1153万例文収録!

「21」に関連した英語例文の一覧と使い方(468ページ目) - Weblio英語例文検索


小窓モード

プレミアム

ログイン
設定

設定


セーフサーチ:オン

不適切な検索結果を除外する

不適切な検索結果を除外しない

セーフサーチについて

21を含む例文一覧と使い方

該当件数 : 49989件



例文

A rod guide 24 is provided on an outer periphery side of the piston rod 21, and a seal member for sealing between the tube 17 and the piston rod 21 is provided on the lower side of the rod guide 24.例文帳に追加

また、チューブ17の下側には、ピストンロッド21の外周側に位置してロッドガイド24を設け、ロッドガイド24の下側にはチューブ17とピストンロッド21との間をシールするシール部材28を設けている。 - 特許庁

A reticle stage 15 is provided with an electrostatic chuck 21 for electrostatically sucking a reticle R, and holder sections 35 are provided on both ends, in an X direction and a counter-X direction of the electrostatic chuck 21, respectively.例文帳に追加

レチクルステージ15は、レチクルRを静電吸着する静電チャック21を備え、該静電チャック21のX方向及び反X方向の両端部には、ホルダ部35がそれぞれ設けられている。 - 特許庁

When brake is to be applied, friction pad 8 is pressed to a disc through an outer shim plate 21 and an inner shim plate 11, wherein the outer shim plate 21 is slided relative to the inner plate 11.例文帳に追加

ブレーキの操作時には、外側シム板21、内側シム板11を介して摩擦パッド8をディスクに押圧し、このとき外側シム板21を内側シム板11に対して相対的にスライドさせる。 - 特許庁

In the refrigerant circuit 10, two booster compressors 41 compressing in two stages are connected with an outdoor compressor 21 in parallel with each other, and a supercooling heat exchanger 51 for liquid refrigerant is mounted in communication liquid piping 13.例文帳に追加

冷媒回路(10)には、室外圧縮機(21)との間で2段圧縮するブースタ圧縮機(41)が2台並列に接続され、連絡液配管(13)に液冷媒の過冷却熱交換器(51)が設けられている。 - 特許庁

例文

The brake member 26 is made of a single material and has a spring portion 263 to impose a load on the rotation of the film feeding reel 21 by pressing the end area of the film feeding reel 21.例文帳に追加

ブレーキ部材26は、単一の材質製であり、フィルム供給リール21の端部領域を押圧することでフィルム供給リール21の回転方向に負荷を与えるバネ部263を備えている。 - 特許庁


例文

When a voltage drop across a choke coil 7 decreases and becomes the predetermined value or less, a gate voltage breaking circuit 21 breaks a gate voltage supplied to a commutating MOS FET 6.例文帳に追加

チョークコイル7の両端間の電圧降下が小さくなり、この電圧降下が所定値以下になると、ゲート電圧遮断回路21は転流MOS型FET6へのゲート電圧の供給を遮断する。 - 特許庁

The projections 10a-10b locate closer to the center than the edge of the disk 21 when the optical beam converged by the objective lens 1 irradiates the outermost periphery of the disk 21.例文帳に追加

さらに突起部10a,10bは、対物レンズ1によって集光した光ビームが光ディスク21の最外周部を照射するときに、光ディスク21のエッジよりも該光ディスク21の中心側に位置する。 - 特許庁

An odd-numbered memory cell among memory cells arranged in the column direction is connected to the bit line 36 via a switch 21, and an even-numbered memory cell is connected to the bit line 35 via the switch 21.例文帳に追加

列方向に配列されるメモリセルのうち奇数番目のメモリセルはスイッチ21を介してビット線36に接続され、その偶数番目のメモリセルはスイッチ21を介してビット線35に接続されている。 - 特許庁

A bottom plate 21 of the supporting stand 17 is manufactured as an injection-molded article made of a synthetic resin, and includes vertical webs and horizontal webs for placing the inside container 2 and reinforcing the bottom plate 21.例文帳に追加

支台17の底板21は合成樹脂製射出成形品として製作され、かつ内側容器2を載置し底板21を補強するための縦方向ウェブおよび横方向ウェブを備えている。 - 特許庁

例文

The resin projection 18 includes a lower surface 19 facing the semiconductor substrate 10, an upper surface 21 turned opposite from the semiconductor substrate 10 and a side face 23 connecting the lower surface 19 and the upper surface 21 together.例文帳に追加

