| 例文 |
maximum averageの部分一致の例文一覧と使い方
該当件数 : 718件
The controller 4-J calculates an average rate of change of the output values within a relative time zone from detection of either one of the maximum value or minimum value to detection of the other.例文帳に追加
制御装置(4−J)は、最大値と最小値との一方を検出してから最大値と最小値との他方を検出するまでの相対時間区間における出力値の平均変化率を算出する。 - 特許庁
The number of numerical data is counted in a set of collected numerical data (step S13), an average value is computed (step S14), a maximum value is selected (step S15), and a minimum value is selected (step S18).例文帳に追加
収集された数値データの集合について、数値データの個数をカウントし(ステップS13)、平均値を算出し(ステップS14)、最大値を選出し(ステップS15)、最小値を選出する(ステップS18)。 - 特許庁
As the cooling roll 5, the roll, in which the maximum eccentric amount of the peripheral surface 53 of the cooling roll 5 accompanied with the rotation of the cooling roll 5 is two times or less the average thickness of the obtained rapidly cooled strip 8, is used.例文帳に追加
冷却ロール5としては、冷却ロール5の回転に伴う冷却ロール5の周面53の最大偏心量が、得られる急冷薄帯8の平均厚さの2倍以下のものを用いる。 - 特許庁
The stretched sheet has a piercing strength of 3 N or more, a porosity of 40 to 90% of the sheet volume, an average hole diameter of 20 to 200 μm, and the maximum hole diameter of 50 to 2000 μm.例文帳に追加
このシートは、突刺強度が3N以上であり、空孔率が40〜90体積%の範囲であり、平均孔径が20〜200μmの範囲であり、最大孔径が50〜2000μmの範囲である。 - 特許庁
A received signal X(i) where the tailing section 43c in the range of T1-T2 is A/D converted is normalized at the maximum value of the X(i), and the average value of the normalized X(i) is furthermore calculated.例文帳に追加
T1〜T2の範囲の尾引き部43cのA/D変換された受信信号X(i)がX(i)の最大値で正規化され、さらに正規化されたX(i)の平均値が算出される。 - 特許庁
The objective steel material has average Mn concentration lower in the central part of the plate thickness than in the whole steel, and maximum Mn concentration at the central part of the plate thickness, of 2.9 mass% or less.例文帳に追加
本発明の鋼材は、板厚中心部の平均Mn濃度が鋼中平均Mn濃度よりも低く、かつ、板厚中心部における最大Mn濃度が2.9質量%以下である。 - 特許庁
Subsequently, one of the average value, the central value, the minimum value and the maximum value of remaining light emission intensity from which the abnormally high emission intensity is deleted is calculated or selected as a read value.例文帳に追加
続いて、異常に高い発光強度を削除された残りの発光強度の平均値、中央値、最小値および最大値のいずれか1つを読取値として算出あるいは選択する。 - 特許庁
A copper or copper alloy material is manufactured, whose surface roughness is ≤0.1 μm in the arithmetic average roughness (Ra) and ≤1 μm in the maximum height (Rz), and on whose surface roll scratches do not exist.例文帳に追加
表面粗さが算術平均粗さ(Ra)で0.1μm以下、かつ最大高さ(Rz)で1μm以下であり、さらに材料表面にロールスクラッチが存在しない銅または銅合金材を製造する。 - 特許庁
(5) The base amount of maximum payment for Allowance for Home Modification for In-Home Long-Term Care as prescribed in the preceding paragraph shall be the amount specified by the Minister of Health, Labour, and Welfare by type of Home Modification after considering the average expenses required. 例文帳に追加
5 前項の居宅介護住宅改修費支給限度基準額は、住宅改修の種類ごとに、通常要する費用を勘案して厚生労働大臣が定める額とする。 - 日本法令外国語訳データベースシステム
A job load management program to be executed by partitions measures actual consumption of processor resources by the logical partitions for prescribed average time intervals of addition and compares the measured actual consumption with the maximum allowable consumption.例文帳に追加
