Compressorを含む例文一覧と使い方
該当件数 : 22706件
Particularly, when fining the operation spectrum of the internal combustion engine by a large number of the exhaust drive-type superchargers, there is employed a compact structural form of the exhaust drive-type supercharger, and in addition to this, there is employed, in particular, the compact auxiliary compressor.例文帳に追加
特に多数の排気駆動式過給機により内燃機関の運転スペクトルを細分する場合に、排気駆動式過給機の小形の構造形態のほかに、同時に特に小形の補助コンプレッサが実現される。 - 特許庁
To expand the control range of operation capacity by reducing the lower limit of the operation capacity while avoiding excessive temperature rise of a motor in a screw compressor in which a screw rotor (40) and the motor are housed in one casing.例文帳に追加
スクリューロータ(40)と電動機が一つのケーシングに収容されたスクリュー圧縮機において、電動機の過昇温を回避しつつ、その運転容量の下限を引き下げて運転容量の制御範囲を拡大する。 - 特許庁
According to this method, freezing in the cold water pour-out pipeline 31, which is started by pour-out operation on the half way of super- cooling operation, is prevented and icing on an evaporator 13 is quickened by the continuation of operation of the compressor 17.例文帳に追加
これにより、過冷却運転途上での注出動作をきっかけとする冷水注出管路内31での凍結を防止し、かつ圧縮機17の運転継続で蒸発器13への着氷を早める。 - 特許庁
When reheating the bathtub water while heating the supply hot eater, the passage is switched to sequentially circulate the refrigerant through the compressor 11, the exchanger 12, the exchanger 16 and the unit 14.例文帳に追加
また、給湯水を加熱しながら風呂の湯を追焚する場合には、冷媒を圧縮機11、給湯側熱交換器12、風呂側熱交換器16、第1減圧器14を順次循環するように冷媒循環路を切替える。 - 特許庁
This water lubricated type screw compressor is provided with a pair of a male screw rotor 1 and a female screw rotor 2, casings 3, 4, and 5 for storing the rotors, and bearings 6-9 retained to the casings and supporting the pair of rotors.例文帳に追加
水潤滑式スクリュー圧縮機は、1対の雄スクリューロータ1と雌スクリューロータ2と、これらロータを収容するケーシング3、4、5と、このケーシングに保持され1対のロータを支承する軸受6〜9とを有している。 - 特許庁
In one embodiment, the component is not exchanged, but in order to achieve the target acceleration, (1) the scheduled fuel flow rate is increased, and (2) the stall margin of a compressor is increased.例文帳に追加
本発明の1つの形態において、構成部品は交換されるのではなく、目標加速度を達成するために、(1)スケジューリングされた燃料流量が増加され、更に(2)圧縮機失速マージンが増大される。 - 特許庁
To prevent a refrigerant to have abnormally high pressure even when a pressure of the refrigerant is suddenly increased by being compressed by a compressor, in a solenoid control valve used as a pressure reducer of a refrigerating cycle.例文帳に追加
冷凍サイクルの減圧装置として使用される電磁制御弁において、圧縮機によって冷媒が圧縮されることによりその冷媒の圧力が急上昇しても異常高圧にはならないようにする。 - 特許庁
To provide a compressor capable of reducing pressure loss at a suction valve part in suction stroke, improving suction efficiency and the like, and inhibiting vibration of a suction reed valve by reduction of pressure loss.例文帳に追加
吸入行程における吸入弁部の圧力損失を低減し、吸入効率等を向上させるとともに、圧力損失低減により吸入リード弁の振動発生を抑制可能な圧縮機を提供する。 - 特許庁
To provide a scroll compressor capable of preventing damage to a bearing and the like by employing a structure minimizing a thrust slide loss and surely pumping oil in an oil reservoir even in any operation state.例文帳に追加
いかなる運転状態においてもスラスト摺動損失を最も小さくでき、かつ油溜まりの油を確実に吸い上げられる構造とし、軸受部分等の損傷を防ぐことができるスクロール圧縮機を提供する。 - 特許庁
To provide a hermetic compressor capable of reducing an oil circulation ratio and excluding affects to motor performance while securing an oil returning property of lubrication oil by diametrically increasing an oil returning pipe.例文帳に追加
油循環率を低減することができるとともに、返油パイプを大径化して潤滑油の返油性を確保しながら、モータ性能への影響を排除することができる密閉型圧縮機を提供することを目的とする。 - 特許庁
