| 例文 |
driving commandの部分一致の例文一覧と使い方
該当件数 : 807件
When a command for driving a seat belt retractor with the motor 5 is given to a motor control circuit 6, the motor control circuit 6 starts power supply to the motor 5 and puts a clutch 3 into a state of connecting the seat belt retractor 1 and a reduction gear 4.例文帳に追加
モータ制御回路6に、モータ5によるシートベルトリトラクタの駆動指令が出させると、モータ制御回路6は、モータ5への給電を開始すると共に、クラッチ3を、シートベルトリトラクタ1と減速機4を結合する状態とする。 - 特許庁
The vehicle control device comprises an estimation part that estimates suppliable drive power that can be supplied for driving the vehicle, and a drive request power command part in accordance with an acceleration opening and the estimated suppliable drive power.例文帳に追加
この車両制御装置は、車両の駆動のために供給可能な供給可能駆動電力を推定する推定部と、アクセル開度と推定供給可能駆動電力とに応じて駆動要求電力司令部とを備える。 - 特許庁
In case of determining that the sliding roof is not totally closed, the control part 11 sends a total closure command of the sliding roof 4 to a sliding roof motor driving circuit 22.例文帳に追加
そして、スライドルーフ4が全閉であるかをスライドルーフ全閉検出センサ12よりの検出信号により判断し、スライドルーフ4が全閉でないと判断すれば、制御部11はスライドルーフモータ駆動回路22にスライドルーフ4の全閉指令を発信する。 - 特許庁
The driving portion, which supplies output from a rectification means to the motor, comprises an optical coupling means 92 for transmitting the command signal via an optical signal, and the rectifier means 93 for rectifying the output of the optical coupling means.例文帳に追加
駆動部は、指令信号を光信号を介して伝達する光結合手段92と、該光結合手段の出力を整流する整流手段93とを有し、該整流手段からの出力をモータに供給する。 - 特許庁
An adjusting command value of torque correspondence fastening force is adjusted by multiplying the driving torque by the correction coefficient, thereby solving a problem such as heat generation of the clutch or a gear or degradation of fuel consumption by the mounting of the tires having different diameter.例文帳に追加
そして、この補正係数を駆動トルクに乗じてトルク対応締結力調整指令値を調整することにより、異径タイヤの装着によるクラッチおよび歯車の発熱や燃費の悪化といった問題を解消する。 - 特許庁
In the speed control method for the rolling main motor 1 for driving a stand of the tandem mill, an ideal response correction circuit 5 is provided in the output stage of a motor speed command of an MRH circuit which is the speed reference of the whole line.例文帳に追加
タンデム圧延機のスタンドを駆動する圧延主機モータ1の速度制御方法であって、ライン全体の速度基準となるMRH回路4のモータ速度指令の出力段に、理想応答補正回路5を設ける。 - 特許庁
This apparatus is provided with an induced voltage detecting means 6 for detecting the induced voltages of a plurality of synchronous motors 31 to 3n, amplifiers 21 to 2n for amplifying power based on a command and driving a plurality of synchronous motors, and a host controller 1.例文帳に追加
複数の同期電動機31〜3nの誘起電圧を検出する誘起電圧検出手段6と、指令に基づいて電力を増幅し、複数の同期電動機を駆動するアンプ21〜2nと、上位コントローラ1を備える。 - 特許庁
Receiving the artificial signal, the automatic light controller 24 automatically turns off light and the lock release controller 25 outputs a lock release command signal to a door lock driving unit 26 to automatically unlock the door.例文帳に追加
この擬似信号の入力により、オートライト制御部24は点灯しているライトを自動的に消灯させ、解錠制御部25はドアロック駆動装置26に対して解錠指令信号を出力してドア錠を自動的に解錠させる。 - 特許庁
The control system gives a command to a display arm driving system so as to make a display arm 5 retreat, until output from a retreat limit position sensor is turned on, that is, to a retreat limit being a 2nd position, where the arm 5 is housed in a housing part 4.例文帳に追加
すると制御系は、ディスプレイアーム駆動系に指令を出し、ディスプレイアーム5を後退限位置センサの出力がオンとなるまで、すなわち、第2の位置である後退限まで後退させ、ディスプレイアーム5を収納部4内に収納する。 - 特許庁
The presentation command is input of the presentation button operation, for example, and the prerequisite conditions for driving the shooting device is that a signal is input from a touch sensor for detecting that the game player grips a shooting handle.例文帳に追加
