Compressorを含む例文一覧と使い方
該当件数 : 22706件
A first blower 33a is cooperatively operated with ON-OFF control of a compressor 31, a second blower 33b is operated continuously, the compressor 31 being operated is cooled by the first blower 33a is cooled and evaporation of drain water on an evaporation pan 34 is promoted by the second blower 33b.例文帳に追加
第1送風機33aを圧縮機31のON・OFF制御に連動させると共に、第2送風機33bを連続運転させ、第1送風機33aによって作動中の圧縮機31の冷却を行わせ、第2送風機33bによって蒸発皿34上のドレン水の蒸発を促進させる。 - 特許庁
To provide an enclosed compressor which, while ensuring a discharge valve damping function, lowers the power consumption of the compressor by lowering the pressure within a cylinder at the start of discharge, and prevents an oil film-derived delay of a discharge valve upon the completion of discharge to increase a coolant circulation amount and thus to improve a compression capability.例文帳に追加
密閉形圧縮機において、吐出弁を制振する機能を確保しつつ、吐出開始時のシリンダ内圧力を下げて圧縮機の消費電力の低減を図ると共に、吐出完了時の吐出弁の油膜による遅れを防止して冷媒循環量を増加させ圧縮能力の向上を図ること。 - 特許庁
A vertical interval is provided between a connection end of a compressor 110 side and a connection end of an expander 120 side, and by transporting excessive oil in the connected compressor sealing container of an upper end 161 into the connected expander sealing container of a lower end 162, proper lubricating oil management is carried out.例文帳に追加
圧縮機110側の接続端部と膨張機120側の接続端部に高低差を設け、上方端部161の接続された圧縮機密閉容器内の過剰になった潤滑油を、下方端部162の接続された膨張機密閉容器内へ輸送することにより、適切な潤滑油量管理を行う。 - 特許庁
To provide a scroll compressor improving sealing performance of a mating surface of a main frame and a fixed scroll by providing a gap between an outer circumference of the fixed scroll and an inner wall of an enclosed shell and storing lubricating oil in the gap, reducing leak of gas from a high pressure side to a low pressure side, and preventing compressor performance drop.例文帳に追加
固定スクロールの外周と密閉シェルの内壁との間に隙間を設け、この隙間に潤滑油を溜め、メインフレームと固定スクロールの合わせ面のシール性を向上させ、高圧側から低圧側へのガスのリークを低減し、圧縮機の性能低下を防止できるスクロール圧縮機を提供する。 - 特許庁
The air compression apparatus is an air supply source for a pneumatic tool such as a driving machine and is structured so that the air tanks 7 and 13 are installed for the air passages whereby the air compressed by a compressor 4 is separated into two and that the pressure reducing valves 6 and 12 are installed between the compressor 4 and the air tanks 7 and 13.例文帳に追加
打込機などの空気式工具の空気供給源であって、圧縮機4を用いて圧縮した空気を2つに分離した空気流路ごとに夫々エアタンク7、13を設け、前記圧縮機4と前記エアタンク7、13間にそれぞれ減圧弁6、12を設けたことを特徴とする。 - 特許庁
Thus, since the refrigerant pressure to be sucked to a compressor 100 can be lowered as compared with the case of pressure reducing by the ejector 400 at the time of the heating operation, the temperature of the refrigerant to be discharged from the compressor 100 can be raised, and the sufficient heating temperature can be assured even at the time of the heating operation.例文帳に追加
これにより、暖房運転時において、圧縮機100に吸入される冷媒圧力を、エジェクタ400にて減圧させる場合に比べて下げることができるので、圧縮機100から吐出される冷媒の温度を上昇させることができ、暖房時にも十分な暖房温度を確保することができる。 - 特許庁
