| 意味 | 例文 |
current valueの部分一致の例文一覧と使い方
該当件数 : 12431件
When drive current of motors respectively driving photosensitive drums is detected, and peak value of the detected current is connected as an envelope, wave shape covering fluctuations by eccentricity of the photosensitive drum is formed, accordingly, cycle of the wave shape is respectively same, however phases of the respective drums are different from each other.例文帳に追加
各感光ドラムを駆動するそれぞれのモータの駆動電流を検出して、その検出電流のピーク値を包絡線として結ぶと、感光ドラムの偏心による変動を捉えた波形になり、感光ドラム同士で波形の周期は同じであるが位相が異なる。 - 特許庁
A square error arithmetic part 71 obtains a square error of the harmonic compensation-current command value Iref0 and the actual output current Iinv1 of the AC filter, and a control unit 72 gradually increases/decreases the coefficient of the IIR filter so as to minimize the square error.例文帳に追加
二乗誤差演算部71は、高調波補償電流指令値Iref0と実際のACフィルタの出力電流Iinv1の二乗誤差を求め、制御部72は二乗誤差が最小になるように、IIRフィルタの係数を逐次増減制御する。 - 特許庁
The laser power source 12 receives the output signal from the photo diode (PD) 42 as a feedback signal, and controls the driving current or exciting current to be supplied to an LD 30 in an exciting section 24 so that the laser output of the fiber laser beam FB coincides with a set value.例文帳に追加
レーザ電源部12は、PD42の出力信号をフィードバック信号として受け取り、ファイバレーザ光FBのレーザ出力を設定値に一致させるように、励起部24のLD30に供給する駆動電流のたは励起用電流を制御する。 - 特許庁
The light emitting diode 210 is pulse-lighted by a current which has low duty, a large instantaneous value, and a very small average current using the afterglow property of eyes, and an effective visibility property is enhanced by charging power due to the generation of electricity through the limited area of the solar battery.例文帳に追加
発光ダイオード210は、目の残光特性を利用しデューティの低い瞬時値が大きく平均電流の非常に小さい電流によりパルス点灯し、限られた太陽電池の面積の発電による充電電力で実効視認特性を高める。 - 特許庁
At that time, a correction value for correcting the demand duty on the basis of the judgment result whether or not the sign of the average current corresponding to the current direction for driving the torque motor 19 in the normal/reversing direction agrees with the sign of the demand duty is determined.例文帳に追加
このとき、トルクモータ19を正転・逆転方向に駆動するための電流方向に対応する平均電流の符号と要求DUTYとの符号との一致の判定結果に基づき要求DUTYを補正するための補正量が設定される。 - 特許庁
The line interface circuit is operated in an apparent fixed current mode and generates a differential line current of about 40 mA, by using a low power source to the threshold line voltage of about 25 V which is equal to a value for which a required overhead is reduced from the voltage of the low power source.例文帳に追加
回線インタフェース回路は、見掛けじょう一定の電流モードで作動し、低電源の電圧から必要なオーバーヘッドをマイナスした値に等しい、約25Vの閾値回線電圧まで、低電源を用いて約40mAの差動回線電流を生成する。 - 特許庁
To suppress output current on power supply side to its indispensable minimum so as to reduce the power consumption and quality of generated heat, by providing a noncontact power supply facility which is arranged so that it can adjust the current value on power supply side properly, according to load on power reception side.例文帳に追加
受電側の負荷に応じて給電側の電流値を適切に調整し得るようにした非接触給電設備を提供することによって、給電側の出力電流を必要最小限に抑制して消費電力と発熱量の低減化を図る。 - 特許庁
If the total current value exceeds a total current threshold, the power management unit 21 selects a load 13 to be powered down in a predetermined order of priority and stops the power supply to the selected load 13 from the load control unit 23.例文帳に追加
電源マネジメントユニット21は、総電流値が総電流閾値を超えているとき、所定の優先順位に基づいて、電力供給禁止対象の負荷13を選択し、負荷制御ユニット23から選択した負荷13への電力の供給を停止させる。 - 特許庁
With the battery pack, the control circuit 5 controls the current interrupting element 4 in an off-state to interrupt the current, when the voltage differences of the unit batteries 1 detected by the voltage detecting circuit 2 are larger than a preset value and yet with the impact detecting part 3 in a state detecting the impact.例文帳に追加
