| 例文 |
driving commandの部分一致の例文一覧と使い方
該当件数 : 807件
In a compressor driving method wherein an inverter 6 controls a synchronous motor 7 that drives a compressor 8, a current limiter 3 is provided so that a current command doesn't exceed an upper limit of a current.例文帳に追加
インバータ6によって同期モータ7を制御し、同期モータ7によって圧縮機8を駆動する圧縮機駆動方法において、電流指令が電流上限値を越えないように制限する電流リミッタ3を設けた。 - 特許庁
Each driving source 11 and 12 is controlled in accordance with these speed command values v1 and v2, and a transfer crane 1 is controlled so as to lower the deviation amount (y) and the deviation angle θaccording to the speed difference between the left and right wheels 7 and 8.例文帳に追加
これらの速度指令値v_1,v_2に応じて各駆動源11,12が制御されてトランスファクレーン1は左右の車輪7,8の速度差によってずれ量yおよびずれ角θが低減するように制御される。 - 特許庁
This controller has a load sensor (14) for detecting the load on a first rotary actuator (13) for driving the crushing mixer (7a) and a controller (10) for controlling the rotation command of the first rotary actuator (13) based on the load detected with the load sensor @{3754/2414).例文帳に追加
破砕混合機(7a)を駆動する第1の回転アクチュエータ(13)の負荷を検出する負荷センサ(14)と、負荷センサ(14)の検出した負荷に基づき、第1の回転アクチュエータ(13)の回転指令を制御する制御器(10)とを備える。 - 特許庁
When no article is purchased and the return command is sent, an introduction destination switching control means 7 drives a driving device 8 to place a gate 8a in operation and distributes the coin 1 to the passage connecting to a return opening.例文帳に追加
導入先切り替え制御手段7は、商品が購入されずに返却指令が送られると、駆動装置8を駆動してゲート8aを動作させ、コイン1を返却口の通じる通路に振り分ける。 - 特許庁
To solve the following problem: only display of curvature information indicating a locus of data of a moving position command included in an NC program or how it changes, as usual, cannot easily grasp moving situations of each driving shaft of a machine.例文帳に追加
従来のようなNCプログラム内に含まれている移動位置指令のデータの軌跡やその変化具合を示す曲率情報の表示のみでは、機械の各駆動軸の移動状況が簡単には把握できない。 - 特許庁
The adjuster part 23 is rotated by using a rotating driving part 13 according to a rotating operation command from an input operation part 13Aa, and the focus adjustment of an on-vehicle camera 20 is performed while confirming the picked-up image of a reference figure 14 by using a display part 12.例文帳に追加
入力操作部13Aaの回転操作指令により回転駆動部13を用いてアジャスタ部23を回転させ、表示部12により基準図形14の撮像画像を確認しながら、車載カメラ20のピント調整を行う。 - 特許庁
The controller 50 outputs display data in j-bit units through 1st to (j)th data output terminals and command data for controlling a data line driving circuit 30 through a (j+1)th data output terminal.例文帳に追加
コントローラ50は、第1〜第jのデータ出力端子を介してjビット単位で表示データを、第(j+1)のデータ出力端子を介してデータ線駆動回路30を制御するためのコマンドデータを出力する。 - 特許庁
If sewing is in process and a motor for a sewing machine is driven (S17:Yes) when a fingertip key for a retreat command is operated, the motor of the sewing machine stops driving with the needle located at the high position (S18, S19:YES).例文帳に追加
タッチキーの退避指令キーが操作されたときに、縫製中であってミシンモータが駆動中のときには(S17:Yes) 、縫針が針上位置となるようにミシンモータの駆動が停止される(S18、S19:Yes) 。 - 特許庁
The lens system 2 is provided with a control means 301 of controlling a focus driving means 11 according to a focus drive command based upon the detection result of the focus adjustment state of a photography optical system.例文帳に追加
レンズ装置2に、カメラ1から送信された、撮影光学系の焦点調節状態の検出結果に基づくフォーカス駆動指令に応じてフォーカス駆動手段11を制御する制御手段301を設ける。 - 特許庁
Then, based on the detected value of the vehicle speed, the damping and driving command values, and the efficiency index, the operating points of an engine 2 and motors 1, 4 are determined in such a way that charge amount to a battery is decreased inversely as the efficiency index becomes large.例文帳に追加
そして、車速検出値、制駆動力指令値および効率指標に基づいて、効率指標が大きいほどバッテリーへの充電量を少なくするエンジン2とモーター1,4の運転点を決定する。 - 特許庁
