| 意味 | 例文 |
outer caseの部分一致の例文一覧と使い方
該当件数 : 4410件
The pipe 10 has a projection 18 projecting outside from an outer peripheral surface, and is connected to the motor in a state of engaging the projection 18 with a rear end surface 19 of a rear case 16.例文帳に追加
パイプ10は、外周面から外側に突出する突起18を有し、突起18がリアケース16の後端面19に係合した状態でモータに接続している。 - 特許庁
An annular holder member 12 which forms a reinforcing member is fitted to the outer periphery of a switch case 71 which forms the shell of a maximum bet button 7 in such a way as to prevent loosening.例文帳に追加
MAXベットボタン7の外観を形成するスイッチケース71の外周に、補強部材を形成する環状保持部材12を抜け止め可能に外嵌する。 - 特許庁
In the case of not using the gap nozzle, the flange part 166 of the furniture brush is fitted and connected to the tip part of the hose without causing a gap between the tip part of the hose and the outer circumferential surface of the connecting pipe part 163.例文帳に追加
隙間ノズルを用いない場合、ホースの先端部に家具ブラシのフランジ部166を嵌合して連通管部163の外周面との間に隙間を生じずに接続する。 - 特許庁
When a vehicle collides against an obstacle, a large force is applied in the direction shown by an arrow in the drawing, and the outer circumferential walls 73 and 74 of the inverter case 49 are destroyed.例文帳に追加
自動車が障害物に衝突したような場合、矢印で示す方向に大きな力が加わり、インバータケース49の外周壁73、74は破壊される。 - 特許庁
A case forming an outer shell of the switch box 11 is formed of, for example, synthetic resin, and the switch box 11 is equipped with an operation part 16 operating the built-in switch.例文帳に追加
スイッチボックス11の外殻を形成するケースは、例えば合成樹脂から成り、このスイッチボックス11は、内蔵されるスイッチを操作する操作部16を備えている。 - 特許庁
In this case, also the outer peripheral side of a coupling surface between the flow passages 12 and 17, the gasket 19 is nipped by an inner ferrule 13 grasped at the pipe 11 and a fastening member 17.例文帳に追加
このとき、流路12、17の連結面の外周側においても、パイプ11に握着されたインナーフェルール13と締付部材17で、ガスケット19を挟持している。 - 特許庁
In this case, a gap between the outside end in an axial direction of the intermediate metal fitting 16 and a caulked end 12a of the outer cylindrical metal fitting 12 is sealed by an extending piece 17 of the rubber elastic element.例文帳に追加
このとき、ゴム弾性体の延出片17によって中間金具16の軸方向の外側端と外筒金具12のかしめ端12aの間をシールする。 - 特許庁
When transferring cash, the specification slip, which has issued in the last transfer, is inserted into an auxiliary case for transfer with the same outer size as that of a cash card or a transfer card.例文帳に追加
現金振込を行うときに、キャッシュカードや振込カードと同じ外形サイズの振込用補助ケースに、前回の振り込みの際に発行された明細票が挿入される。 - 特許庁
Further, the spacing between the inner surface of the case for the packaging bag and the outer surface of the packaging bag is preferably smaller as being farther from the opening part at least in a part thereof.例文帳に追加
また、包装袋用ケースの内面と、包装袋の外面との間隔は、少なくとも一部において、開口部から離れるにしたがって狭くなることが好ましい。 - 特許庁
Then, it shows substantially the same outer shape as that of a plastic case by folding the storage holder 1 with the first to sixth melting and fixing portions S1 to S6 and the first to sixth folding lines K1 to K6.例文帳に追加
そして、収納ホルダ1を第1〜第6溶着部S1〜S6及び第1〜第6折り目K1〜K6にて折り畳むことにより、プラケースとほぼ同じ外形となる。 - 特許庁
An oil scattered space 98 extending to the second transverse walls 74 from the first transverse walls 73 in the vicinity of the outer peripheral surfaces of the crank webs 6c, 6d is formed in the crank case 2.例文帳に追加
クランクケース2に、クランクウェブ6c,6dの外周面の近傍を第1の横壁73から第2の横壁74まで延びるオイル飛散用空間98を形成する。 - 特許庁
This housing room 4 is supported by link members 5 facing each other on both sides, and made to be rotated, and then arranged at a using position located inside the outer case 2 and downward of its front side and arrangement- freely formed.例文帳に追加
