| 例文 |
off currentの部分一致の例文一覧と使い方
該当件数 : 4098件
When a switching element Q1 is turned off, the current to generate the overshoot is allowed to run in the switching element Q1 by giving a pulse to the control input of the switching element Q1, in response to the timing at which the overshoot is generated in a connection point 15 of the switching element Q1 to a primary coil L1.例文帳に追加
スイッチング素子Q1をターンオフさせたときには、スイッチング素子Q1と一次コイルL1との接続点15にオーバーシュートが生じるタイミングに対応して、スイッチング素子Q1の制御入力にパルスを与えることにより、オーバーシュートを生じさせる電流をスイッチング素子Q1に流す。 - 特許庁
When a gate voltage voltage Vge exceeds the boundary voltage value Vbor, since the 1st switching transistor Tr1 is turned on and the 2nd switching transistor Tr2 is turned off, the base voltage of the gate control transistor Tr3 becomes equal to the voltage drop amount corresponding to those of current detection resistor R1 and R2.例文帳に追加
一方、ゲート電圧Vgeが境界値Vbor を超えたときは、第一切替トランジスタTr1がオンすると共に第二切替トランジスタTr2がオフするため、ゲート制御トランジスタTr3のベース電圧は2つの電流検出抵抗R1,R2による電圧降下分となる。 - 特許庁
Then, when this current value and the power value calculated from the input voltage value of a lamp drive circuit LD come to the set values, reset pulses are outputted from the calculation result output terminal of a constant power arithmetic circuit M, and the flip flop circuit FF is reset, the switching element Q1 is turned off.例文帳に追加
そして、この電流値とランプドライブ回路LDの入力電圧値から演算された電力値が設定値になると、定電力演算回路Mの演算結果出力端子からリセットパルスが出力され、フリップフロップ回路FFがリセットされ、スイッチング素子Q1はオフとなる。 - 特許庁
The sensor S, a diode D and a load resistance R are connected in series to an alternating current source P, and a comparator 5 for switching between ON/OFF states of an output by comparing the voltage amplified by an operational amplifier 6 with a prescribed threshold is connected to both ends of the load resistance R through the operational amplifier 6.例文帳に追加
センサSとダイオードDと負荷抵抗Rを交流電源Pに直列に接続し、負荷抵抗Rの両端にオペアンプ6を介し、このオペアンプ6で増幅された電圧を所定のしきい値と比較して出力のオン、オフを切り換えるコンパレータ5を接続する。 - 特許庁
If a signal Sc1 indicates that the output node potential Vnd is below a first reference potential Vr1, which is used as a reference for detecting the production of an inrush current when the first switch SW1 is on, a control circuit 10 turns the first switch SW1 into an off state.例文帳に追加
制御回路10は第1のスイッチSW1をオンさせている際に、出力ノード電位Vndが突入電流発生を検知するための基準となる第1の基準電位Vr1を下回っていることを信号Sc1が示したときは、第1のスイッチSW1をオフ状態にする。 - 特許庁
In this manufacturing method, in an on-state, a current flows, and in an off-state, at least one of a depleting n drift region 22a and p partition region 22b, for example, the p partition region 22b is formed with ion implantation, in particular, ion implantation in which an accelerating voltage continuously changes.例文帳に追加
オン状態では電流を流すとともに、オフ状態では空乏化するnドリフト領域22a、p仕切り領域22bのうち少なくとも一方、例えばp仕切り領域22bを、イオン注入、特に加速電圧を連続的に変えたイオン注入で形成する。 - 特許庁
While turning power supply to loads 12-14 off and charging a battery 6 with a constant current, battery voltage 6a is measured, while raising precision at a detecting section 16, when the battery voltage is in the vicinity of full charge voltage; and then the measured voltage is recorded in a measurement data storage memory 19 (voltage before the change).例文帳に追加
負荷である12〜14への電源供給をオフにし、電池6に定電流充電を行いつつ、電池電圧が満充電近辺の範囲にある時に、検出部16の精度を上げて電池電圧6aを測定し測定データ記憶メモリ19に記録する(変移前電圧)。 - 特許庁
