Compressorを含む例文一覧と使い方
該当件数 : 22707件
In this compressor 1, rotation of the drive shaft S is converted into reciprocation of a piston 29 by a swash plate 26, and the delivery capacity of a refrigerant is changed by changing the inclination angle of the swash plate 26.例文帳に追加
圧縮機1は、駆動軸Sの回転を斜板26によってピストン29の往復動に変換すると共に、前記斜板26の傾斜角度を変更することにより冷媒の吐出容量を変更可能となっている。 - 特許庁
Thus the primary refrigerant compressed in single stage by the high-stage compressor 6, is circulated to the gas coolers 7, 8 for hot water supply and the gas cooler 9 for heating, and the circulation of primary refrigerant and the refrigerant temperature corresponding to the load can be achieved.例文帳に追加
それにより、高段圧縮機6が単段で圧縮した一次冷媒を給湯用ガスクーラ7,8と暖房用ガスクーラ9に循環させ、負荷に合わせた一次冷媒の循環量と冷媒温度を得る。 - 特許庁
When the outer air temperature is equal to or higher than a specified level, an expansion valve 3 is opened during the stopping period thus reducing the stopping and starting losses while avoiding overload of a compressor 2 at the time of restart.例文帳に追加
外気温度が所定の温度以上の場合は、停止期間中に膨張バルブ3を開くことにより、再始動時の圧縮機2の過負荷を回避しつつ停止と始動の損失を減少することができる。 - 特許庁
To provide a compressor capable of eliminating thermal influence exerted on a compression mechanism section due to a high pressure oil storage chamber, ensuring the volume of the high pressure oil storage chamber, and also preventing leakage of lubricating oil.例文帳に追加
圧縮機構部への高圧貯油室による熱の影響を排除すると共に、高圧貯油室の容積を確保することができ、かつ潤滑油の漏れを防止することができる圧縮機を提供する。 - 特許庁
To provide a capacity control mechanism capable of shortening a time taken until a discharge capacity is increased after the start of a variable displacement compressor and improving operation efficiency when operating by a minimum capacity.例文帳に追加
可変容量型圧縮機の起動後において吐出容量が大きくなるまでに掛かる時間を短縮でき、かつ最小容量運転時における運転効率を向上できる容量制御機構を提供する。 - 特許庁
The battery temperature T and the deterioration state of the second battery 28 and the operation state of a compressor 20, which is discriminated by an air conditioner operation state discriminating part 48 and is driven with the M/G 12 as a power source are detected.例文帳に追加
第2バッテリ28のバッテリ温度T及び劣化状態並びにエアコン作動状態判別部48により判別されるM/G12を動力源として駆動するコンプレッサ20の作動状態を検出する。 - 特許庁
(ii) For the gas holder for acetylene that is compressed by a compressor after fed from the generator, in addition to compliance with the provisions of the preceding item, to be equipped with a safety valve and a pressure gauge as prescribed in the following: 例文帳に追加
二 発生器から送り出された後、圧縮装置により圧縮されたアセチレンのためのガスだめにあつては、前号に定めるところによるほか、次に定める安全弁及び圧力計を備えていること。 - 日本法令外国語訳データベースシステム
To provide a hermetic compressor capable of reducing an oil discharge quantity to a sealed vessel external part, by cutting off an oil flow to the sealed vessel external part, in a flow process of oil sealed in a sealed vessel.例文帳に追加
密閉容器内に封入されているオイルの流動過程で、密閉容器外部へのオイル流動を遮断し、密閉容器外部へのオイル吐出量を低減することが出来る密閉型圧縮機を提供する。 - 特許庁
To provide a highly efficient motor assuring good productivity in the motor including a centralized winding which provides a direct winding to the teeth via an insulator, a method of manufacturing the same motor and a compressor using the same motor.例文帳に追加
ティースに絶縁物を介して直接巻線を施す集中巻の電動機において、高効率で、生産性の良好な電動機、およびその製造方法、ならびにそれを用いたコンプレッサーを提供する。 - 特許庁
To provide a hermetic compressor capable of suppressing noise emission by eliminating noises generated by self-exciting vibrations of a suction valve and a discharge valve and also collision generated when the suction valve and discharge valve are going to be closed.例文帳に追加
吸込み弁及び吐出弁の自励振動により発生する騒音と、吸込み弁及び吐出弁の閉鎖時に発生する衝突音をなくし騒音の低減を図れる密閉型圧縮機を提供する。 - 特許庁