A fine adjuster 5 outputs a command a driving a car 1 so as to eliminate a landing error detected by a displacement detector 4 when an in-car fine adjuster button 2 or a hall side adjuster button 3 is operated.例文帳に追加
微調整装置5は、かご内微調整釦2またはホール側調整釦3が操作されたとき変位検出器4で検出された着床誤差がなくなるように、かご1を駆動する指令aを出力する。 - 特許庁
A control means controls to raise the frequency f1 of a command signal stepwise for a predetermined time t1 at the time of starting the motor for driving the photoreceptor drum and make it constant after attaining predetermined frequency f2.例文帳に追加
制御手段は、感光体ドラムを駆動するモータの起動時に指令信号の周波数f1をある所定時間t1で段階的に上げていき、所定の周波数f2になった後、一定とするように制御する。 - 特許庁
This multirelay is equipped with a breaker 101 which supplies electricity to a motor 106 driving plant equipment, and an operation/stop command is sent from a controller 119 to the motor through a control CPU 113 and a contactor 105.例文帳に追加
プラント機器を駆動するモータ106に電気を供給する遮断器101を備え、コントローラ119からモータに対する運転/停止指令は制御CPU113と接触器105を介して送信される。 - 特許庁
This internal combustion engine 1 has a variable valve train 26 driven by hydraulic pressure generated on the basis of rotational driving of the internal combustion engine 1 and driven in a state suitable for starting the engine after detecting the engine stopping command.例文帳に追加
内燃機関1は、内燃機関1の回転駆動に基づいて発生する油圧により駆動され、機関停止指令の検出後に機関始動に適した状態に駆動される可変動弁機構26を備える。 - 特許庁
In the elevator controlling apparatus for performing a PWM control using a carrier frequency signal to control an AC motor (3) for driving an elevator car (22), a carrier frequency switching circuit (8) reduces the frequency of a carrier signal when a torque command value for driving the AC motor (3) reaches a predetermined torque limit value.例文帳に追加
キャリア周波数信号を用いてPWM制御し、交流電動機(3)に制御して、エレベータかご(22)を駆動するエレベータの制御装置において、キャリア周波数切替え回路(8)は、交流電動機(3)を駆動するトルク指令値が所定のトルク制限値に達したときに、キャリア信号の周波数を下げる。 - 特許庁
A detection command signal is outputted from a control circuit 14 to a detecting means so that a position of the hand is detected by providing a predetermined relationship with timing of a pulse signal inputted from the control circuit 14 to a winding leading terminal 121b' and a winding trailing terminal 121b" of the driving coil 121b for driving the rotor 121c.例文帳に追加
さらに、駆動コイル121bの巻始め端子121b’と巻終わり端子121b’’に入力される、制御回路14からのロータ121cの駆動のためのパルス信号のタイミングと所定の関係を持たせて指針の位置検出を行うように、検出指令信号を制御回路14から検出手段に出力する。 - 特許庁
The starting controller includes an operation point command part 400 which conducts the feedback control for a motor generator MG based on a rotational difference between a target motor rotational frequency corresponding to a target driving force tFoO and an actual motor rotational frequency, and corrects a target engine torque corresponding to the target driving force tFoO based on the rotational difference.例文帳に追加
エンジン始動によるWSC走行モードでの発進時、目標駆動力tFoOに応じた目標モータ回転数と実モータ回転数との回転差に基づいてモータジェネレータMGをフィードバック制御すると共に、回転差に基づいて目標駆動力tFoOに応じた目標エンジントルクを補正する動作点指令部400を設けた。 - 特許庁
When displaced to the azimuth angle and the tilt angle indicated in the drawing by this device 1, a driving command is issued to a driving motor 9 on the basis of azimuth angle directional wind direction information detected by a wind direction detector installed on the windmill 2, and thus, a nacelle 4 rotates so that a rotor shaft 5a turns to a certain azimuth angle.例文帳に追加
本装置1により、同図に示すような方位角及びチィルト角に変位させる場合、風車2に取り付けられた風向き検知器により検知された方位角方向の風向き情報に基づき駆動モータ9に駆動指令が発せられ、これにより、ナセル4は、ロータ軸5aがある方位角を向くように回転する。 - 特許庁