パーティションで実行される仕事負荷管理プログラムは、所定の加算平均時間間隔にわたって論理パーティションによるプロセッサ・リソースの実消費を測定し、それを最大許容消費と比較する。 - 特許庁
This pellicle has a pellicle film whose average thickness is larger than the thickness corresponding to the maximum value of transmittance on the correlation curve of the thickness and transmittance of the pellicle film.例文帳に追加
このペリクルは、ペリクル膜の平均膜厚が、このペリクル膜の膜厚と透過率との相関曲線における透過率極大値に対応する厚さよりも厚く設けられていることを特徴としている。 - 特許庁
A molybdenum material or molybdenum-alloy material having ≤0.1μm center line average roughness Ra of surface and ≤1.0μm maximum height Rz is used for a setter on which titanium or titanium-alloy powder is placed.例文帳に追加
チタン又はチタン合金の粉末を載置するセッターとして、表面の中心線平均粗さRaが0.1μm以下、最大高さRzが1.0μm以下のモリブデン材又はモリブデン合金材を使用する。 - 特許庁
Simultaneously with the detection of peripheral illuminance by an illuminance detection means 7, an image feature detection means 3 detects image features including the average value, maximum value and minimum value of illuminance of an input image.例文帳に追加
照度検出手段7により周囲照度を検出すると同時に、映像特徴検出手段3により入力映像の輝度の平均値、最大値、最小値を含む映像特徴を検出する。 - 特許庁
When a signal is detected at a status 1, it is detected at a status 2 whether or not a maximum correlation value average and code synchronism of the signal received by using an antenna 1 are established.例文帳に追加
状態1において信号を検出すると、状態2において、アンテナ1を利用して受信した信号の最大相関値平均および符号同期が確立しているか否かを検出する。 - 特許庁
A high quality image can be imaged by making the AF focusing time shortest by raising a gain of an average luminance signal to the maximum in an analog signal processing unit 3 when a level of the average luminance signal is low, and by imaging after lowering the gain when the image is to be imaged after performing AF focusing.例文帳に追加
平均輝度信号レベルが低いときには、アナログ信号処理部3にて平均輝度信号の増幅率を最大まで上げることでAF合焦時間を最短とすると共に、AF合焦後に画像を撮像する際には増幅率を下げて撮像することにより、高画質な画像を撮像することが可能となる。 - 特許庁
When the amount of data accumulation with respect to full capacity of the buffer memory 14 exceeds a previously set threshold value, the system controller 17 calculates the average bit rate of the maximum bit rates stored in the buffer memory 15, and acquires the rotation speed by referring to a rotation speed table showing the relationship between the average bit rate and the rotation speed.例文帳に追加
バッファメモリ14の全容量に対するデータ蓄積量が、予め設定された閾値を超えると、システムコントローラ17は、バッファメモリ15に格納された最大ビットレートの平均ビットレートを算出し、この平均ビットレートと回転速度との関係を示す回転速度テーブルを参照して、回転速度を取得する。 - 特許庁
The anatase type titanium dioxide particles comprise titanium dioxide and zirconium oxide and has a zirconium oxide content in a range of 1-30 wt.% and a crystallite diameter in a range of 15-50 nm, wherein an average maximum particle width (W_M) is in a range of 2-50 nm and an average particle length (L) is in a range of 10-500 nm.例文帳に追加
酸化チタンと酸化ジルコニウムとからなり、酸化ジルコニウムの含有量が1〜30重量%の範囲にあり、結晶子径が15〜50nmの範囲にあるアナタース型酸化チタン粒子であって、平均粒子最大幅(W_M)が2〜50nmの範囲にあり、平均粒子長(L)が10〜500nmの範囲にある。 - 特許庁
An average value (average luminance) AVE and a maximum luminance position xCC are computed with respect to a change (integrated luminance) S(I) corresponding to a horizontal position I of an integrated value of luminance values along a vertical direction for every horizontal position I in a horizontal direction in a predetermined object region (mask) OA including an upper part of at least a binarized object OB.例文帳に追加