この組電池は、電圧検出回路2が検出する素電池1の電圧差が設定値よりも大きく、かつ衝撃検出部3が衝撃を検出した状態で、制御回路5が電流遮断素子4をオフに制御して電流を遮断する。 - 特許庁
The current flowing to the light emission element is held at a desired value without being affected by characteristics of the TFT not by controlling the luminance of the light emission element with a voltage applied to the TFT, but by controlling a current flowing to the TFT by a signal line driving circuit.例文帳に追加
発光素子の輝度をTFTに印加する電圧によって制御するのではなく、TFTに流れる電流を信号線駆動回路において制御することで、TFTの特性に左右されずに発光素子に流れる電流を所望の値に保つ。 - 特許庁
To perform control of high accuracy by correctly reading out a current value of a large detection range even in a ventilating device in which a ventilation air volume width is significantly changed while performing constant ventilation air volume control of the ventilating device on the basis of the information on electric current-rotational frequency of a motor.例文帳に追加
モータの電流−回転数の情報から換気装置の換気風量一定制御を行っているが、換気風量幅が大きく可変できる換気装置にあっても、検知範囲の大きい電流値を正確に読み取って精度の高い制御を行なう。 - 特許庁
By this arrangement, the electric power necessary to the variable DC load is ensured, and the control for supplying the fixing heater with the maximum electric power within the current value set to the input current is made to efficiently execute power supply.例文帳に追加
上記により、変動するDC負荷に必要な電力を確保し、かつ入力電流に設定された電流値を超えない範囲で最大限の電力を定着用ヒーターへ供給する制御を行うことで、電源供給を効率的に行える。 - 特許庁
Thus, since current output from the amplifier circuit and the power supply circuit is predicted in advance, the sound input signal can be attenuated the basis of the predicted current value, and a sound amplifying apparatus appropriately protects the amplifier circuit and the power supply circuit.例文帳に追加
このように予め増幅回路及び電源回路が出力する電流を予測することで、電流予測値に基づき音声入力信号を減衰等することができ、音声増幅装置は、適切に増幅回路及び電源回路を保護することが可能となる。 - 特許庁
This device detects the point of an alternator-generated current Ialt becoming zero from a positive value by measuring the alternator-generated current Ialt via a voltage sensor 4 while changing the generated voltage Valt of a variable voltage alternator 2 to its reduction side by means of an ECM3.例文帳に追加
ECM3により、可変電圧オルタネータ2の発電電圧Valtを減少側に変化させつつ、電流センサ4を介してオルタネータ発電電流Ialtを計測し、オルタネータ発電電流Ialtが正の値から0となるポイントを検出する。 - 特許庁
In the detection of a fault, the initial value is read from the memory 112 to set the variable resistor 109, the voltage current converter 108 outputs the current signal to the speakers 2, the voltage signal from the speakers 2 is rectified and given to the comparators 110, 111.例文帳に追加
故障検知時には、メモリ112から初期値を読み出して可変抵抗器109を設定し、電圧電流変換器109からスピーカ2に電流信号を出力し、スピーカからの電圧信号を整流後コンパレータ110及び111に入力する。 - 特許庁
To provide a current restriction function which can reduce an output current restriction value even in an overcurrent state due to the shorting of an output terminal and the abnormality of a load and to protect a circuit element from overcurrent in an output circuit applied to a regulator circuit and a high side driver circuit.例文帳に追加
レギュレータ回路やハイサイドドライバ回路に適用される出力回路において、出力端子のショートや負荷の異常等による過電流状態でも、出力電流制限値を低くできる電流制限機能を有し、過電流から回路素子を保護する。 - 特許庁
First of all, a metal resistor, a DA converter for applying an AC voltage signal to the resister based on a digital signal A showing a sine wave signal having a fixed frequency, and a current sensor for converting a current generated in the resistor into a voltage value are provided.例文帳に追加
まず、金属製の抵抗体と、一定周波数の正弦波信号を表すデジタル信号Aに基づいて上記抵抗体に交流電圧信号を印加するDA変換器と、上記抵抗体に発生した電流を電圧値に変換する電流センサとを設ける。 - 特許庁
