| 例文 |
switch inputの部分一致の例文一覧と使い方
該当件数 : 4092件
On a transmission line 12 between an input terminal 10 and an output terminal 11, six resistive elements 13-18 are connected in series, and a first ground resistance element 20 and a first switch 21 are connected between a mutual connecting point 19 of the central resistive elements 13 and 14 and a ground.例文帳に追加
入力端子10及び出力端子11との間の伝送路12上に6つの抵抗素子13〜18を直列に接続し、中央の抵抗素子13、14の互いの接続点19とグラウンドとの間に第1の接地抵抗素子20及び第1のスイッチ21を接続する。 - 特許庁
A switch SW1 switches connection so as to selectively supply a signal from the output side of the terrestrial broadcast band signal of the branching filter 13 and an input terminal 12 to a universal front end 20 comprising a tuner part for receiving a plurality of broadcast signals, demodulating part and the like.例文帳に追加
スイッチSW1は、分波器13の地上放送の帯域信号の出力側と入力端子12とから、複数の放送信号を受信するチューナ部と復調部等とで構成されるユニバーサルフロントエンド20に、選択的に信号が供給されるように接続を切り換える。 - 特許庁
A control signal from the TR1 to the liquid crystal element LC is regarded as the input IN of an operation inspecting circuit 1, a logic judging circuit 3 judges whether or not it matches with an expectation, and a memory circuit 4 holds the result of the judgment and at the same time, represents it as the output OUT to a switch circuit 2.例文帳に追加
前記TR1から液晶素子LCへの制御信号を動作検証回路1の入力INとし、それが期待値と一致するか否かを論理判定回路3で判定し、判定結果をメモリ回路4で保持するとともに切換回路2への出力OUTとして導出する。 - 特許庁
An ACC resetting determination part 14 compares the target vehicle speed with a reference threshold, allows an ACC to be set again by a switch operation input from a driver when the target vehicle speed is higher than the reference threshold, and prohibits the ACC to be set again when the target vehicle speed is equal to or less than the reference threshold.例文帳に追加
そして、ACC再セット可否判定部14で目標車速を判定閾値と比較し、目標車速が判定閾値を超えているとき、ドライバのスイッチ操作入力によるACCの再セット許可と判定し、目標車速が判定閾値以下のときには、ACC再セット禁止と判定する。 - 特許庁
In this detection state, when a forced regeneration command signal S_0 is input from a forced regeneration switch 53, control signals C_p and C_f are output to a proportional solenoid valve 51 for increasing the pressure and a regulator 52 to cause a forced regeneration means (arm cylinder control valve 27 and the regulator 52) to carry out the forced regeneration.例文帳に追加
この検知状態において、強制再生スイッチ53から強制再生指令信号Soを入力したときに、制御信号Cp,Cfを昇圧用比例電磁弁51、レギュレータ52に出力し、強制再生手段(アームシリンダ制御弁27,レギュレータ52)に強制再生を実施させる。 - 特許庁
When an SPF signal at an H level is outputted from a feeding detection switch 34 at the time of resetting the microcomputer 21, a time constant generation circuit 52 is actuated to input a long time constant film set signal (FS signal) being a time constant longer than the reset time of the microcomputer 21 in the microcomputer 21.例文帳に追加
時定数発生回路52は、マイクロコンピュータ21のリセット時に、給送検出スイッチ34からHレベルのSPF信号が出力されている時に作動し、マイクロコンピュータ21のリセット時間よりも長い時定数の長時定数フイルムセット信号(FS信号)をマイクロコンピュータ21に入力する。 - 特許庁
In the emergency stop circuit of this invention, an emergency stop command is outputted from CPU1 or CPU2 through either of input circuits when at least one of emergency stop switches 1 or 2 is open-operated, switch SW10 or SW20 is opened by an output circuit 1 or 2, and emergency stop of the system is performed.例文帳に追加