In the process mode, the voltage according to the execution process content is applied by controlling the driving power section 3 based on a command from outside and in the picture-output mode, the starting control is performed appropriately by displaying the input image promptly by controlling the driving power section 3 based on a predetermined sequence.例文帳に追加
プロセスモードの場合には、外部からのコマンドに基づいて駆動電源部3を制御して、実行プロセス内容に応じた電圧を印加し、絵だしモードの場合には、所定のシーケンスに基づいて駆動電源部3を制御して、速やかに入力映像を表示することにより、立ち上げ制御を好適に行うことができる。 - 特許庁
That is, a controller controls the rotation so that the carrier roller operates in response to the target speed locus by adjusting an electric current command value Ir to a driving circuit for driving the motor based on a deviation between the target speed locust and a detecting speed, and achieves carrying control of the sheet corresponding to the target speed locus.例文帳に追加
即ち、制御器は、目標速度軌跡と検出速度との偏差に基づき、モータを駆動する駆動回路への電流指令値Irを調整することにより、搬送ローラが目標速度軌跡に従って運動するように回転制御し、目標速度軌跡に対応したシートの搬送制御を実現する。 - 特許庁
The relative positional relationship between a speed change link and a connecting member is adjusted so that the actual inclined rotation angle ϕ after driving a step motor to a preset geared neutral point command point in a state of driving a continuously variable transmission with an infinite speed change ratio becomes within a preset adjustment range ±β across the geared neutral point GNP.例文帳に追加
変速比無限大無段変速機を運転した状態で、ステップモータを予め設定したギアードニュートラルポイント指令位置へ駆動してから、実際の傾転角φがギアードニュートラルポイントGNPを挟んで予め設定した調整範囲±β内となるように変速リンクと連結部材の相対位置関係を調整する。 - 特許庁
In the idling preventing control device 23 for a trolley to travel on a girder with the wheels, the driving torque of a trolley motor 21 for driving the wheels is determined depending on the wheel pressure of the wheels based on a hoisted load, and a determined command is output to a trolley motor controller 22 which controls the trolley motor 21.例文帳に追加
車輪によってガーダ上を走行するトロリの空転防止制御装置23であって、前記車輪を駆動するトロリモータ21の駆動トルクが、吊荷に基づく前記車輪の輪圧に応じて決定され、決定された指令が、前記トロリモータ21を制御するトロリモータ制御器22に出力される。 - 特許庁
The shift lens drive control part 104 is provided with an vibration-proofing control part 201 for outputting a position command signal, Hall elements 204 and 205 for detecting the position of the shift lens unit 103 in a pitch direction and a yaw direction, and also, outputting the position signal, and driving parts 213 and 214 for driving the shift lens unit 103.例文帳に追加
シフトレンズ駆動制御部104は、位置指令信号を出力する防振制御部201と、シフトレンズユニット103のピッチ方向及びヨー方向の位置を検知すると共に位置信号を出力するホール素子204,205と、シフトレンズユニット103を駆動するドライブ部213,214とを備える。 - 特許庁
The slave control device (a presentation control device 40) starts an initialization processing in such a state that the electric drive source (a generator driving motor 41) is not driven based on activation of the power supply of the game machine 100, and executes a processing for initializing the electric driving source when a storage completion command is received.例文帳に追加
また、従属制御装置(演出制御装置40)は、当該遊技機100の電源の投入に基づき電気的駆動源(役物駆動モータ41)を駆動させない状態で初期化処理を開始し、記憶完了指令を受信すると電気的駆動源を初期状態にする処理を行うようにする。 - 特許庁
The subtraction part 23 and the engine control part 25 drive the driving motor 26 based on a value calculated by subtracting the target driving force calculated by the torque command calculation part 21 when traction control is operated, and control the engine 28 for power generation with a target engine revolution speed value when the traction control is not operated.例文帳に追加
減算部23及びエンジン制御部25は、トラクションコントロール作動時に、トルク指令演算部21が算出した目標駆動力を減算した値に基づいて、駆動モータ26を駆動させるとともに、トラクションコントロールが作動していない場合のエンジン回転数目標値で発電用エンジン28を制御する。 - 特許庁