演出指令は、例えば、演出ボタン操作による入力であり、発射装置を駆動するための前提条件は、例えば、遊技者が発射ハンドルを握っていることを検知するタッチセンサからの信号が入力されることである。 - 特許庁
In the compressor driving method with a synchronous motor 7 controlled by an inverter 6 and with a compressor 8 driven by the synchronous motor 7, a current limiter 3 for limiting a current command in a manner as not exceeding a current upper limit value is provided.例文帳に追加
インバータ6によって同期モータ7を制御し、同期モータ7によって圧縮機8を駆動する圧縮機駆動方法において、電流指令が電流上限値を越えないように制限する電流リミッタ3を設けた。 - 特許庁
Error estimation means 115-117 estimate positioning errors to a position command target value on the basis of the position posture target value 114 of the tip or preset point of the treatment table corresponding to each of the plurality of driving mechanism systems.例文帳に追加
複数の駆動機構系の各々に対応し、治療台の先端あるいは予め設定した点の位置姿勢目標値114に基づき位置指令目標値に対する位置決め誤差を誤差推定手段115〜117が推定する。 - 特許庁
When detecting a motor current of the induction motor 7 in the state where a driving command outputted by a driving target position determination device 22 based on the difference between a control rod target position and a measured control rod actual position does not exist, a power supply switch 33 for connecting the induction motor 7 to an alternating current source 37 is opened.例文帳に追加
本発明は、制御棒目標位置と測定された制御棒実測位置の差に基づいて駆動目標位置判定装置22が出力する駆動指令が無い状態で誘導電動機7の電動機電流が検出されると誘導電動機7を交流電源37に接続する電源開閉器33を開操作する。 - 特許庁
A phase processing circuit 35 constituting the inductive load driving device outputs two PWM signals that are respectively outputted to two FETs 23A and 23B in accordance with an input of a driving command signal from an engine ECU 32 in a state where the start timing of the fall of one signal is made to coincide with the end timing of the rise of the other signal.例文帳に追加
誘導性負荷駆動装置を構成する位相処理回路35は、エンジンECU32からの駆動指令信号の入力に応じて2つのFET23A,23Bに夫々出力する2つのPWM信号について、一方の信号の立下り開始タイミングと、他方の信号の立上がり終了タイミングとを一致させた状態で出力する。 - 特許庁
When a paper P is fed, commanded predetermined amount of paper sheets is fed, and it is determined that a rear end of the paper P is positioned in a BS driving region (low speed region) ABS, amount of paper feeding of a paper feeding command is divided so that paper feeding ends at an inlet Pb of the BS driving region ABS once and then remaining paper sheets are fed.例文帳に追加
用紙Pを紙送りする際、指令された所定量の紙送りをした場合、用紙Pの後端がBS駆動領域(低速領域)ABS内に位置することになると判断されると、BS駆動領域ABSの入口Pbで一旦紙送りが終わり、その後、残りの紙送りがなされるように紙送り指令の紙送り量を分割する。 - 特許庁
An inverter 6 driving an electric motor 4 of the electric compressor 3 performs self-cooling for the inverter by operating in the overheat protection mode driving the electric motor at the rotational speed for thermal protection different from the rotational command value from an air conditioning control device 20 and securing flow rate of the refrigerant when the detection temperature of an inverter temperature sensor 22g exceeds a predetermined value.例文帳に追加
電動圧縮機3の電動モータ4を駆動するインバータ6は、インバータ温度センサ22gの検出温度が所定値を超えると、空調制御装置20からの回転指令値とは異なる熱保護用回転数で電動モータを駆動する過熱保護モードで作動し、冷媒流量を確保してインバータの自己冷却を行う。 - 特許庁
In this electric power steering device, when output abnormalities of a torque sensor 3 are detected, a motor driving signal is produced on the basis of the last current command value sampled in a sampling circuit 7b before the output abnormalities of the torque sensor 3 are detected, and a motor 4 is operated on the basis of the motor driving signal for the specified time.例文帳に追加
