| 例文 |
difference valueの部分一致の例文一覧と使い方
該当件数 : 7193件
Transfer functions of the impedance and a low-pass filter obtained by the nominal values of the inductance L and the resistance R are multiplied by a difference between the charge current Ib^ and a charge-current detected value Ibdet that actually flows to the secondary battery, and the charge-voltage command value Em* is calculated based on the result of the multiplication.例文帳に追加
そして充電電流Ib^と、実際に二次電池に流れた充電電流検出値Ibdetの偏差に対して、インダクタンスLと抵抗Rのノミナル値によるインピーダンスとローパスフィルタの伝達関数を乗じ、その結果に基づいて、充電電圧指令値Em^*を算出する。 - 特許庁
The distance arithmetic section 4 determines, at a predetermined integration time, an integration value of difference of special phase interval synchronizing with the modulating signal so as to offset the fluctuation component of environmental light components received by the photo detecting element 1, and determines the distance to the object Ob using the integration value.例文帳に追加
距離演算部4は、光検出素子1が受光する環境光成分のうち変動成分を相殺するように変調信号に同期する特定の位相区間の差分の積算値を所定の積分時間において求め、当該積算値を用いて物体Obまでの距離を求める。 - 特許庁
In the operational amplifier, when a voltage V_in of the input signal is high or changes rapidly and a voltage difference |V_out-V_in| of the absolute value between the input signal and an output signal exceeds a setting value V_F, the switch control circuit 22 of a constant current circuit 12 turns on a switch 20.例文帳に追加
この演算増幅器において、入力信号の電圧V_inが大きく、あるいは急激に変化するときは、入力信号と出力信号の電圧差|V_out−V_in|が設定値V_Fを超えた時点で、定電流回路12においてスイッチ制御回路22がスイッチ20をオンにする。 - 特許庁
An optimum solution is found when initial values for the parameter are generated over multiple patterns by means of a random number generating mechanism, and on each of the initial values, automatic parameter extraction is carried out for selecting a combination of parameters giving a minimum difference between a final calculated value and an actual measurement value.例文帳に追加
乱数発生機構によってパラメータの初期値を多数のパターンにわたって生成し、それぞれの初期値に対して自動パラメータ抽出を実行し、最終的な計算値と実測値の差が最も小さくなるようなパラメータの組み合わせを選ぶことで、最適解を求める構成とした。 - 特許庁
Further, the halogenic addition quantity is detected excessive when a measured value is less than a low level threshold value 104 in which a disinfectant consumption quantity, which is a concentration difference (43-13) between both residual concentrations 43, 13, is set in advance.例文帳に追加
また両残留ハロゲン濃度43,13の濃度差(43−13)を消毒剤消費量としてこの消毒剤消費量を予め設定しておいた消毒剤消費量低レベルしきい値104と比較して低レベルしきい値104未満の場合はハロゲン系薬剤添加量の過剰として検知する。 - 特許庁
Namely, when a difference between pressure in the bag 11 and pressure in a gas supply chamber 16 exceeds a preset value, the differential pressure valve 31 carries gas from the bag part 11 to the outside to restrict the pressure increase amount to be the predetermined value or smaller after it is subjected to the thrust.例文帳に追加
すなわち、バッグ部11内と気体供給室16内との差圧が、予め設定した設定値を超えたときに、差圧バルブ31によって、バッグ部11内の気体を外部へ流出させることで、上記押圧力を受けたときからの圧力増大量を所定値以下に規制する。 - 特許庁
To provide a tracking servo device of an optical information recording/reproducing device capable of adjusting the maximum value of the amplitude of a tracking error signal while preventing the decrease of the level of the maximum amplitude value of an RF signal even though the spherical aberration is generated by the thickness difference of a transparent plate of an optical disk.例文帳に追加
光ディスクの透明板の厚さ誤差によって球面収差が生じてもRF信号の振幅最大値レベルの低下を防止しつつトラッキングエラー信号の振幅最大値調整を可能にした光学式情報記録再生装置のトラッキングサーボ装置を提供する。 - 特許庁