Thereafter, a variable structure driving part 23 calculates a motor driving torque command value required for realizing the target lateral displacement amount of the variable structure from the target lateral displacement amount of the variable structure, the yaw rate Φ, the forward and backward acceleration α_xT, the lateral acceleration α_yT, and the motor rotation angle ϕ, so as to output it to a servo driver for a motor.例文帳に追加
その後可動構成物駆動部23で、上記可動構成物の目標横変位量と、上記ヨーレートΦ、前後加速度α_xT、横加速度α_yT、およびモータ回転角φとから、可動構成物の目標横変位量を実現するのに必要なモータ駆動トルク指令値を算出し、これをモータ用サーボドライバへ出力する。 - 特許庁
To solve the following problem that arises when an alternating current signal is added to a q-axis current command to forcedly produce a high-frequency torque ripple in a variable-speed driving device for synchronous motors: when a voltage component becomes higher than the outputtable maximum voltage of an inverter, voltage saturation occurs and thus it is impossible to accurately generate a current command.例文帳に追加
同期電動機の可変速駆動装置において、q軸の電流指令に交流信号を加算して高周波のトルクリップルを強制的に発生させる場合、電圧成分がインバータの出力可能最大電圧よりも大きくなると電圧飽和が発生するため電流指令を正確に発生することができなくなる問題を有している。 - 特許庁
An active damping system is provided with a variable dynamic compensator 10 whose compensation characteristics change by a variable αfrom response amounts X_1-XN for obtaining a drive command voltage U (α) and a driving device control circuit 4 for controlling the drive of a damping device 5 on the basis of the drive command voltage U (α) obtained by the variable dynamic compensator 10.例文帳に追加
アクティブ制振システムは、応答量X_1〜X_Nから、変数αによりその補償特性が変化し、駆動指令電圧U(α)を求める可変式動的補償器10と、可変式動的補償器10が求めた駆動指令電圧U(α)に基づいて制振装置5の駆動を制御する駆動装置制御回路4とを備えている。 - 特許庁
This optical disk master disk exposing device controls the driving of the spindle motor and a slider in every rotation of the spindle with a spindle rotation command pulse train and a slider movement command pulse train generated by dividing a pulse train of basic clocks whose number is proportional to ideal line length determined by the start radius position of a spiral, the number of tracks, and spiral track pitch.例文帳に追加
本発明の光ディスク原盤露光装置は、スピンドル1回転毎に、スパイラルの開始半径位置、トラック数及びスパイラルトラックピッチにより定まる理想的線路長に比例した数の基本クロックのパルス列を分周して生成したスピンドル回転指令パルス列及びスライダ移動指令パルス列によりスピンドルモータ及びスライダの駆動を制御する。 - 特許庁
This driving circuit is one related to a sensorless motor, which puts the motor in reverse torque brake condition by adding a brake command signal to a current application logic circuit 77, counts up a counter circuit 89 to generate a count signal, and stops the drive current to a drive coil with the count signal and the signal of the brake command, thereby breaking the drive torque.例文帳に追加
通電ロジック回路77にブレーキ指令信号を加え逆トルクブレーキ状態にしモータの回転速度が十分に低下したとき、前記カウンタ回路89をカウントアップし、カウント信号を発生させ、そのカウント信号とブレーキ指令の信号で駆動コイルへの駆動電流を停止し駆動トルクを遮断するセンサレスモータに関する。 - 特許庁
The driving wheel controller 20 has a controlling and calculating part calculating the current value of the current supplied to the motor 6 based on angle signals and axial force signals and outputting command signals, and a driver part controlling the current supplied from the secondary battery 5 to the motor 6 based on the command signals supplied from the controlling and calculating part.例文帳に追加
駆動輪制御装置20は、角度信号および軸力信号に基づき、電動機6に供給される電流の電流値を演算し、指令信号を出力する制御演算部と、制御演算部から供給される指令信号に基づき、2次電池5から電動機6に供給される電流を制御するドライバ部とを有する。 - 特許庁
This user support system includes an operating system 2a which outputs a command for driving a CD/DVD-ROM device 5 and detects the execution result of the command, a user support software 2b, a device driver software 2c, a RAM 2 which records the detection result of the system 2a and a CPU 1 which outputs the recording result.例文帳に追加
CD/DVD−ROMデバイス装置5を駆動するためのコマンドを出力し、出力されたコマンドの実行結果を検知するためのオペレーティングシステム2a、ユーザ支援ソフトウェア2b、デバイスドライバソフトウェア2cと、検知の結果を記録するRAM2と、記録の結果を出力するためのCPU1とを備えたことを特徴とするユーザ支援システム。 - 特許庁
