| 意味 | 例文 |
current-sourceの部分一致の例文一覧と使い方
該当件数 : 7159件
Also, this power source circuit is provided with a current detecting circuit 4 connected with the regulator circuit 2 for detecting currents outputted from the regulator circuit 2 and a clock control circuit 3 for controlling the supply of a clock signal to the Haber circuit 1 based on a signal outputted from the current detecting circuit 4.例文帳に追加
また、レギュレータ回路2に接続されレギュレータ回路2から出力された電流を検出する電流検出回路4と、電流検出回路4から出力された信号に基づきハーバー回路1へのクロック信号の供給を制御するクロック制御回路3が設けられている。 - 特許庁
The adjusting terminal 10 for adjusting the current flowing to the current source of an amplifier circuit 5 from the outside is provided, and by connecting a resistor R4 matched with desired output strength between the adjusting terminal 10 and the ground, the output strength is adjusted.例文帳に追加
増幅回路5の電流源に流れる電流を外部から調整するための調整端子10を備え、この調整端子10とアースとの間に所望の出力強度に合わせた抵抗R4を接続することにより、その出力強度が調整できるようになっている。 - 特許庁
To shorten time required to make the temperature of a fixing roller attain fixing feasible temperature by supplying power to a second fixing heater from an auxiliary power source even in a period when a rush current flows without necessitating a special mechanism such as a rush current prevention circuit.例文帳に追加
突入電流防止回路のような特別な機構を必要とすることなく、突入電流が流れる期間であっても、補助電源から第2定着ヒータに電力を供給できるようにし、定着ローラを定着可能温度まで到達させるために必要な時間を短縮する。 - 特許庁
The arithmetic calculation part 21 refers to a junction temperature conversion table stored in a conversion table storage part 20 according to the voltage for measurement V from the arithmetic calculation part 15 and a driving current I from a driving current detection part 19, and calculates the junction temperature of the light source (LED).例文帳に追加
ジャンクション温度演算部21は、演算部15からの計測用電圧V、および駆動電流検出部19からの駆動電流Iに従って、換算表記憶部20に記憶されている、ジャンクション温度換算テーブルを参照し、光源(LED)のジャンクション温度を算出する。 - 特許庁
Transistors(TRs) Q1 and Q2 in diode connection connect with each other in series between two current sources I1, I2 of this peak detection circuit and a capacitor C1 (C2) that detects a ± peak of an input signal Vin connects in parallel with the current source I1 (I2).例文帳に追加
このピーク検出回路は、2つの電流源I1と電流源I2との間に、ダイオード接続されたトランジスタQ1とトランジスタQ2とが直列に接続され、かつ、電流源I1、I2には、入力信号V_inの±のピーク値を検出するコンデンサC1、C2が並列に接続されている。 - 特許庁
The control circuit 4 comprises a connecting terminal 13 to which a capacity C is connected, a constant current source 6 that feeds a charge current to the capacitor C, a buffer 17 that inputs a charge voltage of the capacity C, and voltage dividing resistors R that divide output voltages of the buffer 17.例文帳に追加
制御回路4は、容量Cが接続される接続端子13と、容量Cに充電電流を供給するための定電流源6と、容量Cの充電電圧を入力するバッファ17と、バッファ17の出力電圧を分圧する分圧抵抗Rとを備える。 - 特許庁
In a feedback control system 121 for fixing the light receiving quantity, the outgoing light quantity of the light source 101 is controlled so that the sum of an A-phase direct current component and a B-phase direct current component determined by a light-receiving quantity detection circuit 105 becomes equal to a light-receiving quantity instruction value set beforehand.例文帳に追加
受光量を一定にするフィードバック制御系121では、受光量検出回路105にて求めたA相直流成分とB相直流成分の和が予め設定した受光量指令値と等しくなるように光源101の出射光量が制御される。 - 特許庁
