| 意味 | 例文 |
current-valueの部分一致の例文一覧と使い方
該当件数 : 12431件
To provide a motor controller capable of accurately controlling a brushless motor by determining a voltage command value indicating voltage to be applied to the brushless motor using an estimated current value even though a current sensor is not provided.例文帳に追加
電流センサを備えていなくても、電流推定値を用いてブラシレスモータに印加すべき電圧を示す電圧指令値を求めることにより、ブラシレスモータを高精度で制御することができるモータ制御装置を提供する。 - 特許庁
The current command value operating unit 25 outputs the angular velocity difference compensation Ir* superposed on the basic assist quantity Ias* which is the basic control quantity of the assist force to a motor control signal output unit as the current command value Iq*.例文帳に追加
そして、電流指令値演算部25は、この角速度差補償量Ir*をアシスト力の基礎的制御量である基礎アシスト量Ias*に重畳した値を、電流指令値Iq*としてモータ制御信号出力部26に出力する。 - 特許庁
The electrooptical device is further provided with a luminance detecting part which detects the luminance of the electrooptical element and a drive current value adjustment part which adjusts the value of drive current in accordance with the detected result of luminance obtained on the luminance detecting part.例文帳に追加
電気光学素子の輝度を検出する輝度検出部と、電気光学素子の輝度を補正すべく、輝度検出部で得られた輝度検出結果に基づき駆動電流量を調整する駆動電流量調整部とを備える。 - 特許庁
The fault-sending device of the current sensor estimates a deviation Δw of a current value, due to the time difference of sampling timings by an error estimating unit 11, and corrects (corrects X to X+Δw) a fault decision value by a decision condition correcting unit 12 by using the result.例文帳に追加
誤差推定部11において、サンプリングタイミングの時間差による電流値のズレ△wを推定し、その結果を用いて判定条件補正部12において故障判定値の補正(XをX+△wに補正)を行う。 - 特許庁
The duty ratio corresponding to grip opening Th is set to a duty map 48 beforehand and a current value when energizing to a motor 18 by the voltage value decided by the duty ratio is set to discharge current map 49.例文帳に追加
グリップ開度Thに応じたデューティ比をデューティマップ48に予め設定しておくとともに、そのデューティ比によって決定される電圧値でモータ18に通電したときの電流値を放電電流マップ49に設定しておく。 - 特許庁
Since the potential of a node B is almost constant with respect to the change of the level of a delay signal Iu and the potential of a node A is also almost constant, because the internal resistance value of the 1st current path is almost equal to the internal resistance value of the 2nd current path.例文帳に追加
第一の電流路の内部抵抗値と第二の電流路の内部抵抗値がほぼ等しいため、ノードBの電位は遅れ信号Iuのレベルの変化に対してほぼ一定であり、ノードAの電位もほぼ一定になる。 - 特許庁
On the other hand, when the direct-current power supply potential generated in the rectification circuit 102 is less than or equal to the predetermined value (reference value), the protection circuit 107 is not operated, and the generated direct-current power supply potential is used without any change.例文帳に追加
一方、整流回路102において生成された直流電源電位が所定の値(基準値)以下となるときは、保護回路107が動作しないようにし、生成された直流電源電位の値をそのまま用いる。 - 特許庁
In the period, light emitting brightness is controlled so that the light emitting brightness of the organic EL element does not receive influence of temperature on the basis of a value of the detected drive current and a value of the drive current at the prior time point.例文帳に追加
そして、その期間においては、検出された駆動電流の値と、それ以前の時点での駆動電流の値とに基づいて、有機EL素子の発光輝度が温度の影響を受けないような、発光輝度の制御も行われる。 - 特許庁
A PWM command value corresponding to the composite signal Sum and a signal Sp indicating the position is outputted from a PWM command value generating circuit 40 and a driving current corresponding thereto is outputted through a current feedback circuit 51.例文帳に追加
合成信号Sumと位置を示す信号Spに応じたPWM指令値がPWM指令値発生回路40から出力され、これに応じた駆動電流が電流フィードバック回路51を介して出力される。 - 特許庁