When the vehicle body speed exceeds a first threshold value, for example, a duty ratio of ON/OFF of a current supplied to respective linear valves SLFR to SLRR is set so as to be a differential pressure amount corresponding to the target W/C pressure obtained in a target W/C pressure calculation part 100a at 1:1 ratio.例文帳に追加
例えば、車体速度が第1しきい値を超えているときには、目標W/C圧演算部100aで求められた目標W/C圧と1:1で対応する差圧量となるように、各リニア弁SLFR〜SLRRに対して流す電流のON/OFFのデューティ比を設定する。 - 特許庁
Fluctuation of the voltage at the power source noise measuring point which is a power source noise generates fluctuation of the voltage between the gate and the source of the MOS transistor, and the ON/OFF state of the MOS transistor or fluctuation of a drain current value generated by the fluctuation is observed, to thereby measure the power source noise.例文帳に追加
電源ノイズである電源ノイズ測定点の電圧の変動が、MOSトランジスタのゲート−ソース間電圧の変動となり、その変動が起こすMOSトランジスタのON/OFF状態もしくはドレイン電流値の変動を観測することで、電源ノイズを測定する。 - 特許庁
Two amplification circuits 31, 32 of the level converting amplification section 30 are connected in parallel with respect to the transistors T3, T4 of the selector circuit section 20, and turn on one of the transistors T3, T4 and turn off the other simultaneously in response to an output of the differential circuit section 10 to switch the bias current Ib.例文帳に追加
レベル変換増幅部30の2つの増幅回路31,32は、セレクタ回路部20のトランジスタT3,T4に対して並列に接続されており、差動回路部10の出力に応じてトランジスタT3,T4の一方をオンし同時に他方をオフすることでバイアス電流Ibを切り換える。 - 特許庁
Then the occurrence of an overcurrent to the IC 1 is monitored by means of a current detecting resistor 4 and an overcurrent detecting circuit 5, and when an overcurrent occurs, the power switch 8 is turned off by means of a switch control section 6 and the gates 9 and 10 are set to the second state by means of a gate control section 11.例文帳に追加
そして、電流検出用抵抗4および過電流検出回路5によりIC1への過電流の発生を監視し、過電流が発生した場合にスイッチ制御部6が電源スイッチ8をOFFするとともに、ゲート制御部11がゲート部9,10を第2状態とする。 - 特許庁
The operating current of the impedance conversion circuit IPC_1 is stopped as well as the partial switch PSW_1 is set into an on-state based on the output of the first masking circuit MASK_1; otherwise, the source line S_1 is driven by the impedance conversion circuit IPC_1 as well as the partial switch PSW_1 is set into an off-state.例文帳に追加
第1のマスク回路MASK_1の出力に基づき、インピーダンス変換回路IPC_1の動作電流を停止すると共にパーシャルスイッチPSW_1をオンに設定し、或いは、インピーダンス変換回路IPC_1がソース線S_1を駆動すると共にパーシャルスイッチPSW_1をオフに設定する。 - 特許庁
To provide a display device which is not configured to suppress OFF-current of a switching transistor and to increase capacitance of a capacitance element but is made resistant to an influence by parasitic capacitance or wiring capacitance, and to provide a driving method therefor, especially a driving method by a dot matrix system.例文帳に追加
スイッチング用トランジスタのオフ電流を低く抑えたり、容量素子の容量を大きくする構成ではなく、寄生容量又は配線容量の影響を受けにくい表示装置、及びその駆動方法、特に面積階調方式による駆動方法を提供することを課題とする。 - 特許庁
To provide a circuit breaker capable of suppressing an excessive temperature rise of a contact part by enhancing the heat radiating characteristic of stationary contact pieces for securing the current feeding capacity of a contact, preventing the stationary contact pieces from contamination caused by carbides produced by the arc heat at the time of shutting off the overcurrent, thereby securing the insulating performance.例文帳に追加
接点の通電容量確保を狙いに固定接触子の放熱性を高めて接点部の過度な温度上昇を抑え、併せて過電流しゃ断時のアーク熱で生成した炭化物による固定接触子の汚損を防いで絶縁性能の確保を図るようにする。 - 特許庁