A computer device 1 is incorporated with a current/voltmeter 21 in a socket box 2 which supplies a power source, and an automatic operation controller 3 is provided with a function which detects the abnormality of a current value or voltage value in the socket box 2 for detecting the generation of any failure, and notifies a maintenance staff of the generation of the failure.例文帳に追加
コンピュータ装置1に電源を供給しているコンセントボックス2内に電流/電圧計21を内蔵し、自動運転制御装置3にてコンセントボックス2内の電流値または電圧値の異常を検出する機能を有することで障害発生を検知し、保守員に通知する。 - 特許庁
When a high frequency current is fed to the primary feeder 2 by a high frequency power source 1, an induced electromotive force in the secondary winding 3s of a power feeder transformer 3 is converted into a direct current in a rectificatier 5, controlled to a constant voltage in a constant voltage control part 6 and supplied to a load 7.例文帳に追加
高周波電源1により1次給電線2に高周波電流を流すと、給電トランス3の2次巻線3sに発生した誘導起電力が整流部5で直流に変換され、定電圧制御部6で定電圧に制御されて負荷7に供給される。 - 特許庁
When determining the potential Vm in the memory 114, the potential decision current Ia is recovered, so that a voltage drop due to substrate bias effects incurred in a source line 309a just corresponds to the potential decision current Ia, thereby reducing effects of substrate bias effects and preventing shading increase.例文帳に追加
記憶部114の電位Vmが確定する際には、電位確定用電流Iaに戻っているので、ソース線309aに生じる基板バイアス効果による電圧降下は、電位確定用電流Iaによる分だけであり基板バイアス効果の影響を低減しシェーディング増加を防止する。 - 特許庁
The vehicular lamp includes LEDs 6, 7, 8 connected in series, a cooling fan 5 connected in series with the LEDs 6, 7, 8 for cooling the LEDs 6, 7, 8, and a current supply circuit 4 receiving power supplied from a power source and supplying current to the LEDs 6, 7, 8 and the cooling fan 5.例文帳に追加
直列接続されたLED6,7,8と、LED6,7,8と直列接続され、LED6,7,8を冷却する冷却用ファン5と、電源から供給される電力を受け、LED6,7,8と冷却用ファン5に電流を供給する電流供給回路4とを備える。 - 特許庁
An I/V converter 61, A/D converter 62, CPU 63, D/A converter 64, filament current control circuit 65, main filament current setting device 66, and an electronic circuit 6 including a memory 67 are connected to an objective aperture 18 and a heating power source 15 of a filament 11a.例文帳に追加
対物アパーチャー18とフィラメント11aの加熱電源15には、I/V変換器61、A/D変換器62、CPU63、D/A変換器64、フィラメント電流制御回路65、主フィラメント電流設定器66、メモリ67を含む電子回路6が接続されている。 - 特許庁
A VI conversion circuit 40n receives a voltage signal outputted from a hold circuit 30n, converts the received voltage signal into a current signal on the basis of the resistance of a resistor element R_40 and provides the output of the current signal from a source terminal of a MOS transistor(TR) T_40.例文帳に追加
VI変換回路40_nは、ホールド回路30_nより出力された電圧信号を入力して、この入力した電圧信号を抵抗素子R_40の抵抗値に基づいて電流信号に変換して、この電流信号をMOSトランジスタT_40のソース端子より出力する。 - 特許庁
The test control voltage signal TC flows through resistors R1 and R2 when the NPN transistor Q0 is turned on, the operation of a voltage controlled oscillator V1 and a buffer B10 is stopped because the current from a current source I1 is not supplied, and the output impedance of the buffer B10 becomes high.例文帳に追加
テスト制御電圧信号TCは、抵抗R1、R2を流れ、NPNトランジスタQ0がオンとなることで、電圧制御発振器V1およびバッファB10は、電流源I1からの電流が供給されず動作を停止し、バッファB10の出力インピーダンスは高くなる。 - 特許庁
When an LED 1 for irradiation is driven for blinking or driven for lighting at a constant current pulse, an emitter current flowing in a pair of emitter coupling transistor circuits 5a, 5b is controlled at a voltage V11 applied from a DC control source 6a to a base terminal of a transistor Q5 with a high impedance.例文帳に追加
