| 例文 |
zero loadの部分一致の例文一覧と使い方
該当件数 : 250件
To provide a controller for automatic transmission capable of maintaining an L/U clutch (lock-up clutch) in the zero-slip condition even in case the auxiliary unit load varies during zero-slip control whereby the L/U clutch is controlled with an engaging force as small as possible so that the slip amount becomes approximately zero while the engine fuel is cut.例文帳に追加
エンジンの燃料カット中にL/Uクラッチ(ロックアップクラッチ)をできるだけ小さい締結力でスリップ量が略0になるように制御するゼロスリップ制御を行っているときに補機負荷が変動した場合でもL/Uクラッチをゼロスリップ状態に維持する。 - 特許庁
When a wheelchair hall call is registered, judgement is made whether the load signal being output of a scale device 6 to measure the intra-car load is zero or more and no more than the specified value.例文帳に追加
車椅子乗場呼びが登録されている場合に、かご内の負荷を計測する秤装置6の負荷信号が0以上でかつ所定値以下を出力しているか否かを判定する。 - 特許庁
The inverter 10 controls the oscillation frequency of an inverter circuit such that the phase angle of the inverter output current (current flowing through a load) and the inverter output voltage (voltage applied to the load) approaches zero.例文帳に追加
インバータ出力電流(負荷に流れる電流)とインバータ出力電圧(負荷に印加される電圧)との位相角がゼロに近づくようにインバータ回路の発振周波数を制御する。 - 特許庁
In the method for easing zero load on a rotating machine mechanism 1 for the fiber web machine in relation to a supporting part, the machine mechanism 1 is subjected to loads Q1, Q2 in a load direction.例文帳に追加
繊維ウェブ機械の回転する機械機構(1)の支承部との関連でゼロ荷重を緩和する方法であって、前記機械機構(1)は荷重方向に荷重(Q_1,Q_2)をかけられる。 - 特許庁
On the basis of measured results and the value of the known load, zero point and gain characteristics to be used for computing a load exerted on the hub 4, on the basis of the phase differences, are determined.例文帳に追加
そして、この測定結果と上記既知の荷重の値とにより、この位相差に基づいて上記ハブ4に加わる荷重を算出する際に利用する、零点とゲイン特性とを求める。 - 特許庁
The m+1 frequency dividing counters 3-1, 3-2 to 3-n load an initial value 'zero' when the load control is performed, output counter expiration signals 8-1, 8-2 to 8-n, when counting is expired and stop operation.例文帳に追加
m+1分周カウンタ3-1,3-2,…,3-nは、ロード制御がかかったときに初期値“0”をロードし、カウント満了するとカウンタ満了信号8-1,8-2,…,8-nを出力するとともに動作を停止させる。 - 特許庁
The position of the load change member 12 is detected by a position sensor 10, and it can be levitated to a stable position by zero power control.例文帳に追加
荷重交換部材12の位置はポジションセンサ10により検出し、ゼロパワー制御で安定する位置に浮上させることができる。 - 特許庁
To provide a pressure-sensitive device that has a long life and can accurately detect a load with a diversified size including an area near zero.例文帳に追加
長寿命であり、且つ、ゼロ近傍を含む様々な大きさの荷重を高精度に検出することができる感圧装置を提供する。 - 特許庁
To provide a screw compression device capable of reducing a thrust load applied to the thrust bearing of a rotor to zero when an operation is stopped.例文帳に追加
運転停止時にロータのスラスト軸受にかかるスラスト荷重を零とすることが可能なスクリュー圧縮装置を提供すること。 - 特許庁
An operating frequency of the converter is modulated in the vicinity of a current source frequency, and output power is adjusted from zero to full load.例文帳に追加
コンバータの動作周波数は電流源周波数付近で変調され、出力電力をゼロ負荷から全負荷まで調整する。 - 特許庁
If the count of the part 4 is more than zero, another signal processing part 5 generates a control signal to light up the illumination load L.例文帳に追加
信号処理部5は信号処理部4の計数値が零よりも多ければ、照明負荷Lを点灯させる制御信号を発生する。 - 特許庁
When a calorie fault of a fuel gas is detected in a load change of a gas turbine 5b, the load fluctuation command value of the gas turbine 5b is set to zero or reduced so that a power generation output command of the gas turbine 5b is generated on the basis of the load fluctuation command value.例文帳に追加
ガスタービン5bの負荷変化時において、燃料ガスのカロリ異常が検知された場合に、ガスタービン5bの負荷変動指令値をゼロ若しくは低減させ、この負荷変動指令値に基づいてガスタービン5bの発電出力指令を生成する。 - 特許庁