To provide a rolling bearing and a spindle device to suppress a non-rotary synchronous component to a further lower value by limiting the number of rolling elements and a lubricant amount apart from suppression of the configurational error of an orbital plane and the rolling element and the mutual difference in size of the rolling element to a lower value.例文帳に追加
軌道面や転動体の形状誤差、転動体の寸法相互差を小さく抑えることとは別に、転動体の個数や潤滑剤量を限定することで非回転同期成分をより小さく抑えた転がり軸受及びスピンドル装置を提供することを課題とする。 - 特許庁
An arithmetic unit 130 computes adaptive devices using the difference of an image distortion between the original process and the current process as an allowable value and the image-distortion correction value in response to an inquiry from the host containing at least a part of the original-process information, and answers the information of the result of the computation to the host.例文帳に追加
そして、その元工程情報の少なくとも一部を含むホストからの問い合わせに応じ、演算装置130が、元工程と現工程との像歪みの差が許容値となる適合装置及びその像歪み補正値を算出し、その算出結果の情報をホストに回答する。 - 特許庁
The current-detecting means monitors the electric power source current, and the current control means generates a control signal for the variable load means, using as an error signal, the difference between a reference current value in response to an operation mode and the detected current value, based on the signal from the memory control means.例文帳に追加
電流検出手段で電源電流をモニタし、電流制御手段ではメモリ制御手段からの信号に基づき動作モードに応じたリファレンス電流値と検出した電流値との差分を誤差信号として可変負荷手段に対する制御信号を生成する。 - 特許庁
CAZAC sequences that satisfy the condition that the absolute value |N-L| of a difference between a sub-carrier number N in a resource block and a CAZAC sequence length L is not larger than a threshold value K are selected, and a CAZAC sequence having the greatest prime factor constituting a sequence length is selected from the selected CAZAC sequences.例文帳に追加
リソースブロックのサブキャリア数NとCAZAC系列の系列長Lとの差の絶対値|N−L|が閾値K以下となるCAZAC系列を選択し、その中から系列長を構成する最大素因子が最も大きいCAZAC系列を選択する。 - 特許庁
The part 24b uses image pickup image data itself and image data red from either a frame memory 24a or 24b, calculates the shifting of one image data with which the difference between the value of a shifted pixel of one image data and the value of a pixel of the other image data is minimized, and defines it as hand shake correction quantity.例文帳に追加
相関演算部24b では撮像画像データそのものとフレームメモリ24a または24e のいずれかから読み出した画像データとを用い、一方の画像データのずらした画素と他方の画像データの画素の値の差を最小にする一方の画像データのずらしを求め、手振れ補正量とする。 - 特許庁
A designated section of brain waves (ECS) is divided into fine section units, a P-P amplitude value of the minimum amplitude difference to the maximum amplitude by each divided section unit is obtained, and the frequency of the same value as the P-P amplitude in a designated divided section unit is obtained to display a histogram.例文帳に追加
脳波(ECS)の所定区間を細かい区間単位に分割して、分割区間単位毎の最大値振幅に対する最小値振幅差のP−P振幅値を求め、所定の分割区間単位中のP−P振幅値と同一値となる度数を求めてヒストグラム表示させる。 - 特許庁
To the contrary, the identical color whose lightness is five or below in Munsell value is applied to the right opening/closing door 13, left opening/closing door 14 and rear opening/closing door 15 such that a difference in lightness in Munsell value between these doors and the main body of the external member 10 is three or greater as compared with the main body of the external member 10.例文帳に追加
これに対し、右開閉扉13、左開閉扉14及び後開閉扉15は、外装部材10の本体部に比較して、マンセル値における明度差が3以上となるように、マンセル値における明度5以下の色で、同色に着色されている。 - 特許庁