The additional decrease of the off currents of the TFTs 10 for pixels, the additional increase of the on currents of the TFTs 20 and 30 for driving circuits, the assurance of the on current and gate capacity balances of the TFTs 20 and 30 for driving circuits, etc., are achieved in addition to the effects of the LDD structures.例文帳に追加
LDD構造による効果に加えて、画素用TFT10のオフ電流の一層の低減と、駆動回路用TFT20,30のオン電流の一層の増大、駆動回路用TFT20,30のオン電流やゲート容量バランスの確保などを達成できる。 - 特許庁
To accurately control the magnitude of the output voltage of a transformer, based on the length of the ON period of a MOSFET, in a switching power unit which boosts a voltage more by means of a transformer prior to output, by controlling a current to be supplied to the transformer by the ON-OFF of the MOSFET.例文帳に追加
MOSFETのオン、オフによりトランスに供給する電流を制御して、トランスにより電圧を昇圧して出力するスイッチング電源装置において、MOSFETのオン期間の長さに基いて、トランスの出力電圧の大きさを精度良く制御できるようにする。 - 特許庁
Therefore, the dispersion of the threshold voltages of TFT 40P, 40N can be compensated, and also the floating body effect can be suppressed, and in the operational state, fast and accurate operation is made possible, and in the stand-by state, the power consumption is reduced by lowering the off-current.例文帳に追加
したがって、TFT40P,40Nの閾値電圧のばらつきを補償するとともに、フローティングボディ効果を抑制することができ、前記動作状態では、高速かつ正確な動作が可能になり、前記待機状態では、オフ電流を低くして、消費電力を削減することができる。 - 特許庁
Under a low temperature state where the battery temperature TB is lower than a predetermined temperature #TBL, charging current of a high voltage battery is increased without altering the regenerative operation of a motor or the power generating state by turning off or reducing the output from a DC-DC converter in a regenerative or charging mode.例文帳に追加
バッテリ温度TBが所定温度#TBL未満となる低温状態において、回生または充電モードではDC−DCコンバータの出力をOFFまたは出力を低減させることによって、モータの回生動作や発電の状態は変更せずに高圧バッテリの充電電流を増大させる。 - 特許庁
To provide an image forming apparatus capable of suppressing wear of a photoreceptor drum, while surely preventing a white-dot image from being produced, by controlling the value of the current flowing to a charging member in specified timing, regardless of whether a main switch of the image forming apparatus is on or off.例文帳に追加
画像形成装置のメインスイッチのオン・オフに関わりなく、帯電部材に流れる電流値を所定のタイミングで制御することによって、白点画像の発生を確実に防止しつつ、感光体ドラム表面の磨耗を抑制することが可能な画像形成装置を提供することを課題とする。 - 特許庁
In the method for measuring the resistance of the coating film, which is covered with a cover material, by a fall-of-potential method, an interruptor turned ON/OFF by an M system code pattern is installed on a current-carrying cable and the obtained potential difference is subjected to cross-correlation processing.例文帳に追加
上記課題は、被覆材に被覆された塗膜抵抗を電位降下法で測定する方法において、通電ケーブルにM系列符号パターンによりオン/オフするインタラプタを設置し、得られた電位差を相互相関処理することを特徴とする塗膜抵抗の測定方法によって解決される。 - 特許庁
When the second contact 4 lying at the on-position is relatively separated from the first contact, the second contact 4 is connected to the first contact 3 through the resistor 6, and when the second contact 4 is moved at the off-position, the second contact 4 shuts down the current while making the first contact not contact with the resistor 6.例文帳に追加
オン位置にある第2接点4と第1接点3とが相対的に離れるとき、第2接点4が抵抗体6を介して第1接点3に接続され、第2接点4がオフ位置に移動すると、第1接点3と抵抗体6に接触しないようにして電流を遮断する。 - 特許庁
An image signal, i.e., DATA, is subjected to pixel modulation at a modulating section 78 and a logic element 70 turns a switch 79 on/off by ORing the output signal from the modulating section 78 and a full lighting signal FULL from a sequence controller 77 thus controlling the pulse current of a laser 73A.例文帳に追加