According to the wheel driving force allocation controlling system 90, when the detection signal related to the throttle opening m shows abnormality, a pre-torque Tp (first torque command value) is invalidated, and a transmission torque based only on a rotation difference torque Tn (second torque command value) related to a rotation speed difference ΔN between front wheels 14 and rear wheels 15 is transmitted to the rear wheels 15, 15.例文帳に追加
本発明の車輪駆動力配分制御システム90によれば、スロットル開度mに係る検出信号が異常状態になった場合には、プレトルクTp(第1トルク指令値)が無効化されて、前後輪14,15の回転速度差ΔNに係る回転差トルクTn(第2トルク指令値)のみに基づく伝達トルクが後輪15,15に伝達される。 - 特許庁
The deviation generator 40 calculates a deviation d between a current command value Ic to a stepping motor 30 and a driving current value Id flowing in the stepping motor 30 to generate a current value deviation D obtained by applying a predetermined gain G to the calculated deviation d.例文帳に追加
偏差生成部40は、ステッピングモータ30に対する電流指令値Icとステッピングモータ30に流れる駆動電流値Idとの偏差dを求め、偏差dに所定のゲインGを与えた電流値偏差Dを生成する。 - 特許庁
A light transmitting path 15 transmits the image information from the imaging part and the attitude information from the angle detecting part by optical communication to the storage part by combining those information for each frame, and transmits the control command by the optical communication to the scanning driving part.例文帳に追加
光伝送路15は、撮像部からの画像情報と角度検出部からの姿勢情報とをフレーム毎に組み合わせて光通信により記憶部に送信し、且つ制御指令を光通信により走査駆動部に送信する。 - 特許庁
This auger type ice maker has a geared motor being a driving means of an auger, and an arching predicting means for predicting the occurrence of arching from an operation damping state of the auger or an integrally rotating part with the auger, after issuing a stopping command to the geared motor.例文帳に追加
オーガ式製氷機は、オーガの駆動手段であるギヤードモータと、ギヤードモータへの停止命令が発せられた後、オーガ又はそれと一体的回転部の動作減衰状態からアーチング発生を予知するアーチング予知手段とを備える。 - 特許庁
An inverter apparatus 3 is equipped with: a torque limit portion 11 that limits a torque command value for a motor 5 so that the switching element temperature Tj of the inverter 2 that controls driving of the motor 5 is suppressed to an element upper limit temperature TL1 or below.例文帳に追加
インバータ装置3は、電動機5を駆動制御するインバータ2のスイッチング素子温度Tjが、素子上限温度TL1以下に抑制されるよう電動機5のトルク指令値に制限を加えるトルク制限部11を備える。 - 特許庁
In the discharge control circuit, a prescribed discharge operation command (signal for driving a safe solenoid) is outputted (steps S58 and 59) to a safe unit based on the received difference number normality notification and safe balls are discharged.例文帳に追加
排出制御回路106Aでは受信した差数正常通知に基づいてセーフユニット111に所定の排出動作指令(セーフソレノイド151を駆動する信号)を出力(ステップS58、59)してセーフ球を排出させる。 - 特許庁
Even when variation of the detected value VLR becomes zero, in the case when a difference exists between the detected value VLR and the target value VLA, the driving duty ratio DVL at the time is learned and renewed as a holding command value KVL.例文帳に追加
検出値VLRの変化量が「0」となっても、同検出値VLRと目標値VLAとの間に差が存在する場合には、その時の駆動デューティ比DVLを保持指令値KVLとして学習更新する。 - 特許庁
In a temperature controller system shown by the example of a figure 3, the temperature of a control object 11 arranged at the A side of a Peltier element 12 is controlled by using a command voltage from a control unit 15 as the driving voltage of a Peltier element 12.例文帳に追加
図3の例の温度制御装置システムにおいては、制御機15からの指令電圧をペルチェ素子12の駆動電圧として、そのペルチェ素子12のA面側に配置される制御対象11の温度を制御する。 - 特許庁
An engine ECU 50 learns a base duty ratio command value of an actuator 22a driving a throttle valve 22 which is an engine operation quantity as one of conditions where the idling target speed enters a predetermined rotation speed zone during idling operation.例文帳に追加