照明用LED1を定電流パルスで点滅駆動又は点灯駆動させるにあたり、一対のエミッタ結合トランジスタ回路5a、5bに流れるエミッタ電流を、DC制御源6aから高インピーダンスのトランジスタQ5のベース端子に印加される電圧V11で制御する。 - 特許庁
To provide an apparatus for evaluating output characteristic of a solar battery and a method therefor, for accurately measuring an open voltage Voc by applying a forward bias current with minimum power consumption without need of a bipolar power source discharging a large current becoming a factor of cost increase.例文帳に追加
高コスト化の要因となる大電流を吐き出すバイポーラ電源を必要とせず、最小限の消費電力で順バイアス電流を印加することで開放電圧Vocを正確に測定することができる太陽電池出力特性評価装置およびその方法を提供する。 - 特許庁
An electric cord which collects a direct-current electric power 4 generated from the fuel cell electric vehicle group 3, and a wiring 13 which supplies the collected direct-current electric power 4 to a commercial power source 9 or a load 12 through a control/surveillance center 5 which has a linking inverter 6 are equipped.例文帳に追加
燃料電池自動車群3から発電された直流電力4を収集する電気コードと、収集した直流電力4を、連系インバータ6を有する制御・監視センタ5を介して商用電源9または負荷12に供給する配線13を有する。 - 特許庁
This audio amplifier device includes an audio amplifier section 1 as a class D amplifier and a power supply section 2 which controls a source voltage to a current amplification section 12 so that a peak value of the output voltage of a pulse-modulated signal of a current amplification section 12 in the audio amplifier section 1 is as constant as possible.例文帳に追加
このオーディオアンプ装置は、Dクラスアンプとしてのオーディオアンプ部1と、オーディオアンプ部1における電流増幅部12のパルス変調された信号の出力電圧のピーク値を一定に近づけるように電流増幅部12への電源電圧を制御する電源部2とを備える。 - 特許庁
Since the output current error due to the variance in the manufacturing process of the constant current source 11e composed of the first and second MOSFETs 11f, 11g can be averaged by the third resistor 11k, the INL and DNL characteristics of the DA converter can be enhanced.例文帳に追加
このため、第1のMOSFET11fと第2のMOSFET11gから構成される定電流源11eのプロセスばらつきによる出力電流値誤差を第3の抵抗器11kにより平均化することができるため、INL特性とDNL特性を向上させることができる。 - 特許庁
This device is for supplying the current I of a high frequency supplied from a high frequency power source 10 to heating coils 3A and 3B and induction-heating a beverage can 2 rotated by a prescribed rotation number in a peripheral direction by an induction current generated at the heating coils 3A and 3B.例文帳に追加
高周波電源10から供給される高周波の電流Iを加熱コイル3A、3Bに供給し、加熱コイル3A、3Bに発生する誘導電流により、周方向に所定回転数で回転する飲料缶2を誘導加熱するための装置である。 - 特許庁
To provide an LED lighting device capable of preventing LEDs from damage, capable of using not only direct-current voltage but also alternate-current voltage as a supply voltage source, and capable of normally operating the LEDs even if a user links them with polarities of their supply voltage in reverse.例文帳に追加
LEDが損傷することを防止することができ、直流電圧のみならず交流電圧を供給電圧源として使用することができ、使用者が供給電圧の極性を反対に連結してもLEDを正常動作させることができるLED照明装置を提供する。 - 特許庁
A predetermined buffer circuit in a power source circuit comprises a first output circuit in which driving capability of the output current to the higher level side is large and a second output circuit in which driving capability of the output current to the lower level side is large, in which the same output voltages are always generated.例文帳に追加