樹脂突起18は、半導体基板10と対向する下面19と、半導体基板10とは反対を向く上面21と、下面19及び上面21を接続する側面23と、を含む。 - 特許庁

例文

The touch panel 21 displays a sub menu to customize functions allocated to the operating buttons of the operating section 11 of an electronic scope 10 and customize a display language and brightness of the touch panel 21.例文帳に追加

また、タッチパネル21には、電子スコープ10の操作部11の操作ボタンに割当てられる機能のカスタマイズやタッチパネル21の表示言語及び輝度のカスタマイズを行うためのサブメニューが表示される。 - 特許庁

When assembling, the threaded holes 21 of the fitting bar 20 are selected according to fitting positions, and fitting parts such as a shelf 25 and a mount 26 are screwed to the fitting bar 20 in the threaded holes 21.例文帳に追加

そして、組付け時は、取付位置に応じて取付バー20のねじ穴21を選んで、そのねじ穴21において棚25や取付台26などの取付部品を取付バー20にねじ付ける。 - 特許庁

The sealing member 23 is set between the end of the tubular body 21 and the valve presser member 22, and seals the space between the tubular body 21 and the fiberscope 30 as pressed to the fiberscope 30 side.例文帳に追加

シール部材23は、筒状本体21の端部と弁押さえ部材22との間に設置されファイバースコープ30側に押圧されることにより筒状本体21とファイバースコープ30との間をシールする。 - 特許庁

The drive device 10 for the variable valve lift mechanism includes a metal worm 21 having a spiral groove, and a resin wheel 25 including teeth 26 corresponding to the groove formed at the worm 21.例文帳に追加

バルブリフト可変機構用駆動装置10は、螺旋状に溝が設けられた金属製のウォーム21と、ウォーム21に設けられた溝に対応する歯部26を有する樹脂製のホイール25とを備えている。 - 特許庁

Bolt rods 21 are connected to the anchor bolts 12 through nuts 20 to form the required stages of multistage pipelines on the first stage pipelines through the bolt rods 21, pipe cushions 15, 16 and pipe presser members 13.例文帳に追加

この管路A_1 の上には、アンカーボルト12にナット20を介しボルト棒21を連結し、このボルト棒21、管枕15、16及び管押え13を介して所要段の管路A_2 、A_3 ……を形成する。 - 特許庁

A supporting lip 21 is projected from the bottom lip 17 toward a bottom wall 8c of the glass run body 8, and an intermediate portion in the extending direction of the bottom lip 17 is elastically backed up by the supporting lip 21.例文帳に追加

また、そのボトムリップ17からグラスラン本体8の底壁部8cに向けて支持リップ21を突設し、その支持リップ21をもってボトムリップ17の延出方向中間部を弾性的にバックアップする。 - 特許庁

In the recess 21 of a basic body 2, an AFE element 51 and a TG element 61 are fixed while connecting its pad electrodes 52 and 62 with wiring 3A formed inside the recess 21.例文帳に追加

基体2の凹部21には、AFE素子51およびTG素子61が、そのパット電極52およびパット電極62と、凹部21の内側に形成された配線部3Aとが接続されて取り付けられている。 - 特許庁

The projections 10a-10d are formed at the positions overlapping the objective lens 1 in the circumferential direction on the optical disk 21, and at the positions radially overlapping the objective lens 1 on the optical disk 21.例文帳に追加

これら突起部10a〜10dは、光ディスク21の円周方向で対物レンズ1に重なる位置、及び光ディスク21の半径方向で対物レンズ1に重なる位置に複数設けられる。 - 特許庁

A recess 21 is formed as an axial directional insertion part on an end surface 20 on the piston rod 3 side of a piston 4, and the tip of the rod 3 is inserted into the recess 21 of the piston 4 to ensure a coaxial property.例文帳に追加

ピストン4のピストンロッド3側の端面20に軸方向の嵌め合い部として凹所21を形成し、ピストン4の凹所21にピストンロッド3の先端を嵌入して同軸性を確保する。 - 特許庁

In a stripper plate 21 in a punch die, a workpiece pressing face 23 on the workpiece pressing side in the stripper plate 21 is formed in a convex spherical shape having a large radius of curvature.例文帳に追加