This switching power supply unit is a superior device structured, so that a power supply part may be ON-OFF controlled by detecting load connection by a load detecting means, thus bringing stand-by power next to zero in a stand-by condition, in which load is not connected.例文帳に追加
負荷検出手段により負荷接続を検出し、電源部をON・OFF制御することにより、負荷が接続されていない待機状態においては待機電力をゼロに近づけることができる優れたスイッチング電源装置を提供できる。 - 特許庁
At the time, the braking force at the time of a downward operation (DN) is made smaller than the braking force at the time of an upward operation (UP) in the vicinity of load zero.例文帳に追加
その際、下降運転(DN)時の制動力を上昇運転(UP)時の制動力よりも負荷ゼロ近傍において小さくする。 - 特許庁
Difference of these two voltage signals is identified as a bridge error voltage and the sign of that value indicates generation of zero level of load current (308, 310).例文帳に追加
それら2つの電圧信号の差をブリッジ誤差電圧として識別し、その値の符号は負荷電流ゼロレベル発生を示す(308、310)。 - 特許庁
When the switch of a load component 512 is turned on, a current flows from a rated AC power source 510 to a zero cross detecting circuit 520.例文帳に追加
負荷部品512の図示しないスイッチがONされると、定格交流電源510からゼロクロス検出回路520に電流が流れる。 - 特許庁
To provide an inexpensive AC output unit including a circuit for detecting the zero cross pint of an ac power supply for a load and a fuse fusion detecting circuit.例文帳に追加
交流負荷電源のゼロクロスポイントを検出する回路と、ヒューズ溶断検出回路を含んだ安価なAC出力ユニットを提供する。 - 特許庁
An MOS/FET switch part 19 controls the on/off of the AC power source supplied to the load 1, in the vicinity of zero potential by the switching signal.例文帳に追加
MOS・FETスイッチ部19はその切換信号によって負荷1へ供給する交流電源をゼロ電位付近でオンオフ制御する。 - 特許庁
The frequencies at the zero point for phase compensation are allowed to fluctuate according to load currents so that the fluctuation of the frequency band of a regulator can be reduced regardless of the load currents, and that excess response characteristics can be improved.例文帳に追加
負荷電流に応じて位相補償用のゼロ点の周波数を変動させることで、負荷電流によらずレギュレータの周波数帯域の変動を抑制すし、過渡応答特性を改善している。 - 特許庁
After setting rolling load and the amount of roll shift at the n-th pass, the rolling load at the (n-1)th pass is decided so that the amount of the roll shift change becomes zero or the minimum by going up reversely from the n-th pass.例文帳に追加
nパスでの圧延荷重及びロールシフト量を設定した上で、該nパスから逆上して、ロールシフト量の変更量がゼロ又は最小となるようにnー1パスの圧延荷重を決定する。 - 特許庁
A control circuit 5 performs frequency control of the inverter circuit so that difference of load current of the electric discharge lamps 4a and 4b connected in parallel and detected by a differential load current detecting circuit may be zero.例文帳に追加
制御回路5は、負荷電流差分検出回路で検出された並列接続の放電灯4a、4bの負荷電流の差分がゼロとなるようにインバータ回路の周波数制御を行う。 - 特許庁
When the pressing load by the pressure plate is zero and a member between the pair of pressure plates is in contact and in zero contact state with the adjoining member, a gap exists between the flange part 70a and the cell laminate (separator 19).例文帳に追加
プレッシャプレートによる押付荷重が0であって、一対のプレッシャプレートの間の部材が隣接する部材と当接しているゼロ接触状態のときに、鍔部70aとセル積層体(セパレータ19)の間に隙間を有する。 - 特許庁
Measurement of body weight is carried out at first just after switching on by measuring zero point that is the output of the bath scale at zero-load in the body fat meter with bath scale.例文帳に追加
体重計付き体脂肪測定装置において、測定の手順として、電源投入直後に体重計の無負荷時の出力であるゼロ点を測定し、その後被験者は体重計に乗ることで、体重測定を最初に行ってしまう。 - 特許庁
Consequently, the G sensor value under the free fall status is offset and the G sensor 3 is subjected to the zero-point correction, so that the zero-point correction of the G sensor 3 can be performed without receiving any influence of the load weight on the vehicle.例文帳に追加
したがって、自由降下状態の際にGセンサ値をオフセットとしてGセンサ3の0点補正を行うことで、車両への積載重量の影響を受けることなく、Gセンサ3の0点補正を行うことが可能となる。 - 特許庁
In the free fall status, the G sensor value to be obtained according to a detected signal of the G sensor 3 without receiving the influence of the load weight or the like on the vehicle should become zero, and when it is not zero, it seems as an offset.例文帳に追加