To solve the problem of an apparatus of capacitor input of a conventional type such that an input current of the apparatus of this type is a steep current and particularly forms a current waveform containing an odd harmonic- current component, and a receiving/distribution facility is thus uneconomical in its utility value and an induction trouble or the like is easy to occur by a harmonic current.例文帳に追加
この種の、コンデンサ入力の機器において、入力電流は非常に急峻な電流が流れ、特に、奇数次の高調波電流成分を含む電流波形となり、受配電設備の利用度を考えると不経済であり、又、高調波電流によって誘導障害等が発生する。 - 特許庁
When a voltage of the first signal is lower than a voltage value of a reference voltage source 15, for example, this is detected by a comparator 13, a switch circuit 12 is switched to the side of a first current source 6, a current of a third current source 11 flows to the first current source 6, and a current is blocked from flowing to a first differential couple 4.例文帳に追加
例えば第1の信号の電圧が基準電圧源15の電圧値未満の際には、比較器13がこれを検知して、スイッチ回路12が第1の電流源6側に切換わり、第3の電流源11の電流が第1の電流源6に流れて、第1の差動対4に電流が流れることが阻止される。 - 特許庁
A micro step drive control section 53 increases a current supply period of the drive current by setting supply time multiplied by a coefficient according to the current amplitude as a current supply period at time of carrying out the micro step drive when the current amplitude at the time of two phase excitation drive is larger than a reference value.例文帳に追加
マイクロステップ駆動制御部53は、二相励磁駆動時の電流振幅値が基準値に対して大きい場合には、マイクロステップ駆動する際の電流供給時間として、電流振幅値に応じた係数を乗じた供給時間幅を設定することで、駆動電流の電流供給時間を増加させる。 - 特許庁
An AC current value and a power factor angle are determined by using the current sensors of a DC section and the current sensors for one phase of outputted alternating current, and a means of determining a switching pattern of a DC main element and a current component of Idc or a means of detecting the maximum of Idc.例文帳に追加
直流部の電流センサと出力交流電流の1相分の電流センサを用い、かつ、直流主素子のスイッチングパターンを判定し、Idcの電流成分を判定する手段、又はIdcの最大値を検出する手段を用いて、交流電流値及び、力率角を求める。 - 特許庁
A terminal device 3 installed at customers A, B or the like determines occurrence of leakage current based on the information on leakage current and current direction detected by an momentary power failure detecting sensor 5, and transmits information showing occurrence of leakage current and the current value as thunderbolt pulse data to the momentary power failure prediction device 1 via the Internet 2.例文帳に追加
顧客A,B等に設置された端末装置3は、瞬低検知センサー5が検知した漏洩電流及び電流方向の情報から漏洩電流の発生を判断し、落雷パルスデータとして漏洩電流の発生を示す情報及び電流値をインターネット2を介して瞬低予測装置1へ送信する。 - 特許庁
There are provided a first current limiting circuit 40 of high gain and low response type which detects an output current Io of an output circuit 20 and generates a current limiting signal respectively when the output current Io exceeds a predetermined value, and a second current limiting circuit 50 of low gain and high response type.例文帳に追加
この出力回路20の出力電流Ioを検出して、この出力電流Ioが所定値を越えたときにそれぞれ電流制限信号を発生する、高利得で低速応答型の第1電流制限回路40と、低利得で高速応答型の第2電流制限回路50とを設ける。 - 特許庁
In this current conduction, firstly, electric current of a constant formation current density is flown continuously and after the voltage between the positive electrode and the negative electrode has increased by a specified amount, the voltage between the positive electrode and the negative electrode is maintained at the increased voltage, and when the formation current density has decreased to the prescribed value, the electric current conduction is stopped.例文帳に追加
この通電では、まず一定の化成電流密度の電流を流し続けて正極と負極との間の電圧が規定量だけ増加した後は正極と負極との間の電圧を増加後の電圧に維持して化成電流密度が所定値まで減少したときに通電を停止させる。 - 特許庁