In the air-conditioning system 1, a multi-vane type (or scroll type) compressor 2, an indoor equipment heat exchanger 11, an outdoor equipment heat exchanger 12, and an intermediate pressure heat exchanger 13 are connected by refrigerant piping 3.例文帳に追加
冷暖房システム1は,マルチベーン式(またはスクロール式)の圧縮機2と室内機熱交換器11と室外機熱交換器12と中間圧熱交換器13とが冷媒配管3によって接続されている。 - 特許庁
At the time of stopping, outside air compressed by a compressor 25 is supplied to a fuel chamber in a fuel cell stack 100, and is substituted with oxidant gas, therefore, a period of time for substituting with air in the fuel chamber can be shortened.例文帳に追加
停止時には、コンプレッサ25で圧縮された外気を、燃料電池スタック100内の燃料室に供給し、酸化ガスと置換しているので、燃料室内を空気に置換する時間を短縮することができる。 - 特許庁
To provide a compressor reducing resistance of delivery gas flowing from a delivery valve toward a delivery chamber and reducing power loss by securing flow pass of the delivery gas flowing from the delivery valve toward the delivery chamber.例文帳に追加
吐出弁から吐出室へ向かう吐出ガスの流路を確保することにより、吐出弁から吐出室へ向かう吐出ガスの抜けを改善し、動力ロスを低減することが可能な圧縮機を提供する。 - 特許庁
A high-pressure pressure switch 70 detects this case from the fact that a high-pressure-side pressure of a compressor 52 exceeds a set value, and the drain water collected in the drain pan 74 is sent out to the condenser 54 side by a drain pump 82.例文帳に追加
この場合を、高圧圧力スイッチ70が圧縮機52の高圧側圧力が設定値を越えたことに基づいて検知し、受水皿74に溜まったドレン水をドレンポンプ82で凝縮器54側に送出する。 - 特許庁
When the indoor temperature is lowered when the operation of the compressor is started, the sensor senses the lower limit temperature and the cooler is stopped, and then the indoor temperature does not overshoot, the upper and lower limit temperatures are reset to the initial states.例文帳に追加
圧縮機の運転開始に伴って庫内温度が低下し、センサーが下限温度を検知し冷却装置を停止させた後、庫内温度がオーバーシュートしなくなったら、上下限温度を初期状態に復帰させる。 - 特許庁
The heat-source-side main refrigerant circuit 20 includes a compressor 21, a heat-source-side heat exchanger 25, a receiver 127 capable of storing a coolant, and a heat-source-side main refrigerant pipe 30 for connecting the apparatuses.例文帳に追加
熱源側主冷媒回路20は、圧縮機21と、熱源側熱交換器25と、冷媒を溜めることが可能なレシーバ127と、これらの機器を接続するための熱源側主冷媒配管30とを含んでいる。 - 特許庁
A first refrigerant circuit 10 includes a compressor 11, an outside air-side heat exchanger 14, an expansion valve 12, a heat exchanging region 16, a cold water heater 15, and connecting state setting sections 17-19 setting connecting states thereof.例文帳に追加
第1冷媒回路10は、圧縮機11、外気側熱交換器14、膨張弁12、熱交換部位16、冷温水器15、これらの接続状態を設定する接続状態設定部17〜19を備える。 - 特許庁
In a first step S14, a present converted high-pressure value of the refrigerant in a high-pressure piping of a compressor is obtained by converting a present detected temperature detected by an outdoor heat exchanger temperature sensor mounted on the outdoor heat exchanger.例文帳に追加
ステップS14では、室外熱交換器に取り付けられた室外熱交温度センサの現在の検知温度から換算して圧縮機の高圧側配管内の冷媒の現在の換算高圧値が得られる。 - 特許庁
Thus, even if a normal main shaft end plate and an auxiliary shaft end plate are fastened again with a bolt, the strain of the end surface is restrained, and the highly reliably hermetic rotary compressor can be provided.例文帳に追加
これによって、再度、正規の主軸端板および補助軸端板をボルトにて締結しても、端面の歪みを抑制し、信頼性の高い密閉型回転式圧縮機を提供することができるものである。 - 特許庁
To provide an air conditioner capable of solving a situation where oil returning operation cannot be achieved for a long time due to abnormally high outside temperature and of preventing damage caused by shortage of lubricating oil of a compressor.例文帳に追加
異常な高外気温による油戻し運転の長時間に亘る不成立を解消し、圧縮機の潤滑油切れによる損傷を防止することができる空気調和機を提供することを目的とする。 - 特許庁
The reciprocating compressor includes the gasket (28) which is interposed between a cylinder block and a cylinder head and has a seal section (28b) formed with a communication hole (28a) communicating with a cylinder bore (26) and formed with a lightening hole (28c) by cutting the wall at a predetermined position.例文帳に追加