When executing the defrosting mode of the outdoor heat exchanger 8 while executing heating operation, a control part 65 opens the bypass valve 15 and supplies a high-temperature and high-pressure gas-like refrigerant compressed by the compressor 4 from a discharge port 4p of the compressor 4 to the outdoor heat exchanger 8 through the bypass passage 14 to defrost the outdoor heat exchanger 8.例文帳に追加
暖房運転を実行させつつ室外熱交換器8の除霜モードを実行させるとき、制御部65は、バイパス弁15を開放させ、コンプレッサ4で圧縮された高温高圧のガス状の冷媒をコンプレッサ4の吐出ポート4pからパイパス通路を介して室外熱交換器8に供給して除霜させる。 - 特許庁
The method further includes mixing a fuel (18) with the second compressed working fluid (38) in a reformer (40) to produce the reformed fuel (42), flowing the reformed fuel through a second turbine (44) to cool the reformed fuel, and connecting the second turbine (44) to the second compressor (36) so that the second turbine drives the second compressor (36).例文帳に追加
改質器(40)で燃料(18)を第2の加圧作動流体(38)と混合して改質燃料(42)を生成し、その改質燃料を第2のタービン(44)に流して改質燃料を冷却し、第2のタービン(44)を第2の圧縮機(36)に接続して第2の圧縮機(36)を駆動する。 - 特許庁
To solve the problem of the prior art dehumidifier/dryer that when the temperature in the drying chamber is raised in order to dry a matter quickly, the pressure and temperature in a condenser increase to block operation of a compressor and when the compressor is operated under protected state, the drying time is prolonged significantly.例文帳に追加
従来の構成のものは、乾燥庫内の温度をあげて被乾燥物の乾燥を速めようとすると、凝縮器内の冷媒圧力および温度が上昇して圧縮機が運転出来なくなるものであり、圧縮機を保護した状態で運転すると、乾燥時間が著しく長くなるという課題を有している。 - 特許庁
To increase the amount of refrigerant capable of being supplied from a refrigerant adjustment tank 35 to a compressor 30, and to improve performance for adjusting balance between the amount of refrigerant passing through the compressor 30 and the amount of refrigerant passing through the expander 31, in a refrigerating device 20 comprising a refrigerant circuit 10 provided with the expander 31 for recovering power.例文帳に追加
動力回収用の膨張機(31)が設けられた冷媒回路(10)を備える冷凍装置(20)において、冷媒調整タンク(35)から圧縮機(30)へ供給可能な冷媒量を増加させ、圧縮機(30)の通過冷媒量と膨張機(31)の通過冷媒量とのバランスを調節する能力を向上させる。 - 特許庁
A control valve CV detects a pressure difference ΔP(t) between two pressure monitoring points P1, P2 set in the coolant circulation circuit as an index to presume the coolant discharge capacity of variable displacement compressor CM, and controls the discharge capacity of the compressor by a feedback so that the pressure difference between those two points comes close to a set pressure difference.例文帳に追加
制御弁CVは、容量可変型圧縮機CMの冷媒吐出容量を推し量る指標として冷媒循環回路に設定された二つの圧力監視点P1,P2間の差圧ΔP(t)を検出し、その二点間差圧が設定差圧に近づくように圧縮機の吐出容量をフィードバック制御する。 - 特許庁
A first refrigerating cycle controller 46A determines whether the operation of the refrigerating cycle apparatus 13 should be continued or not based on operation state information which is obtained while a drive motor 59 associated with the compressor 19 is operated in a trial mode and associated with the operation state of the compressor 19 or the refrigerating cycle apparatus 13.例文帳に追加
第1の冷凍サイクル制御装置46Aは、圧縮機19に係る駆動モータ59を試しモードで運転中に取得した、圧縮機19または冷凍サイクル装置13の運転状態に係る運転状態情報に基づいて、冷凍サイクル装置13の運転継続可否を判定する。 - 特許庁
