| 例文 |
speed differenceの部分一致の例文一覧と使い方
該当件数 : 2023件
In this clutch control device, actual rotation difference absorbing torque calculation means 150 applies a change rate ΔNe of an engine speed during a speed change to an actual rotation difference absorbing torque-ΔNe table 160, to calculate an actual difference absorbing torque average during the speed change.例文帳に追加
実回転差吸収トルク算出手段150は、変速中におけるエンジン回転数の変化率ΔNeを実回転差吸収トルク−ΔNeテーブル160に適用して、変速中の実回転差吸収トルク平均値を算出する。 - 特許庁
Here, when the circumferential speed V is different from a reference circumferential speed Vp, a drive motor 88 is driven based on speed difference between V-Vp.例文帳に追加
ここで、定着ベルト102の周速度Vが、基準周速度Vpと異なる場合、V−Vpの速度差に基づいて、駆動モータ88を駆動する。 - 特許庁
The speed difference between the delivery speed and rolling speed of the film 202 is controlled so that the tension detected by the tension sensor 209 is within a predetermined range.例文帳に追加
そして、テンションセンサ209により検知されるテンションが所定範囲内になるように、フィルム202の送り出し速度と巻取り速度との速度差を制御する。 - 特許庁
The computed average rotational speed and a desired rotational speed (set rotational speed) are compared with each other, and it is determined whether or not the difference between them is excessive or not.例文帳に追加
演算された平均回転速度と希望する回転速度(設定回転速度)とを比較し、両者の差が過大であるか否かを判断する。 - 特許庁
A difference in speed between the peripheral speed of the platen roller and the peripheral speed of the discharge roller is 10% or more, or preferably 20% or more to 50% or less.例文帳に追加
プラテンローラの周速度と排出ローラの周速度の速度差は10%以上、好ましくは20%以上かつ50%以下である。 - 特許庁
To provide an image forming device capable of maintaining a certain speed difference between the transcription belt running speed and the recording sheet transporting speed generated by a resist roller irrespective of a change with time etc. of the resist roller performance.例文帳に追加
レジストローラ性能の経時変化等に拘わらず、転写ベルト走行速度とレジストローラによる記録紙搬送速度との所定速度差を維持する。 - 特許庁
To minimize the speed lowering when there is a speed difference between a scanner (image inputting side) and a printer (image outputting side) and the speed adjustment is needed by using a memory.例文帳に追加
スキャナ(画像入力側)とプリンタ(画像出力側)の速度差があり、メモリを用いて速度調整が必要な場合に速度低下を最低限に抑える。 - 特許庁
Then, the fuel injection amount to the internal-combustion engine is increased or decreased in accordance with the difference between the actual car speed and the target car speed (S7).例文帳に追加
その後、実車速と目標車速との差に応じて、内燃機関への燃料噴射量を増減する(S7)。 - 特許庁
Torque of the motor generator is controlled in accordance with a difference between an actual output shaft rotation speed of the engine and a target rotation speed.例文帳に追加
モータジェネレータのトルクは、エンジンの実際の出力軸回転数と目標回転数との差に応じて制御される。 - 特許庁
To shorten a time required for determining a rotational speed difference between photoreceptor drums.例文帳に追加
各感光体ドラムの間の回転速度差を求めるための時間を短縮する。 - 特許庁
A thrust bearing 18 and a thrust bearing 12 absorb this difference in the rotating speed.例文帳に追加
スラストベアリング18、及びスラストベアリング12は、この回転速度の差を吸収する。 - 特許庁
In order to compensate for the second difference, a first map in which the relation of the second difference and an engine speed target value is set is used to determine the engine speed target value.例文帳に追加
第2差分を補償するため、第2差分とエンジン回転数目標値との関係を設定した第1のマップを使用してエンジン回転数目標値を決定する。 - 特許庁
To input two analog signal and apply a digital operation to the difference thereof at high speed or to apply processing to one input and then apply a digital operation to the difference thereof at high speed.例文帳に追加
2つのアナログ信号を入力してその差分を高速でデジタル演算し、あるいは一方の入力に処理を施した後それらの差分を高速でデジタル演算する。 - 特許庁
Transferring property is improved by providing a difference in circumferential speed between a photoreceptor drum and a transfer means in transferring and providing no difference in the circumferential speed between the photoreceptor drum and the transfer means when not transferring.例文帳に追加