画像信号であるDATAは、変調部78において画素変調され、その出力信号とシーケンスコントローラ77からのフル点灯信号FULLのORを出力する論理素子70によりON/OFFするスイッチ79によって、レーザ73Aのパルス電流は制御される。 - 特許庁
Thus, the output of a NAND gate G1 in which the output of the D flip-flop FF1 and a transmitting signal are inputted turns a transistor M2 ON so as to stop the operation of the current mirror circuit and turns a transistor M1 OFF so that interruption between the power supply circuit PS1 and a power supply line is performed.例文帳に追加
これにより、その出力と送信信号とが入力されるNANDゲートG1の出力が、カレントミラー回路の動作を停止させるようにトランジスタM2をONさせると共に、電源回路PS1と電源ラインとの間が遮断されるようにトランジスタM1をOFFさせる。 - 特許庁
In this state, a switching circuit 16 is intermittently switched on - off by an output of an oscillating circuit 21, and accordingly power is intermittently supplied to the first and second voltage- dividing circuits 11 and 12, and thereby an average current consumption in these voltage-dividing circuits 11 and 12 is controlled.例文帳に追加
この状態では、スイッチング回路16が発振回路21の出力により間欠的にオンオフされて、第1及び第2の分圧回路11及び12に対する電圧供給が間欠的に行われるため、それら分圧回路11及び12での平均消費電流が抑制されることになる。 - 特許庁
Furthermore, even after the semiconductor breaker 12 breaks the current, an electrical connection state of the semiconductor breaker 12 is temporarily switched from off to on so as to discharge electric charges charged in a capacitor 14, thereby there is no problem even if capacitance of the capacitor 14 is small.例文帳に追加
また、半導体遮断器12にて電と流を遮断した後も、半導体遮断器12の電気的接続状態をオフ状態から一時的にオン状態に切り替えて、コンデンサ14に充電された電荷を放電させるようにして、コンデンサ14の容量が小さくてもすむようにしている。 - 特許庁
The commutation sequence selection part includes a commutation means for transiting a switching state at a timing of switching between on/off states in a serial-connected switching element, so that current commutates when voltage switches from/to a range between 0 and -E to/from a range between 0 and +E in output voltage level.例文帳に追加
転流シーケンス選択部は、直列接続されたスイッチング素子のオン・オフ状態変化時にスイッチング状態を遷移させる転流手段を備え、出力電圧レベルが0と−E相互間及び0と+E相互間での電圧切り替わり時に転流するようにしたものである。 - 特許庁
When the LED 20 is lighted, the value of the voltage V2 is maintained high with a shorter put-off time, and the amperage I_2 lessens at starting the lighting to cause a large current to be supplied to the LED 20, which enables maintaining the photo-quantity of the LED 20 constant.例文帳に追加
また、LED20の点灯時においては、消灯時間が短いほど、電圧V2の電圧が高い値に維持され、点灯開始時における電流I_2の値が小さくなり、LED20には大きな電流が供給され、LED20の光量を一定に維持することができる。 - 特許庁
By bringing the four MOS transistors 61a-61d into the off-state before the predetermined period elapses since the DC-DC converter 4 starts to operate like this, an oscillating condition that a grounding current intermittently flows is not caused, so that the earth fault can surely be detected.例文帳に追加
このように、DC−DCコンバータ4が作動開始した時点から所定時間経過前においては、4つのMOSトランジスタ61a〜61dをオフ状態にすることによって、地絡電流が間欠的に流れる発振状態になることはなく、確実に地絡を検出することができる。 - 特許庁
In cutting off arcs generated between the contacts of the breaker with weak input current running if the breaker is opened, this method exerts control so as to open between the contacts of the breaker, close a switch, and close a charging resistor shortening switch.例文帳に追加
遮断器を開放動作をした時に流れる微少な入力電流によって遮断器の接点間に発生するアークを遮断する場合、まず遮断器の接点間を開放すると共に前記スイッチを閉じ、次に充電抵抗器短絡用スイッチを閉じるよう制御した方法である。 - 特許庁