Here, an indoor control portion 12 transmits the temperature difference between an indoor temperature from an indoor temperature sensor 8 and a set temperature from a remote controller 18 to the outdoor control portion 13, and the outdoor control portion 13 decides a compressor operation rotational frequency on the basis of the temperature difference, and controls the rotational frequency of the compressor 1 through an invertor circuit 17.例文帳に追加
この時、室内制御部12は室内温度センサ8からの室内温度とリモコン18からの設定温度との温度差を室外制御部13へ送り、室外制御部13は温度差から圧縮機運転回転数を決定してインバーター回路17を介して圧縮機1の回転数を制御する。 - 特許庁
The one chip microcomputer 10 has a starting register 18 starting a test operation and a built-in self test starting pattern generator 19 setting initial values in test control circuits (a pseudo random number generator 14, a logic circuit inspection compressor 15, a pattern generator 16 and a memory inspection compressor 17) for a built-in self test function.例文帳に追加
1チップマイクロコンピュータ10は、組み込み自己検査機能のために、テスト動作を起動する起動レジスタ18と、テスト制御回路(疑似乱数発生器14、論理回路検査用圧縮器15、パターン発生器16、メモリ検査用圧縮器17)に初期値を設定する組み込み自己検査起動パターン発生器19とを備えている。 - 特許庁
A baseplate 5, a power semiconductor module 6, a smoothing capacitor 7, a bus bar assembly 8 and a printed circuit board 9 are integrally formed in advance as an inverter assembly, and are installed in the motor-driven compressor of the inverter circuit part by fastening the baseplate 5 of this inverter assembly to the housing outer peripheral surface 31 of the motor-driven compressor.例文帳に追加
ベースプレート5とパワー半導体モジュール6と平滑コンデンサ7とバスバーアセンブリ8とプリント基板9とを予めインバータアセンブリとして一体形成しておき、このインバータアセンブリのベースプレート5を電動コンプレッサのハウジング外周面31に締結することにより、インバータ回路部の電動コンプレッサへの組み付けを行う。 - 特許庁
This apparatus is characterized by having a vehicle 11 capable of self-traveling on a soft ground with an engine 12, an air compressor 15 which is driven with a rotation power taken out from the engine 12, and an air injection means 18 for injecting the air compressed with the air compressor 15 into the soil of the soft ground.例文帳に追加
エンジン12によって軟弱地盤上を自力走行可能な乗り物11と、エンジン12より取り出される回転動力によって駆動される空気圧縮手段15と、空気圧縮手段15により圧縮された空気を軟弱地盤の土中に注入する空気注入手段18とを備えている。 - 特許庁
To provide the inlet valve assembly of a reciprocating compressor which improves reliability of the compressor by enabling opening or closing movement of the inlet valve through rotation and linear reciprocating motion, and preventing excessive opening of the inlet valve and breakage of the inlet valve caused by fatigue.例文帳に追加
回動及び直線往復運動により吸入弁が開閉動作を行うようにし、吸入弁が過度に開くことを防止して、吸入弁が疲労により破損されることを防止することで、圧縮機の信頼性を向上し得る往復動式圧縮機の吸入弁アセンブリを提供すること。 - 特許庁
If a component element such as a cooler constituting a refrigeration cycle, or a line interconnecting such component elements bores, depending on the place, in an operation of a compressor, a refrigerant may leak and air may enter the refrigeration cycle from the damaged place to fluctuate a load on the compressor to a large extent.例文帳に追加
冷凍サイクルを構成する冷却器などの構成要素或いはその構成要素間を接続する管路に孔が明くと、その場所によって異なるが、圧縮機の運転中に損傷箇所から冷媒が漏れ出たり、冷凍サイクル内に空気が進入したりし、これにより、圧縮機の負荷が大きく変動する。 - 特許庁
Before supplying electric power to the compressor 10, an amount of a refrigerant supplied to the compressor 10 is suppressed by a suction regulation valve 20, and solenoid valves 18, 19 are opened to bypass other banks 10-1, 10-3 such that the suction side and the discharge side are connected by only a bank 10-2.例文帳に追加