As a result, when a charged region is scanned by a primary electron beam, the absorption current is reduced, and a secondary electron detection signal is abnormally intensified, but the intensity of the secondary electron detection signal is reduced according to the small value of the absorption current.例文帳に追加
この結果、帯電した領域を一次電子ビームで走査しているときは、吸収電流が小さくなり、2次電子検出信号が異常に大きくなるが、この吸収電流の小さな値に応じて2次電子検出信号の強度が減少される。 - 特許庁
To provide an LD driving circuit which makes constant an average optical output of an LD at a supply destination of a driving current and also maintains an extinction ratio equal to or above a predetermined value even when current-optical output characteristics of the LD have a larger gradient.例文帳に追加
駆動電流の供給先のLDの電流‐光出力特性の傾きが大きくなっていても、当該LDの平均光出力を一定にすると共に消光比を所定値以上に維持することができるLD駆動回路の提供。 - 特許庁
An increase in the current value of drive motors 24 and 26 is detected with a current detection means 28 and 30, and when a metallic foreign matter 22 is detected as bit between the drum feeders 10 and 12, a center distance between the drum feeders 10 and 12 is increased with an actuator 20.例文帳に追加
電流検出手段28、30で駆動用のモータ24、26の電流値の上昇を検出し、ドラムフィーダ10、12の間に金属異物22が噛み込んだことを検出したときには、アクチュエータ20によりドラムフィーダ10、12の軸間距離を広げる。 - 特許庁
The charger 2 is provided with a gasoline engine, a three-phase AC generator which is driven by means of the engine, and a three-phase full-wave rectifying circuit which charges the battery 3 by rectifying the three-phase alternating current generated by means of the generator into a direct current of a prescribed value.例文帳に追加
エンジン発電式充電機2は、ガソリンエンジン、ガソリンエンジンにて駆動される3相交流発電機、3相交流発電機が発電した3相交流を所定値の直流に整流してバッテリ3を充電する3相全波整流回路を備えている。 - 特許庁
If the instantaneous fluctuations are detected by the instantaneous fluctuation detecting portion 150, a current command operating portion 110 changes the current command value to the ac motor 4, by using an Id-Iq table 114 so that the internal loss of the ac motor 4 is increased.例文帳に追加
電流指令演算部110は、瞬時変動検知部150により瞬時変動が検知されると、交流モータ4の内部損失を増加させるように、内部損失増加用Id・Iqテーブル114を用いて、交流モータ4への電流指令値を変更する。 - 特許庁
Abnormality detection circuits (3, 4) for detecting the abnormality of the current in the secondary winding of a flyback transducer (201) include a circuit (3) for converting the current of the secondary winding into a potential signal; and a circuit (407) for determining whether the potential signal is lower than a prescribed value or not.例文帳に追加
フライバックトランス(201)の二次巻線の電流の異常を検出する異常検出回路(3、4)が、二次巻線の電流を電位信号に変換する回路(3)と、電位信号が所定値よりも低いか否かを判定する回路(407)とを備える。 - 特許庁
Therefore, the change amount of the load current Io is fed back to the detecting potential Vsense of the control signal terminal 31 of a DC/DC converter 30, and the DC voltage value (Vcc) of the input signal can be decided according to the size of the load current Io.例文帳に追加
したがって、負荷電流Ioの変動分がDC/DCコンバータ30の制御信号端子31の検出電位Vsenseにフィードバックされ、負荷電流Ioの大きさに応じて入力信号の直流電圧値(Vcc)を決定することができる。 - 特許庁
In the correction table 24, the correction rate α of a current command value with respect to a rotor rotational position is determined, and it is prepared on the basis of an actual measurement result of a torque ripple generated when a predetermined reference current is fed to each phase of the electric motor M.例文帳に追加
補正テーブル24は、ロータ回転位置に対する電流指令値の補正の割合αを定めたものであり、電動モータMの各相に予め定める基準電流を供給した時に発生するトルクリップルの実測結果に基づいて作成されている。 - 特許庁
According to the instantaneous value of an input voltage (output voltage of a full-wave rectifier DB), a part of charging current to a capacitor C12 is taken in a charging current adjusting circuit 12 which is connected in parallel with the capacitor C12, thereby adjusting a voltage of the capacitor C12.例文帳に追加