自由降下状態の際には、車両への積載重量などの影響を受けることなくGセンサ3の検出信号から求められるGセンサ値は0になるはずであり、0でなければそれがオフセットと考えられる。 - 特許庁
One set of the test rollers 9a, 9b is brought into contact with the wheels 12 is a substantially zero load state, and side slip of the wheels 12 is detected.例文帳に追加
前記一方の組のテスト用ローラ9a,9bを前記車輪12に略零荷重状態で接触させ、前記車輪12のサイドスリップを検出する。 - 特許庁
The wheel load therefore does not act on the ball screw mechanism 58 via the transmission member 46 in the state in which the electromagnetic driving force is zero.例文帳に追加
したがって、電磁駆動力が0である状態において、伝達部材46を介してボールねじ機構58に車輪荷重が作用することはない。 - 特許庁
The disk spring 40 has non-linear characteristics having a region that spring constant comes nearer to zero in the midway of a displacement range regarding load-displacement characteristics.例文帳に追加
皿ばね40は、荷重−変位特性に関し、変位範囲の途中においてばね定数が0に近くなる領域を持った非線形特性を有する。 - 特許庁
To provide a tire which is resistant against the load even with the zero inflation pressure, free from any overheating, and excellent in handling property and traveling comfortability.例文帳に追加
零膨張圧力のときでさえ、荷重に抵抗することができ、過熱することなく、良好なハンドリング性及び走行の快適さを可能にするタイヤを得る。 - 特許庁
As a result, when the control signal DC is at 'L' level, a current Ii is made to flow in the inverter circuit 24, but the current made to flow in the separate load 27 becomes zero.例文帳に追加
このため、制御信号DCが“L”レベルの時はインバータ回路24に電流Iiが流れる一方、別負荷27に流れる電流がゼロになる。 - 特許庁
To reduce switching loss and noise and improve the transmission efficiency of voltage by realizing zero voltage switching over the whole load range.例文帳に追加
零電圧スイッチングを全負荷領域で実現できるようにして、スイッチング損失やノイズを低減すると共に、電圧の伝達効率を向上できるようにする。 - 特許庁
The bush 15 is assembled with the roller bearing 10, and thereby, the pre-load is applied to the rolling bearing 10, and the radial inside gap is set to be equal to zero or less.例文帳に追加
このブッシュ15が転がり軸受10と組み合わされることで、転がり軸受10に予圧が付与され、そのラジアル内部すきまがゼロ以下に設定される。 - 特許庁
The constant-power control on the load L is performed by controlling the turning on/off of the switching transistor Qa of the chopper circuit CH in a continuous zero-crossing current mode.例文帳に追加
降圧チョッパ回路CHのスイッチングトランジスタQaを零クロス電流連続型でオン、オフ制御して、負荷Lの定電力制御を行なう。 - 特許庁
To precisely detect a span fluctuation portion in which a zero-point fluctuation portion is excluded, in an output of two half bridge circuits of load cells for meters.例文帳に追加
計量器に使用されるロードセルの2つのハーフブリッジ回路の出力において零点変動分を除去してスパン変動分のみを精確に検出する。 - 特許庁
The position of the load change member 33 is detected by a position sensor 28, and it is vertically moved by an actuator 17 and held at a stable position with zero power control.例文帳に追加
荷重交換部材33の位置はポジションセンサ28により検出し、アクチュエータ17によって上下動してゼロパワー制御で安定する位置に保持する。 - 特許庁
A carrier signal is injected into only the section of the power- line current which is close to zero point and does not saturate its load or a magnetic substance of a blocking-filter 3.例文帳に追加
電流の零点近傍であってブロッキングフィルタ3の磁性体の負荷電流による非飽和領域だけに搬送信号を注入するようにした。 - 特許庁
To improve the safety, when measuring a weight at a zero point, in a state wherein a fork is not loaded, in a load-measuring device for forklift.例文帳に追加
フォークリフト用荷重測定装置において、フォークに荷が載置されていない状態である零点の重量を測定する際の安全性を向上させる。 - 特許庁
At the time of adjusting a gap, a driving motor is stepped out to carry out a determination of zero point by driving the driving motor in the state that the second load is imparted by the solenoid 89.例文帳に追加
ギャップ調整時、ソレノイドにより第2負荷を与えた状態で駆動モータを駆動することにより、駆動モータを脱調させて0点出しを行う。 - 特許庁
Therefore, each dispersion of the detection accuracy of the resolvers 50, 50 is compensated by determining the difference between detection angles of both resolvers 50, 50 in the state where the load torque is zero.例文帳に追加
これにより、負荷トルクが0の状態で、両レゾルバ50,50の検出角の差分を求めると、それらレゾルバの検出精度のばらつきが相殺される。 - 特許庁
