltage, and makes the DC-DC converter 52 execute step-up operation when the output voltage of the alternator 3 is smaller than the reference voltage.例文帳に追加
制御部8は、比較部12での比較により、交流機3の出力電圧が基準電圧より大きい場合は、DC−DCコンバータ52を降圧動作させ、交流機3の出力電圧が基準電圧より小さい場合は、DC−DCコンバータ52を昇圧動作させる。 - 特許庁
An arithmetic device 29 stores beforehand the data of a reference temperature calibration curve 51 (maximum induced voltage V_kmax, minimum induced voltage V_kmin) of a sensor 21a for measuring a cast piece temperature, which is used as a reference, and the maximum induced voltage V_max and the minimum induced voltage V_min of a sensor 21b for measuring the cast piece temperature.例文帳に追加
演算装置29は、基準となる鋳片温度測定用センサー21aの基準温度検量線51(最大誘導電圧V_kmax、最小誘導電圧V_kmin)のデータと、鋳片温度測定用センサー21bの最大誘導電圧V_maxと最小誘導電圧V_minを、予め記憶する。 - 特許庁
A controller 33 of the AD converter 3 repeatedly performs a conversion operation of performing the inverse integration of a reference voltage-Vr until an output voltage Vs from an integration circuit 31 reaches a reference voltage Vo after integrating a measured voltage Vi until a predetermined integration time elapses.例文帳に追加
AD変換器3の制御装置33は、所定の積分時間が経過するまで測定電圧Viを積分した後、積分回路31からの出力電圧Vsが標準電圧Voに達するまで基準電圧−Vrを逆積分する変換動作を繰り返して行う。 - 特許庁
A comparison means is provided which compares a voltage generated by the piezoelectric vibrator P3 with the reference voltage at the time when the piezoelectric vibrator P3 picks up an acoustic wave, and the comparison means generates a false digital signal if the voltage generated by the piezoelectric vibrator P3 exceeds the reference voltage.例文帳に追加
圧電振動子(P_3)が音波をピックアップするときに圧電振動子(P_3)が生成する電圧と基準電圧を比較する比較手段を有し、振動子(P_3)の生成する電圧が基準電圧を超えるとき、比較手段が擬似デジタル信号を生成することを特徴とする。 - 特許庁
At this time, a reference voltage is estimated from the command voltage value and the water temperature, the difference between the reference voltage and the command voltage value is found as an air concentration overvoltage target value, an air stoichiometric ratio is calculated based on the air concentration overvoltage target value, so that the air stoichiometric ratio is calculated without using a multidimensional map.例文帳に追加
この際、指令電圧値と水温から基準電圧を推測し、基準電圧と指令電圧値との差をエア濃度過電圧目標値として求め、エア濃度過電圧目標値に基づいてエアストイキ比を算出することで、多次元マップを用いることなくエアストイキ比を求める。 - 特許庁
Selecting a reference voltage range of the sub analog/digital converter 9 in each of the 1st-3rd stage circuits 3, 4, 5 to be a half of a reference voltage range of the digital/analog converter 10 matches an output voltage range of the digital/analog converter 10 with an output voltage range of the operational amplifier circuit 11.例文帳に追加
各段の回路3〜5内のサブA/Dコンバータ9の基準電圧レンジがD/Aコンバータ10の基準電圧レンジの1/2に設定されることにより、D/Aコンバータ10の出力電圧レンジが演算増幅回路11の出力電圧レンジに一致する。 - 特許庁
In a reference power supply section 14, a series connection of resistances R1 and R2 divides a potential difference between the supply voltage VCC and the ground voltage GND by a predetermined dividing ratio (resistance ratio of the resistances R1 and R2) to produce a voltage as a reference voltage VREF1.例文帳に追加
基準電源部14は抵抗R1及びR2の直列接続により、電源電圧VCC,接地電圧GND間の電位差を所定の分圧比率(抵抗R1及びR2による抵抗比)で分圧して得られる電圧が基準電圧VREF1として得られる。 - 特許庁
