| 意味 | 例文 |
Load currentの部分一致の例文一覧と使い方
該当件数 : 4257件
A detection signal is extracted by smoothing change of a load current with an integral means 77, and a duty ratio of voltage applied to the driving means 72 is varied corresponding to a result of comparison with a comparison signal.例文帳に追加
負荷電流の変化を積分手段77で平滑して検知信号を取り出し、比較信号とその大きさを比べて大小関係に対応して駆動手段72に印加される電圧のデューティ比を変化させる。 - 特許庁
When the large current runs through at the start up of an engine cell motor of a battery load, a battery voltage significantly falls, and a third switching element 12 is conducted by a signal from a second comparative circuit 11 for energizing a second electromagnetic relay 13.例文帳に追加
バッテリ負荷のエンジンセルモ−タ始動時に大電流が流れると、バッテリ電圧が大幅に低下して第2の比較回路11からの信号で第3スイッチ素子12が導通し、第2電磁リレ−13が付勢される。 - 特許庁
To solve the problem of securing a load factor by an inrush current at start, output fluctuations due to seasons, and the maintenance of battery charging charges, and so on, when a small-scale distributed power source is used as an independent power source.例文帳に追加
小規模分散型電源を自立電源として用いると、起動時の突入電流による負荷率の確保、季節による出力変動、バッテリーの充電電荷の維持等において課題を有している。 - 特許庁
The consumption of power in a conventional scheme wherein a maximum load current is caused to flow to the detection circuit in a spurious manner just for the detection, is eliminated and detection error caused by the overlap of the transmitting operation and the detecting operation can also be prevented.例文帳に追加
検出だけのために擬似的に最大負荷電流を検出回路に流す従来方式による電力の消費を無くし、送信動作と検出動作が重なることによる検出エラーも防げる。 - 特許庁
This voltage control method for a self-excitation induction generator changes an inductance by a variable reactor to change a value of an equivalent capacitive current so as to correspond to a revolution of the self-excitation induction generator and a load variation.例文帳に追加
自励式誘導発電機の電圧制御方法であって、可変リアクトルによってインダクタンスを変化させて等価進相電流の大きさを自励式誘導発電機の回転数と負荷変化に対応して変化させる。 - 特許庁
To provide a fuel cell device in which effect of impurity gas accumulated in a fuel supply space can be reduced even in a usage to repeat outputting and stopping and a usage with a small output current and a large load fluctuation.例文帳に追加
出力と停止とを繰り返す用途、小さな出力電流、負荷変動の大きな用途においても、燃料供給空間に蓄積した不純物ガスの影響を軽減できる燃料電池装置を提供する。 - 特許庁
Control states for indicating current load situation of first to Nth (N≥2) controlled areas are collected and displayed on a display so that the collected control states of respective controlled areas are visually separated in terms of category.例文帳に追加
第1〜第N(N≧2)の被制御エリアの現在の負荷状況を示す制御ステータスを収集し、この収集した制御ステータスを被制御エリア毎に、その種別を視覚的に区分して、ディスプレイ上に表示する。 - 特許庁
To solve a problem such that the mean square of current command values which is used as one of oscillation detection methods in conventional technology is greatly changed in accordance with the characteristics of a load driven by a servo motor.例文帳に追加
従来技術では、発振検出の1つに電流指令値の2乗平均値を用いているが、電流指令値の2乗平均値は、サーボモータによって駆動される負荷の特性によって大きく変わる。 - 特許庁
Consequently, the rectifying element 6 prevents to flow the reverse current in the main contact 3, and to do harm to a DC load L and the like connected to other branching circuits before something happens.例文帳に追加
而して、主接点3に逆向きの電流が流れることを整流素子6で防止することができ、他の分岐回路に接続された直流負荷Lなどに悪影響が及ぶのを未然に防ぐことができる。 - 特許庁
To obtain a power circuit controlling the build-up rate of a voltage applied to a load and being capable of avoiding an unstable operation resulting from an inrush current at a mechanical contact interposed to a power feeder line.例文帳に追加
負荷へ印加する電圧の上昇率を制御し、電力供給線に介在する機械的接点における、突入電流に起因する不安定動作を回避することができる電源回路を得ることができる。 - 特許庁