本発明の電動パワーステアリング装置は、トルクセンサ3の出力異常が検出された時に、そのトルクセンサ3の出力異常が検出される前にサンプリング回路7bにサンプリングされている前回の電流指令値に基づいてモータ駆動信号を生成し、そのモータ駆動信号によって所定時間モータ4を駆動する。 - 特許庁
With the apparatus and the method for controlling a motor, a command to start duty control is issued wherein a waiting time is set for each driving operation as required from a point in time when the difference between the upper limit value of motor temperature at which the motor normally runs and a motor temperature is estimated to have fallen below a specified value after start of a series of driving operations.例文帳に追加
本発明に係るモータ制御装置及び制御方法は、一連の駆動動作開始後、モータが正常に動作するモータ温度の上限値とモータ温度との差が所定値未満になったと推測される時点から、一回の駆動動作ごとに必要に応じて待ち時間を設定するデューティ制御開始を指令するものである。 - 特許庁
In this electric power steering device which gives a steering assisting force to a steering mechanism through a motor driving circuit with a steering assisting command value based on a steering torque and a current control value calculated with a motor current value detected by a motor current detecting means, the switching device is provided between the motor driving circuit and the motor current detecting means.例文帳に追加
操舵トルクに基づく操舵補助指令値と、モータ電流検出手段で検出されたモータ電流値とで演算した電流制御値でモータ駆動回路を介してステアリング機構に操舵補助力を与える電動パワーステアリング装置において、前記モータ駆動回路と前記モータ電流検出手段との間に開閉装置を設ける。 - 特許庁
A motor driving device includes a DC power supply section which varies electrically output voltages; a voltage regulator which varies output voltages of DC power supply section to apply them to a motor driving section, wherein the DC power supply section adopts a switching type, makes a feedforward control according to a rotation command, and the voltage regulator controls applied voltages to the motor through feedback control.例文帳に追加
電気的に出力電圧を可変できる直流電源部と、直流電源部の出力電圧を可変してモータ駆動部に印加する電圧調節器を設け、直流電源部はスイッチング方式として回転指令によってフィードフォワード制御し、電圧調節器はフィードバック制御によってモータへの印加電圧を制御する。 - 特許庁
This device gathers a plurality of times of an absolute value of a speed deviation between a speed command to a driving means for opening and closing the elevator door with respective story floors and an actual speed of the driving means; and determines a speed deviation value with respective story floors by comparing these deviation values with a value of doubling a predetermined speed deviation value by a constant.例文帳に追加
各階床毎にエレベータドアの開閉を行う駆動手段に対する速度指令と前記駆動手段の実際速度との速度偏差の絶対値を複数回採取し、これらの偏差値を予め決められた所定の速度偏差値を定数倍した値と比較して各階床毎の速度偏差値を求めることを特徴とする。 - 特許庁
Polarity inversion of a driving voltage is started by setting the final on time of a first control signal so that a current flowing through a coil L1 has a desired current value I1 regardless of the reception timing of a polarity inversion command signal.例文帳に追加
極性反転指令信号の受信タイミングに関わらず、コイルL1に流れる電流を所望の電流値I1になるように最終の前記第1の制御信号のオン時間を設定して駆動電圧の極性反転を開始する。 - 特許庁
A piston which is an operation member of a hydraulic servo valve for driving a variable turbocharger is operated, and the electric command for preventing silting of a size not changing the flow velocity of exhaust gas adjusted by the variable turbocharger is imparted to an EPC valve.例文帳に追加
可変ターボチャージャを駆動するための油圧サーボ弁の作動部材であるピストンを作動させ、かつ可変ターボチャージャで調整される排気ガスの流速が変化しないような大きさのシルティング防止用の電気指令をEPC弁に与える。 - 特許庁
On the other hand, in a mileage-priority mode in which the torque high response is not required, the voltage command of the converter is set so that the power loss in the entire motor driving system is minimized, based on the operating state of the AC motor (S150).例文帳に追加