シリンダブロックとシリンダヘッドとの間に介装され、シリンダボア(26)と連通する連通孔(28a)が形成されるとともに、所定箇所を肉抜きして肉抜き孔(28c)が形成されたシール部(28b)を有するガスケット(28)とを備える。 - 特許庁
The guide part can thus be composed without increasing the number of parts, and the hinge part 12 can be composed in a simple structure, and thereby the guide part can be composed while reducing manufacturing cost of a compressor.例文帳に追加
これにより、部品点数を増加させることなくガイド部を構成することができるとともに、簡素な構造でヒンジ部を構成できるので、圧縮機の製造原価低減を図りつつ、ガイド部を構成することができる。 - 特許庁
This constitution sets a compression ratio to 2.9 and prevents the lowering of compression efficiency while contriving the versatility of a part even in the case of a scroll compressor using a so-called new refrigerant, such as R-410A.例文帳に追加
これにより、圧縮比が2.9になるようにして、R−410A等のいやゆる新冷媒を用いたスクロール圧縮機でも部品の汎用性を図りながら圧縮効率の低下が起らないようにする。 - 特許庁
Accordingly, the affection to the outlet temperature of the indoor machine under the heating operation of another room can be reduced by controlling the compressor and the expansion valve whereby continuous operation can be effected with a capacity same as a designed value.例文帳に追加
従って、圧縮機や膨張弁を制御することにより他室で暖房運転している室内機の吹き出し温度への影響を少なくすることができ、設計値通りの能力で連続運転が可能になる。 - 特許庁
This air conditioner has a DC voltage detecting means, and is constituted so that the whole upper-lower arms become an OFF state when a compressor stops since DC voltage becomes a prescribed value or more by a regenerative current by the following wind.例文帳に追加
直流電圧検出手段を有し、順風による回生電流によって直流電圧が所定の値以上になり、且つ圧縮機が停止している場合に、上下アームを全てオフ状態にする。 - 特許庁
A refrigerating device is provided with a low stage side refrigerant circuit 2 constituted of a compressor 4, a cascade condenser 5, a low stage side receiver 6, a low stage side expansion valve 7 consisting of a temperature sensitive type expansion valve, and an evaporator 8, which are connected sequentially.例文帳に追加
低段側圧縮機(4)、カスケードコンデンサ(5)、低段側レシーバ(6)、感温式膨張弁から成る低段側膨張弁(7)、及び蒸発器(8)を順に接続して構成された低段側冷媒回路(2)を備える。 - 特許庁
A pressure sensor 98, in addition to LEDs 88_1-88_8 ((1)-(8)), the motor 68, a power supply ON switch 90, a power supply OFF switch 92, and a silence mode switch 93, is connected to the control section 94 of the air compressor 10.例文帳に追加
空気圧縮機10の制御部94には、上記LED88_1〜88_8((1)〜(8))、モータ68、電源ONスイッチ90、電源OFFスイッチ92、静音モードスイッチ93の他に圧力センサ98とが接続されている。 - 特許庁
LEDs 88_1-88_8 ((1) to (8)), a motor 68, a power source ON-switch 90, a power source OFF-switch 92, a silence mode switch 93, and a pressure sensor 98 are connected to a control section 94 of the air compressor 10.例文帳に追加
空気圧縮機10の制御部94には、上記LED88_1〜88_8(▲1▼〜▲8▼)、モータ68、電源ONスイッチ90、電源OFFスイッチ92、静音モードスイッチ93の他に圧力センサ98とが接続されている。 - 特許庁
When the r.p.m. of the compressor 46 is high, the refrigerant flow is switched to channel (a), as shown on the drawing, by means of the second control valve 100 and refrigerant is fed entirely to the condenser 62 thus preventing the condensing temperature from increasing.例文帳に追加
圧縮機46が高回転であれば第2の制御弁100により冷媒を図1のaの流路に切り替え、凝縮器62全てに冷媒を流し、凝縮温度を高くさせないようにしている。 - 特許庁
A stationary core 13, a rotor 15 fixed to a main shaft 5, and a main bearing 6 and a sub-bearing 7 to support the main shaft rotatably are shrink-fitted to a cylindrical trunk 11, and then a compressor 20 is assembled.例文帳に追加
円筒胴部11内に固定鉄心13、主軸5に固定された回転子15、主軸を回転自在に支持する主軸受け部6及び副軸受け部7を焼き嵌めにて装着後、圧縮機部20を組み込む。 - 特許庁