転写時は、感光ドラムと転写手段の周速差をつけて、転写性を向上し、転写時以外は感光ドラムと転写手段の周速差を無くする。 - 特許庁
To allows a kick type shutter device to obtain a stable shutter speed with a small individual body difference.例文帳に追加
蹴飛ばし式のシャッタ装置で個体差が少なく安定したシャッタ速度を得る。 - 特許庁
To transmit comparatively great torque even in a range of small difference in rotation speed, and prevent torque from being quickly increased as the difference in rotation speed is increased.例文帳に追加
回転速度差が小さい範囲でも比較的大きなトルクを伝達することができ、しかも回転速度差の増大に伴ってトルクが急増するのを防止する。 - 特許庁
The regenerative limiting control part 5d more limits regenerative braking torque when performing turning braking as the vehicle speed right and left difference becomes smaller and vehicle speed front and rear difference becomes larger.例文帳に追加
前記回生制限制御部5dは、車輪速左右差が小さいほど、かつ、車輪速前後差が大きいほど、旋回制動時の回生制動トルクをより制限する。 - 特許庁
A first ECU detects an actually measured value Wdiff of wheel speed difference (step 201), and then calculates a theoretical value W of the wheel speed difference based on a yaw rate Ry (step 202).例文帳に追加
第1ECUは、車輪速差の実測値Wdiffを検出し(ステップ201)、続いてヨーレイトRyに基づいて車輪速差の理論値Wを演算する(ステップ202)。 - 特許庁
A movement comparator 10 compares the speed V1a with the speed V1b, reports the information to a train cab, and the like, when some difference is observed at both V1a and V1b, and outputs a higher speed as the speed V2.例文帳に追加
動作比較器10は、速度V1aとV1bを比較し両者に差がある場合、その旨を運転台等に通知すると共に、高い方の速度を速度V2として出力する。 - 特許庁
Even if the speed difference between before and after switching of the speed signal is large, the speed instruction signal for controlling the speed change so as to be moderated can be generated by the integrating circuit 28.例文帳に追加
積分回路28により速度信号の切換前後の速度差が大きい場合でもその速度変化を緩やかに行う制御をするための速度指令信号を生成できる。 - 特許庁
The developing speed of the image data thus obtained is compared with a printing speed from an aspect of a mechanism (S9) and, when the developing speed is slower than the printing speed, the printing waiting time corresponding to the speed difference is set (S10).例文帳に追加
これにより得られたイメージデータの展開速度と機構上の印刷速度とを比較し(S9)、展開速度の方が印刷速度よりも遅い場合には、速度差に応じた印刷待ち時間を設定する(S10)。 - 特許庁
A speed synchronous controller 522 generates a speed difference adjusting signal for adjusting the generated torque or rotation speed of a motor 22 so that the speed difference between the rotation speed VF output by a tachometer 27 of a dynamometer 2 for front wheels and the rotation speed VR output by a tachometer 27 of a dynamometer 3 for rear wheels is zero.例文帳に追加
速度同期制御部522は、前輪用ダイナモメータ2の回転速度計27が出力する回転速度VFと後輪用ダイナモメータ3の回転速度計27が出力する回転速度VRとの速度差が0となるようにモータ22の発生トルクまたは回転速度を調整する速度差調整信号を生成する。 - 特許庁
A target rotation speed mediation part 30e calculates target rotation speed NEt by setting target model rotation speed NEm as an initial value of the target rotation speed, and performing collection based on PI control calculation of difference between the target model rotation speed NEm and actual rotation speed NE, and with the difference as a limit.例文帳に追加
目標回転数調停部30eは目標モデル回転数NEmを目標回転数NEtの初期値とし、目標モデル回転数NEmと実回転数NEとの差のPI制御計算に基づいて、この差を限度として補正することにより目標回転数NEtを算出している。 - 特許庁
When the speed difference Vε is negative and straight running is in progress, or the second intermediate speed command V2 is lower than a curve limit speed Vc, a corrected speed difference Vε' is multiplied by a first deceleration correction value 314; the result of the multiplication is subtracted from the present speed; and the result of the subtraction is set as a speed command Vcom.例文帳に追加
速度偏差Vεがマイナスである場合で、直線走行時又は第2中間速度指令V2がカーブ制限速度Vcよりも小さいときに、修正速度偏差Vε’に第1の減速度補正値314を乗算し、現在速度から減算して速度指令Vcomとして設定する。 - 特許庁