圧縮機10に電力を供給する前に、圧縮機10に供給される冷媒の量を吸入調整バルブ20によって抑制し、バンク10−2のみによって吸入側と吐出側とが接続されるように、ソレノイドバルブ18,19を開いて他のバンク10−1,10−3をバイパスする。 - 特許庁
To provide a compressor of high efficiency and reliability making reduction capable of a sliding loss without causing surface damage of abrasion or the like by direct contact in a journal bearing part of the compressor even by using an HFCs refrigerant or a natural refrigerant containing no chlorine with a poor abrasion resistance characteristic.例文帳に追加
塩素を含まず耐摩耗特性の乏しいHFCs冷媒あるいは自然冷媒などを用いても、圧縮機のジャーナル軸受部での直接接触による摩耗などの表面損傷を起こすことなく摺動損失を低減させることが可能となり、効率および信頼性が高い圧縮機を提供する。 - 特許庁
First the first compressor 5 and second compressor 7 are operated in parallel with each other so that a total pressure ratio is reduced (namely, aerodynamic mismatch is lowered) so as to suppress a propagating stall, and then the first and second compressors 5 and 7 are coupled in series to each other so as to realize a two-stage compression system.例文帳に追加
先ず、第1圧縮機5と第2圧縮機7とをトータルとしての圧力比が低くなる(即ち空力的ミスマッチが小さくなる)並列運転することによって旋回失速を抑制し、その後、それら第1圧縮機5と第2圧縮機7とを直列に繋いで2段圧縮システムを実現している。 - 特許庁
This air conditioner comprises a refrigerating cycle constituted of a compressor, an indoor heat exchanger, a throttle device and an outdoor heat exchanger connected by refrigerant pipes, and a control device for controlling rotational frequency of the compressor according to indoor temperature or indoor humidity, and indoor set temperature or indoor set humidity.例文帳に追加
空気調和機は、圧縮機、室内熱交換器、絞り装置及び室外熱交換器を冷媒配管で接続してなる冷凍サイクルと、運転時に室内温度または室内湿度と室内設定温度または室内設定湿度とに応じて圧縮機の回転数を制御する制御装置とを備える。 - 特許庁
Since a drive motor 3 can be fed with power generated from the fuel cell 1 without operating the compressor 8 when starting the vehicle, operational sound of the compressor 8 especially problematic as the cause of noise is reduced when starting the vehicle thus realizing enhancement of silence.例文帳に追加
これにより、車両発進時に圧縮機8を作動させることなく燃料電池1から発電電力を得て駆動モータ3への電力供給を行うことができ、特に騒音の原因として問題となる車両発進時における圧縮機8の動作音を低減させて、静粛性の向上を実現できる。 - 特許庁
The abnormality determining device determines that the abnormality is caused in any of the members constituting the air flowmeter and the intake passage, when determining that an absolute value of a value corresponding to a difference between an actually measured compressor passing gas flow rate and the estimated compressor passing gas flow rate, is larger than an abnormality determining threshold value by the air flowmeter 51.例文帳に追加
異常判定装置は、エアフローメータ51により実際に測定されたコンプレッサ通過ガス流量と前記推定されたコンプレッサ通過ガス流量との差に応じた値の絶対値が異常判定閾値より大きいと判定したとき、エアフローメータ及び吸気通路を構成する部材の何れかに異常が発生したと判定する。 - 特許庁
The device is provided with the compressor 8 for sucking the fuel gas existing in the prescribed portion P to feed it forcibly to the other portion Q in the buried gas pipe 18, and the driving means 10 for driving the compressor 8, and the driving means 10 is operated using the fuel gas provided in a transfer-filling working site.例文帳に追加
このガス移充填装置は、所定部位Pの燃料用ガスを吸い込んでガス埋設管18の他の部位Qに圧送するためのコンプレッサ8と、コンプレッサ8を駆動するための駆動手段10とを備え、駆動手段10は、移充填作業現場で得られる燃料用ガスを用いて運転される。 - 特許庁