A surrounding monitoring device for a vehicle generates a first gray-scale image having a luminance value corresponding to the temperature of the object and a second gray-scale image having a luminance value corresponding to the temperature difference of the object with respect to a background on the basis of the first gray-scale image through imaging by an infrared camera mounted on the vehicle.例文帳に追加
車両に搭載された赤外線カメラによる撮像を介して、対象物の温度に応じた輝度値を有する第1のグレースケール画像と、第1のグレースケール画像に基づいて、背景に対する対象物の温度差に応じた輝度値を有する第2のグレースケール画像を生成する。 - 特許庁
Based on a difference between the minimum value and average value of the values of currents flowing in an electrostatic latent image, it is determined whether to perform a level alteration checking operation for the inter-peak voltage of the AC voltage applied to the charging means during an image forming operation.例文帳に追加
潜像担持体に流れる電流値の最小値と平均値の差分に基づいて、画像形成工程において帯電手段に印加される交流電圧のピーク間電圧の段階変更確認動作を行うか否かを判断する制御を行うことを特徴とする。 - 特許庁
A control means is provided which starts regenerative control for recollecting electric energy into a battery while braking a vehicle if a speed difference between a detected vehicle speed and a speed command is a predetermined value or larger and the vehicle speed is a predetermined value or higher when the accelerator pedal 10 is returned.例文帳に追加
アクセルペダル10の戻し時に、検出された車両速度と速度指令との速度差が所定の値以上であり、車両速度が所定の値以上であるときに、車両の制動と共にバッテリーに電気エネルギーを回収する回生制御を開始する制御手段を備えた。 - 特許庁
An absolute value 354 of the difference between both of the distance information is determined in each frequency, and a band 358 whose absolute value exceeds a prescribed threshold D_Err is treated as one including a noise signal and removed, to thereby acquire an effective frequency band including the Doppler signal based on the reflected wave from an object.例文帳に追加
周波数毎に両距離情報の差の絶対値354を求め、その絶対値が所定の閾値D_Errを越える帯域358はノイズ信号を含むものとして除去し、物体からの反射波に基づくドップラ信号を含む有効周波数帯域を取得する。 - 特許庁
Voltage on a memory cell is pumped (up or down), thereby, voltage stored in a memory cell is increased (upper than a voltage value of logic 1) or decreased (lower than a voltage value of logic 0), also, voltage difference increased on a bit line is given during a read-out operation period after that of the memory cell.例文帳に追加
本発明は、メモリセル上の電圧をポンピング (アップ又はダウン)し、それによりメモリセル内に格納されている電圧を増加 (論理1電圧値より上)又は減少 (論理0電圧値より下)させ、且つメモリセルのその後の読取動作期間中にビット線上に増加された電圧差を与える。 - 特許庁
A control means of an image forming device controls a difference between the surface speed of the intermediate transfer belt and the peripheral speed of the secondary transfer roller to fall within a predetermined range by detecting a torque command value for an intermediate transfer drive motor 200 and controlling the peripheral speed of the secondary transfer roller based on the detected result of the torque command value.例文帳に追加
中転駆動モータ200に対するトルク指令値を検出し、トルク指令値の検出結果に基づき二次転写ローラの周速度を制御することにより、二次転写ローラの周速度と中間転写ベルトの表面速度との速度差が所定範囲内となるように制御する。 - 特許庁
In the case that the difference of offset adjusting values of this time and the preceding time is in an allowble range, a seat is judged to be in a vacant state wherein nothing exists on the seat, a weight value of this time is stored in data stored in an EEPROM 59, and an offset adjusting value is updated.例文帳に追加
そして、ステップS140では、今回値と前回のオフセット調整値の差が許容範囲α内にある場合には、シート上に何もない空席状態と判断し、EEPROM59に記憶しているデータWoに今回の重量値Wを記憶し、オフセット調整値の更新を行う。 - 特許庁