入力電圧(全波整流器DBの出力電圧)の瞬時値に応じて、コンデンサC12に並列接続されている充電電流調整回路12にコンデンサC12への充電電流を一部取り込み、コンデンサC12の電圧を調整する。 - 特許庁
In this disk device, a coil resistance value and a torque constant are calculated by detecting a current and a voltage in the following of a magnetic head with a VCM (voice coil motor) current detector 30 and a VCM inter-terminal voltage detector 29 and by calculating outputs which are digitally converted in ADC (analog/digital converters) 31 in a drive control part 5.例文帳に追加
フォロイング中のVCM電流検出器29、VCM端子間電圧検出器30で電流、電圧を検出しADC31でデジタル変換された出力をドライブ制御部5で演算することで、コイル抵抗値、トルク定数を算出する。 - 特許庁
A motor current necessary for reaching the preset torque immediately before screwing the implant or the implant base using the handpiece 1 for surgical use is measured, and the motor current is limited to that value in the subsequent screwing process by controlling a motor.例文帳に追加
外科用ハンド・ピース1を使ってインプラントないしはインプラント土台をねじ込む直前に、プリセットしたトルクに達するために必要なモータ電流を測定し、モータ制御により、あとに続くねじ込み過程でモータ電流をこの値に制限することを特徴とする。 - 特許庁
Superposed voltage amplitude adjustment means 9 outputs a superposed voltage amplitude command value Vh^* for adjusting the amplitude of the alternating voltage to the voltage output means 3 on the basis of the high frequency current norm Ih from the current component separation means 5.例文帳に追加
重畳電圧振幅調整手段9は、電流成分分離手段5からの高周波電流ノルムIhに基づいて、交番電圧の振幅を調整するための重畳電圧振幅指令値Vh^*を電圧出力手段3へ出力する。 - 特許庁
A monitor current corresponding to the quantity of the emitted beams of LDs 9-1-9-3 flows to a PD 10 to be converted to monitor voltage by a current/voltage converter circuit 2 and the monitor voltage is integrated by an integration circuit 3 to be converted to an integral value S2.例文帳に追加
LD9−1〜9−4の発光光量に応じたモニタ電流がPD10に流れ、モニタ電流が電流電圧変換回路2によりモニタ電圧に変換され、モニタ電圧が積分回路3により積分されて積分値S2に変換される。 - 特許庁
Also, a current flowing in the switch when the switch is parallel-turned while there is no voltage difference and no phase difference between the feeding line of the power source A and the feeding line of the power source B is calculated based on the network impedance, and designated as a reference current value Is.例文帳に追加
また、電源Aのき電線と電源Bのき電線との間に電圧差および位相差ない状態で切替開閉器を並列投入した場合に切替開閉器に流れる電流を、回路網インピーダンスを基に算出し、基準電流値Isとする。 - 特許庁
This occurs, when the value obtained by deducting half the amount of the switching current at the switch node from the average output current is smaller than zero or equal to zero.例文帳に追加
軽負荷状態が、スイッチ・ノード(108)の電圧を監視して、負荷に依存するゼロ交差電圧を検出することによって決定され、これは平均出力電流からスイッチ・ノードに於けるスイッチング電流の半分を差引いた値がゼロより小さいかそれに等しいときに起こる。 - 特許庁
Power of an electronic control circuit 6 determining earth leakage from a zero-phase current value detected by a zero-phase current transformer 4, and power of a trip coil 8 tripping a main circuit 1 are supplied from all of three-phase voltage phases R, S and T based on a neutral phase N.例文帳に追加
零相変流器4で検出した零相電流値から漏電を判断する電子制御回路6の電源、及び主電路1をトリップさせるトリップコイル8の電源を、中性相Nを基準とした三相の電圧相R,S,Tの全てから採った。 - 特許庁
The LDD region 4707 for a current control TFT 4704 and a power supply control TFT is so formed as to be partially superposed on the gate electrode and has a structure of giving a priority to the prevention of hot carrier filling and the reduction of the off current value.例文帳に追加
電流制御用TFT4704及び電源制御用TFTのLDD領域4707は、ゲート電極に一部が重なるように形成され、ホットキャリア注入の防止とオフ電流値の低減に重点をおいた構造となっている。 - 特許庁
During the driving of the drain pump 11, the control unit 20 obatians its driving current A (S17), and it stops the drain pump 11 at the point of time when the driving current A reduces to a beforehand set prescribed value (A0×α) or below (S18, S22).例文帳に追加
制御ユニット20は、上記排水ポンプ11の駆動中にその駆動電流Aを取得し(S17)、あらかじめ設定された所定値(A0×α)以下まで上記駆動電流Aが低下した時点で上記排水ポンプ11を停止する(S18,S22)。 - 特許庁