To provide a shaft sealing oil recovery device which makes a refrigerating machine which uses a shaft sealing device for connecting a driving machine to a compressor and hygroscopic lubricating oil to be operated stably by recovering the lubricating oil leaking out of a mechanical seal incorporated in the shaft sealing device and returning the recovered oil to the oil tank of the compressor after deaeration.例文帳に追加
駆動機と圧縮機を軸封装置により接続する吸湿性のある潤滑油を使用する冷凍機において、軸封装置内メカニカルシ−ルより漏れ出た潤滑油を回収し、脱気した後圧縮機油タンクに戻すことで安定した冷凍機運転ができる軸封用油回収装置を提供すること。 - 特許庁
When a battery 50 is shut off from the bus line 54 of the inverters 41, 42, 90, if the voltage of the capacitor 57 becomes lower than a lower limit voltage, a power output device stops a compressor 92 for an airconditioner, and if the voltage of the capacitor 57 becomes higher than an upper limit voltage, the device forcibly drives the compressor 92.例文帳に追加
インバータ41,42,90の電力母線54からバッテリ50が遮断されたとき、コンデンサ57の電圧が下限電圧より低くなったときにはエアコン用コンプレッサ92を停止し、コンデンサ57の電圧が上限電圧より高くなったときにはエアコン用コンプレッサ92を強制的に駆動する。 - 特許庁
The waste heat recovery device including the turbine 1 driven by exhaust gas and the compressor 8 for compressing gas includes: a generator 2 which generates electric power by rotation of the turbine 1; an electric motor 7 which rotationally drives the compressor 8; and a control device for driving the electric motor 7 with the electric power generation output of the generator 2 as the power source.例文帳に追加
排気により駆動されるタービン1、気体を圧縮するコンプレッサ8とを備える排熱回収装置であって、タービン1の回転によって発電する発電機2と、コンプレッサ8を回転駆動する電動機7と、発電機2の発電出力を動力源として電動機7を駆動する制御装置を備える。 - 特許庁
A second steam duct 21 bypassing the rotary compressor 18 is disposed between the first container 1 and the second container 2, and a centrifugal compressor 22 compressing the steam generated in the first container toward the second container, and an opening/closing valve 23 are disposed in series in the second steam duct.例文帳に追加
前記第1容器1内と前記第2容器2内の間に,前記回転型圧縮機18をバイパスする第2の蒸気ダクト21を設け,この第2の蒸気ダクト中に,前記第1容器内で発生する蒸気を前記第2容器に向かって圧縮する遠心式圧縮機22と開閉弁23を直列に設ける。 - 特許庁
Compressed air discharged from a screw compressor 10 and including moisture is supplied to a first gas-liquid separation tank 20, the moisture of the compressed air is deposited by the first gas-liquid separation tank 20 and stored as first drain water, and the first drain water is returned to the screw compressor 10 through a water cooler 50.例文帳に追加
スクリューコンプレッサ10から吐出された水分を含む圧縮空気が第1の気液分離タンク20に供給され、第1の気液分離タンク20により圧縮空気の水分が析出されて第1ドレン水として貯蓄され、第1ドレン水が水クーラ50を介してスクリューコンプレッサ10に還流される。 - 特許庁
To prevent reduction of reliability of a compressor due to breakage of a rotation stopping mechanism composed of a universal joint by load in the radial direction acting on it when the rotation stopping mechanism and a central shaft which does not rotate are provided in a central part of a swing swash plate to miniaturize the swing swash plate type variable displacement compressor.例文帳に追加
揺動斜板型可変容量圧縮機を小型化するために、揺動斜板の中心部に回り止め機構と回転しない中心軸を設けた場合に、自在継ぎ手からなる回り止め機構がそれに作用する半径方向の荷重によって破損して圧縮機の信頼性が低下するのを防止する。 - 特許庁