By the constitution, the reference voltage fluctuating proportionally to the power supply voltage fluctuation is outputted from the reference voltage generation circuit 4 to the differential circuit 6 and the delay fluctuation of the driver circuit is reduced even when a power supply voltage fluctuates by the switching operation of various circuit elements.例文帳に追加
この構成により、基準電圧生成回路4から電源電圧変動に比例して変動する基準電圧を差動回路6に出力し、様々な回路素子のスイッチング動作により電源電圧が変動しても、ドライバ回路の遅延変動を低減することができる。 - 特許庁
A reference voltage generation circuit 7 is constituted of a memory part 11 for memorizing digital data for setting the detection voltage Vdet of this voltage detection circuit 1, and a D/A converter 13 for converting the digital data memorized in the memory part 11 into a reference voltage Vref.例文帳に追加
基準電圧発生回路7は、電圧検出回路1の検出電圧Vdetを設定するためのデジタルデータを記憶するためのメモリ部11と、メモリ部11に記憶されたデジタルデータを基準電圧Vrefに変換するためのD/Aコンバータ13により構成されている。 - 特許庁
The voltage generation circuit 2 is used for outputting reference voltage Vref to the regulator 3 and the voltage detector 4 and for outputting a determination signal S_1 to the AND circuits 6 and 7 on the basis of normality or abnormality of the reference voltage Vref.例文帳に追加
電圧生成回路2は、基準電圧Vrefをレギュレータ3及び電圧検出器4に出力するためのものであると共に、基準電圧Vrefの正常又は異常に基づいて判定信号S_1を論理積回路6、7に出力するためのものである。 - 特許庁
To set a reference voltage in a semiconductor integrated circuit with simple constitution as to a voltage setting circuit which sets the reference voltage needed in the semiconductor integrated circuit and an output current variable buffer which generates an output current corresponding to the set voltage.例文帳に追加
本発明は半導体集積回路内で必要となる基準の電圧を設定する電圧設定回路および設定された電圧に応じた出力電流を生成する出力電流可変バッファに関し、簡単な構成で半導体集積回路内部で基準電圧を設定する。 - 特許庁
The control voltage to control output voltage when toner concentration (5%) of developer stored in an initial developer container is detected by a standard toner concentration sensor to be reference output voltage (3V) is stored in advance as reference control voltage.例文帳に追加
標準的なトナー濃度センサで初期の現像剤収容器内に収容されている現像剤のトナー濃度(5%)を検知したときの出力電圧を基準出力電圧(3V)となるように制御する制御電圧を基準制御電圧として予め記憶しておく。 - 特許庁
In a voltage detection mode, a first reference voltage VREF is selected by a reference voltage selection circuit 5, and after setting an electric charge to the first capacitor C1 by turning on switches SW3, SWB4, a cell voltage is detected by turning off the switches SW3, SWB4 and turning on a switch SWB3.例文帳に追加
電圧検出モードでは、基準電圧選択回路5により第1基準電圧VREFを選択し、スイッチSW3、SWB4をオンして第1コンデンサC1に電荷を設定した後、スイッチSW3、SWB4をオフ、スイッチSWB3をオンしてセル電圧を検出する。 - 特許庁
The control circuit 13 opens the first switching element 11 to stop a power supply to the electric unit 3 if the charging voltage Vc is not higher than a first reference voltage VH, and closes the first switching element 11 to permit the power supply to the electric unit 3 if the charging voltage exceeds the first reference voltage VH.例文帳に追加
制御回路13は、充電電圧Vcが第1基準電圧VH以下であれば第1スイッチング素子11を開放して電動ユニット3への電力供給を禁止し、充電電圧が第1基準電圧VHを超えれば第1スイッチング素子11を閉じて電動ユニット3への電力供給を許可する。 - 特許庁
The CPU determines whether or not the voltage V1 is within a tolerance to a reference voltage value corresponding to the output current held in a reference voltage value memory (S3) and, if the tolerance is exceeded, further determines whether or not the voltage V1 is not higher than a predetermined value (S6).例文帳に追加