To provide a high-resolution and high-speed pulse phase difference detection circuit, and to provide an A/D conversion circuit using the pulse phase difference detection circuit.例文帳に追加
高分解能かつ高速なパルス位相差検出回路及びこれを用いたA/D変換回路を提供すること。 - 特許庁
If a rotational speed difference (Ne-Nt) between an engine speed Ne and a turbine speed Nt is large when determining a lock-up ON condition (OFF → ON), the lock-up clutch is not engaged but torque reduction control is performed to reduce the engine speed, thus reducing the rotational speed difference (Ne-Nt) (steps ST13 and ST14).例文帳に追加
ロックアップON(OFF→ON)判断時に、エンジン回転数Neとタービン回転数Ntとの差回転(Ne−Nt)が大きい場合は、ロックアップクラッチの係合を行わずに、トルクダウン制御を実行してエンジン回転数を低下させ、差回転(Ne−Nt)を低下させる(ステップST13、ST14)。 - 特許庁
To provide a control device of a torque distribution clutch for a vehicle without slippage of transmission torque control corresponding to a rotational speed difference caused by an input output rotational speed difference of the torque distribution clutch due to a diametrical difference of wheels.例文帳に追加
車輪の径差によるトルク配分クラッチの入出力回転速度誤差に起因する、回転速度差に対応した伝達トルク制御のずれのない車両用トルク配分クラッチの制御装置を提供する。 - 特許庁
When the acceleration request is detected, if a speed difference between the rotation speed of the input shaft of the automatic transmission and the rotation speed of the output shaft of the internal combustion engine is a predetermined value or greater, a fuel injection amount is increased depending on the speed difference.例文帳に追加
加速要求が検出されたとき、自動変速機の入力軸の回転数と内燃機関の出力軸の回転数との回転数差が所定値以上の場合には、回転数差に応じて燃料噴射量を増量する。 - 特許庁
In the ACC/DEC module 220, the ACC signals are accelerated by outputting only the difference when the motor speed is slower than the target speed, and the DEC signals are decelerated by outputting only the difference when the motor speed is faster than the target speed inversely.例文帳に追加
ACC/DECモジュール220は、目標速度よりモータの速度が遅い場合、ACC信号をその差分だけ出力して加速させ、逆に、目標速度よりモータ速度が速い場合、DEC信号をその差分だけ出力して減速させる。 - 特許庁
To provide a winding device provided with an inexpensive and durable mechanism capable of achieving high speed of transfer speed and winding speed and absorbing difference in speed between transfer speed and winding speed.例文帳に追加
本発明は、移送速度および巻き取り速度の高速化に対応することができると共に、廉価で且つ耐久性のある移送速度と巻き取り速度との速度差を吸収する機構を備えた巻き取り装置を提供することを課題とする。 - 特許庁
The speed detection section includes a time difference calculation means for calculating the time difference of output waveforms of input level values obtained from respective elements, and a speed calculation means for calculating the speed of the vehicle 200 from the obtained time difference and the distance between the two monitoring areas 3A, 3B.例文帳に追加
速度検出部は、各素子から得られた入力レベル値の出力波形の時間差を演算する時間差演算手段と、得られた時間差と、二つの監視範囲3A、3B間の距離とから車両200の速度を演算する速度演算手段とを具える。 - 特許庁
The control circuit 200 of a carriage motor 60 includes a speed difference generating circuit 206.例文帳に追加
キャリッジモータ60の制御回路200は、速度偏差生成回路206を有している。 - 特許庁
To suppress shift in color caused by difference in speed between a sheet feeding device and a carrying belt 9a.例文帳に追加
シート給送装置と搬送ベルト9aとの速度差に起因する色ずれを抑える。 - 特許庁
Thus a deceleration can be performed according to a difference in speed and the ratio of speeds of the right and left traveling devices.例文帳に追加
これにより、左右の走行装置の速度差や比に応じた減速が可能となる。 - 特許庁
IMAGE CARRIER SPEED FLUCTUATION PHASE DIFFERENCE DETECTION METHOD AND IMAGE FORMING APPARATUS USING THE METHOD例文帳に追加
像担持体速度変動位相差の検出方法及び該方法を用いる画像形成装置 - 特許庁
To suppress generation of a scratch caused by speed difference between squeeze rollers and a photographic film.例文帳に追加
スクイズローラと写真フイルムとの間の速度差に基づく擦り傷の発生を抑える。 - 特許庁