A bypass steam passage 22 bypassing the steam compressor is formed in the steam duct 19, an opening and closing valve 23 is disposed in the bypass steam passage, and an operation of the steam compressor is stopped, and the opening and closing valve is opened when the temperature at the condenser side becomes lower than the temperature at the evaporator side.例文帳に追加
前記蒸気ダクト19に,前記蒸気圧縮機を迂回するバイパス蒸気通路22を設けて,このバイパス蒸気通路に開閉弁23を設け,前記凝縮器側の温度が前記蒸発器側の温度よりも低くなったとき,前記蒸気圧縮機の運転を停止する一方,前記開閉弁を開くように構成する。 - 特許庁
While the compressor is in operation, temperature redetection in each storage compartment redetermines whether each storage compartment needs cooling or not, and needed or unneeded cooling thus determined triggers selective opening or closing of the valve of the storage compartment, so that the number of operations of the compressor is reduced to suppress power consumption.例文帳に追加
このように圧縮機が稼働中は各貯蔵室の温度検出をもう一度施して各貯蔵室の冷却要否を再度判別し、判別された冷却の要否により該当貯蔵室のバルブを選別的に開閉することにより圧縮機の稼働回数を減らすことで電力消費を抑える。 - 特許庁
To provide a refrigeration cycle device using a CO2 refrigerant, and performing the operation of high efficiency while solving a problem on the lowering of the efficiency in the entire refrigeration cycle device, caused by the lowering of the efficiency of a compressor, even when an opening of a compressor is controlled to maximize a theory COP.例文帳に追加
CO2冷媒を使用した冷凍サイクル装置において、圧縮機の効率が低下するため、理論COPが最大となるように減圧器の開度を制御しても、冷凍サイクル装置全体の効率は低下してしまうという課題を回避しつつ、高効率な運転が可能な冷凍サイクル装置を提供する。 - 特許庁
The geothermal power-generation system includes:a compressor 11 that compresses air; a heating device 14 that heats compressed air compressed by the compressor 11 by geothermal heat; a turbine 12 that obtains a rotational force by heated compressed air heated by the heating device 14; and a generator 13 that generates power by the rotational force inputted from the turbine 12.例文帳に追加
空気を圧縮する圧縮機11と、圧縮機11で圧縮された圧縮空気を地熱により加熱する加熱装置14と、加熱装置14により加熱された加熱圧縮空気により回転力を得るタービン12と、タービン12から回転力が入力されることで発電する発電機13とを設ける。 - 特許庁
The refrigeration unit is provided with a head component 11A inside a compressor which does not incur the contamination or sludge over the long term use as the component of the refrigeration unit, wherein the rust preventive oil in the head component 11A inside the compressor 11 which is degradation attractant is replaced by alkyl benzene series oil which is refrigerating machine oil.例文帳に追加
この冷凍装置では、圧縮機11内部のヘッド部品11A中の劣化誘引物質としての防錆油を冷凍機油としてのアルキルベンゼン系油に置換して、冷凍機の構成部品として長期使用してもコンタミネーションやスラッジを招かない圧縮機内部のヘッド部品11Aを備えた。 - 特許庁
In this rotary compressor assembly, the geometric center between a plurality of support ports 31a, 31b, 31c, formed in a strut 30 so as to provide a vibration isolating member 40, and the total unit center of gravity G of the rotary compressor 10 and an accumulator 20 are substantially equally arranged.例文帳に追加
本発明に係る回転圧縮機組立体によれば、防振部材40が設けられるように突っ張り30に形成された複数の支持口31a,31b,31c間の幾何学的中心と回転圧縮機10及びアキュムレータ20の全体重心Gとが実質的に同一に配されている。 - 特許庁
The scroll compressor includes a first relief valve mechanism that is provided at a lower part of a relief port of a guide frame communicated with an intake port so as to flow out an open liquid coolant by the own weight of a liquid coolant having intruded into the compression mechanism part when the scroll compressor is stopped.例文帳に追加