During the fuel injection amount change, a target opening θt is calculated, on the basis of a correction amount Δθ based on a difference between the actual rotation speed and the target idle rotation speed, a learning value θg in accordance with the correction amount, and a correction value θa for correcting at least one of them.例文帳に追加
燃料噴射量変更時には、実際の回転数と目標アイドル回転数との差分に基づく補正量Δθ、補正量に応じた学習値θg、およびこれらのうちの少なくとも一方を補正する補正値θaに基づき、目標開度θtを算出する。 - 特許庁
In the paper feeding operation, the loading tray 11 is lifted up to the reference position when a value of a difference between the vertical directional position of the other end part of the uppermost surface sheet 2A on the loading tray 11 detected by the position detecting analog sensor 16 and the reference position data is a predetermined value or more.例文帳に追加
給紙動作中には、位置検出アナログセンサ16が検出している積載トレイ11上の最上面シート2Aの他端の部分の鉛直方向位置と、基準位置データとの差の値が所定の値以上であるときに積載トレイ11を基準位置まで上昇させる。 - 特許庁
The control device 30 determines that at least either of the voltage sensors 10 and 13 fails when the voltage difference between the voltage Vm from the voltage sensor 13, and the D.C. voltage Vb from the voltage sensor 10 is below the reference value, and when the direct current Ib is below the threshold value.例文帳に追加
また、制御装置30は、電圧センサ13からの電圧Vmと電圧センサ10からの直流電圧Vbとの電圧差が基準値を下回るときであって、かつ、直流電流Ibが閾値を下回るとき、電圧センサ10,13の少なくとも一方が故障していると判定する。 - 特許庁
A temperature rise value of a main spindle is calculated when setting rotation starting time as the origin in a state of sufficiently cooling the main spindle, and a difference from the reference temperature is calculated as the temperature rise value when a temperature is saturated in a temperature rise from the reference temperature (S-11).例文帳に追加
そして、主軸の温度上昇値を回転の開始時を基点とする場合には、主軸が十分冷えた状態で、基準温度からの温度上昇とする場合には、温度が飽和したときの基準温度との差を温度上昇値として算出する(S−11)。 - 特許庁
An imaging apparatus 1 has a peripheral light quantity correction circuit 6 for performing luminance correction of a picked up image with a luminance value in one of two areas as a target luminance value so as to cancel a difference in luminance between a central area and a peripheral edge area in the picked up image by a solid-state imaging sensor 3.例文帳に追加
撮像装置1は、固体撮像素子3による撮像画像における中心領域と周辺領域との輝度差を解消するために、一方の領域の輝度値を目標輝度値として撮像画像の輝度補正を行う周辺光量補正回路6を有する。 - 特許庁
When the density of the patch image detected by the density sensor 224 is thinner than target toner density stored in a target toner density memory 122, and a value of difference between them is equal to or above a predetermined value V1, a toner supply stop flag stored in a toner supply stop flag memory 124 is updated.例文帳に追加
濃度センサ224で検出されたパッチ画像の濃度が、目標トナー濃度メモリ122に記憶された目標トナー濃度よりも薄く、その差分値が所定値V1以上の場合に、トナー供給停止フラグメモリ124に記憶されたトナー供給停止フラグを更新する。 - 特許庁
To make the control of current conduction to a heating resistor performable with a high precision by compensating the difference between fed voltage to the heating resistor which is the reference for control and/or the resistance value of the heating resistor and the actually fed voltage to the heating resistor and/or the resistance value of the heating resistor.例文帳に追加
制御基準となる発熱抵抗体への給電電圧又は/及び発熱抵抗体の抵抗値と、実際の発熱抵抗体への給電電圧又は/及び発熱抵抗体の抵抗値との差を補正して、発熱抵抗体への通電制御を高精度に行えるようにする。 - 特許庁
A control section 69 grasps a time point from a time register 65 when an amount of waste ink possibly existing in an ink absorption body 8 at the present, i.e., a counter value (a protection counter value) of a waste ink amount protection counter 63 is updated, and then calculates an evaporation time period based on a difference between the time point and the present time.例文帳に追加