非常停止スイッチ1、2の少なくとも一方が開放操作されるといずれかの入力回路を介してCPU1または2から非常停止指令が出力され、出力回路1または2により開閉器SW10または20が開放され、システムは非常停止する。 - 特許庁
Further, a step-up converter 2 capable of stepping up an input voltage to a prescribed voltage for outputting is provided between the capacitor C1 and the motor M1, so that an accumulated energy of the capacitor C1 serving as a power source for the motor M1 is effectively utilized after a main power supply switch SW1 is turned off.例文帳に追加
さらに、コンデンサC1とモータM1との間に入力電圧を所定の電圧に昇圧して出力することが可能な昇圧コンバータ2を設けることで、主電源スイッチSW1をオフ後にモータM1の電源となるコンデンサC1の蓄積エネルギーを有効に利用する。 - 特許庁
That is, when a control device 1 is provided with a function for deciding the short-circuit state and disconnected state of the sensor based on the voltage of the input terminal, the erroneous connection of the power supply built-in type sensor 19 is decided by using the decision function only by adding the switch circuit 6.例文帳に追加
すなわち、制御装置1が、入力端子の電圧に基づいてセンサの短絡状態,断線状態を判定する機能を備えている場合、スイッチ回路6を追加するだけで上記判定機能を利用して電源内蔵型センサ19の誤接続を判定できるようになる。 - 特許庁
When a parallel operation is conducted, a capacitor 107 is connected to a λ/4 line 108 by a second switch 105 to be used as an impedance converting means, output impedances of the amplifiers 103 and 104 are matched to a characteristic impedance to prevent a decrease in input/output characteristics.例文帳に追加
また、並列動作を行う場合、第2のスイッチ105によりλ/4線路108にコンデンサ107を接続してインピーダンス変換手段として用いて、各電力増幅器103,104の出力インピーダンスを特性インピーダンスに整合させて入出力特性の低下を防止する。 - 特許庁
The amplifier circuit comprises a series connection of first and second switched capacitor amplifier circuits 143, 144 each of which carries out amplification by alternately switching a first period wherein an input voltage is sampled by on/off-operations of a first switch means and a second period wherein an output voltage is subjected to a hold operation.例文帳に追加
第1スイッチ手段のオンオフ動作により入力電圧のサンプリング動作を行う第1期間と出力電圧のホールド動作を行う第2期間を交互に切り換えて増幅動作を行う第1及び第2スイッチトキャパシタ増幅回路143,144を直列接続する。 - 特許庁
In response to designation of a predetermined bit included in the communication data, a control circuit 10 makes the SW 16 switch over to the predetermined voltage input path to change the potential of a part where the predetermined bit of the first signal is located inputted to the RF-LSI 12, to a predetermined value.例文帳に追加
制御回路10は、通信データに含まれる所定ビットの指定を受けて、SW16を所定電圧入力経路に切り替えることで、RF−LSI12に入力される第1信号の所定ビットが位置する部分の電位を所定の値に変更する。 - 特許庁
An RSSI 61 detects a reception signal level and when the level exceeds a threshold value, a demodulator 62 switches the RF switch to a position of a transmission section 7 having no transmission output to provide a high attenuation to the input to the reception section so as to realize an automatic gain control function of an amplifier section with a simple circuit configuration.例文帳に追加
RSSI61で受信信号レベルを検出し、閾値を越えると復調器62はRFスイッチを送信出力のない送信部7側へ切替させ、受信部の入力に大きな減衰を与え、増幅部の自動利得制御機能を簡易な回路構成で実現可能とする。 - 特許庁
A reference current generating circuit includes an operational amplifier P2 to which reference voltage Vref is input, resistance R0 to Rk for adjusting reference current Isd2, a switch S0, P-channel electric field effect transistors MB1 to MBM for adjusting reference current Iref2, and switches S1 to SM.例文帳に追加