この発明に係るスクロール圧縮機は、吸入ポートに連通するガイドフレームのリリーフポートの下端部に設けられ、スクロール圧縮機の停止時に圧縮機構部に侵入した液冷媒の自重により開き液冷媒を密閉容器空間に流出させる第1のリリーフバルブ機構を備えたことを特徴とする。 - 特許庁
To provide a scroll compressor capable of reducing a sliding loss, and having high efficiency and reliability without causing surface damage such as abrasion by direct contact in a journal bearing part of a compressor even if an HFCs refrigerant or a natural refrigerant including no chlorine and short of an abrasion resistant characteristic is used.例文帳に追加
塩素を含まず耐摩耗特性の乏しいHFCs冷媒あるいは自然冷媒などを用いても、圧縮機のジャーナル軸受部での直接接触による摩耗などの表面損傷を起こすことなく摺動損失を低減させることが可能となり、効率および信頼性が高いスクロール圧縮機を提供する。 - 特許庁
When a degree of opening of an electronic expansion valve 4 becomes 0% and a pressure within the suction side passage of the compressor 2 is apt to become a negative pressure, the specific pressure expansion valve 8 is opened, the refrigerant flows through the bypass passage 9 and it may be adjusted to prevent the pressure in the suction side passage of the compressor 2 from becoming a negative pressure.例文帳に追加
電子膨張弁4の開度が0%となり、圧縮機2の吸い込み側通路内の圧力が負圧になろうとすると、定圧膨張弁8が開き、バイパス通路9を通じて冷媒が流れ、圧縮機2の吸い込み側通路内の圧力が負圧にならないように調節する。 - 特許庁
The rotary compressor (the multiple cylinder rotary compressor) 10 energizing only the first vane 50 to the first roller 46 by the spring 74 serving as the spring member, is provided with a back pressure chamber 72A for applying back pressure to the second vane 52 to be energized to a second roller 48, and the back pressure chamber 72A is formed as a muffler chamber having a predetermined space volume.例文帳に追加
第1のベーン50のみをバネ部材としてのスプリング74により第1のローラ46に付勢するロータリコンプレッサ10(多気筒回転圧縮機)において、第2のベーン52に背圧を印加して第2のローラ48に付勢するための背圧室72Aを備え、この背圧室72Aを、所定の空間容積を有するマフラ室とする。 - 特許庁
To provide a heat pump type water heater capable of preventing abnormal temperature rise and abnormal pressure rise of a compressor even when an operation is continued until the temperature of the water flowing into a water-refrigerant heat exchanger becomes high temperature, securing reliability of the compressor and each of the devices, and performing efficient hot water supply and heating operation.例文帳に追加
水—冷媒熱交換器に流入する水温が高温になるまで運転を継続させても、圧縮機の異常温度上昇および異常圧力上昇を防止し、圧縮機及び各機器の信頼性を確保することができるとともに、効率のよい給湯加熱運転を実現する。 - 特許庁
To provide a gas compressor in which lubricating oil is not taken out of a housing even if inside of the housing is filled with liquid cooling medium containing lubricating oil at non-operational time of a compressing mechanism and pressure difference between an suction port and a discharge port occurs, and an air conditioner for vehicle using the gas compressor.例文帳に追加
圧縮機構の非作動時にハウジング内が潤滑油を含む液状の冷却媒体で満たされ且つ吸入口と吐出口との間に圧力差が生じても前記ハウジングから潤滑油が持ち出されることのない気体圧縮機および該気体圧縮機を用いた車両用空調装置を提供する。 - 特許庁
Since even a temperature of lubricating oil A in a compressor body 2 can be lowered by lowering the temperature of the delivery coolant in the compressor body 2, viscosity of the lubricating oil A is improved, sealing performance of the compressing mechanism 3 can be improved, and performance (volumetric efficiency) of the compressing mechanism 3 can be improved.例文帳に追加