In addition, the pressure loss of the header pipe 1b used as the refrigerant vapor exit can be reduced, so that the compressor entrance pressure of the heat pump is increased, and as a result, the coefficient of the performance of the heat pump is improved.例文帳に追加
さらに冷媒蒸気出口となる上ヘッダパイプ1bの圧力損失が低減できることになり、ヒートポンプの圧縮機入口圧力が上昇し、結果としてヒートポンプの成績係数を向上させるものである。 - 特許庁
To provide a compressor of a manual type and motor driven type which is capable of efficiently compressing materials to be compressed, eventually improves conveyance efficiency, is capable of easily compressing the materials by human hands or an electric motor and is excellent in workability.例文帳に追加
効率良く圧縮でき、その結果、搬送効率が向上すると共に、人の手又は電動モータで容易に圧縮でき、かつ作業性に優れた手動式及び電動式の圧縮装置を提供する。 - 特許庁
When the r.p.m. of the compressor 46 is low, delivery of refrigerant and condensation capacity are also low to cause no problem and the refrigerant flow is switched to channel (b), as shown on the drawing, by means of the second control valve 100.例文帳に追加
圧縮機46が低回転であれば冷媒吐出量も少なく凝縮能力も小さくて問題がないので、冷媒の流れを第2の制御弁100により図1のbの流路に切り替える。 - 特許庁
To provide a variable displacement compressor which can maintain excellent sealability, and can restrain an increase in manufacturing cost, by reducing a load applied to a casing, by making a response of delivery pressure excellent in restarting.例文帳に追加
再起動時の吐出圧のレスポンスを良好なものとすることが出来ると共に、筐体にかかる負荷を低減して、良好なシール性能を維持出来、製造コストの増大を抑制出来る可変容量コンプレッサを提供する。 - 特許庁
This heat pump device is constituted in such a way that a compressor 15, a heat exchanger 16 on use side, a pressure reduction mechanism 17, and a heat exchanger 18 on a heat source side are sequentially connected to operate a high pressure breaker when high pressure is abnormal.例文帳に追加
圧縮機15と、利用側熱交換器16と、減圧機構17と、熱源側熱交換器18とを順次接続し、高圧異常のときに高圧遮断器を作動させるヒートポンプ装置である。 - 特許庁
In the motor-driven compressor having a gas passage provided in a housing and allowing a gas to flow into a compression section, the drive circuit for driving the motor is installed in the housing and at least part of the drive circuit is disposed in the gas passage.例文帳に追加
ハウジング内にガスが圧縮部へと流れるガス通路を有する電動圧縮機において、電動モータを作動させる駆動回路をハウジングに内蔵し、駆動回路の少なくとも一部をガス通路に配設する。 - 特許庁
To provide an air conditioner in which a coolant and compressor oil, etc., do not remain in a radiation heat exchanger after stopping the inflow of the coolant to the radiation heat exchanger and a temperature of the radiation heat exchanger is easy to be lowered.例文帳に追加
輻射熱交換器への冷媒流入が止められた後でも、冷媒および圧縮機油などが輻射熱交換器に滞留せず、輻射熱交換器の温度が低下し易い空調機を提供する。 - 特許庁
A hole 44 which a droplet can pass through is formed on a guide wall 43 and a discharge passage 45 discharging droplet led to an outside of the guide wall 43 from the hole 44 to an outside of the compressor is provided on an outside of the guide wall 43.例文帳に追加
ガイド壁43には液滴の通過可能な孔44が形成され、ガイド壁43の外側には孔44からガイド壁43の外側に導かれた液滴を圧縮機の外部に排出する排出通路45が設けられている。 - 特許庁
To provide a swash plate compressor capable of realizing demonstration of an excellent sliding characteristic when a drive shaft is rotated at high speed, and of a high refrigerating capacity when the drive shaft is rotated at low speed.例文帳に追加
駆動軸が高速で回転される時における優れた摺動特性の発揮と、駆動軸が低速で回転される時における高い冷凍能力の発揮とを実現可能な斜板式圧縮機を提供する。 - 特許庁
To provide a scroll compressor in which sealability in a compression space is improved, by surely supplying oil to both compression spaces on the outer line side and the inner line side of a turning scroll.例文帳に追加
本発明が解決しようとする課題は、旋回スクロールの外線側と内線側の両方の圧縮室へ油を確実に供給し、圧縮室のシール性を向上させたスクロール圧縮機を提供することにある。 - 特許庁