この収納庫4を相対する両側のリンク部材5で支持して回動させ、外筐体2内とその前側下方の使用位置に配置自在に形成する。 - 特許庁
The outer case 3 is internally divided into the front refrigerating chamber 6 for housing the storage body 4, and a rear equipment chamber 7 for housing the Peltier elements 16, the heat exchangers and the like.例文帳に追加
外ケース3の内部は、収納体4を収容する前方の冷蔵室6と、ペルチェ素子16および熱交換器等を収容する後方の機器室7とに区分する。 - 特許庁
Further, the case 1 is provided with a second engagement portion 12 to engage the first engagement portion 25A inside the outer peripheral sidewalls 16 to 18 when the cover 2 is mounted.例文帳に追加
またケース1に、カバー2が装着された際に外周側壁16〜18の内側で第1の係合部25Aと係合する第2の係合部12を設ける。 - 特許庁
The elastic sheet 11 has projecting parts 11a projecting from the outer periphery of the isolation member 6 used for projecting packing 15 for closing a space between a holder case 3 and itself.例文帳に追加
弾性シート11は、隔離部材6の外周縁から突出する突出部分11aをホルダーケース3との間の隙間を閉塞する突出パッキン15としている。 - 特許庁
An outer shell magnetic circuit 33 consisting of a magnet 37, a pole piece 38, and a top plate 39 is supported in a case with support springs A (36), B (42) to form a vibration section.例文帳に追加
磁石37、ポールピース38、トッププレート39からなる外磁型の磁気回路部33を、支持ばねA(36)、支持ばねB(42)でケース中に支持して振動部とする。 - 特許庁
The substrate case 400 is attached and fixed to the inside face 221 of the back board 220 of the outer casing body 2 via right and left bracket members 301, 302.例文帳に追加
基板ケース400は、左右のブラケット部材301、302を介して外装筐体2の背板220の内側面221に取り付け固定されるようになっている。 - 特許庁
One end of the stator section 10 is covered with a resin cap 18 and a motor cover 23 is formed by resin molding the outer circumferential portion of the cap 18 and the case 3.例文帳に追加
ステータ部10の一端部を樹脂製のキャップ18にて蓋をすると共に、キャップ18およびケース3の外周部を樹脂モールドしてモータカバー23を形成する。 - 特許庁
A locking protrusion 4 is formed on the outer surface of the fixing nail part 3, or the axial direction of the fixing nail part 3 is inclined to the plane containing the net receiving part 2 in some case.例文帳に追加
固定釘部3の外面に抜け止め突部4を形成したり、ネット受け部2を含む平面に対して固定釘部3の軸方向を傾斜させることがある。 - 特許庁
The air-conditioning apparatus 1 includes a medicine container 3 filled with the liquid composition 31, a ventilation cylinder 5, and a fan 6 for feeding air into the ventilation cylinder 5 in an outer case 2.例文帳に追加
空気調整機器1は、外装ケース2内に、液状組成物31が充填された薬用容器3と、通気筒5と、通気筒5内に送風するファン6とを備える。 - 特許庁
The soft foam on the outer peripheral edge of the seal member 31 pressure-contacted with at least an inner surface of the case body 11 is crushed, and the crushed part 36 is formed.例文帳に追加
該シール部材31の少なくともケース体11の内面に圧接される外周縁における軟質発泡体は潰されて潰れ部36が形成されている。 - 特許庁
To provide a packaging device having a sufficient strength even if its configuration is simple even under a case in which a large-sized cargo is to be packaged and further showing a beautiful outer appearance.例文帳に追加
大型貨物を梱包する場合であっても、簡易な構成でありながら十分な強度を有し、さらに、外観上も美しい梱包装置を提供すること。 - 特許庁
The portable power supply device 100 has a case 102 having an opening at least on one side and an outer package part constituted of a lid 104 to seal the opening.例文帳に追加
可搬式電源装置100は、少なくとも一面に開口部を有する筐体102と、開口部を封止する蓋104で構成された外装部を有している。 - 特許庁
If an outer case is deformed by falling down of the portable telephone or due to other cause, the two semiconductor devices 10, 11 are influenced by the deformation, come in contact with each other and exert pressing force on each other.例文帳に追加
携帯電話機を落とすなどして外ケースが変形すると、その影響を受けて2個の半導体デバイス10,11が互いに接触して押圧力を及ぼし合う。 - 特許庁