一方、トルク高応答が必要な状態ではない燃費優先モードでは、交流電動機の運転状態に基づいて、電動機駆動システム全体での電力損失が最小となるように、コンバータの電圧指令値を設定する(S150)。 - 特許庁
A power loss of a driving system is estimated on the basis of load torque calculated from a relation between an accelerator opening degree 9d and a torque output of a motor and the motor is driven by a power loss compensation motor command value T0 compensating the loss.例文帳に追加
さらに、アクセル開度9dとモータのトルク出力との関係から算出される負荷トルクとに基づいて駆動系の動力損失を推定し、その損失を補償する動力損失補償モータ指令値T0でモータを駆動する。 - 特許庁
The mode transfer switch outputs a command signal having a redundancy degree as combination of output of plural switch elements in each of plural positions switched according to plural driving modes of high speed four wheel, high speed two wheel, and low speed four wheel.例文帳に追加
モード切換えスイッチは、高速四輪、高速二輪及び低速四輪のような複数の駆動モードに応じて切り換えられる複数のポジション毎に、複数のスイッチ素子の出力の組合せとして冗長度を持った指令信号を出力する。 - 特許庁
The control circuit 21 controls the drive circuit by reading out a driving parameter P corresponding to either a low frequency drive mode or a normal mode from the EEPROM 20 in accordance with a switching command signal Sw received externally.例文帳に追加
コントロール回路21は、装置外部から受け取った切替コマンド信号Swに応じて、EEPROM20から低周波数駆動モードまたは通常モードのいずれかに相当する駆動パラメータPを読み出すことにより駆動回路を制御する。 - 特許庁
In addition, a CPU 34 is configured to set an output value of the laser beam in accordance with an input from an input device 31 and to give the driving circuit 12 a command value corresponding to the output set value.例文帳に追加
また、入力装置31からの入力に応じてCPU34によりレーザ光の出力設定値を設定可能とされており、CPU34は、その出力設定値に応じた指令値を駆動回路12に与えるように構成されている。 - 特許庁
To provide a limiting circuit of output torque for securing safety by interrupting power in a driving part when the output torque at a distal end of a tool of an industrial robot determined by a calculation from a command torque signal exceeds an allowable value.例文帳に追加
指令トルク信号から演算により求めた産業用ロボットのツール先端での出力トルクが許容値を超えたときに駆動部の動力を遮断することで安全を確保する、出力トルクの制限回路を与えることを目的とする。 - 特許庁
A door is continually kept open when a cage 1 is in a position where a door 23 of the cage 1 is engageable with a door 9 of a gate 8, moreover, when the door 23 of the cage 1 is controlled to be openable and closable by a command of driving control panel 5 during the rescuing procedure.例文帳に追加
救出処理時、かご1のドア23と乗り場8のドア9が係合できる位置にかご1があった場合で、且つ、かご1のドア23が運転制御盤5の指令にて開閉可能であった場合には、ドア開状態を継続させる。 - 特許庁
A current source 102 is provided as a common power source for the semiconductor light sources 101-1 to 101-K to supply the driving currents of the semiconductor light sources 101-1 to 101-K according to the result of addition of the current command values N_1 to N_K.例文帳に追加
電流源102は、半導体光源101−1〜101−Kの共通電源として設けられ、半導体光源101−1〜101−Kの駆動電流を、電流指令値N_1〜N_Kの加算の結果に応じて供給する。 - 特許庁
A control means is configured to determine the type of the objective lens being the object to be switched, based on setting by an input means and a switching command from an operating means, and also, change the braking condition of a driving means in accordance with the determined type of the objective lens.例文帳に追加
制御手段は、入力手段による設定及び操作手段からの切換指令によって切換先の対物レンズの種別を判断すると共に、判別された対物レンズの種類に応じて駆動手段の制動条件を変更する。 - 特許庁
Then, the output voltage of the differential amplifier 53 is changed by the intensity of spots image-formed on the photodetectors 51a to 51c, and when the output voltage surpasses a threshold in a control circuit part 54, a command for stopping the driving of a movable mirror control circuit is transmitted.例文帳に追加
従って、受光素子51a〜51d上に結像したスポットの強度によって差動増幅器53の出力電圧が変化し、制御回路部54において閾値を越えていると可動ミラー制御回路の駆動を停止するための指令値を送る。 - 特許庁