A compressor displacement control operation circuit 35 is provided with a pilot valve 90 for a four-way selector valve including four connection fine pipes 93a-93d, a suction branch pipe 87, an intermediate pipe 88, a delivery branch pipe 89.例文帳に追加
圧縮機容量制御操作回路35は、4つの接続細管93a〜93dを有する四路切換弁用パイロット弁90と、吸入分岐管87と、中間管88と、吐出分岐管89とを備えている。 - 特許庁
A by-path route P through the pressure adjuster 7 is provided between the separation part K and the fuel return route R and a by-path route closing valve 23, a multi-winding capturing pipe 10 and a compressor 11 are provided thereon.例文帳に追加
前記隔離部分Kと前記燃料リターン経路R間に前記圧力調整器7をバイパスするバイパス経路Pを設け、これにバイパス経路開閉弁23と多重巻き捕集管10とコンプレッサ11を設ける。 - 特許庁
This scroll compressor 30 is constituted so that a positioning pin 112 having prescribed fitting accuracy is fitted, inserted, and fixed in a first hole part 110 by forming the first hole part 110 on an annular seat surface 32f of a front housing 32.例文帳に追加
スクロール型圧縮機30では、フロントハウジング32の環状座面32fに第1孔部110を形成し、この第1孔部110に所定の嵌め合い精度を有する位置決めピン112を嵌挿して固定する。 - 特許庁
In this method and compressor, a pallet-indexed image is re- indexed by using an array of a symbol cross count which displays the frequencies in occurrence of one or more determined context relations in the image, for example, one or more symbols adjacent to each other.例文帳に追加
1つ以上の所定のコンテクスト関係、例えば隣接した関係にあるシンボルの、画像内での発生頻度を表示するシンボルクロスカウントのアレイを使用し、パレットインデクシングされた画像を再インデクシングする。 - 特許庁
The compressor oil composition comprises a lubricating base oil having %C_A of 2 or less, a ratio of %C_P/%C_N of 6 or more and an iodine number of 2.5 or less, an antioxidant and an antimisting agent.例文帳に追加
本発明の圧縮機油組成物は、%C_Aが2以下、%C_P/%C_Nが6以上、ヨウ素価が2.5以下である潤滑油基油と、酸化防止剤と、ミスト防止剤とを含有することを特徴とする。 - 特許庁
In the open type compressor, valves 22, 23 are respectively disposed in an intake pipe 2 and a delivery pipe 3, and a service port 1 for recovering the refrigerant in a casing 11 is disposed on the casing 11.例文帳に追加
本発明の開放形圧縮機は、吸入管2と吐出管3との各々に弁22、23が設けられており、かつケーシング11内の冷媒を回収するためのサービスポート1が、ケーシング11に設けられている。 - 特許庁
To provide a variable displacement compressor with a bleed passage formed in a driving shaft with its inlet portion directly facing a crank chamber for communicating the crank chamber with a suction chamber, having desired discharge capacity during low load.例文帳に追加
クランク室と吸入室とを連通する抽気通路を、その入口部がクランク室に直接臨むように駆動軸内に設けた可変容量コンプレッサにおいて、低負荷時に所望の吐出容量が得られるようにする。 - 特許庁
The compressor 1 comprises a balance weight 54 correcting a rotational balance of the swirl scroll 4, and front case 6 having a supply passage 62 taking lubricating oil from the outside to the inside and housing the balance weight 54.例文帳に追加
そして、旋回スクロール4の回転バランスを補正するバランスウェイト54と、潤滑油を外部から内部に取り込むための供給路62を有すると共にバランスウェイト54を収容するフロントケース6とを含み構成される。 - 特許庁
To efficiently cool a heat radiating fin being a heat radiating part of an electric equipment part, without being influenced by heating from a condenser and a compressor, even when a heat exchanger acts as the condenser in cooling operation.例文帳に追加
冷房運転時など熱交換器が凝縮器として作用するときでも凝縮器や圧縮機からの発熱の影響を受けず、電装部品の放熱部である放熱フィンの冷却を効率良く行う。 - 特許庁
When the sealing cap 101 is inserted into the opening 1 of the compressor and the push-in pin 31 is pushed toward the opening 1, the push-in pin 31 presses the sealing part base 21 against the opening 1 radially outward.例文帳に追加
シールキャップ101が圧縮機の開口1に挿入され、押し込みピン31が開口1に向かって押圧されると、押し込みピン31は、開口1に対し、シール部ベース21を径方向外側に向かって押し付ける。 - 特許庁