Current mirror transistors are inserted in series into at least one of paired transistors included in a plurality of push-pull configuration output stages, a common transistor is provided for forming a current mirror circuit with each of these current mirror transistors, and a value of mirror current flowing in the common transistor is set by a mirror current setting circuit.例文帳に追加
複数のプッシュプル構成の出力段に含まれる一対のトランジスタの少なくとも1つに直列にカレントミラー用トランジスタを挿入し、これらのカレントミラー用トランジスタの各々とカレントミラー回路を形成する共通トランジスタを設けて、共通トランジスタを流れるミラー電流値をミラー電流設定回路によって設定する。 - 特許庁
A laser current detecting circuit 15 for detecting a current (laser current) flowing through a laser diode under stable control of a laser emitting output is provided, the laser current value detected by the laser current detecting circuit 15 is stored in a flash ROM 104 with a fixed period together with data of an operation accumulated time of a laser unit.例文帳に追加
レーザ発光出力の安定化制御のもとでレーザダイオードを流れる電流(レーザ電流)を検出するレーザ電流検出回路15を設け、このレーザ電流検出回路15により検出されたレーザ電流値をレーザユニットの稼働累積時間のデータとともに一定周期でフラッシュROM104に記憶する。 - 特許庁
Since the solenoid driving current I is controlled to be set to the target current value IT after overshooting and undershooting the current I in this way, the attracting force of the solenoid actuator is fixed at an intermediate point of the difference between the attracting force characteristics of the actuator in the current increasing direction and current decreasing direction of the actuator, and the hysteresis characteristic of the actuator can be negated.例文帳に追加
このように、ソレノイド駆動電流を増減振動させた後に目標電流値に収束するように制御することにより、ソレノイドアクチュエータの電流増加方向と電流減少方向との吸引力特性の偏差の中間点に吸引力が落ち着き、ヒステリシス特性を打消すことができる。 - 特許庁
The inverter device includes: an inverter circuit 13 driving the permanent magnet synchronous motor 11 connected to a DC power source 12; current detection means 14 detecting motor current or DC current; and control means controlling the permanent magnet synchronous motor 11 by using a current detection value detected by the current detection means 14.例文帳に追加
そして、インバータ装置は、直流電源12に接続された永久磁石同期モータを駆動するインバータ回路13と、モータ電流または直流電流を検出する電流検出手段14と、電流検出手段が検出した電流検出値を用いて永久磁石同期モータを制御する制御手段を有する。 - 特許庁
Thus, the current value flowing the cell 10a can be accurately detected even if a resistance value of the resistor 121 between the first and second through-holes 101a, 101b is changed.例文帳に追加
これにより、第1、第2スルーホール101a、101b間の抵抗体121の抵抗値に変化が生じても、セル10aを流れる電流値を精度良く検出できる。 - 特許庁
When the control device determines that the behavior of the current value is lower than a predetermined value and that a failure occurs in the radiator fan motor, the device regulates engine output.例文帳に追加
そして当該電流値の挙動が所定値よりも低く、ラジエータファンモータに異常を来たしたと判断した場合には、エンジンの出力を制限するようにしている。 - 特許庁
The reference voltage Vd is predetermined as a value corresponding to the lower limit current value of the supply currents I necessary for normally operating the main body circuit 2.例文帳に追加
基準電圧Vdは本体回路2を正常に動作させるために必要な供給電流Iの下限電流値に応ずる値として予め定められている。 - 特許庁
In this case, a lower limit value for the solenoid force F2 is determined by a lower limit value for a current actually flowing in a coil 178 and by a lower limit pulse width of a FET 242.例文帳に追加
この場合において、ソレノイド力F2 の下限値は、コイル178に実際に流れる電流の下限値によって決まり、FET242の下限パルス幅によって決まる。 - 特許庁
In the valve driver 25, a voltage value is converted into a current value, and damping force is controlled by driving a valve of an air spring 12 having first to forth variable damper therein.例文帳に追加
バルブドライバ25では電圧値を電流値に変換し、1位〜4位の各可変減衰ダンパ内蔵型空気ばね12のバルブを駆動して、減衰力を制御する。 - 特許庁