A high internal resistance pentobe is used for a drive stage (V3 and V4), and the internal resistance of the drive stage is higher than the load resistances (R5 and R6) so that it is neglectable by applying current feedback at (R3 and R4).例文帳に追加
ドライブ段(V3,V4)は高内部抵抗五極管を使用し、(R3,R4)にて電流帰還をかけることにより、その内部抵抗を負荷抵抗(R5,R6)に比べ無視出来るぐらい高くしておく。 - 特許庁
When charging batteries V_0p and V_0n are charged with regenerative current from an outside load connected to three-phase AC terminals A, B and C, e.g. a three-phase induction motor, the switch elements Q_0p and Q_0n are turned on.例文帳に追加
スイッチ素子Q_0p及びQ_0nは、3相交流端子A、B及びCに接続された外部負荷である例えば3相誘導モータからの回生電流を充電池V_0p及びV_0nに充電する際にはオンする。 - 特許庁
To provide a generating function attached power supply device in a water supply device capable of driving also equipment having large load required high current and high power without hindrance in the power supply device of the water supply device equipped with a storage element and a generator supplying a power source.例文帳に追加
蓄電素子とこれに電源補給する発電機とを備えた給水装置の給電装置において、大電流,大電力を要する負荷の大きな機器をも支障なく駆動できるようにする。 - 特許庁
The backup power source has a bidirectional DC-to-DC converter 5 and a secondary battery 4 on the DC output side of the AC-to-DC converter 3, and causes the secondary battery 4 to flow a discharging current of a specified peak-cut level or higher to flow, when the load is at a peak.例文帳に追加
AC−DCコンバータ3の直流出力側に双方向DC−DCコンバータ5と二次電池4を持ち、ピーク負荷時に所定のピークカットレベル以上の電流を二次電池4から放電させる。 - 特許庁
Since the source follower circuit 102 is a high impedance input, even if a small source follower load resistance is used, the flowing current to an input terminal 111 can be reduced, and a small chip area can be realized.例文帳に追加
ソースフォロア回路102は、ハイインピーダンス入力であるため、小さなソースフォロア負荷抵抗を用いても入力端子111への流入電流を小さくすることができ、かつ小さなチップ面積を実現できる。 - 特許庁
A constant current source 9 is added to a resistance coupling amplifier circuit consisting of resistors R1, R2, a capacitor 4 and an operational amplifier 7 whose noninverting input is connected to one terminal of a load resistor 2 connected in series with a light receiving element 1.例文帳に追加
受光素子1に直列に接続した負荷抵抗2の一端を正入力とし,オペアンプ7と抵抗R1,R2,容量4で構成した抵抗結合増幅回路に,定電流源9を追加した。 - 特許庁
To reduce the magnitude of power harmonics generated in phase control to a limit value which is determined to the limit value-harmonic current generation limiting value of JIS C 6100-3-2, and moreover to enable control of a large load.例文帳に追加
位相制御において発生する電源高調波の大きさをJIS C6100−3−2の限度値—高調波電流発生限度値に定める限度値以下に低減させ、且つ大きな負荷の制御を可能とする - 特許庁
To prevent a large current from flowing owing to variance of a process, etc., by controlling the operations of a P-channel transistor and an N- channel transistor of the output stage in a power circuit which drives a load on a push-pull basis.例文帳に追加
プッシュプル方式により負荷を駆動する電源回路において、出力段のPチャネルトランジスタとNチャネルトランジスタの動作を制御することによって、プロセス等のばらつきにより大電流が流れることを防止する。 - 特許庁
The plurality of electric power receiving coils on the stage are arranged with their phase lag to the electric power transmission coil, and the frequency of the alternating-current magnetic field is set to the resonance frequency determined by a mutual inductance and a load between the electric power transmission coil and the electric power receiving coil.例文帳に追加
ステージ上の受電コイルは、送電コイルと位相をずらして複数個配置し、交流磁界の周波数を、送電コイルと受電コイル間の相互インダクタンスと負荷とで決まる共振周波数に設定する。 - 特許庁
To provide an insulated gate type semiconductor element which has a large load short circuiting resistance and in which current is concentrated at a part of a portion to be conducted to hardly generate a flowing state, and to provide a method for manufacturing the same.例文帳に追加