A compressor 1 having a refrigerant sucking port 10 and a refrigerant discharging port 30 is provided with a motor 3 installed on the refrigerant sucking port 10 side, and a compressing element 5 installed on the refrigerant discharging port 30 side.例文帳に追加
冷媒吸入口10と冷媒吐出口30とを有する圧縮機1であって、冷媒吸入口10側に設置されたモータ3と、冷媒吐出口30側に設置された圧縮要素5とを備えている。 - 特許庁
The scroll compressor is provided with a fixed scroll including a scroll lap 31b, a revolving scroll including a scroll lap 32b meshing with the scroll lap 31b of the fixed scroll, and a motor driving the revolving scroll.例文帳に追加
渦巻き状のラップ31bを有する固定スクロールと、固定スクロールの渦巻き状のラップ31bと互いに噛合する渦巻き状のラップ32bを有する旋回スクロールと、旋回スクロールを駆動するモータとを備える。 - 特許庁
To provide a refrigerating machine, and a refrigerating and air-conditioning system including the same, capable of being properly operated even when a plurality of evaporators are connected to one compressor and one condenser.例文帳に追加
一つの圧縮機及び凝縮器に対して複数の蒸発器を接続した場合であっても良好に運転することができる冷凍機、及び、そのような冷凍機を備えた冷凍空調システムを提供する。 - 特許庁
The casing 13 is divided into an outdoor unit 11 which houses the compressor 1a and the outdoor heat-exchanger 2a, and an indoor unit 10 which houses the pressure reducing device 3a and the indoor heat-exchanger 4a by a bulkhead 12.例文帳に追加
筐体13は、隔壁12によって圧縮機1a、室外熱交換器2aを収納する室外ユニット11と減圧装置3a、室内熱交換器4aを収納する室内ユニット10とに区分されている。 - 特許庁
To provide a wet blasting device having a high-pressure cleaning function to make energy conservation possible without using a compressor and to enable a user to carry out blasting and cleaning work together as well.例文帳に追加
本発明はコンプレッサーを用いずに省エネルギー化でき、且つブラスト加工を行うと共に洗浄作業も一緒に行うことが可能である高圧洗浄機能を有した湿式ブラスト装置を提供することを目的とする。 - 特許庁
The casing 1 is formed in a state that its frame has a roughly-square cross section, the hot water storage tank 33 has a roughly-circular cross section, and the compressor 55 is disposed at a corner of the casing 1.例文帳に追加
ケーシング1は、その外郭が横断面概略四角形になるように形成され、また、貯湯タンク33は横断面概略円形になるように形成されており、圧縮機55は、ケーシング1のコーナー部に配置する。 - 特許庁
To provide a scroll compressor capable of accurately turning a rotation regulating pin of a movable scroll member along an inner peripheral surface of a circular hole, even if the movable scroll member is formed of an aluminum-based raw material.例文帳に追加
可動スクロール部材をアルミニウム系素材によって形成しても、可動スクロール部材の自転規制用のピンを円形孔の内周面に沿って精度よく旋回させることのできるスクロール型圧縮機を提供する。 - 特許庁
At least one jet pipe 33 for supplying a certain amount of compressor discharge air 64 into the burner body 16 is provided, and the jet pipe is arranged between an opening 34 and a casing 20.例文帳に追加
ある量の圧縮機吐出空気(64)を燃焼器本体(16)内に供給するための少なくとも1つの噴射管(33)が設けられ、噴射管は、開口部(34)とケーシング(20)との間に配置される。 - 特許庁
To provide a magnetizing method and device for a permanent magnet type motor, capable of magnetizing an unmagnetized magnetic member by accurately performing positional matching of a rotor with a stator with a small-sized device even if a compressor has a structure that its inside part is invisible.例文帳に追加
圧縮機内部が見えない構造でも、小型設備で正確に回転子を固定子に対して位置整合し、未着磁の磁性部材を着磁する永久磁石型電動機の着磁方法および装置を提供する。 - 特許庁
To minimize friction loss generated in a process of transmitting rotating power of an electric motor to a rotating scroll and wear of parts in a scroll compressor and to facilitate replacement of worn parts.例文帳に追加
スクロール圧縮機において駆動モータの回転力を旋回スクロールに伝達する過程で発生する摩擦損失及び部品の摩耗を最小化すると共に、摩耗した部品を容易に交換できるようにすること。 - 特許庁
An installing manager different from the user of the compressed air installs a compressed air supplying facility 1 including an air compressor 2, so as to supply the compressed air to a user piping 22 connected with air pressure equipments 23-25.例文帳に追加