To avoid waste of operation time in a method for manufacturing high-frequency components which uses a predictive voltage value and a predictive current value, from a certain point of time up to another time point.例文帳に追加
ある時点からある時点までの予測電圧値、予測電流値を用いる高周波部品の製造方法において、その演算時間の無駄を省くことである。 - 特許庁
In this case, it is regarded as the sudden event (S60, S70, S80) when the average value of the current road density is larger than the upper limit value of the previous road density for the fixed period of time.例文帳に追加
この際、一定時間の間現在の道路密度の平均値が以前の道路密度の上限値より大きい場合に突発事象と決める(S60、S70、S80)。 - 特許庁
Then, an average actual opening TA is obtained by carrying out an averaging process after adding a current converted value VTAAD to a last converted value VTAADO (110).例文帳に追加
次に、今回の変換値VTAADと前回の変換値VTAADOを足し合わせて平均化処理することにより平均実開度TAの値を得る(110)。 - 特許庁
The control means 11 controls, with the pulse width modulation (PWM), the current value of the paper feed clutch 104 at a value obtained when the connection of the paper feed clutch is detected.例文帳に追加
制御手段11は、給紙クラッチ104の電流値を、給紙クラッチ連結を検出した時の値になるようにパルス幅変調(PWM)で制御する。 - 特許庁
A heat value calculation unit 4B converts the eddy current at every element calculated by the magnetic field analyzing part 4A to the heat value at every element in the heat treatment analyzing FEM model.例文帳に追加
発熱量算出部4Bは、磁場解析部4Aが求める要素毎の渦電流を熱処理解析用FEMモデルにおける要素毎の発熱量に変換する。 - 特許庁
Time when the difference ΔI indicating reduction amount of the current value exceeds a predetermined value is determined as molten metal surface detection time ta which is time when the stirring member reaches the molten metal surface.例文帳に追加
電流値の減少量である差ΔIが予め定める値以上になる時を、撹拌部材が湯面に到達する時である湯面検知時taと判断する。 - 特許庁
A monitoring range of an upper limit value and a lower limit value for an arbitrary welding voltage and a welding current, a delay time of the beginning of monitoring, and the number of alarm paths are preliminarily stored at a work memory 15.例文帳に追加
任意の溶接電圧・溶接電流に対する上限値、下限値の監視範囲、モニタ開始遅延時間、アラームパス回数をワークメモリ15に予め格納する。 - 特許庁
Thereby, the current flowing through the heater is stabilized at a predetermined value, so that power supplied to the heater 112 is kept at a predetermined value.例文帳に追加
これにより、ヒータに流れる電流は所定値に安定するので、ACライン電圧が変動しない限り、ヒータ112に供給される電力は所定値に保持される。 - 特許庁
A difference between a default set value and the current set value is displayed on the printer setting GUI screen 602 so that the user can easily confirm changes in printer settings.例文帳に追加
プリンタ設定GUI画面602にデフォルト設定値と現在の設定値の差分を表示することによりユーザーが、プリンタ設定の変更点を容易に確認できる。 - 特許庁
A difference between a default set value and the current set value is displayed on the printer setting GUI screen 602 so that the user can easily confirm changes in printer settings.例文帳に追加
プリンタ設定GUI画面602にデフォルト設定値と現在の設定値の差分を表示することにより、ユーザーがプリンタ設定の変更点を容易に確認できる。 - 特許庁
A current label value is replaced with a label value reserved for the packet originated from a port related to a VLAN in a second switching node from the last of the LSP.例文帳に追加
LSPの最後から2番目のスイッチングノードにおいて、現行のラベル値は、VLANに関連付けられたポートから発信するパケットのために予約されたラベル値と置き換えられる。 - 特許庁
The frequency of AC current is modulated into at least a first value and a second value having a higher audible sensitivity than the first frequency except for a preset period after the startup operation.例文帳に追加
始動動作後から一定期間を除いては交流電流の周波数を少なくとも第1の値と第1の値よりも可聴感度の高い第2の値とに変調する。 - 特許庁
The electrode elevating device 40 vertically moves the electrode 50 according to the targeted current value calculated by the control circuit 30 and thereby adjusts the arc resistance value.例文帳に追加