Recessed parts 30 are provided on both side surfaces of a main body case 7 on whose outer surface the anodized aluminum layer is provided and which is electrically connected to the ground terminal of a circuit board on its inner surface.例文帳に追加
外面にアルマイト層が設けられ、内面で回路基板の接地端子と電気的に接続された本体ケース7の両側面には凹部30が設けられている。 - 特許庁
Drive motors 38 and 39 for driving by electric power charged in an electrical storage body 18 are arranged near a brake drum 36 in an outer circumferential surface of an axle case 34.例文帳に追加
アクスルケース34の外周面のうちブレーキドラム36の近傍には、蓄電体18に蓄電された電力によって駆動する駆動モータ38,39が配置されている。 - 特許庁
A pair of chamfered portions 2b are formed continuously in a vertical direction at both ends (outer corner portions) of the end segments of entrance and exit 4 of a shutter case gate 2 in their thickness direction.例文帳に追加
戸袋柵2の乗客出入口4側端部の厚さ方向の両端(外角部)には、一対の面取り部2bが上下方向に連続して形成されている。 - 特許庁
On the outer periphery of a storage case 16 structuring a cone container taking out device, a required heater 15 for heating and drying inside is provided.例文帳に追加
コ−ン容器の取出し装置を構成する収納ケ−ス16の外周に内部を加熱乾燥せしめるべく所要のヒ−タ−15が配設された構成よりなる。 - 特許庁
In this case, it is sufficient for the protecting sheet of paper 31 to have a width corresponding to the outer periphery of the slot 23 and unnecessary to cut the protecting sheet of paper 31 for every one layer of the taking up.例文帳に追加
この場合、保護紙31はスロット23の外周に対応する幅を有していればよく、巻き取りの一層毎に保護紙31をカットする必要もない。 - 特許庁
A openable member is equipped in an outer part along the cover inner face of the case for storing the disaster preventing tool, thereby enabling to form a surface of the stretcher.例文帳に追加
また、担架である防災用具であって、防災用具を納めるケースのカバー内面に沿って外部に展開可能な部材を備えておき、担架の面を形成可能にする。 - 特許庁
Thus, in the case of attaching the ring to the attaching object 12, the pushing operation of the ring R is performed in two stages based on the descent of the inner cylinder 22 and the outer cylinder 20.例文帳に追加
このように、装着対象物12にリングRを装着する際、内筒22と外筒20の降下に基づく二段階でリングRの押込み動作が行われる。 - 特許庁
In the ignition coil, an insulating sheet 4 for mitigating stress is wound on an outer peripheral surface of the center core 23, and a gap in the coil case is filled with the insulating resin.例文帳に追加
点火コイルは、中心コア23の外周面に応力緩和用の絶縁シート4を巻き付け、コイルケース内における間隙を絶縁性樹脂によって充填してなる。 - 特許庁
Further, when the frame is attached to the inside of the outer case and used, a claw plate 2d is attached to one side of the bottom in the frame, thereby preventing the contained pocket tissues from falling.例文帳に追加
さらに、外箱の内面に枠を取り付けて使用するときは、この枠の底の一辺にツメ板2dをつけ、収納されたポケットティッシュの脱落を防ぐようにもした。 - 特許庁
A waterproof packing 11 at the bottom face of the waterproof receptacle is put into a protruding wall 18 formed at an outer periphery of the front opening of the waterproof arrester case 13 to give it a waterproof function.例文帳に追加
防水コンセント底面の防水パッキング11を、防水型アレスタ筐体13の前面開口外周に形成した突出壁18に嵌めて防水機能を持たせる。 - 特許庁
A surface material 37 is attached to the roughly whole surface of the outer surface of the heat insulating case 30, and an air flow passage 50 is formed between the recessed grooves and the surface material 37.例文帳に追加
断熱ケース30の外表面には、略全面にわたって表面材37が貼着され、凹溝と表面材37との間に空気の流通路50が形成される。 - 特許庁
A paper feeding part part is constituted such that a plurality of paper feeding trays 10,... are mounted in an outer case part while they are overlapped and a heater is provided as the dehumidifying means.例文帳に追加
本発明にかかる給紙部は、外函部に複数の給紙トレイ10…を積み重ねた状態で装着しており、さらに除湿手段としてヒータを備えている。 - 特許庁