To accurately and highly precisely detect only pressure in a straight movement direction, to make the durability of a load cell longer and to perform an accurate zero reset processing.例文帳に追加
直進方向の圧力のみを正確かつ高精度に検出するとともに、ロードセルの長寿命化を図り、また、正確なゼロリセット処理を行う。 - 特許庁
Even without connection of a load consisting of a resistor and a capacitor to an output terminal 7, the presence of the capacitor 11 forms a zero in its phase characteristic.例文帳に追加
出力端7に抵抗およびコンデンサからなる負荷を接続しなくても、コンデンサ11があることによって、位相特性にゼロ点を形成することができる。 - 特許庁
When a vehicle 12 is a priority vehicle 12p and travels at a speed V lower than a predetermined value (20 [km], for example), a pre-load is applied, or when the vehicle travels at a speed V higher than the predetermined value, the pre-load is reduced (to zero), thereby applying an appropriate brake pre-load.例文帳に追加
自車12が優先車両(優先側車両)12pで、車速Vが所定値(例えば、20[km])より低い場合には予圧をかけ車速Vが所定値より高い場合では予圧を少なく(ゼロを含む)することで、的確なブレーキ予圧を付与することができる。 - 特許庁
The second shift fork 25 is a member which enables reducing or cancelling the load applied on a crankshaft 2 from a flywheel 6 to zero by adding a cancelling load on the operating load and the reverse side of the axial direction for a clutch cover 16 from the outside.例文帳に追加
第2シフトフォーク25は、クラッチカバー16に対して外部から操作荷重と軸方向反対側にキャンセル荷重を付与することで、フライホイール6からクランクシャフト2に作用する荷重を少なくとも低減させ又は相殺してゼロ近くにすることが可能な部材である。 - 特許庁
In the other hand, the size of a washing and dehydration tub 5 and the performance of a washing means accord with the rated load in the standard course and the performance of the electrolytic device 31 corresponds with the rated load in the zero- detergent course.例文帳に追加
即ち、洗濯兼脱水槽5の大きさや洗濯手段の性能は、標準コースの定格負荷量に応じたものとし、電解装置31の性能は洗剤ゼロコースの定格負荷量に応じたものとしている。 - 特許庁
A voltage between load connecting terminals is detected by a load voltage detector 12, and the time difference between zero-crossing points of the waveform of the detected voltage and the waveform of a reference voltage is detected as a phase difference for both the voltages.例文帳に追加
負荷接続端子間の電圧を負荷電圧検出回路12により検出して、検出した電圧の波形と基準電圧の波形の零クロス点間の時間差を両電圧の位相差として検出する。 - 特許庁
To provide a fixed constant velocity universal joint, wherein the load of balls coming nearest the opening end of an outer ring on a track groove is zero or nearly zero to prevent the breakage of the outer ring or a cage on the opening side of an outward member.例文帳に追加
外輪の開口端に最も近くに来たボールによるトラック溝への負荷荷重をゼロ又は、微小にできて、外方部材の開口側における外輪および保持器(ケージ)の破損を防止できる固定式等速自在継手を提供する。 - 特許庁
A leakage test circuit 12 has two current paths 12a, 12b which do not pass through a zero phase current transformer 4a between the power supply side and the load side of the zero phase transformer 4a, and includes a common current path passing through a full wave rectifier circuit 8.例文帳に追加
漏電テスト回路12は、零相変流器4aの電源側と負荷側の間で零相変流器4aを介さない2つの電流路12a,12bを有し、全波整流回路8を介した共通の電流路を備えている。 - 特許庁
Driving circuits 9 and 10 performing zero voltage switching of the first and second switching means determine a switching timing at a moment in time having a specified time lag behind a zero voltage timing detected based on the voltage across a main switch depending on the polarity of a load current Ix.例文帳に追加
第1及び第2スイッチ手段に係るゼロ電圧スイッチングを行う駆動回路9,10は、負荷電流Ixの極性に応じて、主スイッチの両端電圧に基づいて検出したゼロ電圧タイミングから所定時間遅延させた時点をスイッチタイミングとする。 - 特許庁
A stationary period output voltage in the state that a current flows to an electric load connected to the fuel cell, and a no-load voltage at a time after a certain elapsed time from a time when the current flowing from the fuel cell to the electric load is decreased to nearly zero, are measured.例文帳に追加
燃料電池に接続された電気的負荷へ電流を流している状態での定常時出力電圧と、燃料電池から電気的負荷に流している電流を略ゼロへ減少させた時から一定時間経過後の時刻における無負荷時電圧を測定する。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|