電源回路のうちの所定のバッファ回路は、同じ出力電圧を常時発生させるようにした、高レベル側への出力電流の駆動能力が大きい第1出力回路と低レベル側への出力電流の駆動能力が大きい第2出力回路とを有する。 - 特許庁
The following problem is solved, that the capacity of a MOS capacitance is elicited in a transition stage when an input bit value changes to suppress a rapid voltage drop in a constant current circuit to make voltage V_DS between the drain and the source of a MOS transistor constituting the constant current circuit falls below overdrive voltage.例文帳に追加
入力ビット値が切り換わる過渡期においてはMOSキャパシタンスの容量が顕在化して定電流回路における急激な電圧降下を抑制し、定電流回路を構成するMOSトランジスタのドレイン・ソース間電圧V_DSがオーバードライブ電圧を下回るという問題を解消する。 - 特許庁
Light beams A1 emitted from each light source are transmitted through each of optical current sensors 4-1 to 4-3 via each of optical fibers 2-1 to 2-3 and supplied to a multiplexer 6 as optical output signals B1, the polarized surface of which are rotated corresponding to each current of power transmission lines 3-1 to 3-3.例文帳に追加
各光源から出射された光A1は、光ファイバ2−1〜2−3を介して光電流センサ4−1〜4−3内を伝搬し、送電線路3−1〜3−3の導体の電流に応じて光の偏波面が回転した光出力信号B1が合波器6に供給される。 - 特許庁
A socket 1 comprises: a housing 5 which has a pin insertion port 522 into which a terminal pin 22 is inserted; a fluorescent lamp contact piece 4a which conductively contacts with the terminal pin 22 of a straight tube type fluorescent lamp 2; and a direct-current contact piece 4b which conductively contacts with a terminal pin of a direct-current light source device.例文帳に追加
ソケット1は、端子ピン22が挿入されるピン挿入口522を有するハウジング5と、直管型の蛍光灯2の端子ピン22に接触導通する蛍光灯用接触子4aと、直流光源装置の端子ピンに接触導通する直流用接触子4bとを有する。 - 特許庁
A charging control circuit, which connects in series a constant-current charging control system containing a constant current FET 3 and a constant-voltage charging control system containing a constant voltage FET 4, is mounted on a feeding path for charging power from an adaptor 1 for an external charging power source to a secondary battery 2.例文帳に追加
外部充電電源アダプタ1から二次電池2までの充電電力供給経路に、定電流FET3を含む定電流充電制御系と定電圧FET4を含む定電圧充電制御系とを直列接続した充電制御回路を設ける。 - 特許庁
The charging/discharging circuit receives the discharge prevention voltage, supplies the constant current from the current source to a capacitor, stores electrical charge in the capacitor, also receives the instant discharge voltage and discharges the electrical charge stored in the capacitor at inclination regarded to be perpendicular to a time base.例文帳に追加
充放電回路は、放電防止電圧を受けて、電流源からの一定電流をコンデンサに供給させてコンデンサに電荷を蓄積させ、かつ瞬間放電電圧を受けて、コンデンサに蓄積された電荷を時間軸に対し垂直とみなせる傾きで放電させる。 - 特許庁
Further, the current of a transfer source of the current mirror circuit varies with an input (Vramp) reflecting an output level instruction signal and a high frequency signal desirably amplified is given while a prescribed bias voltage is given to the control terminal of a lower side transistor (Q1).例文帳に追加
そして、カレントミラー回路の転写元の電流を、出力レベル指示信号を反映した入力(Vramp)に応じて変化させるとともに、下側のトランジスタ(Q1)の制御端子には所定のバイアス電圧を与えつつ、増幅したい高周波信号を入力させるようにした。 - 特許庁
To provide an imaging element for supplying a read current to a pixel circuit to read an output potential, that suppresses variation in the operation of a read current source circuit provided to each array of the pixel circuit so as to reduce stripe noise from an imaged image.例文帳に追加