参照電圧Vrefが入力されるオペアンプP2と、基準電流Isd2を調整する抵抗R0〜RkおよびスイッチS0を設けるとともに、参照電流Iref2を調整するPチャンネル電界効果トランジスタMB1〜MBMおよびスイッチS1〜SMを設ける。 - 特許庁
Subsequently, when the receiving unit 15 receives a signal for locking off the door from the intelligent key and a PIN number is input through an operating unit 13, the control unit 11 controls the switch 17 to inhibit the supply of the power from the commercial power supply 16 to the outlet 18.例文帳に追加
続いて、受信部15がインテリジェントキーからドアロックをオフする信号を受信し且つ、操作部13から暗証番号の入力があると、制御部11は切替部17を制御することにより、商用電源16からの電力をコンセント18に供給することを禁止する。 - 特許庁
A microcomputer 110 switches the current direction of the relay switches 50, 60 and decides that the relay switch 50, 60 is faulty if the terminal voltage data of the DC motor M to the input terminals IN1, IN2 thereof does not correspond to the conduction stop state to the DC motor M.例文帳に追加
マイクロコンピュータ110は、リレースイッチ50、60の電流方向を切替え、その入力端子IN1、IN2への直流モータMの端子電圧データが直流モータMへの通電停止状態に対応しないとき、リレースイッチ50、60が故障していると判定する。 - 特許庁
A controller 50 detects that a gate lock lever 32 which actuates a gate lock open/close valve 33 is in locked state, that is, all of hydraulic actuators such as an arm cylinder 12 provided on an hydraulic shovel 1 are in non-operation, based on the input of a lock detection signal S1 from a gate lock detection switch 40.例文帳に追加
コントローラ50は、ゲートロック用開閉弁33を操作するゲートロックレバー32がロック状態、すなわち、油圧ショベル1に備えられたアームシリンダ12等の油圧アクチュエータの全てが非操作状態であることを、ゲートロック検知スイッチ40からのロック検知信号Slの入力により検知する。 - 特許庁
When a power source control part 2 stops power source supply to an input control part and the display control part and turns a power source control signal 9B off, the computer interrupts the supply of AC power source 6 to a power source part by turning a power source control signal 9C off and by opening an AC switch 11.例文帳に追加
電源制御部2が入力制御部と表示制御部とへの電源供給を停止し、電源制御信号9BをOFFにすると、コンピュータが、電源制御信号9CをOFFにして、ACスイッチ11を開放にし、AC電源6の電源部への供給を遮断する。 - 特許庁
The game machine is provided with an input switch for inputting the ratio of distribution to the respective jackpots when distributing game media to be consumed in the plurality of game machines connected by a communication channel to two or more kinds of jackpots and storing them, a storage device, and an arithmetic processing unit.例文帳に追加
本発明の遊技機は、通信回線により接続された複数の遊技機において消費される遊技媒体を複数種類のジャックポットに分配して貯留する際に各ジャックポットに分配する比率を入力するための入力スイッチと、記憶装置と、演算処理装置とを備える。 - 特許庁
The above compressed image signal and the above converted VGA signal are both sent to a switch 115 so that either can be selected according to the result obtained by classifying the control information input via a digital interface 118 from the outside by means of a classification device 120 and then output via the digital interface 118.例文帳に追加
上記圧縮された画像信号と上記VGA信号とはスイッチ115に送られ、その一方が外部からデジタルインターフェース118を介して入力される制御情報を判別部120で判別した結果に応じて選択され、デジタルインターフェース118を介して出力される。 - 特許庁
In S150, the microcomputer judges the signal input from the reversing end limit switch to display alarm, to stop the motor (S170) and then to transfer to ordinary control (S180), when the slide member is positioned at the reversing end, and to transfer to abnormality display (S200), when the slide member is positioned at the place excluding the reversing end.例文帳に追加
