| 例文 |
controlled sourceの部分一致の例文一覧と使い方
該当件数 : 1525件
An AC power source 1 is full-wave rectified by an AC/DC switching circuit 2 to obtain a DC voltage, the DC voltage is supplied to an inverter circuit 4 via a boosting circuit 3, and a motor 5 is controlled by conducting PWM control.例文帳に追加
交流電源1をAC/DC変換回路2で全波整流して直流電圧を得、この直流電圧を昇圧回路3を介してインバータ回路4に供給するとともに、PWM制御を行ってモータ5を制御する。 - 特許庁
An inverter leading to a DC power source 5 is connected to the brushless motor 3 provided with positional sensors 4 for three phases, and the brushless motor 3 is controlled to drive, being switched in between the current application modes of the current application system for high speed, and the current application system for low speed by a controller 1.例文帳に追加
三相分の位置センサ4を設けるブラシレスモータ3に、直流電源5に連なるインバータを接続し、ブラシレスモータ3は制御装置1にて高速用通電方式と低速用通電方式の通電モードに切り換え駆動制御する。 - 特許庁
An arrival point phase regulator 5 adjusts the acceleration rate of the output frequency or controlled variables of frequency of the frequency operation portion according to an error between the phase of the AC power source and that of the inverter output to synchronize the phase at the arrival point.例文帳に追加
到達点位相レギュレータ5は、交流電源の位相とインバータ出力の位相との誤差に応じて周波数演算部の出力周波数の加速レートまたは周波数制御量を調節し、到達点での位相を同期させる。 - 特許庁
A fixing unit, where power is fed to the surface of a pressure roller, is provided with a current detection means between the pressure roller and a bias power source, and voltage applied to the pressure roller is controlled so that a current flowing when paper rushes in a fixing nip may be constant.例文帳に追加
加圧ローラ表面給電の定着器で、加圧ローラとバイアス電源の間に電流検出手段を設けておき、定着ニップに紙が突入した際に流れる電流が一定になるように加圧ローラに印加する電圧を制御する。 - 特許庁
The switching circuit 31 is controlled to provide the output voltage with a pulsating flow by adjusting a time ratio of the pulse primary voltage, and to synchronize a waveform of the output voltage with a waveform of the AC input power from an AC power source 12.例文帳に追加
スイッチング回路31は、パルス一次電圧の時比率を調整することによって、出力電力に脈流を持たせ、出力電力の波形が交流電源12からの交流入力電力の波形と同期するように制御されている。 - 特許庁
A temperature deviation between at least one selective temperature profile of the plurality of in-furnace temperature profiles near the measured heated body and a desired in-furnace temperature profile is feedback-controlled as a corrected component of a set temperature profile of the heat source.例文帳に追加
測定された被加熱体の近くの複数の炉内温度プロファイルのうち少なくとも1つの任意の温度プロファイルと、所望の炉内温度プロファイルとの偏差温度を熱源の設定温度プロファイルの修正分としてフィードバック制御をする。 - 特許庁
To provide a lighting fixture unit of a projector type vehicular headlight in which, with a light emitting element as a light source, light distribution is precisely controlled while illumination quantity is increased without blocking the reflection light advancing from a reflector to a projection lens.例文帳に追加
発光素子を光源とするプロジェクタ型の車両用前照灯の灯具ユニットにおいて、リフレクタから投影レンズへ向かう反射光を遮ることなく照射光量を増大させた上で、配光制御を精度良く行えるようにする。 - 特許庁
In the vehicle capable of independently controlling the driving force from the power source such as an engine and a motor or the like at the right and left wheels, the turning moment is generated in the vehicle by independently controlling the torque of the right and left wheels, and the traveling state is controlled.例文帳に追加
エンジンやモータなどの動力源からの駆動力を、左右輪で独立に制御することができる車両において、左右輪のトルクを独立して制御することにより車両に旋回モーメントを発生させ、走行状態を制御する。 - 特許庁
To surely close a safety valve even when a battery is consumed in a fire power adjusting device with a solenoid safety valve wherein gas supply to a burner is controlled by a motor applying the battery as its driving power source.例文帳に追加