また、圧縮機本体2内の吐出冷媒の温度が低下することにより、圧縮機本体2内の潤滑油Aの温度も低下させることができるので、潤滑油Aの粘性を高めて圧縮機構3のシール性を向上させることができ、圧縮機構3の性能(体積効率)を高めることができる。 - 特許庁
The control data generation section 16 controls the compressor using a constituent device sensor being a sensor provided in the constituent device for detecting a second physical value that is a physical value having a close correlation with the first physical value in place of the compressor sensor when the abnormality is detected by the abnormality detection unit 13.例文帳に追加
制御データ生成部16は、異常検出部13によって異常が検出された場合に、圧縮機用センサに代えて、構成機器に設けられるセンサであって第1物理量と密接な関係を有する物理量である第2物理量を検出する構成機器用センサを用いて、圧縮機を制御する。 - 特許庁
To provide a scroll compressor which is excellent in efficiency and reliability, by reducing a sliding loss without damaging a surface due to abrasion even at inclining of a main shaft in a journal bearing of the compressor, using a HFCs coolant or a natural coolant not including chlorine and having poor abrasion resistance.例文帳に追加
塩素を含まず耐摩耗特性の乏しいHFCs冷媒あるいは自然冷媒などを用いて、圧縮機のジャーナル軸受での主軸の傾斜時にも、摩耗などによる表面損傷を起こすことなく摺動損失を低減させることが可能であり、効率および信頼性の高いスクロール圧縮機を提供する。 - 特許庁
To provide a piston type variable displacement compressor preventing generation of a noise caused by fine repetitive movement of a valve element of an opening regulating valve at fine flow time, in the piston type variable displacement compressor equipped with the opening regulating valve variably controlling an opening area of a flow path between a suction port and a suction chamber.例文帳に追加
吸入ポートと吸入室との間の流路の開口面積を可変制御する開度調整弁を備えるピストン式可変容量圧縮機であって、微小流量時の開度調整弁の弁体の微小反復移動に起因する騒音の発生が防止されたピストン式可変容量圧縮機を提供する。 - 特許庁
To provide a control method of a variable displacement compressor capable of preventing the occurrence of trouble by avoiding generation of a lean lubricating state, by properly returning lubricating oil even when controlled in maximum delivery capacity, in the variable displacement compressor returning the lubricating oil to a crankcase via a capacity control valve.例文帳に追加
容量制御弁を介して潤滑油をクランク室に戻すようにした可変容量型圧縮機において、最大吐出容量に制御されている時にも適切に潤滑油を戻せるようにし、貧潤滑状態の発生を回避して不具合の発生を防止可能な可変容量型圧縮機の制御方法を提供する。 - 特許庁
A compressor operation control temperature when a temperature adjustment lever 7 is positioned in a place where the lever is moved from a MAX-COOL position by a predetermined range (idle area=range of gradual variation area) is varied to a higher temperature relative to a compressor operation control temperature when the temperature adjustment lever 7 is positioned at the MAX-COOL position.例文帳に追加
温度調節レバー7がMAX−COOL位置にあるときの圧縮機稼働制御温度に対して、温度調節レバー7をMAX−COOL位置から所定範囲(アイドル領域=徐変領域の範囲)以上移動させた位置にあるときの圧縮機稼働制御温度をより高い温度に変化させている。 - 特許庁
When the motor 36 for traveling is controlled to be driven in a regenerative mode and the capacitor 32 is nearly fully charged, an air compressor 28 to which a power is supplied via a DC-DC converter 54, is forcibly driven and the regenerative power generated by regeneratively controlling the motor 36 for traveling is consumed in the air compressor 28.例文帳に追加
走行用モータ36が回生モードで駆動制御されると共にキャパシタ32が満充電近傍のときには、DC/DCコンバータ54を介して電力が供給されるエアコンプレッサ28を強制的に駆動して走行用モータ36を回生制御することにより生じる回生電力をエアコンプレッサ28で消費する。 - 特許庁
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|