To hold the withstand pressure of a sealed casing and to avoid the risk of breakage of a terminal part in a compressor comprising a terminal provided on the end cap of the sealed casing by abolishing the welding of the terminal part to prevent cracking.例文帳に追加
密閉容器のエンドキャップにターミナルが設けられた圧縮機であって、ターミナル部の溶接を廃止してクラックの発生を防止し、密閉容器の耐圧を保持すると共にターミナル部の破壊の危険性を回避する。 - 特許庁
The pulse pipe refrigerating machine comprises a compressor 1, a cold storage device 2, a pulse pipe 3 and a buffer 4 which are connected with each other in series, and is further provided with a cooling head 5 connecting the low temperature end 2a of the cold storage device and the low temperature end 3a of the pulse pipe.例文帳に追加
圧縮機1と、蓄冷器2と、パルス管3と、バッファ4とを直列に接続してなり、上記蓄冷器の低温端2aと、パルス管の低温端3aとを連結する冷却ヘッド5を備える。 - 特許庁
A multi-variable controller (41) includes a dynamic model of a refrigerant circuit (12) in which both a capacity of the compressor and a degree of opening of an outdoor expansion valve are applied as its control input and both a condensing temperature and the over-heating degree are applied as its control output.例文帳に追加
多変数制御器(41)は、圧縮機の容量と室外膨張弁の開度とを制御入力とし、且つ凝縮温度と過熱度とを制御出力とする冷媒回路(12)の動的モデルを備えている。 - 特許庁
This compressor has a separation chamber 11 formed into the shape of an approximately cylindrical hole, the open end of the separation chamber 11 being formed as a connection to a delivery pipeline 20, with a separation pipe 12a fitted inward of the connection of the separation chamber 11.例文帳に追加
略円柱穴形状に形成された分離室11を有し、分離室11の開口端側を吐出配管20との接続部とし、分離室11の接続部より内部に、分離管12aを嵌挿した。 - 特許庁
To provide a compressor enabling sure attachment of a stator core to a hermetic vessel while preventing deformation of the stator core due to attachment to the hermetic vessel, improving motor efficiency and reducing noise and vibration.例文帳に追加
ステータコアの密閉容器への取付変形を防止しつつステータコアを密閉容器に確実に取り付けることができて、モータ効率を向上すると共に騒音や振動を低減した圧縮機を提供する。 - 特許庁
The tip of the plate spring material is lifted against spring resiliency in the thickness direction, the tip of an arm part 52 of the bearing member 50 is locked in the recessed parts 64, and the connection of the pulley 43 to the compressor is secured.例文帳に追加
板バネ材の先端部はその厚み方向のバネ弾性に抗して持ち上げられ、凹部64内に受承部材50の腕部52の先端を係入してプーリ43と圧縮機との作動連結を確保している。 - 特許庁
A valve housing 31 is joined at its one end with the ball valve element 37 and a discharge pressure introduction hollow pipe body 49 is provided to directly exert the discharge pressure of the compressor in the opening direction of the ball valve element 37.例文帳に追加
弁ハウジング31には一端にてボール弁体37と接合され、圧縮機の吐出圧力をボール弁体37の開弁方向へ直接及ぼす吐出圧力導入中空管体49を設ける。 - 特許庁
In the bush 52 which configures the scroll-type compressor 10, a groove part 80 is formed in a hole part 72 through which the crankpin 70 that eccentrically revolves around a rotation shaft 56 is inserted, to correspond to a rotation shaft axial line (L) side.例文帳に追加
スクロール型圧縮機10を構成するブッシュ52には、回転シャフト56に対し偏心して旋回するクランクピン70が挿通される孔部72に、回転シャフト軸線(L)側に対応して溝部80が形成される。 - 特許庁
Therefore, even in the case of a vehicle which drives an only comparatively short distance, the lubricant oil collecting in under-floor low pressure piping 28 and the like can be pushed back to the suction port 15b of the compressor 15.例文帳に追加
このため、比較的短い距離しか運転を行わない車両の場合であっても、床下低圧配管28等に溜まっている潤滑オイルを圧縮機15の吸入口15b側に押し戻すことができる。 - 特許庁
The method and device for monitoring the air mass flow measuring device 1 in the air supply system of the internal combustion engine 5 provided with the electric compressor 10 allows a precise modeling of the air mass flow.例文帳に追加
空気質量流量の正確なモデル化を可能にする、電動圧縮機(10)を備えた内燃機関(5)の給気系内の空気質量流量測定装置(1)のモニタ方法および装置が提案される。 - 特許庁