画素回路に読み出し電流を供給して出力電位を読み出す撮像素子において、画素回路のアレイ列毎に備えられる読み出し電流源回路の動作ばらつきを抑制し、撮像した画像から筋状ノイズを減少させる撮像素子を提供する。 - 特許庁
The level shift circuit is provided with a p-channel MOS transistor(TR) M1 1 that configures a current source, n-channel MOS TRs M13, M14 that configure a current mirror, a p-channel MOS TR M12 for logical input and p-channel MOS TRs M15, M16 acting like a voltage limiter to limit the output voltage.例文帳に追加
電流源を構成するp型MOSトランジスタM11と、カレントミラーを構成するn型MOSトランジスタM13,M14と、論理入力するp型MOSトランジスタM12と、出力電圧を制限する電圧リミッタとなるp型MOSトランジスタM15,M16を設ける。 - 特許庁
To provide a protection circuit in an electric power tool having a lithium cell as a power source of a motor, which protection circuit allows an instantaneously excessive current for starting the motor but intercepts an excessive current in locking the motor caused during the use of the electric power tool.例文帳に追加
本発明の課題は、リチウム電池をモータの電源とする電動工具において、モータの起動時に流れる瞬時の過大電流は許容し、電動工具の使用時に生じるモータのロック時の過大電流は遮断し得る保護回路を備えたコードレス電動工具を提供することである。 - 特許庁
Hereby, each current value flowing in a plurality of resisters Rx-y to be measured is measured simultaneously between the power source part EC- and the board connection part MaR-y, and even during a short circuit time of some part Rx-y to be measured, a current value flowing in another part Rx-y to be measured can be measured accurately.例文帳に追加
これにより、電源部EC−と基板接続部MaR−y間で、複数の被測定抵抗Rx−yに流れる電流値を同時に計測し、また、ある被測定部Rx−yの短絡時においても、他の被測定部Rx−yに流れる電流値を正確に計測できる。 - 特許庁
Either a differential amplification circuit composed of two transistors where a resistor and a variable constant current source which specify an output current value are connected and furthermore an emitter is connected in common at the same connection point, or a circuit operating like a Schmidt circuit is used as the output circuit 200.例文帳に追加
出力回路としては、出力電流値を規定する抵抗と可変定電流源とが接続され、更に同じ接続点にエミッタが共通接続された2つのトランジスタで構成される差動増幅回路か、シュミット回路に類似した動作をする回路のいずれかを用いる。 - 特許庁
To provide an anodic oxidation and an electrochemical oxidation method for reducing the intra-plane fluctuation of the characteristics of an electronic device such as an electric field emission type electron source, the electric field emission type electron source having small intra-plane fluctuation of emission current, and a manufacturing method for the same.例文帳に追加
電界放射型電子源のような電子デバイスの特性の面内ばらつきを小さくすることができる陽極酸化方法および電気化学酸化方法、エミッション電流の面内ばらつきが小さい電界放射型電子源およびその製造方法を提供する。 - 特許庁
In the semiconductor device, a switch NMOS transistor NM2 has its drain and source connected between the gate and source of the output NMOS transistor NM1 supplying an output current to a load 12, and also has its gate connected to an internal ground wire line GW connected to a ground terminal GND.例文帳に追加
スイッチ用のNMOSトランジスタNM2は、負荷12に出力電流を供給する出力用のNMOSトランジスタNM1のゲートおよびソース間にそれぞれドレインおよびソースを接続すると共に、接地端子GNDに接続される内部接地配線GWにゲートを接続する。 - 特許庁
To provide an anodic oxidation and an electrochemical oxidation method for reducing the intra-plane fluctuation of the characteristics of an electronic device such as an electric field emission type electron source, the electric field emission type electron source having small intra-plane fluctuation of emission current and insulation tolerance, and a manufacturing method for the same.例文帳に追加