A thermosensible sensor is arranged or built in the electric outlets, and when an electric outlet body rises to an abnormal temperature, the sensor operates, and sends a signal to an earth leakage breaker built in the electric outlet or the earth leakage breaker in an existing distribution board, and cuts off a supply current by operating the breaker.例文帳に追加
コンセント類に感熱センサーを設置または内蔵させ、コンセント本体が異常な温度に上昇した時、センサーが働いて信号をコンセントに内蔵された漏電遮断器又は既設分電盤内の漏電遮断器に送り、それを動作させて供給電流を遮断する。 - 特許庁
The blocking diode prevents a current running from the floating inductance component of a high-potential side switching semiconductor device 102 from running from the first drive circuit side to the second drive circuit side in the level shift circuit, when the high-potential side switching semiconductor device 102 is turned off.例文帳に追加
阻止ダイオードは、高電位側スイッチング半導体素子102等がターンオフした時、高電位側スイッチング半導体素子の浮遊インダクタンス成分等から流れ出る電流が、レベルシフト回路内で第1駆動回路側部分から第2駆動回路側部分へ流れるのを阻止する。 - 特許庁
A depletion layer is expanded from the floating-current blocking region 8 towards the n-type GaN layer 6 on turning off the semiconductor device, a potential is lowered in the n-type GaN layer 26 filled in the aperture 28, and the voltage is decreased across the front side and the back side of a gate-insulating film 20.例文帳に追加
半導体装置のオフ時に、浮遊電流ブロック領域8からn型のGaN層6に向かって空乏層が広がり、アパーチャー28を充填しているn型のGaN層26の電位が低下し、ゲート絶縁膜20の表面と裏面の間にかかる電位差が減少する。 - 特許庁
This device is provided with various means, such as current required for temperature detection, time intervals of detection, automatic off of the temperature display with an elapsed time, the restart of the temperature display by input means and diversification of display for the purpose of decreasing power consumption of the back up power source 8 and the convenience.例文帳に追加
バックアップ電源8の消費電力の低減と利便性のために、温度検知に要する電流、検知の時間間隔、経過時間による温度表示の自動オフ、入力手段による温度表示の再開、表示の多様化など種々の手段を設けている。 - 特許庁
Then while the switches SW1 and SW3 are turned OFF, the SW2 is turned ON and the voltage of a capacitor C1 on the side of a switch SW4 is varied according to a signal voltage and added to the gate of the driving transistor T1, thereby making a current corresponding to the signal voltage flow to the driving transistor T1.例文帳に追加
そして、スイッチSW1,SW3をオフして、SW2をオンすると共に、容量C1のスイッチSW4側の電圧を信号電圧に応じて変動させることで、その電圧を駆動トランジスタT1のゲートに加算し、信号電圧に応じた電流を駆動トランジスタT1に流す。 - 特許庁
When the other end of each finger 4 is closed by a certain angle prescribed, the current to the servo motor 3 with brake is shut off to stop the servo motor 3, and brake is applied while it is pushed by a spring, out of illustration, and thereafter an air cylinder 22 is actuated so that the other ends of the fingers 4 lock the workpiece 41.例文帳に追加
各フィンガー4の他端が所定の角度だけ閉じられたとき、ブレーキ付きサーボモータ3への電流が切られ、ブレーキ付きサーボモータ3を停止し、図示しないスプリングに押されブレーキが掛けられ、その後で、エアシリンダ22を作動して各フィンガー4の他端がワーク41をロックするようにした。 - 特許庁
After the lapse of the retract delay time Td from the OFF of the device power source, switch circuits 24 and 25 are turned on by a retract driving circuit 23, the retract capacitor Cr charged with the boost voltage Vup is discharged, a discharging current is supplied to a voice coil 5a and a head assembly is retracted.例文帳に追加
そして、装置電源がOFFしてからリトラクト遅延時間Tdを経過すると、リトラクト駆動回路23によりスイッチ回路24,25をONさせ、昇圧電圧Vupで充電されているリトラクトコンデンサCrを放電させ、放電電流をボイスコイル5aに供給し、ヘッドアセンブリをリトラクトさせる。 - 特許庁