少なくとも2値化対象物OBの上部を含む所定の対象領域(マスク)OAでの横方向の各横位置I毎での縦方向に沿った輝度値の積算値の横位置Iに応じた変化(積算輝度)S(I)に対し、平均値(平均輝度)AVEと、最大輝度位置xCCとを算出する。 - 特許庁
A control part 4 of a host computer 2 constituting the image reader acquires an average value in the main scanning direction of the transmission densities of all lines of a film image, preserves them as array variables AveR, obtains an average value FilmAveR of all lines and a maximum value AveRMax from the array variables AveR, and further obtains a threshold ThR.例文帳に追加
画像読取装置を構成するホストコンピュータ2の制御部4はフィルム画像の全ラインの透過濃度の主走査方向平均値を取得し、配列変数AveRに保存し、配列変数AveRから全ラインの平均値FilmAveRと最大値AveRMaxを求め、しきい値ThRを求める。 - 特許庁
A receiving antenna group selector 3 calculates an average receiving power for each of the receiving antenna groups 1-1 to 1-M from the receiving powers P_1, P_2, ..., P_M supplied from the power calculators 2-1 to 2-M e.g., at fixed time intervals T and selects a receiving antenna group 1-i with which the average receiving power becomes maximum.例文帳に追加
受信アンテナ群選択部3は、例えば、一定時間T毎に、電力算出部2−1〜2−Mから供給される受信電力P_1、P_2、…、P_Mから、受信アンテナ群1−1〜1−M毎に平均受信電力を計算し、平均受信電力が最大となる受信アンテナ群1−iを選択する。 - 特許庁
On the surface of the body 11, a plurality of concaves and convexes 14 are formed repeatedly, and the plurality of concaves and convexes 14 are formed so that an average value of the maximum dimension of the concaves and convexes 14 in a surface direction on the surface of the body 11 is larger than an average thickness of the Sn plated layer 13.例文帳に追加
本体部の表面11において、複数の凹凸部14が繰り返し形成され、複数の凹凸部14は、本体部の表面11の面方向における凹凸部14の最大寸法の平均値がSnめっき層13の平均厚み寸法よりも大きくなるように形成される。 - 特許庁
In an electrophotographic apparatus which is cleaner-less and adopts the contact one-component development method, and uses toner having a weight average particle diameter of 7μm or less, the surface layer of the electrophotographic photoreceptor has ten-point average surface roughness Rz that is 0.1≤Rz≤1μm and the maximum height that is 0.2≤Ry≤2μm.例文帳に追加
クリーナーレス、接触一成分現像方式、さらに重量平均粒径が7μm以下のトナーを用いた電子写真装置において、感光体表面層の10点平均表面粗さRzが0.1≦Rz≦1μm、最大高さが0.2≦Ry≦2μmであることを特徴とする電子写真感光体。 - 特許庁
First and second recording heads eject a plurality of kinds of ink so that weighted average of recording ratio for each scanning in ink (Lgy) with the highest brightness value in the plurality of the ink becomes maximum, and maximum value of the recording ratio of the ink (Lgy) with the highest brightness value becomes larger than the other ink (Y, M, C, K).例文帳に追加
複数のインクの内の最も明度が高いインク(Lgy)の走査毎の記録比率の加重平均が最も大きくなり、かつ、その最も明度が高いインク(Lgy)の記録比率の最大値が他のインク(Y,M,C,K)よりも大きくなるように、第1および第2記録ヘッドから複数のインクを吐出させる。 - 特許庁
When it is determined that the chemical flow rate maximum value is abnormal, the abnormality detection processing module 6 searches for an address such as a mail address from a database 5b, and transmits the chemical flow rate average value determined as being normal and the chemical flow rate maximum value determined as being abnormal as a detection result by electronic mail, for example.例文帳に追加