制御部69は、現在インク吸収体8に存在し得る廃インク量、つまり、廃インク量保護カウンタ63のカウンタ値(保護カウンタ値)が更新されたときの時刻を時刻レジスタ65から把握し、その時刻と現在時刻との差分から蒸発時間長を求める。 - 特許庁
The printing device driving timing triggered by each rotary encoder signal is corrected using the difference of the theoretical value of each rotary encoder signal output time and the average value of the actual rotary encoder signal output time to eliminate the deviation of the printing points between the apparatuses to stabilize the printing quality.例文帳に追加
各ロータリーエンコーダー信号をトリガとする印字素子駆動タイミングを、各ロータリーエンコーダー信号出力時間の理論値と実際のロータリーエンコーダー信号出力時間の平均値との差を用いて補正することで印刷位置の機差を無くし、印刷品質を安定させる。 - 特許庁
An update determination part 20 evaluates the difference between the local pixel value variance and the local noise variance for each pixel of the image being restored to determine whether or not to update each pixel value by iterative calculations, and notifies the iterative restoration part 14 of pixels to be excluded from iterative calculations.例文帳に追加
更新判定部20は、復元過程の画像の各画素について画素値の局所的な分散とノイズの局所的な分散の差分を評価し、反復計算により各画素値を更新するか否かを判定し、反復計算を打ち切る画素を反復復元部14に通知する。 - 特許庁
After stopping the engine 1, the temperature TSR of the oxygen concentration sensor 21 is controlled to be a second temperature TSR2 higher than the first temperature TSR1 and a difference between a maximum value VMAX for the sensor output VO2 at this time and the storage value VO2M is set to be a change amount DVO2 (S19, S20).例文帳に追加
エンジン1の停止後、酸素濃度センサ21の温度TSRを第1の温度TSR1より高い第2の温度TSR2に制御し、そのときのセンサ出力VO2の最大値VMAXと、記憶値VO2Mの差を変化量DVO2とする(S19,S22)。 - 特許庁
The wall thickness of each of multiple inspection parts 12a-12c set to a trunk portion 12 of a preform 1 is measured, and each of the measured wall thicknesses is compared with a preset set value, whereby the difference between the measured wall thickness and the set value is inspected for each inspection part.例文帳に追加
プリフォーム1の胴部12に設定された複数の検査部位12a〜12cのそれぞれの肉厚を計測し、計測された肉厚のそれぞれを予め設定された設定値と比較することによって、計測された肉厚と、設定値との差異を検査部位毎に検査する。 - 特許庁
Next, a control circuit 4 compares the average power value S5 with a reference voltage value Vref via an error amplifier U2, and controls the drive circuit U3 of an inverter circuit 3 via a voltage controlled oscillator U1 so that the difference therebetween becomes zero, thereby varying the switching frequencies of switching elements T1, T2.例文帳に追加
次に制御回路4にて、誤差アンプU2を介し、平均電力値S5と基準電圧Vrefを比較し、この差を0とするように電圧制御発振器U1を介し、インバータ回路3の駆動回路U3を制御し、スイッチング素子T1,T2のスイッチング周波数を可変する。 - 特許庁
An error output obtained by the comparison of the output of the amplitude difference with a set value SP by means of an adder 114 is added to the oscillation signal with the adder from a feedback amplifier 115 and fed back to an electrode for z displacement of the piezoelectric tube to control the average distance between the tip part and the sample to a set value.例文帳に追加
加算器114で振幅差出力と設定値SPとを比較して得られる誤差出力は帰還増幅器115から加算器で発振信号と加算され、ピエゾチューブのz変位用電極に帰還されて先端部と試料との平均距離を設定値に制御する。 - 特許庁
A first blood vessel diameter measurement value D1 is obtained by a first blood vessel diameter measuring part 4, and a second blood vessel diameter measurement value D2 is simultaneously obtained by a second blood vessel diameter measuring part 6 so that there is a height difference between the first blood vessel diameter measuring part 4 and the second blood vessel diameter measuring part 6.例文帳に追加