電池を駆動電源とするモータによって、バーナへのガス供給量を制御すると共に、電磁安全弁を付属した電磁安全弁付き火力調節装置において、電池消耗時においても確実に安全弁を閉弁できるようにする。 - 特許庁
The variation in the quantity of a source light is controlled by the sum signal output of a first first-stage amplifier for detecting displacement and a second first-stage amplifier means inputted from the output of a photodetector not in use for detecting the displacement.例文帳に追加
変位を検出するための第1の初段増幅器と、変位を検出するために使用されない受光素子の出力を入力とする第2の初段増幅手段、との和信号出力により光源光量の変動を制御する。 - 特許庁
In order to suppress oscillation of the optical signal, the output intensity of the exciting light source 24 is controlled on the basis of the intensity of light having the wavelength corresponding to the energy level of rare earth in the optical fiber, thereby obtaining excellent signal quality.例文帳に追加
光信号の発振を抑圧するために、光ファイバおける希土類のエネルギー準位に相当する波長の光の強度に基づき励起光源24の出力強度を制御することで良好な信号品質を得ることができる。 - 特許庁
The current time of the circuit board 20, which varies at all times computed in real time from various parameters of the circuits board 20 and various parameters of the radiation heat source 23, and the circuit board 20 is sequentially controlled to a specified temperature, according to the sequentially computed temperature, so the current temperature of the circuit board 20 can be calculated and controlled without actually being measured.例文帳に追加
回路基板20の各種パラメータおよび輻射熱源23の各種パラメータから、経時変化する回路基板20の現在温度をリアルタイムに逐次算出し、この逐次算出される現在温度に対応して回路基板20を所定温度に逐次制御するので、回路基板20の現在温度を実際に測定することなく算出して制御できる。 - 特許庁
The clock group generating circuit has a PLL configuration including a VCO(voltage controlled oscillator) having inverter type delay stages whose buildup time and decay time can be controlled through the variation of bias voltages NBIAS and PBIAS used to drive power supply side and ground side current source transistors(TRs), and the VCO generates clock signals whose phases differ from each other.例文帳に追加
クロック群発生回路は、電源側と接地側の電流源トランジスタを駆動するバイアス電圧NBIASおよびPBIASを可変させることによって立ち上がり時間と立ち下がり時間が制御可能な複数のインバータ型遅延段を含むVCOを有したPLLの構成を有しており、このVCOから位相が異なる複数のクロック信号が生成される。 - 特許庁
Furthermore, the master-side latch circuit includes a first differential circuit which is on-off controlled on the basis of an input signal, a second differential circuit provided between a common source of the first differential circuit and one drain and on-off controlled on the basis of the control signal, and a third differential circuit storing an intermediate signal generated on the basis of the first and second differential circuits.例文帳に追加
さらに、マスター側ラッチ回路は、入力信号に基づいてオンオフ制御される第1の差動回路と、第1の差動回路の共通ソースと、一方のドレインとの間に設けられ、制御信号に基づいてオンオフ制御される第2の差動回路と、第1及び第2の差動回路に基づいて生成された中間信号を保持する第3の差動回路と、を備える。 - 特許庁
Then, the lighting state of the light source 2 for each of lighting blocks 111... is controlled by the control part 10 and each of light sources 21... (luminescent spot) lighted in the high- luminance lighting state is moved so as to flow from the vehicle entering side of a guide way R1 to the vehicle leaving side.例文帳に追加
而して、制御部10で各点灯ブロック1_11…の光源2の点灯状態を制御し、高輝度点灯状態で点灯している光源2_1…(輝点)を誘導路R1の車両進入側から車両退出側へと流れるように移動させる。 - 特許庁
A luminaire with a sensor is provided where a light source lamp 9 covered with a globe 2 of a synthetic resin material is controlled, for lighting, with an output of a heat ray detecting device 8 which detects a human body and the like by detecting a heat ray radiated from an object.例文帳に追加
合成樹脂材料製のグローブ2にて覆われた光源ランプ9を、検知対象から放射される熱線を受光し人体等の検知を行う熱線検知装置8の出力にて点灯制御するよう成したセンサ付照明器具である。 - 特許庁