パンチ金型におけるストリッパープレート21であって、上記ストリッパープレート21においてワークを押圧する側のワーク押圧面23が曲率半径の大きな凸状の球面形状に形成してある。 - 特許庁

After that, an instruction for calculating the correction data is input to an analog circuit 25, and an input analog signal SAi of the RF amplifier 21 is output to both the RF amplifier 21 and the receiver.例文帳に追加

その後、補正用データを算出するための命令をアナログ回路25に入力し、RFアンプ21の入力アナログ信号SAiを、RFアンプ21と受信器との両方に出力する。 - 特許庁

The cassette carrying type machining device 1 has a pair of a first punch 21 and a second punch 22 for machining the work and a cassette 4 for holding the work which is capable of advancing/retreating between both punches 21, 22.例文帳に追加

カセット搬送式加工装置1は,ワークの加工を行う一対の第1パンチ21及び第2パンチ22と,両パンチ21,22の間に進退可能なワーク保持用のカセット4とを有している。 - 特許庁

The servant 20 supplies mail sending together with the corresponding arguments to an external application for mail 21 (x3), and the external application for mail 21 sends the corresponding mail to the SMTP server (x4).例文帳に追加

サーバント20は、対応する引数とともにメール送信をメール用外部アプリケーション21に供給し(x3)、メール用外部アプリケーション21は対応するメールをSMTPサーバに送信する(x4)。 - 特許庁

During the high load combustion, the premixed gas 10 passing through the fixed layer 22 further passes through the movable layer 21 while suspending the first heat resistant spheres constituting all or part of the movable layer 21.例文帳に追加

高負荷燃焼時においては、固定層22を通過した予混合ガス10が更に可動層21の一部又は全部を構成する第1耐熱性球体を浮遊させつつ当該可動層21を通過する。 - 特許庁

The catheter body 21 is formed with a sensor lumen 211 into which an imaging core 3 is inserted, and a guide wire lumen 212 into which the guide wire 200 is inserted, along the longitudinal direction of the catheter body 21.例文帳に追加

カテーテル本体21には、イメージングコア3が挿入されるセンサルーメン211と、ガイドワイヤ200が挿入されるガイドワイヤルーメン212とがカテーテル本体21の長手方向に沿って形成されている。 - 特許庁

In an engine 10, an electromagnetic actuation type fuel injection valve 21 is provided on a cylinder block of each cylinder, and fuel is directly injected into a combustion chamber by the fuel injection valve 21.例文帳に追加

エンジン10において、各気筒のシリンダブロック20には電磁駆動式の燃料噴射弁21が設けられており、該燃料噴射弁21により燃焼室22内に燃料が直接噴射される。 - 特許庁

After a light-emitting diode 20, a resistor 21, a Zener diode 22, and a terminal 103 are held integrally temporarily by a holder 102 respectively, the light-emitting diode 20, the resistor 21, the Zener diode 22, and the terminal 103 are soldered.例文帳に追加

発光ダイオード20、抵抗21、ツェナーダイオード22、端子103をそれぞれにホルダ102に仮に一体的に保持した後、発光ダイオード20、抵抗21、ツェナーダイオード22、端子103を半田付けする。 - 特許庁

The processor receives the sensor signal, analyzes the sensor signal based upon an instruction set to determine the pointing vector 21 of the user, and configures the user interface 16 based upon the pointing vector 21 of the user.例文帳に追加

このプロセッサは、センサ信号を受信して、センサ信号を命令セットに基づいて分析してユーザのポインティングベクトル21を決定し、ユーザのポインティングベクトル21に基づいてユーザインタフェース16を設定する。 - 特許庁

When the pedal 15 is depressed, the motion is transmitted to the one-way sprocket 21 by the rod-like member 23 and is converted into the rotary motion of the axle 12 by the one-way sprocket 21.例文帳に追加

ペダル15を踏み込むと、その運動が棒状部材23によって一方向スプロケット21に伝達され、更に一方向スプロケット21によって車輪軸12の回転運動に変換される。 - 特許庁