S150にて、マイコンは後進端リミットスイッチからの入力された信号を判断し、スライド部材が後進端にある場合は警報表示とモーター停止(S170)し、その後、通常制御(S180)に移行され、後進端以外に有る場合は異常表示(S200)に移行する。 - 特許庁
An n-channel first switch circuit 801 has a first main electrode terminal DA1 connected to an external input terminal T1, a second main electrode terminal SA1 connected to a first external output terminal T3, and a control electrode terminal GA1.例文帳に追加
第1スイッチング回路801、第2スイッチング回路802、第3主半導体素子QA3,第4の主半導体素子QA4、基準半導体素子QB、比較器CMP1、第1及び第2のマルチプレクサMUX1/MUX2、駆動回路111及び論理回路190とから構成される。 - 特許庁
In the case that the forward movement limit of the pusher is not input to a limit switch within a fixed time (10 sec in the example of the fig.), that is in the case the pusher cannot reach the forward movement limit, the descending action of a wing is stopped and ascends by a distance equivalent to 0.5 sec of the descending rate from the position.例文帳に追加
一定時間(図の例では、10秒)内にプッシャの前進限リミットスイッチの入力が無い場合すなわちプッシャが前進限に到達できていない場合には、ウイングの下降動作を止めて、その位置から下降速度の0.5秒分だけ上昇させる。 - 特許庁
A resolution transformation setting section 15 controls the operation of a change-over switch 13 so that the output of the bilinear processor 11 is selected, and that the output of the area average 12 is selected, when the resolution of the output image to that of the input image is 1/(integer) and 1/(non-integer), respectively.例文帳に追加
解像度変換設定部15は、入力画像の解像度に対する出力画像の解像度が、非整数分の一の場合はバイリニア処理部11の出力を、整数分の一の場合は面積平均処理部12の出力を選択するように、切替スイッチ13の動作を制御する。 - 特許庁
This antenna device is provided with a frequency variable filter 13 for switching transmission and reception bands through voltage controlled PIN diodes D1-D3 and a transmission/reception changeover switch 14 connected to an input/output terminal at one end of this frequency variable filter 13.例文帳に追加
アンテナ共用器は、送信帯域と受信帯域を電圧制御可能なPINダイオードD1〜D3によって切り換える周波数可変型フィルタ13と、この周波数可変型フィルタ13の一端の入出力端子に接続された送受信切り換えスイッチ14とを備えている。 - 特許庁
A comparator 22 compares a DC voltage obtained by rectifying, smoothing and dividing with resistance an AC voltage from an AC power source 10 with a reference voltage Vref3, and determines whether the input AC voltage is an AC100V system or an AC200V system to switchingly control a switch S1.例文帳に追加
コンパレータ22は、交流電源10からの交流電圧を整流、平滑、抵抗分圧して得られた直流電圧と、基準電圧Vref3とを比較し、入力交流電圧がAC100V系かAC200V系かを判別してスイッチS1をスイッチング制御する。 - 特許庁
An integrator 154 of a controller 102 generates an output signal 157 upon receiving an input voltage signal UVIN130 responding to the magnitude of the ac voltage source 106 and a current detection signal UIIN164 responding to a current flowing when the power switch 118 is turned on.例文帳に追加
コントローラ102の積分器154は、ac電圧源106の大きさに応答する入力電圧信号UVIN130とパワースイッチ118がオンであるときに流入する電流に応答する電流検知信号UIIN164を受て出力信号157を発生させる。 - 特許庁
The buffer BUF is configured so as to switch, corresponding to the control signals, an enable state wherein the differential signal corresponding to the differential signal inputted to the differential input terminal Di is outputted and a disable state wherein current consumption practically becomes zero and the differential output terminal becomes high impedance.例文帳に追加
バッファBUFは、差動入力端子Diに入力される差動信号に応じた差動信号を出力するイネーブル状態と、消費電流が実質的にゼロとなり、その差動出力端子がハイインピーダンスとなるディスエーブル状態と、が制御信号に応じて切りかえ可能に構成される。 - 特許庁