圧縮空気の利用者と異なる設置運営者が空気圧縮機2を含む圧縮空気供給設備1を設置し、空圧機器23〜25が接続された利用者配管22に圧縮空気を供給する。 - 特許庁
This multistage compressor 12 comprises an inter-stage duct 45, in which a fluid flows, a liquid holder 70 arranged inside the inter-stage duct 45 so as to hold the liquid, and a liquid supply part 80 for supplying the liquid to the liquid holder 70.例文帳に追加
多段圧縮機(12)は、流体が流れる段間ダクト(45)と、段間ダクト(45)内に配置されかつ液体を保持する液保持体(70)と、液保持体(70)に液体を供給する液供給部(80)と、を備える。 - 特許庁
To improve comfortableness in an air conditioner comprising one outdoor unit and a plurality of indoor units connected thereto by sufficiently bringing out the heating capability of an operating-side indoor unit even at the time of low rotation of a compressor.例文帳に追加
1台の室外機と複数台の室内機を接続した空気調和機において、圧縮機の低回転時においても運転側の室内機の暖房能力を十分に引き出して快適性を向上させること。 - 特許庁
To provide a vehicular air conditioning system using refrigerant such as carbon dioxide for improving heating performance while reducing the power of a compressor with a reduction in loss due to the resistance of a passage in an internal heat exchanger.例文帳に追加
二酸化炭素などの冷媒を用いた車両用空調装置において、内部熱交換器における通路抵抗による損失を少なくして圧縮機の動力を低減するとともに、暖房性能を向上させる。 - 特許庁
This arrangement achieves the air-conditioning, heating and dehumidification heating modes by the simple configuration, without separately arranging a refrigerant flow path from a compressor 11 to an outdoor heat exchanger 20 according to the operation mode of an air conditioner.例文帳に追加
これにより、圧縮機11から室外熱交換器20に至る冷媒流路を、空調装置の運転モードに応じて別個に設けることなく、簡素な構成で冷房、暖房、および除湿暖房を実現する。 - 特許庁
On the side facing a bearing housing of the diffuser part 50d, a projected curved surface 50d formed into a circular-arc shape in cross section bent to the side of a scroll passage 52 of the compressor toward an outside diameter is formed along an outer periphery of the diffuser part 50d.例文帳に追加
デフューザ部50dのうち軸受ハウジングに面する側に、外径に向かうつれてコンプレッサのスクロール通路52側に曲がる断面円弧状の凸曲面50d´がデフューザ部外周に沿って形成されている。 - 特許庁
To provide a variable displacement compressor which makes a displacement changing control of high reliability without risk that any foreign matter stagnates in a passage provided for displacement control and simplifies the processing, in particular processing of a cylinder block.例文帳に追加
容量制御用に設けられた通路に異物が停滞せず信頼性の高い容量可変制御が可能で、かつ、加工、とくにシリンダブロックの加工の簡略化が可能な可変容量圧縮機を提供する。 - 特許庁
In a refrigerant circuit consisting of a water side heat exchanger 1, a compressor 2, an air side heat exchanger 3 and an expansion valve 4 connected together, the four-way selective valve 5 is provided for changing over the direction of circulating refrigerant in the refrigerant circuit.例文帳に追加
水側熱交換器1と、圧縮機2と、空気側熱交換器3と、膨張弁4とを接続してなる冷媒回路に、この冷媒回路の冷媒循環方向を切り換える四路切換弁5を備える。 - 特許庁
To enhance the efficiency of a scroll compressor by stabilizing the pressure of a back pressure chamber provided on the back surface of a scroll member to thereby reduce the fluctuation of a biasing force for biasing one scroll member to the other scroll member.例文帳に追加
スクロール部材の背面に設ける背圧室の圧力を安定化することで、一方のスクロール部材が他方のスクロール部材に付勢される付勢力の変動を低減してスクロール圧縮機の高効率化を図る。 - 特許庁
In the scroll compressor, communicating passages 24e, 24f, 24d, 24g, 34 extending from a plurality of middle compressing chambers 26A, 26B in the middle of compressing merge with each other in a midpoint (the chamber 24d) and reach a discharging port 20c.例文帳に追加
スクロール型圧縮機において、圧縮途中にある複数の中間圧縮室26A,26Bから延びる連通路(24e,24f,24d,24g,34)は、その途中(チャンバ24d)において合流して吐出ポート20cに到達されている。 - 特許庁
| ※この記事は「日本法令外国語訳データベースシステム」の2010年9月現在の情報を転載しております。 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|