負荷短絡耐量が大きく、また導通すべき部分の一部に電流が集中して流れる状態が生じにくい絶縁ゲート型半導体素子やその製造方法を提供することである。 - 特許庁
To provide a gas-insulated on-load tap changer which can be made compact, can suppress temperature rise of a current limit element even when insulating gas with low heat capacity is used, and can provide a good maintenance workability.例文帳に追加
熱容量の低い絶縁ガスを使用する場合でも電流制限要素の温度上昇抑止および小型化を図り、しかも良好なメンテナンス作業性を獲得できるガス絶縁負荷時タップ切換器を提供する。 - 特許庁
When the infrared incident quantity is not changed continuously for a predetermined time, the absence of the user is determined, and the current-carrying to the electric heater 5, a blower 4, and the like on a load side to stop the heating.例文帳に追加
そして、赤外線入射量が連続して所定時間変化しない場合には使用者が不在であると判断して、負荷側の電気ヒータ5及び送風機4等への通電を遮断して暖房を停止する。 - 特許庁
When a load 24 is large, a transistor Q22 is externally attached to an IC 22, and an incorporated transistor Q21 and the externally attached transistor Q22 are simultaneously operated so that the current output capability of a linear regulator 21 can be increased.例文帳に追加
負荷24が大きい場合には、IC22にトランジスタQ22を外付けし、内蔵されたトランジスタQ21と外付けされたトランジスタQ22とを同時に動作させてリニアレギュレータ21の電流出力能力を高める。 - 特許庁
A DC input power supply voltage Vcc is outputted to a load side via a PNP transistor Q having a small Vce, a base thereof is driven by a base current, in which noises are removed by a power supply noise removing circuit 33.例文帳に追加
直流入力電源電圧VccをVceが小さいPNPトランジスタQを介して負荷側へ出力し、そのベースを電源ノイズ除去回路33でノイズ除去されたベース電流で駆動する。 - 特許庁
A switch adjuster makes a pulse-width modulation oscillator inactive by means of a fixed minimum non-zero duty cycle oscillator and provides a minimum ON-cycle to a power source switch in a switch oscillator, when a load current is low.例文帳に追加
負荷電流が低い場合、切り換え調整器は、固定最小非ゼロデューティサイクル発振器を用いてパルス幅変調発振器を無効にし、切り換え発振器における電源スイッチに最小ONサイクルを提供する。 - 特許庁
The overheat protective function semiconductor switch comprises a power element 1 provided in the main circuit passing a load current, and an overheat protection circuit 2 for interrupting the power element 1 when heat generation thereof exceeds an allowable range.例文帳に追加
負荷電流の流れる主回路に設けられたパワー素子1と、パワー素子1の発熱量が許容範囲を超えたときにパワー素子1を遮断する過熱保護回路2とを備えた過熱保護機能半導体スイッチ。 - 特許庁
This crystal oscillation circuit 30 is provided with a frequency temperature compensating circuit 12, a crystal vibrator 14, transistors TR1, TR2, a negative resistor R5, an output load capacitor C5, and a constant current source 22 or the like.例文帳に追加
水晶発振回路30は、周波数温度補償回路12と、水晶振動子14と、トランジスタTr1、Tr2と、負性抵抗R5と、出力負荷容量C5と、定電流源22等を備えている。 - 特許庁
Abnormal operation where a current flows through a switching element at a time before ending the off interval thereof is eliminated in case of middle load by setting the coupling coefficient k of a power isolation transformer PIT at about k=0.7 or less.例文帳に追加
絶縁コンバータトランスPITの結合係数k=0.7程度以下として、中間負荷時において、スイッチング素子のオフ期間が終了する以前のタイミングでスイッチング素子に電流が流れる異常動作を解消する。 - 特許庁
To provide a fuel cell system capable of effectively exhausting the gas inside the storage box without deteriorating the generation efficiency of the load current and enabled to be structured in light weight, compact at low cost.例文帳に追加
負荷電流の生成効率を低下させることなく、収納ボックス内のガスを効果的に排出することができるとともに、軽量、小型且つ安価に構成することのできる燃料電池システムを提供する。 - 特許庁
To provide a method of determining a design value of a crystal oscillation circuit by making clear a relationship of a load capacitance CL value, a negative resistance RL value and a drive current Ios value of the oscillation circuit employing a crystal oscillator.例文帳に追加