This password input device for a vehicle is used for the vehicle of applying a smart key system 1 for starting an engine on condition that a power switch 40 equipped in the vehicle is operated when determining as YES that a normal smart key 2 is used through electric key authentication.例文帳に追加
車両用パスワード入力装置は、電気的なキー認証により正規のスマートキー2が利用されたものと肯定判断された場合に車両備え付けのパワースイッチ40が操作されたことを条件としてエンジンが始動されるスマートキーシステム1が適用された車両に用いられる。 - 特許庁
The sheet-like switch member used for an input section of an equipment is structured of a laminated sheet including a hard layer formed of resin components, and a soft layer laminated at least on one surface of the hard layer and made from chain olefin-cyclic olefin copolymers.例文帳に追加
機器の入力部に利用されるシート状スイッチ部材を、樹脂成分で構成された硬質層と、前記硬質層の少なくとも一方の面に積層され、かつ鎖状オレフィン−環状オレフィン共重合体で構成された軟質層とを含む積層シートで構成する。 - 特許庁
A ramp waveform generating apparatus generates a reference waveform by using an input signal and generates a driving control signal for turning on and off a switch having a first terminal connected to a load and a second terminal connected to a power supply by comparing the voltage of the reference waveform with the voltage of the load.例文帳に追加
ランプ波形生成装置は、入力信号を用いて基準波形を生成し、負荷の電圧と基準波形の電圧を比較して第1端子が負荷に連結していて第2端子が電源に連結しているスイッチをオンオフさせる駆動制御信号を生成する。 - 特許庁
The control part judges that the driver does not operate the brake under a condition that signals input from the stop lamp switch indicate that there is no brake operation, when the first judgment judges no brake operation and the second judgment judges existence of the brake operation.例文帳に追加
制御部は、第1判定でブレーキ操作無しと判定しているときに第2判定でブレーキ操作有りと判定した場合には、ストップランプスイッチから入力される信号がブレーキ操作無しを示していることを条件として運転者がブレーキを操作していないと判定する。 - 特許庁
To make the device small in size and reduce the power consumption for a digital input signal processing device which inputs the voltages of the signal lines connected to the reference voltage or a power supply voltage into an information processing IC such as a microcomputer via a switch.例文帳に追加
基準電圧と電源電圧との何れかにスイッチ手段を介して接続される複数の各信号ラインの電圧を、マイコン等の情報処理用ICに入力させるデジタル入力信号処理装置において、装置の小型化と消費電力の低減とを実現する。 - 特許庁
In the device provided with a dictation software which executes a dictation function and a command software which executes a command and control function, it is determined, that which software is executed, based on the difference in the operating conditions of a speech input switch 7.例文帳に追加
ディクテーション機能を実行するディンテーションソフトとコマンドコントロール機能を実行するコマンドソフトとの2つのソフトを備えた音声認識装置において、音声入力スイッチ7の作動状態の差異により前記いずれのソフトが実行されるかが決定されるように構成した。 - 特許庁
The track hold circuit 12 blocks that analog voltage Vin is input in the first comparator CMP1 to the seventh comparator CMP 7 by turning a track hold switch SW-TH off in a correction mode for correcting offset of the first comparator CMP1 to the seventh comparator CMP7.例文帳に追加
トラックホールド回路12は、第1コンパレータCMP1〜第7コンパレータCMP7のオフセットを補正する補正モードでは、トラックホールドスイッチSW−THをオフすることにより、アナログ電圧Vinが第1コンパレータCMP1〜第7コンパレータCMP7に入力されることを遮断する。 - 特許庁
As for the first and second single wavelength signals, an optical switch 30 generates the first single wavelength signal as input optical signal if the information is 0 and generates the second single wavelength signal if the information is 1 according to a transmission electric signal having information of 0 or 1.例文帳に追加