By simply setting the temperature in the deposition source 11 to approximately 100 degrees, the substrate 12 is controlled to a temperature range that is appropriate for crystal growth, and ideal crystal growth where the deposition of the deposition material 11C and the high crystallization occur nearly simultaneously is achieved.例文帳に追加
蒸着源11の温度を1000度近辺に設定するだけで、基板12を結晶成長に最適な温度範囲に制御でき、蒸着材料11Cの堆積と高い結晶化とがほぼ同時に起こる理想的な結晶成長が実現される。 - 特許庁
To provide an arc evaporation source that is controlled so that magnetism between a target and a substrate is enhanced and the inclination of a magnetic line on the surface of the target becomes vertical or becomes a direction directing to the central side (inner side) from the outer circumference of a cathode surface.例文帳に追加
ターゲットと基材の間の磁力を強くするとともに、ターゲット表面における磁力線の傾きを、垂直となるように又はカソード表面の外周から中心側(内側)に向かう方向となるように制御されたアーク式蒸発源を提供する。 - 特許庁
In the manufacture, a value obtain by dividing the charged power to the ultraviolet source by the traveling speed is controlled to ≥0.5 w×min/m and ≤50 W×min/m during a linear velocity increasing period to increase the traveling speed of the wire body from 100 m/min.例文帳に追加
この製造において、線条体の走行速度を100m/minから上昇させる線速上昇期間において、紫外線光源への投入電力を走行速度で除した値を0.5W・min/m以上50W・min/m以下の値とする。 - 特許庁
To widen the tolerance regarding the stability of a voltage adjusting mechanism by a method wherein, when a physical quantity is measured by using a vibrator, an applied voltage from a reference voltage source is controlled to be proportional to a digital output signal converted in an analog-to-digital converter.例文帳に追加
振動子を用いて物理量を測定するのに際して、基準電圧源からの印加電圧と、アナログ−デジタル変換器において変換した後のデジタル出力信号とが比例するように制御し、電圧調整機構の安定度に関する裕度を広げる。 - 特許庁
A gate voltage of the MOS-FET 350 is controlled by an operation amplifier 370, and the control is performed by comparison between a potential S appearing on one end of the current detection resistance 360 and a potential T of a reference power source 380, and thereby a constant-current circuit is formed.例文帳に追加
そして、MOS−FET350のゲート電圧をオペアンプ370で制御し、その制御を電流検出抵抗360の一端に現れる電位Sと、基準電源380の電位Tとの比較により行うことで、定電流回路を形成した。 - 特許庁
Connection control parts 110, 120 are controlled by write control circuits 130, 135, connect one write current control line to power source voltage Vcc, while connect the other write current control line to ground voltage GND, in accordance with write data DIN.例文帳に追加
接続制御部110,120は、書込制御回路130,135により制御されて、書込データDINに応じて、一方の書込電流制御線を電源電圧Vccと接続する一方で、他方の書込電流制御線を接地電圧GNDと接続する。 - 特許庁
Using a hydraulic control valve means (solenoid valve SI and SD), the output hydraulic pressure of a power hydraulic source PW is controlled in accordance with the operation of a brake pedal BP and supplied to each wheel cylinder WC (solenoid valve SC1 to be put in close position and another SC2 put in the open position).例文帳に追加
パワー液圧源PWの出力液圧を、液圧制御弁手段(電磁弁SI,SD)によってブレーキペダルBPの操作に応じて制御してホイールシリンダWCに供給する(電磁弁SC1は閉位置とし、電磁弁SC2は開位置とする)。 - 特許庁
This signal processor can constitute a network by being connected to the plural pieces of the external equipment, and in the operation standby state of the device, in the case of detecting connection with the external equipment at least, the shutdown of a power source is controlled and the bus reset of the network is limited.例文帳に追加
複数の外部機器と接続してネットワークを構成し得る信号処理装置であって、装置の作動待機状態において、少なくとも外部機器との接続が検出された場合には電源のシャットダウンを規制し、ネットワークのバスリセットが制限される。 - 特許庁
The operation of the mobile phone can be controlled for e.g., silent mode suppressing the generation of ringtones, radio wave suppression mode suppressing transmission of radio waves, automatic answering mode automatically answering a call in call arrival, and power-off mode turning off a power source.例文帳に追加
携帯電話機の動作制御は、例えば着信音の発生を抑止するマナーモード、電波の送信を抑止する電波抑止モード、着信時に自動的に応答する自動応答モード、または電源を遮断する電源遮断モードに対するものとすることができる。 - 特許庁