電界放射型電子源のような電子デバイスの特性の面内ばらつきを小さくすることができる陽極酸化方法および電気化学酸化方法、さらには、エミッション電流、絶縁耐圧の面内ばらつきが小さい電界放射型電子源およびその製造方法を提供する。 - 特許庁
This forming device of the electrode for the lithium secondary battery has an Si sputtering source 3 for sputtering Si, for constituting the active material layer on the surface of a collector 1; and a Co-sputtering source 4 for sputtering Co, constituting the active material layer on the surface of the current collector 1.例文帳に追加
このリチウム二次電池用電極の形成装置は、集電体1の表面上に、活物質層を構成するSiをスパッタするためのSiスパッタ源3と、集電体1の表面上に、活物質層を構成するCoをスパッタするためのCoスパッタ源4とを備えている。 - 特許庁
As a result, a conductive path starting from a power source 80 and returning to the power source 80 through the plate electrode 51 and the wiring pattern 121 is formed and it is possible to inspect the continuity of the wiring pattern 121 by measuring the current flowing in the wiring pattern 121.例文帳に追加
このため、電源80からプレート電極51および検査対象配線121を経由して電源80に戻る導電経路が形成され、検査対象配線121を流れる電流を測定することで検査対象配線121の導通を検査することができる。 - 特許庁
In a source follower circuit, sources of first and second NMOS transistors Q7 and Q8 are respectively connected to drains of third and fourth NMOS transistors QA and QB, and a constant current source CS2 is connected to both sources of the third and fourth NMOS transistors QA and QB.例文帳に追加
ソースホロワ回路において、第1および第2のNMOSトランジスタQ7、Q8のそれぞれのソースに第3および第4のNMOSトランジスタQA、QBのドレインが接続され、第3および第4のNMOSトランジスタQA、QBの双方のソースへ定電流源CS2が接続される。 - 特許庁
For the purpose, a current path is formed between a power line 531 and a source signal line 532 in parallel to a drive transistor 539 of each pixel to make small the apparent resistance value of the drive transistor 539, and then the drain-source resistance value of the drive transistor is decreased to reduce the rounding of the waveform.例文帳に追加
そのために各画素の駆動トランジスタの見かけの抵抗値を小さくするため、電源線とソース信号線間に駆動用トランジスタと並列に電流経路を形成することで、駆動用トランジスタのドレイン−ソース間抵抗値を低下させ、波形のなまりを小さくした。 - 特許庁
In the equivalent circuit model of a field effect transistor used for a power converting circuit, the capacitance Cgs between the gate and the source, the capacitance Cgd between the gate and the drain, and the channel current source Ich are extracted from the switching waveform in the inductive load of the field effect transistor.例文帳に追加
電力変換回路に用いられる電界効果型トランジスタの等価回路モデルにおいて、ゲート−ソース間容量Cgs、ゲート−ドレイン間容量Cgd、及びチャネル電流源Ichを、電界効果型トランジスタの誘導性負荷におけるスイッチング波形から抽出する。 - 特許庁
To provide an image-forming apparatus capable of sufficiently removing a residual potential on an image carrier without arranging a new discharge light source other than a neutralization light source arranged between a first transferring position and a cleaning device, and setting a high transfer current.例文帳に追加
本発明は、一次転写位置とクリーニング装置の間に配される除電光源以外に新たに除電光源を設けることなく、さらに、転写電流を高く設定することなく、像担持体上の残留電位を十分に除電可能な画像形成装置を提供することを目的とする。 - 特許庁
In this invention, an output current command value corresponding to a specified brightness command value is used for lighting the light source 31, and the rate of the illuminance of illumination light to be measured in this case to an illuminance standard value depending on the specified brightness command value, namely, the reduction rate of the illuminance of the light source 31 is measured.例文帳に追加
本発明では、ある特定の明るさ指令値に対応する出力電流指令値で光源31を点灯させ、その際に測定される照明光の照度と前記特定の明るさ指令値に応じた照度規格値との比率、すなわち光源31の照度の低下率を測定する。 - 特許庁