The magnetic spring mechanism 13 is composed of a magnet 15 provided on an inner peripheral face of the main body case 11 and a magnet 16 provided on an outer peripheral face of a movable shaft 12.例文帳に追加
磁気ばね機構13は、本体ケース11の内周面に設けられたマグネット15と可動軸12の外周面に設けられたマグネット16で構成する。 - 特許庁
First locking parts 10, 10 and a second locking part 11 are formed at an upper and a lower portions on each of inside faces 7b, 9b of a right-side and a left-side walls 7, 9 of the outer case 2, respectively.例文帳に追加
外ケース2の右壁7と左壁9の内側面7b,9b上下には、第1の係止部10,10と第2の係止部11が形成されている。 - 特許庁
The bearing device further comprises a case member 9 having the plurality of displacement sensors 8 detecting the gap thereof from the outer peripheral surface of the inner ring member 3 at predetermined intervals in the peripheral direction.例文帳に追加
内輪部材3の外周面とのギャップを検出する複数の変位センサ8を周方向に所定間隔おきに有するケース部材9が設けられている。 - 特許庁
A cancel cam 40 for pressing a cancel part 42 of a turn signal cancel mechanism according to the return rotation of a steering is projected in the specified position on the outer circumferential surface of the upper case 32.例文帳に追加
アッパーケース32の外周面の所定位置に、ステアリングの戻し回転に伴ってターンシグナルキャンセル機構のキャンセル部42を押圧するキャンセルカム40が突設されている。 - 特許庁
In the case the door outer handle 24 is not operated over the specified position, the door handle switch 26 is opened, and an input high signal is inputted to the vehicle ECU 22.例文帳に追加
一方、ドアアウタハンドル24が所定の位置を越えて操作されない場合、ドアハンドルスイッチ26を開放し、車両ECU22に入力ハイ信号を入力する。 - 特許庁
Its dimensions are set so that relation of W1≤W2 is satisfied in the case that an outer diameter of the cutting edge 7 is W1 and a thread root diameter of the male screw 3 is W2.例文帳に追加
切削刃7の外径寸法をW1とし、雄ねじ3のねじ山の谷径寸法W2としたとき、W1≦W2の関係となるように寸法設定されている。 - 特許庁
An air inlet 7 is vertically and longitudinally bored in a side plate part on each horizontal side of the outer case 1, the air inlet being located at a front portion exposed to the front side of a room wall.例文帳に追加
外ケース1の横方向両側の側板部に、室壁の前方に露出する前側部分に位置させて、空気取入れ口7を上下方向に長手に開設する。 - 特許庁
In another case of operation, An inner diameter _ϕd_2 of the cylindrical delivery chamber is set to half or less of an outer diameter _ϕD of the fixed scroll.例文帳に追加
別実施例では、固定スクロール中心に対して同心となる円筒状の吐出室の内径φd_2 が固定スクロールの外径φDに対して1/2以下に設定している。 - 特許庁
To reliably seal a butted part of an outer flap of a type A corrugated fiberboard case in which front and back sides are difficult to self-stand upright because no inner flap is present by using a packaging tape.例文帳に追加
内フラップがないために前後側面が垂直に自立することが困難なA式ダンボールケースの外フラップの突き合わせ部を包装テープで確実に封緘する。 - 特許庁
Therefore, the contact area of the driving gear in contact with the outer circumferential surface of the fixing roller 500 is a half compared with the case that lots of the convexes 94 and the concaves 96 are not present.例文帳に追加
このため、駆動ギア90が定着ローラ50の外周面に接触する接触面積は、多数の凸94と凹96が無い場合に比べて約2分の1となる。 - 特許庁
The outer case 6 is furnished with a first through hole 10 to admit insertion of each pin 2c of the CPU 2 in such an arrangement as necked in the rear part and shaped as a wedge viewed on the plan.例文帳に追加
外部ケース6には、CPU2のピン2cが挿入され後方部分が狭められて平面視でくさび状に形成された第1貫通孔10が設けられている。 - 特許庁
The foreign matter left on the inner surface of the case 1 is scraped by cleaning screws 13 and 14 attached to the outer circumferential surface of the rotary shaft body 11 and inserted after the cleaning brush 12.例文帳に追加
クリーニングブラシ12より後から挿入する回転軸体11の外周面に取付けたクリーニングスクリュー13,14により、地震計設置ケース1の内面に取残した異物を掻取る。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|