第1血管径測定部4と、第2血管径測定部6とに高低差を設けた状態で、第1血管径測定部4による第1血管径測定値D1を取得し、同時に第2血管径測定部6による第2血管径測定値D2を取得する。 - 特許庁
When a detected value with the downstream pressure sensor 29 of the hydrogen pressure control valve is abnormal or the difference between detected values of the downstream pressure sensor of a doubled hydrogen pressure control valve reaches a prescribed value or higher, a hydrogen pressure control part 35 determines that the downstream pressure sensor 29 of the hydrogen pressure control valve is abnormal.例文帳に追加
水素圧力制御部35は、水素調圧弁下流圧力センサ29の検出値が異常であるか、2重化した水素調圧弁下流圧力センサ29の検出値の差が所定値以上の時に、水素調圧弁下流圧力センサ29が異常と判定する。 - 特許庁
The inkjet ink contains an organic pigment, a water-soluble organic solvent, water, and a polymeric dispersant, wherein the polymeric dispersant is a block copolymer having difference between an amine value and an acid value of more than 0, and the organic pigment is a compound (A), a tautomeric structure thereof, or a hydrate thereof.例文帳に追加
有機顔料、水溶性有機溶媒、水及び高分子分散剤を含有し、該高分子分散剤はアミン価と酸価の差が0より大きいブロック共重合体であり、かつ該有機顔料が下記化合物(A)、その互変異性構造体またはその水和物であるインクジェットインク。 - 特許庁
A printer sequentially switches a parameter (gain value) to a plurality of predetermined values at a certain interval since conveyed paper reaches a conveyance roller, and calculates, as rotation irregularity, the highest value of the rotation speed difference of a conveyance motor for driving the conveyance roller in each of periods I, II, III, IV.例文帳に追加
プリンタでは、搬送されてきた用紙が搬送ローラに到達した後から一定の時間間隔で、パラメータ(ゲイン値)を複数の所定値に順次切替え、各期間I,II,III,IV,Vにおいて、搬送ローラを駆動する搬送モータの回転速度差の最大値を、回転ムラとして算出する。 - 特許庁
When a variation value per time (dP/dt) of the difference between the first supply pressure P1 and the second supply pressure P2 is larger than a prescribed value in the steady power generation of the fuel cell 1, the control devices S101-S123 determine that the supply valve 63 is closed, and sound an alarm.例文帳に追加
制御装置S101〜S123は、燃料電池1の定常発電時に、第1供給圧P1と第2供給圧P2との差の単位時間当たりの変化値(dP/dt)が所定値よりも大きい場合、供給弁63が閉じたと判定し、警報を発する。 - 特許庁
A substantial error indicated by a difference ΔT occurs between an integrated value Σ(Rx(i+1)-Rx(i)) of Rx intervals of the receiving time Rx of TS packets in the upper stage of the figure and an integrated value Σ(Tx(i+1)-Tx(i)) (=t) of time stamps Tx of the TS packets.例文帳に追加
図3の上段の各TSパケットの受信時刻RxのRxインターバルの積算値Σ(Rx(i+1)−Rx(i))と、各TSパケットのタイムスタンプTxの積算値Σ(Tx(i+1)−Tx(i))(=t)との間には、差分ΔTで示す実質的な誤差が生じる。 - 特許庁
To provide an inexpensively composed optical fiber connecting structure and a connecting member which are capable of suppressing connection loss within a prescribed range with a single intermediate optical fiber, in the case where a difference above a prescribed value exists in the MFD (mode field diameter) value of optical fibers to be connected to each other.例文帳に追加
互いに接続しようとする光ファイバのMFD値に、所定値以上の差がある場合に、単一の中間光ファイバを用いて所定範囲内の接続損失に抑えることができ、安価な構成の光ファイバの接続構造と光接続部材を提供する。 - 特許庁
In other words, the intermediate layer 20 is formed so that its thickness is set larger than an average pore size of the anode-side electrode 12, and at the same time, a difference of a value of the average pore size of the anode-side electrode 12 deducted from a value of the thickness of the layer 20 is to be within 0 to 17 μm.例文帳に追加