A coating (6) of a comparatively soft metal is applied by electrical discharge surface treatment at a part (5) undergoing a specific pressure from a disc (7) in an implantation part (4) of the blade (1) to be implanted in a disc (7) of the compressor of the gas turbine.例文帳に追加
ガスタービンエンジンの圧縮機のディスク(7)に植込まれる翼(1)の植込み部(4)において、ディスク(7)から面圧を受ける部分(5)に、放電表面処理を用いて比較的軟らかい金属をコーティング(6)する。 - 特許庁
To provide a compressor which enables the saving of man-hours for mounting a heat source member and a reduction in cost since a dedicated heat source member for heating lubricating oil does not need to be installed separately.例文帳に追加
潤滑油を加熱するための専用の熱源部材を別途設置する必要がなく、熱源部材の取付工数を省くことができると共に、コストの低減を図ることができる圧縮機を提供する。 - 特許庁
By this, loads acting on the support leg 5 are constantly equal, and even when the support legs 5 wear out due to secular change, the compressor does not slant since the support legs wear out equally.例文帳に追加
これにより、おのおのの支持脚5に作用する荷重は、常に均等となり、例え支持脚5が経年変化によりへたるようなことがあった場合でも、均等にへたるので、圧縮機が傾くようなことはない。 - 特許庁
When the direction control valve 32 is switched to a switching position 3, the exhaust air inside the air tank 30 is sucked into a compression chamber of the scroll compressor 1 from a re-compression pipe 31 under the pre-compression condition.例文帳に追加
そして、方向制御弁32を切換位置(ハ)に切換えたときには、空気タンク30内の排気空気を再圧縮管路31から予圧縮状態でスクロール式圧縮機1の圧縮室内に吸込ませる。 - 特許庁
To provide a heat pump using a positive-displacement compressor and its operation method, capable of taking out warm water of comparatively high temperature of 55-70°C while suppressing overheating of a discharge temperature and a driving motor, and further power-up.例文帳に追加
吐出温度と駆動モータの過熱、更には動力アップを抑制しつつ、55〜70℃といった比較的高温の温水が取出し可能な、容積式圧縮機を用いたヒートポンプ及びその運転方法を提供すること。 - 特許庁
To compress gas by securing a clearance structure for extremely reducing a backflow of the gas on the suction side and the delivery side, while removing the heat of a rotor and a casing of a root type compressor of storing a plurality of stage numbers in an integral casing.例文帳に追加
複数の段数を一体のケーシングに収めるルーツ式コンプレッサーのロータ及びケーシングの除熱と、吸入側と吐出側のガスの逆流を極度に小さくする隙間構造を確保してガスを圧縮する。 - 特許庁
A toilet device includes a control unit which is structured to change an operating condition of a crushing mechanism, an air compressor and the like based on an operation mode selected from a plurality of operation modes (for example, normal mode and silent mode).例文帳に追加
複数の動作モード(例えば、通常モード及び静音モード)の中から選択された当該動作モードに基づいて、粉砕機構部やエアーコンプレッサー等の動作条件を変更する制御ユニットを備える。 - 特許庁
A compressed low-pitch signal S105 and a middle-pitch/high-pitch signal S104 are composited by a composition unit 104, further, the dynamic range of a composite signal is then compressed by a composite signal compressor unit 106, and the compressed signal is amplified by an amplifier unit 107 thereafter.例文帳に追加
合成部104で圧縮低域信号S105と中高域信号S104を合成した後、さらに合成信号コンプレッサ部106でダイナミックレンジを圧縮し、その後アンプ部107で増幅する。 - 特許庁
To provide a compressor device consisting of a small number of constituent parts, using two compressors, capable of making use of the calculators installed on the respective compressors, and making uniform the maintenance apparatus.例文帳に追加
構成品の数が少なく、2台の圧縮機のそれぞれに個別に設けられている演算器を有効活用することができ、しかもメインテナンス機関の均一化を可能ならしめる圧縮機装置を提供する。 - 特許庁
To provide an image compressor and expander which can minimize the influences of distortion when an image corresponding to a combination of a fixed background image and a given information image is input to be coded.例文帳に追加
定型の背景画像に任意の情報画像が結合された画像を符号化するにあたり,画像取り込み時の歪みの影響を最小限とすることの可能な画像圧縮装置及び画像伸張装置を提供する。 - 特許庁
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|