薬液流量最大値に異常があると判定した場合、異常検知処理部6は、データベース部5bから、メールアドレスなどの連絡先を検索し、検知結果として、正常と判定された薬液流量平均値、および異常と判定された薬液流量最大値を電子メールなどによって送信する。 - 特許庁
(1) The base contains a blue dye and has a blue density of ≥0.15 and a yellow index of ≤0, or (2) the base has 58-78% average light transmittance in the 500-600 nm region, ≥75% maximum light transmittance in the 400-500 nm region and ≥75% maximum light transmittance in the 600-700 nm region.例文帳に追加
支持体が青色染料を含有し、該支持体の青色濃度が0.15以上、イエローインデックスが0以下である; 500〜600nmの平均光線透過率が58〜78%、かつ400〜500nmの最大光線透過率、600〜700nmの最大光線透過率がいずれも75%以上である支持体。 - 特許庁
In the bonding wire in which a core material 1 composed mainly of copper is subjected to palladium plating 2, a maximum diameter of voids existing in the vicinity of a copper core material interface below a palladium coating layer is 60 nm or less, and the number of voids having a maximum diameter of 10 nm or more which exist per 1 μm of the coating length is 0.6 or less on average.例文帳に追加
銅を主成分とする芯材1にパラジウムめっき2を施したボンディングワイヤであって、パラジウム被覆層下の銅芯材界面近傍に存在するボイドの最大径が60nm以下で、かつ該被膜長さ1μm当りに存在する最大径が10nm以上のボイドの個数が平均0.6個以下であるボンディングワイヤ。 - 特許庁
The first layer has a thickness of about 1% to about 10% of the total thickness of the multilayered film, has a maximum thickness of about 0.25 mil, and has a thickness uniformity deviation of less than about 20% of an average thickness of the first layer.例文帳に追加
第1層は、多層フィルム構造体の総厚の約1%〜約10%であり、約0.25ミルの最大厚さを有し、また、第1層の平均厚さの約20%未満の厚み均一性偏差を有する。 - 特許庁
K is a multiplied value obtained by multiplying a detection ratio in detecting K or the out put voltage vo, a conversion ratio in converting an analogue value to a digital value, and a conversion ratio for converting the effective value or the average value V to the maximum value.例文帳に追加
またKは出力電圧voを検出する際の検出比と、アナログ値をデジタル値に変換する際の変換比と、実効値または平均値Vを最大値に変換するための変換比との乗算値である。 - 特許庁
Parameters such as a minimum value, a maximum value, a mode, a variance, and an average value of the feature quantities are introduced from each histogram and a correction curve with respect to the feature quantities is generated on the basis of the parameters (steps S33, S34).例文帳に追加
各ヒストグラムから特徴量の最小値、最大値、最頻値、分散、平均値等のパラメータを導き出し、パラメータに基づいて特徴量に対する補正曲線を生成する(ステップS33,S34)。 - 特許庁
To provide a heating device and an image forming device enabled to restrain variation of maximum electric power at the time of changing of power supply voltage by retaining an average electric current flowing in a magnetic field generation means constant.例文帳に追加
磁場発生手段に流れる平均電流を一定に保つことにより、電源電圧が変動した際にも最大電力の変動を抑えることを可能とした加熱装置及び画像形成装置を提供する。 - 特許庁
The polyester film for printing and molding has a center line average roughness Ra of 0.1-50 nm on both the surfaces, a maximum roughness Rt of 10-1,000 nm on both the surfaces and a surface orientation factor of 0-0.05.例文帳に追加
フィルム両表面の中心線平均粗さRa0.1〜50nm、かつフィルム両表面の最大粗さRtが10〜1000nmであり、面配向係数が0〜0.05の印刷・成形加工用ポリエステルフィルム。 - 特許庁
A correction information determination part determines correction information for correcting the gradation characteristic about luminance per image on one screen in accordance with combination of the acquired minimum luminance, average luminance, and maximum luminance.例文帳に追加
補正情報決定部は、前記1画面の画像ごとに、取得した前記最小輝度、平均輝度および最大輝度の組み合わせに応じて、前記輝度についての階調特性を補正するための補正情報を決定する。 - 特許庁