水晶振動子を用いた発振回路の負荷容量CL値、負性抵抗RL値、および駆動電流Ios値の関係を明確にし、水晶発振回路の設計値の決定方法を提供する。 - 特許庁
When a MOS-FET12 is turned on by a control signal from a control circuit 20, current supplied from an input power supply is outputted to a load 30 while charging a capacitor 22 through a choke coil 16.例文帳に追加
制御回路20からの制御信号によりMOS−FET12がオンすると入力電源により供給された電流がチョークコイル16を介してコンデンサ22を充電しながら負荷30へ出力される。 - 特許庁
In the power source apparatus for an image forming apparatus using electrostatic photographic processing, an over-current detection value is made variable in accordance with a load mode during a printing standby time and a printing time, etc.例文帳に追加
静電写真プロセスを利用した画像形成装置用の電源装置において、プリント待機時、プリント時などの負荷モードに応じて過電流検出の値を可変にすることを特徴とする画像形成装置。 - 特許庁
To detect the failure in each output circuit even if a load current is relatively small in a DC-DC converter where a plurality of output circuits can be connected in parallel.例文帳に追加
本発明は複数の出力回路を並列に接続可能なDC−DCコンバータにおいて負荷電流が比較的小さい場合であっても各出力回路の故障の検出を可能にすることを目的とする。 - 特許庁
When discharging current to an electrical load 44 is increased, for example, when the internal combustion engine 1 is started, the charging voltage of a generator 10 is set unconditionally to a higher voltage, based on a regulated voltage Vreg.例文帳に追加
内燃機関1の始動時のように電気負荷44に対する放電電流が増大するときには、無条件に調整電圧Vreg に基づき発電機10の充電電圧が高電圧に設定される。 - 特許庁
This regulator circuit 30 is provided with an output transistor 32 feeding an output current IOUT to a load and a base board potential control circuit 36 impressing a base board potential VB to a back gate of the output transistor 32.例文帳に追加
レギュレータ回路30は、負荷に出力電流IOUTを供給する出力トランジスタ32と、その出力トランジスタ32のバックゲートに基板電位VBを印加する基板電位制御回路36とを備える。 - 特許庁
To obtain a highly accurate remaining capacity even at a high load by regenerating a corrected capacity by current integration as a corrected capacity in consideration of a temperature, without using a map comprising a battery temperature and a correction coefficient.例文帳に追加
バッテリの温度と補正係数とからならるマップを用いなくとも、電流積算による補正容量を温度を考慮した補正容量にして回生、高負荷時においても精度の高い残存容量を得る。 - 特許庁
The minimum rated current of the interlock switch 1 is made to flow in a driving load to which power is supplied through the interlock switch 1, even when the electrophotographic device is in a standby state, to instantly detect the opening/closing of the cover.例文帳に追加
インターロックスイッチ1を介して給電されている駆動負荷を電子写真装置が待機状態でも、インターロックスイッチ1の最小定格の電流を流すようにすることで、カバーの開閉を瞬時に検知する。 - 特許庁
Then, the disk rotating mechanism 100 sets the rotating direction of the magnetic disk so that a power pushing the actuator 101 to the outside of the diameter direction can be generated by the air current caused by the disk rotation in the case of the load/unload operation.例文帳に追加
そして、ディスク回転機構100は、ディスク回転による空気流によってアクチュエータ101を径方向外方に押す力がロード/アンロード動作時に発生するように、磁気ディスクの回転方向を設定している。 - 特許庁
A time T_2 can thereby be ensured after a decision is made that power is interrupted before a CPU is shut down even under a light load and current operating condition can be written in the EEPROM without using a capacitor having a large capacity.例文帳に追加
軽負荷時においても、電源遮断判定からCPUがダウンするまでに時間T_2を確保でき、大容量のコンデンサを用いることなく、現在の動作状態をEEPROMに書き込むことができる。 - 特許庁
In the overcurrent state, the switch actively controls a load current to zero, even if the sensed information is delayed or filtered significantly, or even if arriving of the switch signal from the control circuit to the switch is delayed.例文帳に追加
過電流状態では、感知された情報が遅延または激しくフィルタリングされていても、制御回路からのスイッチ信号のスイッチへの到達が遅れたとしても、スイッチは負荷電流をゼロへとアクティブに制御する。 - 特許庁