When the power is supplied to a plurality of the in-vehicle loads having different priorities from one another, the current to the in-vehicle load having low priority is restricted so as to fall the maximum value of the current flowing from the battery 10 to the circuit unit within a tolerance.例文帳に追加
そして、互いに優先度の異なる複数の車載負荷へ給電を行うときには、前記バッテリー10から前記回路体に流れ込む電流の最大値を許容範囲内に収めるべく、優先度の低い車載負荷に対する電流を制限する。 - 特許庁
The disposed diode uses junction which is equivalent to the p-n junction between the source and bulk of the MOSFET and the bias voltage is applied to the back gate of the MOSFET by using a voltage generated across the anode and cathode of the diode when the diode is driven by a constant current having a certain current value.例文帳に追加
そのダイオードは該MOSFETのソースーバルク間のPN接合と同等の接合を用い、配置したダイオードをある電流値で定電流駆動し、該ダイオードのアノードーカソード間に発生する電圧で該MOSFETのバックゲートにバイアスを与える。 - 特許庁
To suppress the heating in switching to suppress the noise by a sudden change in voltage or current in an electromagnetic induction-heating rice cooker for performing heating by carrying a high frequency current to a coil by performing the switching at a proper timing regardless of the value of power supply voltage.例文帳に追加
コイルに高周波電流を流すことにより加熱する電磁誘導加熱式炊飯器において、電源電圧の値によらず適正なタイミングでスイッチングを行い、スイッチング時の発熱を抑え、急峻な電圧や電流の変化によるノイズを抑制する。 - 特許庁
Since the input/output controller controls input/output of the secondary battery by using both the measured current It and estimated current Is, a remarkable increase in a calorific value of the secondary battery and that of a peripheral component of the secondary battery can be suppressed more securely.例文帳に追加
入出力制御装置は、実測電流Itだけでなく推定電流Isも用いて、二次電池の入出力を制御するので、二次電池の発熱量や二次電池の周辺部品の発熱量が大幅に増えるのをより確実に抑えることができる。 - 特許庁
When any one of motor drive wires 4 is disconnected, a drive control means 1 further increases a current command value 1a of the corresponding phase since a current does not flow in the motor drive wire 4 even if the drive control means 1 applies a voltage to a drive circuit 2.例文帳に追加
いずれかのモータ駆動線4が断線している場合には、駆動制御手段1は、駆動制御手段1が駆動回路2に電圧を印加しても該モータ駆動線4に電流が流れないので、該相の電流指令値1aをより大きくする。 - 特許庁
A bias condition of a selection transistor connected to the variable resistive element in series is set so that the amount of current flowing to the variable resistive element during forming processing is smaller than a maximum value of the current flowing to the variable resistive element during setting (reduction in resistance).例文帳に追加
フォーミング処理時において可変抵抗素子に流れる電流量が、セット(低抵抗化)時に可変抵抗素子に流れる電流の最大値よりも小さくなるように、可変抵抗素子と直列に接続する選択トランジスタのバイアス条件を設定する。 - 特許庁
In the memory element, information written in the magnetic body 10 can be read by detecting the current value of the current flowing in the first wiring 14 when electrons are moved from the second wiring 15 to the first wiring 14.例文帳に追加
この記憶素子は、第2の配線15から第1の配線14に電子を移動させた場合において、第1の配線14に流れる電流の電流値を検出することによって、磁性体10に書き込まれた記憶情報を読み取るようになっている。 - 特許庁
When the integrated value of the steering torque integrated at this torque integrating part 72 is out of a specified range, the wheel for steering is judged to be steered to the neighbourhood of the maximum steering angle, and an assist limiting electric current is set at an assist limiting electric current setting part 73.例文帳に追加
このトルク積算部72において積算された操舵トルクの積算値が所定範囲外であれば、舵取り用車輪が最大転舵角付近まで転舵されていると判断され、アシスト制限電流設定部73においてアシスト制限電流が設定される。 - 特許庁
To provide a laser current meter type portable tube instantaneous flow meter in a sandwich structure for easily mounting an optical system for laser current meters for measuring tube center velocity by the laser current meter, obtaining a sectional flow rate from simulation calculation, and obtaining an instantaneous value in real time without disturbing the flow without any contact compactly on piping.例文帳に追加