To provide a preset type wattmeter allowing power consumption and an electricity use charge to be directly read in digital values, and capable of collecting and grasping power consumption, and of controlling integrated power, the maximum power and the average power by a preset function.例文帳に追加
消費電力や電気使用料金をデジタル値で直読でき、消費電力の収集および把握が可能で、プリセット機能による積算電力、最大電力、平均電力の管理を可能とする。 - 特許庁
An amount of the carbide or the like of which an average particle diameter of the carbide or the like on the skin layer part is set to 3 μm or lower and the minimum diameter/the maximum diameter are 0.6 or higher is set to 70% or higher of the whole amount of the carbide or the like.例文帳に追加
表層部の炭化物等の平均粒径を3μm以下とし、かつ、最小径/最大径の値が0.6以上となる炭化物等の量が、炭化物等の全体量の70%以上であるようにする。 - 特許庁
Furthermore, when the gain and transmission voltage are already maximum, the flow velocity is determined as being zero, if the average of a real part of a Doppler frequency signal is a prescribed reference value or larger; and measurement is decided as being impossible, if it is the reference value or smaller.例文帳に追加
さらに、利得も送信電圧も既に最大の場合、ドップラ周波数信号の実部の平均が所定の基準値以上ならば、流速ゼロと判断し、基準値以下ならば、計測不能と判断する。 - 特許庁
Using information (a product category, a model, and a failure case) received from a client terminal device, an estimate extraction part 2f extracts matching average amount, maximum amount, and minimum amount from the rough estimate database 2b.例文帳に追加
見積額抽出部2fはクライアント端末装置から受信する情報(製品カテゴリ、型式、故障の症状)を利用して概算見積データベース2bから対応する平均額と最低額と最高額とを抽出する。 - 特許庁
To precisely and stable machine depressions having a smallest possible difference between an average depth and the maximum depth in the periphery faces of cooling drums for a double-drum continuously casting device with shot blasting.例文帳に追加
双ドラム式連続鋳造装置の冷却ドラム周面にショットブラスト法によって窪みを加工する場合に、窪みの平均深さと最大深さの差ができるだけ小さい窪みを精度よく安定して加工する。 - 特許庁
This ceramic substrate 7 densifies the surface layer part of the ceramic substrate 7 and makes the average value of the maximum width of an air hole 9 on the surface layer part smaller than that of the air hole 10 on the inner layer surface.例文帳に追加
本発明のセラミックス基板7は、セラミックス基板7の表層部を緻密にし、表層部における気孔9の最大幅の平均値を、内層部における気孔10の最大幅の平均値よりも小さくする。 - 特許庁
To solve the following problem: when trade instruction information for Nikkei futures or the like is output by a computer on the basis of the information on change in only the previous day's Dow Jones industrial average, maximum drawdown increases or desired result cannot be obtained.例文帳に追加
コンピュータで日経先物等の売買指示情報を出力するのに、前日ダウジョーンズ工業平均だけの変化情報で決定すると、最大ドローダウンが大きくなるなど、取引の成績がよくならない。 - 特許庁
A single crystal sapphire substrate is the substrate for epitaxial growth, where the arithmetic average surface roughness Ra of a main surface is 0.0002 to 0.001 μm and the maximum height Rmax of the main surface is not more than 0.1 μm.例文帳に追加
エピタキシャル成長用の単結晶サファイア基板であって、主面の算術平均表面粗さRaが0.0002〜0.001μmであり、上記主面の最大高さRmaxが0.1μm以下であること。 - 特許庁
Average value for every period or a maximum value of motor currents or motor torque generated in the acceleration or deceleration period, and the constant speed operation period of an induction motor 17 is switched and displayed for a specified time.例文帳に追加