To uses an AC input as a commercial power source in a positive-negative symmetrically state, when respective heat generating bodies are controlled independently and to reduce flickers in an image forming apparatus, having an on-demand fixing unit having a plurality of independently controllable heat generating bodies.例文帳に追加
独立に制御が可能な複数の発熱体を持つオンデマンド定着装置を持つ画像形成装置において、各発熱体を独立に制御する場合に商用電源であるAC入力を正負対称に使用すると共に、フリッカを低減させる。 - 特許庁
By the action of the switching circuit 2b controlled by the control circuit 4, a high voltage output to be charged between the electrodes of the radical generator 3 from the high voltage pulse power source 2 is converted to an intermittent high voltage pulse output of highly frequently repeating pulse generation and pulse suspension.例文帳に追加
制御回路4の制御で、スイッチング回路2bの動作により、高電圧パルス電源2からラジカル発生器3の電極間に供給する高電圧出力を、高繰り返しパルスの発生とパルスの休止がある間欠高電圧パルス出力にする。 - 特許庁
While it is light, only H level voltage is outputted from the OR circuit 2 through the voltage comparator 3 by the electromotive force of the LED 6, and the relay circuit 5 is controlled to be transferred to (1) side and not to be connected to the power source 7.例文帳に追加
明るいときには、前記LED6による起電力により電圧比較器3を介して前記OR回路2からHレベル電圧のみが出力され、前記リレー回路5は▲1▼側に変換され且つ電源7には接続されないように制御されること。 - 特許庁
The dielectrics have electrode members 24, 25 respectively arranged to be put inside; the electrode members of a plurality of plasma rector cells are connected to lead line members 261, 262; and a high voltage controlled by a power source supplying device is supplied to the electrodes through a high voltage plug 40.例文帳に追加
前記誘電体には電極部材24,25が挟設され、複数個のプラズマ反応器セルの電極部材はリードライン部材261,262に連結され、電源供給装置で制御される高電圧が高電圧プラグ40を通して電極部材に供給される。 - 特許庁
To provide a delay locked loop (DLL) circuit which can control the operation of a register controlled DLL circuit by detecting whether or not a phase difference between an input source clock REFCLK and an output delay locked clock DLLCLK reaches a maximum value.例文帳に追加
入力されるソースクロックREFCLKと、出力される遅延固定クロックDLLCLKとの間の位相差が最大値に達するか否かを検知し、レジスタ制御型遅延固定ループ回路の動作を制御することができる遅延固定ループ回路を提供する。 - 特許庁
An operation of floating charged particles and an operation of dispersing charged particles in a liquid crystal layer are controlled by determining strengths of electric fields to be applied to a liquid crystal element in accordance with a state of irradiation of light from a light source of a liquid crystal display device.例文帳に追加
液晶表示装置の光源の照射状態に応じて、液晶素子に対して、印加する電界の強度を決定することにより、荷電性粒子を液晶層内で浮遊させたり拡散させたりする動作を制御することができるようになる。 - 特許庁
The synchronous detection light is converted into a clock for control by a synchronous clock generating means 3, inputted into a scanning end timing control means 4 and a scanning start timing means 5, and a light source drive control part A61 is controlled by these output signals STP and STA.例文帳に追加
同期検出光は、同期クロック生成手段3により制御用のクロックに変換されて走査終了タイミング制御手段4と走査開始タイミング手段5に入力され、それらの出力信号STP,STA により光源駆動制御部A61が制御される。 - 特許庁
To make the effective use of existing appliances, without discarding them as well as improving reliability, when the driving source of a servo- cylinder mounted on a continuous casting machine is changed from a stepping motor into a synchronous servo motor, which is controlled in close-loop manner.例文帳に追加
連鋳機に設置されたサーボシリンダの駆動源をステッピングモータからクローズループ制御される同期型サーボモータに変更する際に、その変更作業を既存の機器を廃棄することなく有効利用しながら行い、同時に信頼性の向上も実現すること。 - 特許庁
When the emission current reaches the set value, the switch 70 grounds the cold cathode 35 through the resistance 51 and the gate voltage of the gate power source 41 is so controlled by the gate voltage control circuit 60 so that the emission current is held at the set value.例文帳に追加