In the ECU 10 (a control device of an electric power steering), the stable steering suppressing the influence of the difference in temperature and heat generation can be operated by correcting the temperature to the current command for driving an electric motor 23.例文帳に追加
本発明に係るECU10(電動式ステアリングの制御装置)によれば、電動モータ23を駆動するための電流指令値に温度補正を行うことで、寒暖の差や発熱の影響を抑えた安定したステアリング操作が可能となる。 - 特許庁
The dummy processing unit is set to standby by for an estimated processing time (estimated processing time of the substrate processing unit), included in simulation data; and thereafter the unit acquires the execution result data, and returns the data as a processing completion notification, to the sequence control part via the driving command activation part.例文帳に追加
擬似処理ユニットでは、シミュレーションデータに含まれる推定処理時間(基板処理ユニットの推定処理時間)待機した後、実行結果データを取得し、これらを、処理完了通知として、駆動コマンド起動部を介して、シーケンス制御部に返す。 - 特許庁
When a stop command is received from a remote controller, a first switch 21 and a second switch 22 are turned off by instruction by an outdoor microcomputer 43, so as to stop electric power supply from a commercial power source C.P to a compressor driving motor 27 and a fan motor 28.例文帳に追加
リモコンから停止命令を受けると、室外マイクロコンピュータ43の指令により第1スイッチ21及び第2スイッチ22はオフにされ、圧縮機駆動用モータ27、ファンモータ28への商用電源C.Pからの電力供給が停止される。 - 特許庁
When pushing down a stopping button 21C in a remote monitoring control device 20, a gate opening value and a stopping command are inputted to a gate driving device 10 after prescribed time (transmission delay time t3) passes via a telecommunication line 30.例文帳に追加
遠隔監視制御装置20において停止釦21Cが押下された場合には、ゲート開度値及び停止指令が、通信回線30を介して所定の時間(伝送遅れ時間t3)を経過した後、ゲート駆動装置10に入力される。 - 特許庁
When a tilting level 6 is operated and either of a detection switch 9 or 10 is turned on, a CPU 51 selects the map diagram corresponding to the lifting level detected by the lifting level sensor 5 and outputs a command signal corresponding to the map diagram to a cargo handling motor driving circuit 57.例文帳に追加
ティルトレバー6が操作され、各検知スイッチ9,10のいずれかがオンすると、CPU51は、揚高センサ5の検出揚高に応じたマップ線を選択し、そのマップ線に応じた指令信号を荷役モータ駆動回路57に出力する。 - 特許庁
After a new storage tape C is connected to an old storage tape C, a CPU 110 sends a feed command to a component supply unit 6 to drive a servo motor 28 and a driving motor 42 of the supply unit 6, thereby performing component feed operation.例文帳に追加
古い収納テープCに新しい収納テープCを連結した後、部品供給ユニット6にCPU110は送り指令を送り、当該供給ユニット6のサーボモータ28及び駆動モータ42を駆動させて、部品送り動作等を行わせる。 - 特許庁
The motor driving device includes a sensor (43) for detecting the rotating state of a motor (40); a protection circuit (71) for prohibiting energization of the motor when the motor is in an overload state; and a controller (50) for outputting a command signal for controlling the rotating speed of the motor.例文帳に追加
モータ(40)の回転状態を検出するセンサ(43)と、モータが過負荷状態である場合に、モータへの通電を禁止する保護回路(71)と、モータの回転数を制御するための指令信号を出力するコントローラ(50)と、を有する。 - 特許庁
For stopping fluid injection, or when an injection command from an operator is stopped (No as determined in step S3), the tube clip 31 is closed first (steps S7 and S8), and then driving of a pump 20 and a piezoelectric element 401 are stopped (steps S5 and S6).例文帳に追加
流体噴射を停止するとき、つまり術者からの噴射指令が停止されたときには(ステップS3の判定が“No”)、先ずチューブクリップ31を閉鎖し(ステップS7、S8)、次にポンプ20及び圧電素子401の駆動を停止する(ステップS5、S6)。 - 特許庁
After a new storage tape C is connected to an old storage tape C, a CPU 110 sends a send command to a component supply unit 6, and a servomotor 28 and a driving motor 42 of the supply unit 6 are driven to make component feed operation and the like.例文帳に追加