A translucent electrode 21 of an ITO is formed on the substantially whole surface of the p^+-type GaN layer 16, and a pad electrode 22 of gold is formed on a part of the translucent electrode 21.例文帳に追加

p^+型GaN層16には、ITOから成る透光性電極21がほぼ全面に形成され、透光性電極21上の一部に金から成るパッド電極22が形成されている。 - 特許庁

The semiconductor module includes components such as a semiconductor chip 11 covered by a thermosetting resin mold 21 for ensuring heat resistance, and the outer edge of the thermosetting resin mold 21 is covered by a thermoplastic resin mold 22.例文帳に追加

半導体チップ11等の構成部品を熱硬化性樹脂モールド部21にて覆うことで耐熱性を確保しつつ、熱硬化性樹脂モールド部21の外縁部を熱可塑性樹脂モールド部22にて覆う。 - 特許庁

The circuit 23 converts the digital video data into an analog electric signal to output it to the magnetic head 21 via the video signal processing circuit 22 and then the head 21 transmits a magnetic signal to the magnetic head 11.例文帳に追加

ビデオキャプチャ回路23は、デジタル映像データをアナログ電気信号に変換し、映像信号処理回路22を経由して磁気ヘッド21に出力し、磁気ヘッド11に対して磁気信号を送出する。 - 特許庁

Indium composition Y of the second well layer 23 is smaller than indium composition X of the first well layer 21, and thickness D_W2 of the second well layer 23 is greater than thickness D_W1 of the first well layer 21.例文帳に追加

第2の井戸層23のインジウム組成Yは第1の井戸層21のインジウム組成Xより小さく、また第2の井戸層23の厚さD_W2は第1の井戸層21の厚さD_W1より厚い。 - 特許庁

When pressure in the condenser 9 gets lower than valve opening pressure of the second check valve 21, the second check valve 21 opens and liquid cooling water in the reservoir tank 16 flows into the condenser 9.例文帳に追加

凝縮器(9)内の圧力が第2チェック弁(21)の開弁圧を下回ると第2チェック弁(21)が開弁し、リザーブタンク(16)内の液体の冷却水が凝縮器(9)内へ流入する。 - 特許庁

A projector 21 projects image light including circularly polarized light with a polarization state which differs for each wavelength band, and the projector 21 has a liquid crystal projector 21a and a quarter-wave retardation plate 22.例文帳に追加

投影機21は、波長帯域ごとに異なる偏光状態を持つ円偏光を含む映像光を出射するものであり、液晶プロジェクター21a及び1/4波長位相差板22を有している。 - 特許庁

The first electrode 21 and the second electrode 22 apply to the charged fluid 11 a force proportional to square of the electric field applied on the charged fluid 11 between the first electrode 21 and the second electrode 22.例文帳に追加

第一の電極21及び第二の電極22は、第一の電極21と第二の電極22との間の荷電流体11に加えた電界の二乗に比例する力を荷電流体11に与える。 - 特許庁

The braking device includes a striker bolt 21 screwed penetrating the armature 13, and a resin sleeve 24 that thermally expands is interposed between the striker bolt 21 and the armature 13.例文帳に追加

制動装置は、アーマチュア13を貫通して螺合したストライカーボルト21を有し、ストライカーボルト21とアーマチュア13の間に熱膨張する樹脂スリーブ24を介在させたことを特徴としている。 - 特許庁

A timing adjustment circuit T1 comprising a capacitor C1 is connected between an input terminal (node N13) of the first level converter circuit 21 and the output terminal (node N14) of the first level converter circuit 21.例文帳に追加

第1レベルコンバータ回路21の入力端子(ノードN13)と、第1レベルコンバータ回路21の出力端子(ノードN14)との間にコンデンサC1からなるタイミング調整回路T1を接続した。 - 特許庁

The first pump 21 and the second pump 22 are driven in a state that their phases are shifted from one another to make a flow rate constant of the functional fluid supplied to the actuator 1 from the both pumps 21, 22.例文帳に追加

ここで、第1のポンプ21と第2のポンプ22は、互いに位相をずらして駆動することにより、両ポンプ21,22からアクチュエータ1へ供給する機能性流体の流量を一定とする。 - 特許庁

A throttle valve 21 is inserted in a cylindrical valve chamber 24, orthogonally crossing with a suction passage 1 penetrating the carbureter main body 2 and the turning and shaft movement are produced on the throttle valve 21 by the turning of a throttle valve lever 5.例文帳に追加