This semiconductor device in which current flows in the vertical direction includes a structure that decreases resistance between a source electrode 19 and a drain electrode 20 at a position different from a position (a dotted line X) having highest electric field intensity between the source electrode 19 and the drain electrode 20.例文帳に追加
縦方向に電流を流す半導体装置であって、ソース電極19からドレイン電極20の間の最も高い電界強度となる位置(点線X)とは異なる位置に、ソース電極19からドレイン電極20間の抵抗を低抵抗化させる構造を備えている。 - 特許庁
Due to such a structure, the second thin-film transistor 15 suppresses the quantity of current, and further reduces the probability of shortcircuiting between the source/drain electrode 19 and the gate electrode 21 than that between the source/drain electrode 20 and the gate electrode 21.例文帳に追加
かかる構成により第2薄膜トランジスタ15は、電流量の減少を抑制しつつ、ソース/ドレイン電極19とゲート電極21との間における短絡発生確率を、ソース/ドレイン電極20とゲート電極21との間における短絡発生確率よりも低減している。 - 特許庁
When a filament of a discharge lamp DL equipped with a pair of filament electrodes E1, E2 is broken, the filament break is detected by detecting direct-current voltage between power-source side terminals and/or non-power-source side terminals between the pair of filament electrodes.例文帳に追加
一対のフィラメント電極E1、E2を備えた放電ランプDLのフィラメントが断線したときに一対のフィラメント電極間の電源側端子間および/または非電源側端子間に現れる直流電圧を検出することにより当該フィラメント断線を検知する。 - 特許庁
When the output current of one of source voltages increases, an error voltage correction means 5 corrects the error voltage so that the output voltage decreases, and when the output voltage of the other source voltage decreases, the error voltage correction means 5 corrects the error voltage so that the output voltage increases.例文帳に追加
誤差電圧補正手段は一方の電源電圧の出力電流が増加した場合には、その出力電圧を下げるように誤差電圧に補正を加え、逆に、他方の電源電圧の出力電流が減少した場合、その出力電圧を上げるように誤差電圧に補正を加える。 - 特許庁
The wavelength variable light source 1040 outputs a light whose wavelength depends on the applied wavelength control current, and an optical modulation section 1050 uses the information signal and modulates the light outputted from the wavelength variable light source 1040 to generate/output the optical packet.例文帳に追加
波長可変光源1040は、印加された波長制御電流によって波長を決定された光を出力し、光変調部1050は、情報信号を用いて、波長可変光源1040から出力された光を変調することにより、光パケットを生成・出力する。 - 特許庁
To reduce through current of the transistor output circuit remarkably, to raise/lower an output signal up (down) to power source potential (upper limit value) and ground potential (lower limit value), and to smoothly change the output signal at a part in the vicinity of the power source potential and the ground potential.例文帳に追加
トランジスタ出力回路の貫通電流を著しく低減するとともに、出力信号を電源電位(上限値)及びグランド電位(下限値)まで上昇/低下させ、かつ、出力信号をその電源電位及びグランド電位への近傍では滑らかに変化させる。 - 特許庁
As the shape of an extraction electrode of a transistor which feeds electric current to the heaters for delivering the ink, a collector electrode 107 on the heater connecting side is made thicker as the heater approaches; and an emitter extraction electrode 105, on the power source connecting side is made thicker as the power source approaches so as to reduce the voltage.例文帳に追加
インク吐出用ヒータに電流を供給するトランジスタの引き出し電極の形状を、電圧降下が少なくなるように、ヒーター接続側のコレクタ電極107はヒータに近づくにつれ太くし、又、電源接続側のエミッタ引き出し電極105は電源に近づくにつれ太くする。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|