光スイッチ30は、第1の単一波長信号及び第2の単一波長信号に対して、0又は1の情報を有する送信電気信号に従って、情報が0の場合は、第1の単一波長信号を、一方、情報が1の場合は、第2の単一波長信号を、入力光信号として出力する。 - 特許庁
When a power supply switch 26 is turned on, the input power from an on-vehicle battery 28 is directly supplied to a halogen bulb 20 from a bypass circuit 18 by bypassing a switching regulator 12, and the DC power stabilized by the switching regulator 12 is supplied to the halogen bulb 20.例文帳に追加
電源スイッチ26の投入時に、車載バッテリ28からの入力電力をスイッチングレギュレータ12をバイパスさせてバイパス回路18からハロゲンバルブ20に直接供給し、その後、スイッチングレギュレータ12によって安定化された直流電力をハロゲンバルブ20に供給する。 - 特許庁
A right hand key valid area where inputting by a right hand is valid is installed in the keyboard 105 and the input mode switch means 104 sets a right/left hand key valid mode where inputting in both the left key valid area and the right hand key valid area is validated.例文帳に追加
さらに、右手による入力が有効な右手キー有効領域をキーボード105に設け、入力モード切替手段104が、前記左手キー有効領域および前記右手キー有効領域での入力を有効とする左右手キー有効モードを設定するよう構成した。 - 特許庁
When an input accepting part 112 accepts operation information showing that the deciding operation of a first icon image has been performed, the background processing part 120 instructs the menu screen generation part 130 to switch the first background image to a second background image acquired from the recording medium.例文帳に追加
入力受付部112が、第1アイコン画像の決定操作が行われたことを示す操作情報を受け付けると、背景処理部120は、第1背景画像を、記録媒体から取得した第2背景画像に切り替えるようにメニュー画面生成部130に指示する。 - 特許庁
When a control signal ENN reaches a high level under the condition that bit lines (BL, BLZ) and the input terminals (SA, SAZ) of an amplifier circuit are connected by a CMOS switch circuit, the amplifier circuit starts amplifying the readout signal, and the amplified signal is stored.例文帳に追加
ビット線(BL,BLZ)と増幅回路の入力端子(SA,SAZ)とがCMOSスイッチ回路によって接続された状態で制御信号ENNがハイレベルになると、増幅回路において読み出し信号の増幅が開始されるとともに、その増幅された信号が保持される。 - 特許庁
An input side transistor of a current-mirror circuit (a current duplicating/distributing circuit) of parallel output which duplicates and distributes the current to be passed to terminal pins or the current to be the foundation thereof as a mirror current corresponding to the terminal pins is provided with a switch circuit in parallel or series thereto.例文帳に追加
この発明は、端子ピンに流す電流あるいはその基礎となる電流を端子ピン対応にミラー電流として複製して分配するパラレル出力のカレントミラー回路(電流複製分配回路)の入力側トランジスタに並列あるいは直列にスイッチ回路とを設ける。 - 特許庁
In the file sharing method, a client computer 1 performs input/output processing relating to file operation by accessing directly disk units 4 through a channel switch 5 based on real file information which the client computer 1 acquires from a parent server computer 2 when the open operation of file by the client computer 1.例文帳に追加
クライアントコンピュータ1によるファイルのオープン操作の際に親サーバーコンピュータ2からクライアントコンピュータ1が取得した実ファイル情報に基づいてクライアントコンピュータ1がチャネルスイッチ5を介してディスク装置4に直接的にアクセスしてファイル操作に関わる入出力処理を行う。 - 特許庁
Immediately after measurement is started, the impedance/voltage converter connects a dummy impedance Zd between the inverted input terminal and output terminal of an operational amplifier 1 by controlling a switch circuit 9 and causes a sample-and-hold circuit 10 to hold the DC voltage value corresponding to the dummy impedance Zd from an AC/DC conversion circuit 2.例文帳に追加