As a result, since the current outputted from the switching elements Q11 to Q14 at the timing of turning-off flows via the parallel resistors R11//R12, a power load can be shared to the first resistor R11 and the second resistor R12, thus obviating the necessity for imparting a large-lower specification to the first resistor R11.例文帳に追加
そのため、ターンオフ時にスイッチング素子Q11〜14から出力される電流は、並列抵抗R11//R12を介して流れるので、第1の抵抗R11、第2の抵抗R12に電力負担を分担することができ、これにより第1の抵抗R11を大電力仕様のものにする必要が生じない。 - 特許庁
A non-illustrated voltage source or current source is connected to a source of a transistor 9 in a reset circuit 3 and by turning on and off the transistor 9 at the interval of a predetermined term, the chaos generating circuit 2 is reset to desired initial conditions, thereby stabilizing an output of the chaos generating circuit 2.例文帳に追加
リセット回路3のトランジスタ9のソースには、図示しない電圧源又は電流源が接続され、トランジスタ9を所定の周期ごとにオンオフすることによって、カオス生成回路2を所望の初期条件にリセットして、カオス生成回路2の出力を安定化する。 - 特許庁
When the leakage of molten copper cuts a part of metallic bodies formed so as to be planar shape in the detector 7 at the lower part thereof, a measurement apparatus in a control section detects the cutting-off of current flowing through the metallic body and the reduction of voltage, and the control section directs an alarm apparatus to sound an alarm.例文帳に追加
溶銅の漏れが、下方にある検知器7において面状に形成された金属体の一部を切断すると、制御部内の測定装置が金属体に流れる電流の遮断や電圧の低下を検知し、制御部が警報機に警報を鳴らすように指示をする。 - 特許庁
During the initial stage of starting of the discharge lamp, the above switch SW is held in Off state and, after a certain time from the starting or when the voltage, power, current value or the light amount of the discharge lamp have reached a prescribed value, the above switch element SW is closed, and the overshoot inhibiting circuit 4 is made effective.例文帳に追加
放電ランプの始動初期の間、上記スイッチ素子SWはオフ状態に保持され、始動から一定時間後または電圧、電力、電流値または放電ランプの光量が所定値に到達すると上記スイッチ素子SWを閉じ、オーバーシュート抑止回路4を有効にする。 - 特許庁
At high tide, the ocean currents from the Bungo-suido Channel and the Kii-suido Channel flow into the Seto Inland Sea, where they collide off the coast of Tomonoura (located roughly in the center of the Seto Inland Sea); at low tide, however, they flow away from each other, with the current from the Kii-suido Channel flowing to the east and that from the Bungo-suido Channel flowing to the west and the coast of Tomonoura serving as a kind of central border. 例文帳に追加
瀬戸内海の海流は満潮時に豊後水道や紀伊水道から瀬戸内海に流れ込み瀬戸内海のほぼ中央に位置する鞆の浦沖でぶつかり、逆に干潮時には鞆の浦沖を境にして東西に分かれて流れ出してゆく。 - Wikipedia日英京都関連文書対訳コーパス
Flow of a charging current through the parasitic diode 202 is stopped, even when the switch circuit 102 is OFF and a charger 104 is connected by detecting connection of the charger 104 and separating a resistor 123 from an overcurrent detecting terminal.例文帳に追加
本発明では充電器104が接続されたことを検出し抵抗123を過電流検出端子からから切り離すことにより、スイッチ回路102がOFFし充電器104が接続されている場合でも寄生ダイオード202を介して充電電流が流れない構成とした。 - 特許庁
The current limiter (4) further comprises a detector (204) which detects waveform of a voltage of a line to be cut off and supplies the information on the voltage waveform to the control system (12), and the control system (12) controls the movement of the operating piece (8) based on the information on the voltage waveform.例文帳に追加
電流遮断器(4)は、遮断されるべきラインの電圧の波形を検出し電圧波形に関する情報を制御システム(12)へ供給する検出器(204) をさらに包含し、制御システム(12)が電圧波形に関する情報にもとづき作動子(8)の運動を制御するようになっている。 - 特許庁