そして、エミッション電流が設定値に達したときには、切替器70により冷陰極35が抵抗51を介さずに接地され、エミッション電流が設定値に保持されるようにゲート電源41のゲート電圧がゲート電圧制御回路60により制御される。 - 特許庁
The controller 20 receives such a message that the operation of a motor is permitted and approved and permits electric power to be supplied to a drive source for driving the robot when the robot individual ID coincides with the robot individual ID (identification information) of the robot to be controlled by the controller 20.例文帳に追加
コントローラ20は、送信されたロボット個体別IDが、該コントローラ20が制御するロボットのロボット個体別ID(識別情報)と一致する場合に、該ロボットを駆動する駆動源の電力供給をモータ運転許可承認メッセージにて許可する。 - 特許庁
By controlling a height of the density in the pulse-number modulation, conduction/non-conduction of a transistor Q2 is changed over in high speed to control luminance of an LED 10 in multiple steps, thereby luminance of the surface of a backlight unit with the LED 10 as a light source is controlled in multiple steps.例文帳に追加
パルス密度変調における密度の高低を制御することで、トランジスタQ2の導通/非導通を高速に切り替えてLED10の輝度を多段階制御し、もってLED10を光源とするバックライトユニットの表面の輝度を多段階制御する。 - 特許庁
The electrosurgical device is used with an electrosurgical unit comprising a radio-frequency (RF) power source and a pump, with the throughput of fluid expelled by the pump controlled by the RF power level setting and fluid flow rate setting.例文帳に追加
本発明の電気手術装置は、電気手術ユニットとともに使用され、この電気手術ユニットは、高周波(RF)電源とポンプとを有し、ポンプにより放出される流体は、RF電力の設定および流体流量の設定によって制御される。 - 特許庁
A mobile station MS receives data transmission notice from a base station BS, and performs change so that the transmission power of UL DPCH transmitted by a local station is controlled according to only a TPC signal transmitted by the base station BS of a packet transmission source (a3).例文帳に追加
移動局MSは基地局BSからのデータ送信予告の受信後、パケット送信元の基地局BSが送信するTPC信号のみにしたがって自局が送信するUL DPCHの送信電力の制御を行うように切替える(a3)。 - 特許庁
A gate selection control circuit 60, based on the temperature data received from thermistors 31, 32 to 3n, detects a FET of low temperature, and allows a gate bias voltage of the FET to be controlled so that more power source current flows the FET through a gate selection circuit 50.例文帳に追加
ゲート選択制御回路60は、サーミスタ31,32,〜,3nから受け取った温度データに基づき、温度の低いFETを検出し、ゲート選択回路50を介してそのFETにより多くの電源電流が流れるように、そのFETのゲートバイアス電圧を調節させる。 - 特許庁
When the component is compressed on the substrate to be mounted, air pressure, supplied from a positive pressure supply source 25 to a bellofram 26 abutting against the upper end of a spline shaft 31 to act downward load, is controlled by a control section 40 according to component types.例文帳に追加
搭載時に電子部品を基板に対して押圧する際には、スプライン軸31の上端部に当接し下向きの荷重を作用させるベロフラム26へ正圧供給源25への空圧の圧力を、電子部品の種類に応じて制御部40により制御する。 - 特許庁
When the directional patterns are controlled for achieving various kinds of processing such as sound source separation and speech recognition; a calibration signal for sensitivity adjustment is inputted into a plurality of microphones 41, 42, and the output signals are used for creating information for calibration.例文帳に追加
音源分離や音声認識等の各種処理を実現するための指向特性制御を行うにあたり、複数のマイクロフォン41,42に感度調整用の校正信号を入力し、これらの出力信号を用いて校正用情報を作成しておく。 - 特許庁
Inputted voltage from a commercial AC power source is detected and an on/off signal to be supplied to a switching element SW1 is controlled so that terminal voltage Vc of the input capacitor C1 is proportionated to a peak value Vp of the inputted voltage based on a detected result by this power- factor improving circuit.例文帳に追加
商用交流電源からの入力電圧を検出し、この検出結果を基に入力コンデンサC1の端子電圧Vcが入力電圧のピーク値Vpに比例するようにスイッチング素子SW1に供給されるオン/オフ信号を制御する。 - 特許庁