気化器本体2を貫通する吸気路1と直交する円筒形の弁室24に絞り弁21を嵌挿し、絞り弁レバー5の回動により絞り弁21に回動と軸移動を生じさせる。 - 特許庁

Respective cementing bodies 21 to 23 are interposed between respective lenses 11 to 14, and cemented with the surfaces of the respective lenses 11 to 14, whereby the respective lenses 11 to 14 and the respective cementing bodies 21 to 23 are integrated.例文帳に追加

各接合体21〜23が各レンズ11〜14間に介在して、各接合体21〜23が各レンズ11〜14表面に接合し、各レンズ11〜14及び各接合体21〜23が一体化している。 - 特許庁

Concretely, after an organic film 21 is prepared on a shaft surface 20, the surface of the organic film 21 is covered with a surface treatment agent having oil repellent ability to form an oil repellent film 22.例文帳に追加

具体的には、軸表面20に有機薄膜21が調製された後、その有機薄膜21の表面に撥油性を有する表面処理剤が被覆され、撥油性被膜22が形成される。 - 特許庁

The coat PC steel stand includes a PC steel strand 20, a thermosetting resin coating layer formed on the surface thereof and granular bodies 22 embedded so as to partially project from the coating layer 21.例文帳に追加

PC鋼より線20と、その表面に形成された熱硬化性樹脂の被覆層と、被覆層21から部分的に突出するように埋設された粒状体22とを具える被覆PC鋼より線である。 - 特許庁

If the respective wheels 16, 21 slip, the driving force transmitted to the rear wheel 21 side is increased as a second torque increase grade B which is smoother than a first torque increase grade A.例文帳に追加

また、各車輪16,21がスリップしている場合には、後輪21側に伝達する駆動力を第1のトルク増大勾配Aよりも緩やかな第2のトルク増大勾配Bにて増大させるようにした。 - 特許庁

This system is easy to fit the parking lock system even when the parking powl 86 and its supporting shaft 87 have to be inserted into the transmission case 21 together with the assembled body of the counter-shaft 75.例文帳に追加

パーキングポウル86およびその枢支軸87をカウンターシャフト75の組み立て体と共にセットで軸線方向へ変速機ケース21内に挿入しなければならない場合でも、パークロック装置の取り付けが容易である。 - 特許庁

The module 9 enciphers the identification information 19, etc., inputted by the user through the interface 11, prepares settlement request data 21 and transfers the data 21 to the terminal 1.例文帳に追加

決済モジュール9は、インターフェース11を介してユーザに入力された本人認証情報19等を暗号化して決済要求データ21を作成し、それを決済要求元端末1に渡す。 - 特許庁

A waveguide connection element 1 is configured to connect two waveguides 21, 22 and is equipped with: a connection element body 2; and a fixing member 6 for fixing the connection element body 2 to one waveguide 21.例文帳に追加

導波管接続素子1は、2つの導波管21、22を接続するものであり、接続素子本体2と、接続素子本体2を一方の導波管21に固定する固定部材6とを備える。 - 特許庁

A terminal 1 previously transmits display information such as title showing information to be provided to an information mediating terminal 21 and the information mediating terminal 21 discloses this information on the browser of a terminal 3.例文帳に追加

端末1が、提供しようとする情報を示すタイトルなどの表示情報を予め情報仲介端末21に送信し、情報仲介端末21は、これを端末3のブラウザ上で開示する。 - 特許庁

The cost calculation device 12 calculates wire lengths, the types and number of components, and processing work with the CAD model data 21, on the basis of the records and link information included in the CAD model data 21.例文帳に追加

コスト算出装置12は、CADモデルデータ21が、当該CADモデルデータ21に含まれるレコード及びリンク情報に基づいて、電線長、部品の種類及び個数、並びに加工作業を算出する。 - 特許庁

例文

The dividing walls 11 divide wedge-shaped, i.e., prism-shaped, partial spaces 20, 21 in the package, the partial spaces 20, 21 being disposed to accommodate felting needle bundles that are also wedge-shaped.例文帳に追加

隔壁11はパッケージ中に楔形の、即ちプリズム型の部分空間20,21を形成し、当該部分空間20,21は、同様に楔型をしたフェルト針の束を収納するよう配置される。 - 特許庁




  
Copyright © Japan Patent office. All Rights Reserved.
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する
英→日 日→英
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する

©2026 GRAS Group, Inc.RSS