In the ignition coil 100, a diode 55 for regulating a reverse current induced to a secondary coil 65 when energization to the primary coil 60 is changed from an off-state to an on-state, and a secondary copper wire 66 for forming the secondary coil 65 are connected by a connecting member 90.例文帳に追加
この点火コイル100では、一次コイル60への通電をオフ状態からオン状態とした際に二次コイル65に誘導される逆電流を規制するダイオード55と、二次コイル65を形成する二次銅線66とが、接続部材90によって接続されている。 - 特許庁
The position detection processing means 112 conducts position detection processing on the basis of the signal given by the detection timing control means 111, and a theft detecting means 113 detects a theft state on the basis of the comparison of a vehicle position when the ignition key is turned off with the current vehicle position.例文帳に追加
位置検出処理手段112は、検出タイミング制御手段111からの信号に基づいて位置検出処理を行い、盗難検知手段113はイグニッションキーがオフされたときの車両位置と現在の車両位置との比較に基づいて盗難状態を検知する。 - 特許庁
In another aspect, partial array self-refresh operation is performed by controlling row addresses of one or more corresponding to a partial cell array in self-refresh operation, and at this juncture, reduction of current consumption of self-refresh is performed by cutting off activation of a part being not used in a memory bank.例文帳に追加
或いは、部分アレーセルフリフレッシュ動作は、セルフリフレッシュ動作中における部分セルアレーに対応する一つ以上のローアドレスを制御することによって実行され、この際、セルフリフレッシュ電流消費の低減は、メモリバンクの不使用の部分の活性化遮断によってなされる。 - 特許庁
When the flash light 2 is mounted on the holding stand 3 in the state where a main switch 25 of the flash light is turned on and white light emitting diodes 11 are lighted, the white light emitting diodes are turned off, and green light emitting diodes 12 are lighted by the current supplied from an adapter 45 of the holding stand 3.例文帳に追加
懐中電灯2の主スイッチ25をオンして白色発光ダイオード11を点灯した状態で保持台3に装着すると、これらが消灯し、代わって緑色発光ダイオード12が保持台3のアダプタ45から供給される直流電流により点灯する。 - 特許庁
At a healthy commercial power supply time, a high-speed limiting current shut-off unit 3 supplies the power to a load through a dc reactor, and a standby power supply unit 4 performs a PW control so that both the effective power and the reactive power supplied to a load 9 become zero.例文帳に追加
商用電源の健全時には、高速限流遮断部3は商用電源から直流リアクトルを介して負荷に対して電力を供給し、予備電源部4は負荷9に対して供給する有効電力及び無効電力が共に零となるようにPQ制御を行う。 - 特許庁
To provide a power supply control circuit that does not require a control integrated circuit (IC) for power supply control, consumes no current when the power supply control circuit is turned OFF, and actualizes a soft switch function for an power source with an extremely small-scale circuit.例文帳に追加
本発明は、電源制御に制御ICを必要とせず、当該電源制御回路がオフ状態の時は、消費電流をゼロとすることが可能であり、極めて小規模な回路で電源のソフトスイッチ機能を実現することが可能な電源制御回路を提供することを目的とする。 - 特許庁
To provide a new organic semiconductor satisfying both of the high electric field effect mobility required for organic semiconductor materials and the high on/off electric current ratio and excellent in a material system and capable of readily being synthesized and to provide a method for producing the compound and to provide an organic semiconductor device using the compound.例文帳に追加
有機半導体材料に求められている高い電界効果移動度と、高いオン/オフ電流比の双方を満足し、かつ材料系に優れ、合成が容易である新規な有機半導体化合物、その製造方法およびそれを用いた有機半導体デバイスを提供する。 - 特許庁
| 例文 |
| 本サービスで使用している「Wikipedia日英京都関連文書対訳コーパス」はWikipediaの日本語文を独立行政法人情報通信研究機構が英訳したものを、Creative Comons Attribution-Share-Alike License 3.0による利用許諾のもと使用しております。詳細はhttp://creativecommons.org/licenses/by-sa/3.0/ および http://alaginrc.nict.go.jp/WikiCorpus/ をご覧下さい。 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|