To prevent the malfunction in a CPU or a chip set mounted on a device by improving the drop of the output voltage during supply of a large current to a load without being affected by the rise time at start of a switching power source.例文帳に追加
本発明の課題は、スイッチング電源の起動時の立上り時間に影響なく、負荷への大電流供給時の出力電圧の低下を改善し、装置搭載のCPUやチップセットでの誤動作を防止することにある。 - 特許庁
When any current is not supplied from the power source part 1 to the load 3, base currents are generated at the base of the transistor Q2 by a transistor Q11 so that the transistor Q2 can be turned into an ON state.例文帳に追加
電源部1から負荷3に電流が供給されていないときにも、トランジスタQ2のベースにトランジスタQ11によってベース電流を発生させることにより、トランジスタQ2をオン状態にしている。 - 特許庁
To prevent disturbance in power supply so as to accurately measure electric current by providing a hanging cord for reducing weight and a fixing metal fitting and reducing a weight load of a clamp CT applied to an electric wire in a measurement position for protecting the electric wire.例文帳に追加
本来点検作業用として作られたクランプCT付き計測装置を本件目的の様な連続計測に使用する為、計測での電線への荷重負担をなくし、適切な固定方法が必要となる。 - 特許庁
A DC motor which is a load is inserted between a connection point of the switching elements 31, 32 and a connection point of the switching elements 33, 34, and current detection resistances 41, 42 are inserted respectively on both sides.例文帳に追加
スイッチング素子31,32の接続点とスイッチング素子33,34の接続点との間には負荷である直流モータが挿入され、その両側には、電流検出抵抗41,42がそれぞれ挿入される。 - 特許庁
To obtain a motor controller in which a dark current is prevented from flowing through a controller by interrupting the power supply to the controller after resetting the motor load when a key switch is opened.例文帳に追加
キーススイッチが開いたときにモータの負荷を原位置に復帰させてからコントローラの電源を遮断してコントローラを通して暗電流が流れるのを防止することができるようにしたモータ制御装置を提供する。 - 特許庁
Further, since the modulus of elasticity is improved, the composition and its molded product come to have flexibility, and thus the breakage of an electric current-applied circuit and the molded product by a drop impact and an external load (bending, compression, or the like) can be inhibited.例文帳に追加
また、弾性率が向上するため、組成物および成形体が柔軟性を有したものとなり、落下衝撃や外部負荷(曲げ、圧縮など)による通電回路や成形体の破壊が抑制できる。 - 特許庁
A common slow start control circuit is provided for the constant voltage control and the constant current control in an inverter circuit for driving the load such as CCFL, thus conducting slow start of PWM control in common.例文帳に追加
CCFLなどの負荷を駆動するインバータ回路における、定電圧制御及び定電流制御用に、共通のスロースタート制御回路を設けることにより、PWM制御のスロースタートを共通に行う。 - 特許庁
Abnormal operation where a current flows through a switching element with a timing, previous to ending the off period of the switching element, is eliminated during intermediate load, by setting the coupling factor k of a power insulation transformer PIT at k=0.7 or smaller.例文帳に追加
絶縁コンバータトランスPITの結合係数k=0.7程度以下として、中間負荷時において、スイッチング素子のオフ期間が終了する以前のタイミングでスイッチング素子に電流が流れる異常動作を解消する。 - 特許庁
The power-supply unit 1, in normal times, outputs a voltage between the emitter and the ground of a transistor Q1 to between output terminals 10, 11 via a resistor R2 and feeds an output current IL to a load RL.例文帳に追加
電源装置1は、通常時においては、トランジスタQ1のエミッタとグランドとの間の電圧を抵抗R2を経由して出力端10,11間に出力し、負荷RLへ出力電流ILを流す。 - 特許庁
In the S5 (step 5), when it is judged that the fuel electrode side is uniformly replaced by a fuel gas, the amount of hydrogen and the amount of air in the normal generation status are supplied and a load current at the time of normal operation is taken out.例文帳に追加
S5では、燃料極側が燃料ガスで均一に置換されたと判断した場合、通常発電状態の水素量と空気量とを供給するとともに、通常運転時の負荷電流を取り出す。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|