電極昇降装置40は、電圧・電流制御回路30が算出した目標電流値に応じて電極50を昇降させ、これによって、アーク抵抗値を調整する。 - 特許庁
The storage section stores the current value of the digital audio signal output from the calculation section as a previous value of the digital audio signal used for next comparison.例文帳に追加
前記記憶部は、前記演算部から出力された前記デジタル音声信号の最新値を、次回の比較で用いられる前記デジタル音声信号の前回値として記憶する。 - 特許庁
Then, the target potential is obtained by adjusting a voltage value applied to a grid by a grid voltage adjusting means 53 in a state where the stored current value is applied to the discharge wire.例文帳に追加
記憶された電流値を放電ワイヤーに印加した状態で、グリッド電圧調整手段53によりグリッドに印加する電圧値を調整して目標電位を得る。 - 特許庁
To reduce man-hour by verifying layout data whether wiring accords with a constraint value, by calculating the constraint value of wiring width based on the wiring allowable current of an integrated circuit.例文帳に追加
半導体集積回路の配線許容電流から配線幅の制約値を求め、レイアウトデータで制約値通りの配線か否かを検証して工数を削減する。 - 特許庁
A disconnection determination circuit 168 outputs a disconnection determination signal when a comparative result between a motor current value and the disconnection determination value satisfies a prescribed disconnection determination condition.例文帳に追加
断線判定回路168は、モータ電流の値と断線判定値の比較結果が所定の断線判定条件を満たす場合に断線判定信号を出力する。 - 特許庁
The EPSECU gradually reduces a current command limit value I*_lim and a boost voltage limit value Vbp_lim before starting the cranking when the notification is received.例文帳に追加
そして、EPSECUは、該通知があった場合には、そのクランキングが開始される前に、電流指令制限値I*_lim及び昇圧電圧制限値Vbp_limを漸次低減する。 - 特許庁
The control unit 6 calculates a power given to the tip 9 based on a voltage value and a current value applied to a piezoelectric vibrator of the ultrasonic welding device 4.例文帳に追加
制御装置6は超音波溶着機4の圧電振動子に印加された電圧値と電流値に基づいてチップ9に加えられた仕事率を算出する。 - 特許庁
After minute charging in which preliminary charging is performed for a few seconds, the output value (current value) of an AD converter 5 under the condition of charging being stopped is temporarily stored in a RAM 8.例文帳に追加
予備充電を数秒間行う微少充電を行った後、充電停止状態でのAD変換器5の出力値(電流値)をRAM8に一時保存する。 - 特許庁
The calculation/determination part 200 acquires life determination data based on the bearing state data (the startup time count value and the motor current count value) after elapsing a predetermined time period.例文帳に追加
また、演算・判定部200は、所定時間を経過した後のベアリング状態データ(起動時間カウント値およびモータ電流カウント値)に基づく寿命判定データを取得する。 - 特許庁
An electric current value at which toner is flying is detected in the developing section, and a developing bias condition is determined so as to minimize difference in phase between the value and a predetermined high-frequency development bias applied.例文帳に追加
現像部でのトナー飛翔電流値を検知し、印加した所定の高周波現像バイアスとの位相のズレを最小化するように現像バイアス条件を定める。 - 特許庁
The found peak value ΔV is compared with a useful-life determination reference value Vref, and further, the peak current reaching time Δt is compared with a determination reference time Tref.例文帳に追加
そして、求めたピーク値ΔVを寿命の判定基準値Vrefと比較し、さらにピーク電流到達時間Δtを判定基準時間Trefと比較する。 - 特許庁
Preferably, the abnormality caused by the clogging of the AI piping 12 is determined when the internal pressure is not lower than a prescribed value and the applied current is not smaller than a prescribed value.例文帳に追加
好ましくは、内部圧力が所定値以上であり、且つ、印加電流が所定値以上である場合に、AI配管12の詰まりによる異常を判定する。 - 特許庁
The setting item to be returned from the current setting value to the default value is selected from the plurality of displayed setting items on the basis of operation of the user (S106).例文帳に追加
そして、表示された複数の設定項目の中で、現在の設定値をデフォルト値に戻す設定項目が、ユーザの操作に基づいて選択される(S106)。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|