エンジンECU50は、アイドル運転中にアイドル目標回転数が所定の回転数域に入ることを条件の一つとして、エンジン操作量であるスロットルバルブ22を駆動するアクチュエータ22aの基本デューティ比指令値を学習する。 - 特許庁
To provide a semiconductor disk device that can reliably store data sent by a writing command from a central processing unit and temporarily stored in a buffer, even if driving voltage fails.例文帳に追加
駆動電圧に異常が生じた場合においても、中央処理装置からの書き込み指令に基づき送出され、バッファに一時的に蓄積されている状態のデータを確実に格納することのできる半導体ディスク装置の提供。 - 特許庁
To output the command signal of motor driving to a motor from a speed controller for prescribed time after abnormality occurs if abnormality occurs in a sensor even if the hardware and the software of the speed controller is not altered.例文帳に追加
速度制御装置のハードやソフトに何等改造を行わなくても、センサ等に異常が生じた場合に異常発生後一定時間の間は速度制御装置からモータへモータ駆動の指令信号を出力し得るようにする。 - 特許庁
The controller responds to a command which is given from an external part, controls the driving of the light-emitting element, displays a state during a memory access operation and displays the free capacitance of the memory, based on sector management information of the memory.例文帳に追加
コントローラは、外部から与えられるのコマンドに応答して、前記発光素子を駆動制御して、前記メモリアクセス動作中の状態を表示し、また、メモリのセクタ管理情報に基づいてメモリの空き容量の状態を表示する。 - 特許庁
The airbag housing container 11 projects between the driver's seat 1D and the front occupant's seat 1P by an action of the driving motor with an action command from a control unit when the control unit receives pre-collision condition information from a distance measuring sensor 4.例文帳に追加
エアバッグ格納容器11は、制御部が測距センサ4から衝突前状態情報を受けた場合に、制御部からの動作指令により駆動モータの動作で運転席1Dと助手席1Pとの間に突出する。 - 特許庁
When the reference value is not exceeded, in a step S6, the amount of fluctuation IH (Ta) of a driving current command value which is based on the environmental temperature Ta, and the amount of current decrease IST (ST, dST) which is determined by deterioration of the element are operated.例文帳に追加
基準値を超えない場合にはステップS6で周囲温度Taに基づく駆動電流指令値の変動量IH(Ta)と素子の劣化によって決まる電流低下量IST(ST,dST)を演算する。 - 特許庁
When a potentiometer for continuously detecting the position of the range selection value has trouble (S5), the operation condition is shifted to the fail-safe state when driving of the actuator is stopped (S6), a warning on the abnormality of the sensor is given, and a command to operate an emergency switch is given (S7).例文帳に追加
レンジ切換バルブの位置を連続的に検出するポテンショメータが故障すると(S5)、アクチュエータ駆動を停止させるフェイルセーフ状態に移行させる一方(S6)、センサ異常を警告し、かつ、非常スイッチの操作を指示する(S7)。 - 特許庁
The branched driving part 48 is changed over and controlled based on detection of shoe by the shoe detection part 47 connected with the branched control part 42 by a branch command from the main control part 41 to perform stable branch operation without affected by conveyance speed of the sorting conveyor 21.例文帳に追加
主制御部41からの分岐指令で、分岐制御部42に接続したシュー検知部47によるシューの検知に基づき、分岐駆動部48を切換制御し、仕分コンベヤ21の搬送速度に影響なく安定した分岐動作ができる。 - 特許庁
A rotary electric machine driving system 10 includes a power supply circuit 20 having the rotary electric machine 12, an electricity accumulating unit 22, a voltage converter 24 and an inverter 26, a command value generating part 30 and a rotary electric machine controller 40.例文帳に追加
回転電機駆動システム10は、回転電機12と、蓄電装置22と電圧変換器24とインバータ26を有する電源回路20と、指令値生成部30と、回転電機制御装置40とを備えて構成される。 - 特許庁
The galvanic scanner system 1 is equipped with a galvanic scanner 2 and a scanner driver 3 to drive the scanner, wherein the scanner driver 3 is loaded with a command generating microcomputer 5 in which digital data expressing the driving pattern of the scanner 2 are written.例文帳に追加
ガルバノ型スキャナシステム1は、ガルバノ型スキャナ2と、これを駆動するスキャナドライバ3とを有し、スキャナドライバ3には、スキャナ2の駆動パターンを表すデジタルデータが書き込まれた指令発生用マイクロコンピュータ5が搭載されている。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|