古い収納テープCに新しい収納テープCを連結した後、部品供給ユニット6にCPU110は送り指令を送り、当該供給ユニット6のサーボモータ28及び駆動モータ42を駆動させて、部品送り動作等を行わせる。 - 特許庁
The magnitude of the current flowing in the electric motor 30 is determined from the potential difference (V2-V1) across both terminals of a resistance 20b connected in series with a grounded circuit of the driving circuit 20, and the direction of current is determined in response to the code of the command current.例文帳に追加
電動モータ30に流れる電流の大きさは、駆動回路20の接地経路に直列接続された抵抗20bの両端の電位差(V2−V1)から求められ、同電流の方向は、前記指令電流の符号に応じて決定される。 - 特許庁
Furthermore, the control part 46 outputs a driving command for a stepping motor 44 to a motor driver 45, a separation cam 43 is rotated, a separation lever 42 is rotated by the rotation of the separation cam 43 and a transfer fixing roller 27 is separated from the intermediate transfer belt 25.例文帳に追加
さらに制御部46は、モータドライバ45にステッピングモータ44の駆動指令を出力し、離間カム43を回転させ、離間カム43の回転により離間レバー42を回転させ、転写定着ローラ27を中間転写ベルト25から離間させる。 - 特許庁
The image fetch-in of the CCD and the shutter operation of the APS are synchronized in the timing of the vertical driving signal of an (n)th pulse (for instance second pulse) after the command of an exposure timing emitted because a release switch is totally depressed is received by the CPU on the side of the DSC.例文帳に追加
DSC側のCPUはレリーズスイッチの全押しにより発せられる露出タイミングのコマンドを受信してから、nパルス( 例えば、2 パルス) 目の垂直駆動信号のタイミングで、CCDの画像取込とAPSのシャッター動作を同期させる。 - 特許庁
After a new storage tape C is connected to an old storage tape C, a CPU 110 sends a feed command to a component supply unit 6, and a servomotor 28 and a driving motor 42 of the supply unit 6 are driven to perform a component feed operation and the like.例文帳に追加
古い収納テープCに新しい収納テープCを連結した後、部品供給ユニット6にCPU110は送り指令を送り、当該供給ユニット6のサーボモータ28及び駆動モータ42を駆動させて、部品送り動作等を行わせる。 - 特許庁
After the first step, and operation-start command signal is outputted to the three servo drivers by a transmission means 26 from the NC controller 21, and the three servo drivers receive the synchronous signal and carry out it to start driving the three servo motors (a second step).例文帳に追加
第1ステップ後、NCコントローラ21から伝達手段26で3台のサーボドライバに動作開始命令信号を出力すると、3台のサーボドライバはその同期信号を受信し実行して、3台のサーボモータを駆動開始する(第2ステップ)。 - 特許庁
When the mode changeover switch 13 is turned on, the control section 16 always operates, turning on the power supply relay 12 of its own device according to a power supply on command and turning on the other device at the same time by outputting the relay driving voltage from the trigger output terminal 17 (master mode).例文帳に追加
モード切換スイッチ13をオンすると制御部16が常時動作し、電源オンコマンドに応じて自装置の電源リレー12をオンするとともにトリガ出力端子17からリレー駆動電圧を出力して他装置もオンする(マスタモード)。 - 特許庁
To provide a solenoid valve driving circuit using an AC power source, capable of solving a problem that a valve opening and closing speed is different in accordance with a command timing from a control device, and quickening the operation of a valve element of a solenoid valve with high repeatability.例文帳に追加
制御装置からの指令タイミングによってバルブ開閉速度が異なるといった問題を解決して、電磁弁の弁体の動作を早く、かつ再現性良く駆動できる交流電源を使用した電磁弁駆動回路を提供する。 - 特許庁
In the meantime, when it is determined as not hierarchical removal (S301: NO), a command from a driving control module is set as a target engine torque (S302), and an ignition timing, a target throttle opening degree and a fuel injection amount are calculated corresponding to the target engine torque (S303).例文帳に追加
一方、階層離脱でないと判断された場合は(S301:NO)、駆動制御モジュールからの指令を目標エンジントルクとし(S302)、目標エンジントルクに応じた点火タイミング、目標スロットル開度、燃料噴射量として算出する(S303)。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|