誘導電動機17の加減速運転期間と一定速度運転期間で発生する電動機電流または電動機トルクの前記各期間ごとの平均値または最大値を、切り換えて所定時間表示する。 - 特許庁
The low illumination intensity has 1-20,000 luxes, preferably 1,000-5,000 luxes represented by the maximum illumination intensity in a cultivation period and about 50-3,000 luxes represented by an average illumination intensity in the period.例文帳に追加
ここで、低照度とは、栽培期間の最大照度で表せば1〜20000ルクス、好ましくは1000〜5000ルクスの範囲内であり、明期の平均照度で表せば50〜3000ルクス程度の照度である。 - 特許庁
The residual compressive stress in the direction of the maximum principal stress in the surface of the workpiece can be selectively increased by setting the average number of irradiation of pulse laser beams at the same point to be at least two.例文帳に追加
ここで、同一点におけるパルスレーザビームの照射回数の平均値を2回以上とすることで、被加工材表面における最大主応力の方向の残留圧縮応力を選択的に高めることができる。 - 特許庁
A line length determining unit 16 calculates the maximum value or average value of the length of a line of cars waiting at a stoplight on each lane, and determines whether or not the line length of all the lanes calculated is longer than a certain length.例文帳に追加
行列長判定部16は、車線毎の信号待ち行列の行列長の最大値又は平均値などを算出し、算出した全車線の行列長が所定長より長いか否かを判定する。 - 特許庁
Based on the data obtained by the GPS circuit 32, CPU 30 collects record data including the change in altitude, average slope angle, and maximum slope angle, and the data is displayed on the display 14 or stored in the memory 34.例文帳に追加
CPU30は、GPS回路部32により得られたデータに基づいて、標高変化推移、平均斜度、最大斜度等の各記録データを求め、記録データを表示部14に表示させ、或いはメモリ34に格納する。 - 特許庁
The developing roller is designed so that a difference between the maximum value and the minimum value of elastic layer thickness of the developing roller cross-section is 0.125% or less of the outer diameter average value of the conductive multilayer roller and the number of protrusions on the outer diameter shape is one or two.例文帳に追加
現像ローラ断面の弾性層厚さの最大値と最小値の差が、該導電性多層ローラの外径平均値の0.125%以下でかつ、外径形状の凸部が1、あるいは2つである現像ローラ。 - 特許庁
The air filter material formed by stacking an air flow-in layer and an air flow-out layer has an average flow rate fine pore diameter of 20-40 μm, a minimum fine pore diameter of 2.4-3.8 μm and a maximum fine diameter of 80 μm or less.例文帳に追加
空気流入層と空気流出層とが積層されてなるエアフィルタ材料は、平均流量細孔径が20〜40μm、最小細孔径が2.4〜3.8μm及び最大細孔径が80μm以下である。 - 特許庁
To solve the problem that the power consumption of an operational amplifier is increased since it is necessary to secure a wide dynamic range of the operational amplifier of an OFDM (Orthogonal Frequency Division Multiplexing) receiver if there is a great difference between a maximum amplitude value of an OFDM signal and an average amplitude value.例文帳に追加
OFDM信号の最大振幅値と平均振幅値の差が大きいとOFDM受信機のオペアンプのダイナミックレンジを大きくとる必要があり、オペアンプの消費電力が大きくなる。 - 特許庁
The body part is provided with an effective illumination area on the almost center position of the rectangle and an irregular structure 12 for which the maximum value of center line average roughness is 3 to 1,000 μm is formed in a range including the area.例文帳に追加
本体部は、長方形の略中央位置に有効照明領域が設けられ、この領域を含む範囲に中心線平均粗さの最大値が3〜1000μmの凹凸構造12が形成される。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
| ※この記事は「日本法令外国語訳データベースシステム」の2010年9月現在の情報を転載しております。 |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|