In this aluminum alloy sheet for heat shield in which either aluminum alloy base face is functioned as a heat shield face to a heat source, and the other aluminum alloy base face is functioned as a thermal radiation face, the emissivity ε of the heat shield face is controlled to the range of 0.01 to 0.20.例文帳に追加
一方のアルミニウム合金素地面を熱源に対する遮熱面として機能させ、他方のアルミニウム合金素地面を放熱面として機能させる遮熱用アルミニウム合金板の、前記遮熱面の放射率εを0.01〜0.20の範囲としたことである。 - 特許庁
A voltage converter circuit 3 converting a direct current power source voltage to a substantially constant voltage is provided in the preceding stage of the series connection of the resistor R1 and the zener diode ZD, and the voltage converter circuit 3 is feedback-controlled depending on operating conditions of the LED(LD).例文帳に追加
抵抗器R1及びツェナーダイオードZDの直列接続の前段に直流電源電圧を略一定に変換する電圧変換回路3を設け、同電圧変換回路3を前記LED(LD)の動作状態に応じてフィードバック制御する。 - 特許庁
To drive a plurality of motors by controlling a plurality of inverter circuits by a control means, to freely control the number of rotation regardless of the frequency of an electric power source and to realize downsizing and low price in a washing and drying machine in which each process of washing, rinsing, dehydrating and drying is controlled.例文帳に追加
洗い、すすぎ、脱水、乾燥の各行程を制御する洗濯乾燥機において、1つの制御手段で複数のインバータ回路を制御して複数のモータを駆動し、電源の周波数に関係なく回転数を自在に制御し、小型、低価格を実現する。 - 特許庁
A musical tone control section of the electronic keyboard musical instrument detects an initial touch by counting a time period from when an on-off sensor 8_1 turns on, to when an on-off sensor 8_2 turns on, and makes a sound source section start producing musical tone in which volume etc. at sound production start time is controlled.例文帳に追加
電子鍵盤楽器の楽音制御部は、オンオフセンサ8_1がオンになった後、オンオフセンサ8_2がオンになるまでの時間を計数することにより、イニシアルタッチを検出し、音源部に対し、発音開始時の音量等が制御された楽音を発音開始させる。 - 特許庁
To provide a semiconductor device in which internal power source voltage can be changed in accordance with an operation frequency and current consumption in a low frequency region of the operation frequency can be effectively controlled while keeping relative timing relation of each signal.例文帳に追加
各信号の相対的なタイミング関係を維持しながら、動作周波数に応じて内部の電源電圧を変更することができ、動作周波数が低い領域での消費電流を有効に抑制することが可能な半導体装置を提供すること。 - 特許庁
The remote controlled breaker includes the main contact turned off at the occurrence of an abnormal current and turned on/off by manual operation, and a relay contact series-connected to the main contact in a feeder line from a power source to a load and turned on/off by a control signal from the outside.例文帳に追加
異常電流の発生時にオフされるとともに手動操作によってオンオフされる主接点と、電源から負荷への給電路において主接点と直列に接続され外部からの制御信号によってオンオフされるリレー接点とを備える。 - 特許庁
The hydraulic pressure of the power source including a pump and an accumulator is controlled to generate booster pressure in a booster chamber of a master cylinder with a hydraulic booster, pedaling force is boosted up thereby and a rear wheel brake is actuated, and a front wheel brake is actuated by the hydraulic pressure generated in a pressurization chamber of the master cylinder.例文帳に追加
液圧ブースタ付マスタシリンダのブースタ圧室にポンプ,アキュムレータを含む動力液圧源の液圧を制御してブースタ圧を発生させ、踏力を倍力するとともに後輪ブレーキを作動させ、マスタシリンダの加圧室に発生した液圧により前輪ブレーキを作動させる。 - 特許庁
An alternator and a driving power source of the electric power steering device are directly connected, a switch is provided between the alternator and a battery, and opening and closing of the switch is controlled by a switch drive control means on the basis of predetermined information.例文帳に追加
オルタネータと前記電動パワーステアリング装置の駆動電源とを直結するとともに、前記オルタネータとバッテリーとの間に開閉器を設け、スイッチ駆動制御手段により所定の情報に基づいて該開閉器の開閉制御を行うことによって達成される。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|