レーザー流速計で管中心速度を測定し、シミュレーション計算から断面流量を求め、非接触で流れを乱さずに、瞬間値がリアルタイムに得られるレーザー流速計用光学系を、小型で、配管上に容易に取り付けられるようにした挟み込み構造のレーザー流速計式ポータブル型管内瞬間流量計を提供する。 - 特許庁
The control device for the motor-driven actuator reducing a clutch lever operation load of the motorcycle and the engine-assisted bicycle is provided with a rotation angle detection sensor detecting rotation angle of the clutch lever and a motor amplifier for generating a current in a current amplifier according to a current command value proportional to an output of the rotation angle detection sensor.例文帳に追加
自動二輪車や原動機付自転車のクラッチレバー操作荷重を低減する電動アクチュエータ用制御装置において、前記クラッチレバーの回転角を検出する回転角度検出センサーを備えると共に、該回転角度検出センサーの出力に比例した電流指令値により電流アンプに電流を発生させるモーターアンプを備える。 - 特許庁
The deposit height measuring instrument includes current applying electrodes 11, 12 for applying a current within a plating bath and voltage measuring electrodes 21, 22 for measuring the voltage generated by the applied current; and estimates the deposition height of the deposits precipitated within the plating bath based on the voltage value measured between the voltage measuring electrodes 21, 22.例文帳に追加
堆積物高さ測定装置は、めっき浴内に電流を印加する電流印加用電極11,12と、その印加された電流によって発生する電圧を測定する電圧測定用電極21,22とを備え、電圧測定用電極21,22間で測定される電圧値に基づいて、めっき浴内に沈殿する堆積物の堆積高さを推定する。 - 特許庁
Each of the direct-current outlets 1 includes: a communication circuit 4 that receives the measurement value of the amount of current transmitted from the transmission processing unit 30; multiple light-emitting diodes 6a to 6d; and a display control circuit 5 that causes a corresponding light-emitting diode 6a to 6d to emit light based on the measured amount of current received by the communication circuit 4.例文帳に追加
また各直流コンセント1に、伝送処理部30から伝送された電流量測定値を受信する通信回路4と、複数個の発光ダイオード6a〜6dと、通信回路4が受信した電流量測定値に基づいて対応する発光ダイオード6a〜6dを発光させる表示制御回路5とを備えている。 - 特許庁
The current supply circuit is so constituted that the resistance values of the path over the entire part of the current flowing during the supply, even if the currents are selectively supplied, in such a manner that the Lorentz force is generated in the prescribed direction in any of coils (Lorentz force current paths) L 11 to L13, L 21 to L 23, and L 31 to L 33 are substantially the same value.例文帳に追加
電流供給回路は、いずれのコイル(ローレンツ力電流経路)L11〜L13,L21〜L23,L31〜L33に所定方向にローレンツ力が生ずるように選択的に電流を供給しても、当該供給時に流れる電流の全体経路の抵抗値が、互いに実質的に同一となるように、構成される。 - 特許庁
A CPU 3 for measurement, every when creating measured data, compares current measured data and measured data stored in a memory M 2 which is previously determined to be radio transmitted, and determines the current measured data to be radio transmitted if the current measured data becomes greater than a predetermined value, then notifies to a CPU 4 for transmission.例文帳に追加
計測用CPU3は、計測データを作成する毎に、今回の計測データとメモリM2に保存されている前回無線送信すべきと判断された計測データとを比較し、今回の計測データに所定値を超える変化が認められた場合、今回の計測データを無線送信すべき計測データと判断し、送信用CPU4に通知する。 - 特許庁
Even if an oscillation current is supplied to a pulse generation circuit to maintain a semiconductor switching circuit in on-state, since self-hold type two terminal semiconductor switching element 15 having larger maintaining current value is connected in series, the two terminal semiconductor switching element 15 can not be maintained in on-state by the oscillation current.例文帳に追加
振動電流がパルス発生回路に流れて制御極付半導体スイッチング素子16をオン状態に保持しようとしても、より保持電流値が大きい自己保持形の2端子半導体スイッチング素子15が直列的に接続されているため、前記振動電流によってもこの2端子半導体スイッチング素子15はオン状態に保持することができなくなる。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|