測定開始直後に、スイッチ回路9を制御してダミー・インピーダンスZdを演算増幅器1の反転入力端子と出力端子との間に接続し、交流/直流変換回路2からのZdに対応する直流電圧をサンプルホールド回路10にホールドさせる。 - 特許庁
When a disturbance to disable engine speed control such as noise on signal in the communication route 6 or breakage of the communication route 6 occurs to stop an engine 1, an operator switches the switch 8 to directly input command signal of the EC dial 4 to the engine controller 3.例文帳に追加
通信路6の信号にノイズが乗ったり通信路6が断線し、エンジン1が停止したり、エンジン回転数制御ができなくなるような障害が発生すると、オペレータはスイッチ8を切り換えてECダイヤル4の指示信号を直接エンジンコントローラ3に入力する。 - 特許庁
The device is provided with a switch circuit 112 controlled by the coincidence-detection output, switching the data corresponding to the defective address in a sense amplifier circuit 104 to the data selected by the set number in the redundant sense amplifier circuit 105, and connecting it to a data input/output buffer 113.例文帳に追加
その一致検出出力により制御されてセンスアンプ回路104の中の不良アドレス対応のものと冗長センスアンプ回路105のなかのセット番号により選択されたものとを切り換えてデータ入出力バッファ113に接続するスイッチ回路112を備える。 - 特許庁
In a symmetric Mach/Zehnder type optical switch (SMZ) 101 having nonlinear waveguides 1, 2 disposed in both arms, when a set light pulse S is input to the nonlinear waveguide 1 to excite changes in the nonlinear refractive index, the output light Q is changed from "0" state into "1" state.例文帳に追加
非線形導波路1および2を両アームに配置した対称マッハ・ツェンダー型光スイッチ(SMZ)101では、セット光パルスSが非線形導波路1に入力され非線形屈折率変化が励起されると、出力光Qは“0”状態から“1”状態へ変化する。 - 特許庁
When an input signal (i) varies from a low level to a high level, this switch control 200 makes a 2nd P channel MOS transistor MP2 of the 2nd output 300 turn off (Fig. 2 (l)) and a 2nd N channel MOS transistor MN2 remains on (Fig. 2 (m)).例文帳に追加
この駆動切換制御部200により、入力信号iがローレベルからハイレベルに変化する場合は、第2出力部300の第2のPチャネルMOSトランジスタMP2はオン状態からオフ状態に変化し(図2(l))、第2のNチャネルMOSトランジスタMN2は、オフ状態を維持する(図2(m))。 - 特許庁
To suppress an inrush current being generated through instantaneous charging of an input smoothing capacitor 34 in a drive load section 30 when an interlock switch 40 is turned on as the cover or door of an imaging apparatus is closed to start power supply from a power supply 30 to the drive load section 30.例文帳に追加
画像形成装置のカバーまたはドアを閉める際、インターロックスイッチ40がオンとなり、電源10から駆動負荷部30への給電が始まるが、駆動負荷部30内の駆動負荷部入力平滑コンデンサ34に電荷が一気に充電されてしまい発生する突入電流を抑える。 - 特許庁
A protection circuit 40 is disposed between a junction of the source terminal of the fourth n-channel MOSFET (Mn4) and an input terminal of the switch element, and the ground potential to lead a negative current flowing in from a drain terminal of the fourth n-channel MOSFET (Mn4) owing to electrostatic discharge to the ground potential.例文帳に追加
保護回路40は、第4nチャネルMOSFET(Mn4)のソース端子と上記スイッチ素子の入力端子の接続点と、グラウンド電位との間に設けられ、静電気放電による第4nチャネルMOSFET(Mn4)のドレイン端子から流入する負電流をグラウンド電位に流す。 - 特許庁
The 90° discrete phase unit 22 is configured of a phase distributor 23 for distributing the phase of a signal to be inputted from an input terminal 21 to 0°, 90°, 180°, and 270° and a switch part 24 for selecting the output of a phase distributor 23 according to a phase control signal 27.例文帳に追加
90°離散位相器22は、入力端子21から入力される信号の位相を0°、90°、180°、270°に分配する位相分配器23と、この位相分配器23の出力を位相制御信号27に応じて選択するスイッチ部24とから構成される。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|