すなわち、中間層20の厚みをアノード側電極12の平均気孔径以上に設定するとともに、中間層20の厚みの値からアノード側電極12の平均気孔径の値を差し引いた差が0〜17μmの範囲内となるように、中間層20を形成する。 - 特許庁
The double-faced laminated metal plate is prevented from undergoing whitening due to working by setting the difference ΔHz between a haze value Hz2 of the lower melting temperature film 3 after bending by 180° outside with sandwiching a plate 4 having a thickness of 1 mm and a haze value Hz1 of the lower melting temperature film 3 before the bending to ≤20%.例文帳に追加
この両面ラミネート金属板を、厚さ1mmの板4を挟んで外側に180°曲げ加工を加えた後の低融点フィルム3のヘーズ値Hz2と、曲げ加工前の低融点フィルム3のヘーズ値Hz1との△Hzを、20%以下とすることにより、加工による白化をなくした。 - 特許庁
Thus, it is possible to decrease a difference between a time required for the input signal A exceeding a threshold value of the inverter circuit 21 at the change in the input signal A from the low level to the high level and a time required for the input signal A exceeding the threshold value of the inverter circuit 21 at the change in the input signal A from the high level to the low level.例文帳に追加
これにより、入力信号Aがローレベルからハイレベルに変化する際にインバータ回路21のしきい値を超えるのに必要な時間と、ハイレベルからローレベルに変化する際にインバータ回路21のしきい値を超えるのに必要な時間との差を小さくすることができる。 - 特許庁
(ii) In the case of (i) above, when the total amount of payments from the clients is less than the purchase value of the government bonds, the Financial Instruments Business Operator shall jointly buy the bonds by paying the difference between the purchase value of the minimum unit and the said amount. 例文帳に追加
② 上記①の場合、顧客からの払込金等の合算額について国債の買付価額に満たない金額が生ずるときは、金融商品取引業者は、最小単位の買付価額と当該金額との差額を払い込むことにより、顧客と共同して買い付けること。 - 金融庁
From a difference between a measured value of the distance between the first gate electrode 310 and the first contact 320, and a design value of the distance, a superimposing error between exposure processing for forming the first gate electrode 310 and exposure processing for forming the first contact 320 can be measured.例文帳に追加
そして、第1ゲート電極310と第1コンタクト320の距離の測定値と、この距離の設計値との差から、第1ゲート電極310を形成するための露光処理と、第1コンタクト320を形成するための露光処理と、の間の重ねあわせ誤差を測定することができる。 - 特許庁
This data processing method extracts similar input data whose value is close to input data of interest from among input data, that is, e.g. the absolute value of finite difference from the input data of interest which is equal to or less than prescribed threshold th and finds a straight line approximating the similar input data.例文帳に追加
入力データから、注目している注目入力データと値の近い類似入力データ、即ち、例えば、注目入力データとの差分の絶対値が、所定の閾値th以下のものが抽出され、その類似入力データを近似する直線が求められる。 - 特許庁
A sensor output processing circuit of a combustion pressure sensor 24 is provided with a bottom value holding circuit 50 having a capacitor 52 for holding a bottom value of an output of the sensor 24, and a differential amplifier 62 for obtaining difference between an output of the sensor 24 and an output of the holding circuit 50.例文帳に追加
燃焼圧センサ24のセンサ出力処理回路は、燃焼圧センサ24の出力のボトム値ホールド用のコンデンサ52を有するボトム値ホールド回路50と、燃焼圧センサ24の出力とボトム値ホールド回路50の出力の差をとる差動増幅器62を備えている。 - 特許庁
Deceleration is controlled based on an output value Iout(0) of an integral element of a difference Δα between a deceleration αv of a vehicle and a reference deceleration αref at a normal time, and at an anti-skid control, the above deceleration control is stopped and the output value Iout(0) is initialized by '0'.例文帳に追加
通常時は車両の減速度αvと規範減速度αrefとの差Δαの積分要素の出力値Iout(0)に基づいて減速度制御を行い、アンチスキッド制御が行われているときは、前記減速度制御を中断し且つ前記出力値Iout(0)を“0”で初期化するようにした。 - 特許庁
| 例文 |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|