CPUはその電圧V1が基準電圧値メモリに保持された出力電流に対応した基準電圧値と対する許容範囲に入っているか否かを判定し(S3)、その範囲を逸脱している場合にはさらに電圧V1が所定値以下であるか否かを判定する(S6)。 - 特許庁
A voltage waveform with a time constant is applied in an area with a high gate voltage Vg1→Vg2 in the case the NMOS transistor is changed from on to off and a low reference current, and a steep voltage waveform is applied in an area with a low gate voltage Vg2→Vg3 and a reference current increased.例文帳に追加
NMOSトランジスタがオンからオフに遷移するときのゲート電圧がVg1→Vg2と高く、基準電流が低い領域ではゲートに時定数をもった電圧波形を印加し、ゲート電圧がVg2→Vg3と低く、基準電流が増加する領域で、電圧波形を急峻にする。 - 特許庁
The first differential amplifier circuit outputs a signal to turn on the second MOS transistor when the first divided voltage is higher than the reference voltage, and the first differential amplifier circuit outputs a signal to turn off the second MOS transistor when the first divided voltage is lower than the reference voltage.例文帳に追加
第1の差動増幅回路は、第1の分圧電圧が基準電圧よりも高い場合は、第2のMOSトランジスタがオンするように信号を出力し、第1の分圧電圧が基準電圧よりも低い場合は、第2のMOSトランジスタがオフするように信号を出力する。 - 特許庁
The high voltage power source has a variable voltage source (510) having a load terminal at load potential and a reference terminal at reference potential, and an auto-bias activity load circuit (520) which is connected with the load terminal and the reference terminal and constituted so as to retain a variable voltage fall between the load potential and the reference potential while keeping a nearly constant current.例文帳に追加
高電源圧電源は、負荷電位にある負荷端子及び基準電位にある基準端子を有する可変電圧源(510)と、負荷端子と基準端子との間に接続され、略一定の電流を保ちながら負荷電位と基準電位との間の可変電圧降下を維持するよう構成される自己バイアス能動負荷回路(520)とを有する。 - 特許庁
The DC voltage ea_1 inputted in the first stage DC voltage converter circuit 1_1 and a boosted high DC voltage E_N are generated between the reference potential portion 9_1 in the first stage DC voltage conversion circuit 1_1 and the high voltage side positive potential portion 10_N in the Nth stage DC voltage converter circuit 1_N.例文帳に追加
第1段直流電圧変換回路1_1の基準電位部9_1と第N段直流電圧変換回路1_Nの高圧側正電位部10_Nとの間に第1段直流電圧変換回路1_1に入力される直流電圧ea_1昇圧した直流高電圧E_Nを発生する。 - 特許庁
The semiconductor integrated circuit 30 is basically provided with a comparing part 31 for comparing a prescribed voltage with a reference voltage, an internal voltage generation part 32 for generating the internal voltage based on an output from the comparing part 31, and a resistance division part 38 for dividing an internal voltage node 37 into the prescribed voltage by resistance division.例文帳に追加
所定電圧を基準電圧と比較する比較部31と、この比較部31の出力に基づき内部電圧を生成する内部電圧生成部32と、内部電圧ノード37を抵抗分割により前記所定電圧に分圧する抵抗分割部38と、を基本的に備えている。 - 特許庁
The detected-voltage converting circuit 32 changes the reference of the detected voltage VFB 3 of the output voltage detection circuit 31 to a ground potential VSS from the input voltage VIN and converts the detected voltage VFB 3 to a new detected voltage VO 1 using the ground potential VSS as the basis.例文帳に追加
検出電圧変換回路32は、出力電圧検出回路31の検出電圧VFB3の基準を入力電圧VINからグランド電位VSSに変更させて、その検出電圧VFB3をグランド電位VSSを基準とする新たな検出電圧VO1に変換する。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|