A speed difference detector 403 receives one of a plurality of target rotational speeds and detects the difference between the given target rotary speed and the current rotary speed of a vibration wave motor 401, and a PI control system 405 determines the drive frequency, based on the difference.例文帳に追加
速度差検出器403が、複数の目標回転速度のうち1つを与えられ、該与えられた目標回転速度と振動波モータ401の現在回転速度との差を検出し、PI制御系405が該差に基き駆動周波数を決定する。 - 特許庁
The output torque of the engine 1 is gradually changed according to the range of the rotation speed difference.例文帳に追加
エンジン1の出力トルクは回転速度差の範囲に応じて段階的に変化させる。 - 特許庁
Consequently, a transfer image can be prevented from shifting in position owing to variation in linear speed difference.例文帳に追加
これにより線速差の変化による転写画像の位置ずれの発生を防止できる。 - 特許庁
It has an ECU which computes the feedback proportioning amount Tfbp proportional to the difference (Ni-No) between the input shaft revolving speed Ni and the target synchronous revolving speed No (Step S41) and computes the proportioning gain n to be in inverted proportion to the difference in the revolving speed |Ni-No| (Step S43).例文帳に追加
ECUは入力軸回転数Niと目標同期回転数Noとの回転数差(Ni-No)に比例するF/B比例量Tfbpを演算し(ステップS41)、回転数差|Ni-No|に反比例する比例ゲインnを演算する(ステップS43)。 - 特許庁
The first paper cutting speed control circuit 2 compares a set value set by a paper cutting speed difference setting device 1 to the speed difference between a first roll 31 and a second roll 32, and controls the rotating speed of the first roll 31 through the first current control circuit 18 and a first driving device 16 so that the above speed difference conforms to the set value.例文帳に追加
第1断紙速度制御回路2は、断紙速度差設定器1により設定された設定値と、第1ロール31と第2ロール32との速度差とを比較し、この速度差が上記設定値となるよう第1電流制御回路18および第1駆動装置16を介して第1ロール31の回転速度を制御する。 - 特許庁
At this time, a speech speed conversion amount calculating part 19 calculates the speech speed conversion amount based on a difference between the measurement result of the average speech speed and the speech speed reference value and a speech speed conversion adjusting part 20 performs speech speed conversion processing based on the calculated speech speed conversion amount.例文帳に追加
このとき、話速変換量算出部19が、平均話速の測定結果と話速の基準値との差分に基づいて話速変換量を算出し、話速変換調整部20が算出された話速変換量に基づいて話速の変換処理を行う。 - 特許庁
For example, when a tape running speed at the time of the fast forwarding operation is faster than a speed at a tape winding surface of the rotary drum type head, a resistance to be applied to the tape is reduced by eliminating the speed difference between the tape running speed and the speed at the winding surface while raising the rotational speed to be matched with the tape running speed.例文帳に追加
例えば、早送り動作時のテープ走行速度が回転ドラム式ヘッドのテープ巻きつけ面における速度よりも速い場合、その回転速度を上昇させてテープ走行速度に一致させ、両者の間の速度差をなくしてテープにかかる抵抗を軽減する。 - 特許庁
When it is the recording medium MRC that causes the failure by providing the speed difference, "small difference" or "no difference" is selected, and when it is the recording medium MRC that does not cause failure even by providing the speed difference, "standard" is selected.例文帳に追加
そして、速度差を設けることによって前記課題の不具合が発生する記録媒体MRCの場合には「小」又は「なし」を選択し、速度差を設けても前記のような不具合が発生しない記録媒体MRCの場合には「標準」を選択するようにする。 - 特許庁
A correction quantity KQNE of an ISC flow rate is determined on the basis of a difference between an actual engine speed NE and the reference engine speed NEBS (Step 116).例文帳に追加
現実の機関回転数NEと基準回転数NEBSとの差に基づいてISC流量の補正量KQNEを求める(ステップ116)。 - 特許庁
Further, the peripheral speed ratio between the upper and lower rolls in the warm difference peripheral speed rolling is controlled to ≥1:1.2, preferably, to ≥1:1.5.例文帳に追加
さらに温間異周速圧延における上下のロール周速度比を1:1.2以上、好ましくは1:1.5以上とする。 - 特許庁
Paper P2 is flexed and bent by an amount equivalent to a speed difference because feed speed from the rear is higher at a point of time when its leading edge reaches the secondary transfer part.例文帳に追加
用紙P2は先端が二次転写部に達した時点で後方からの送り速度が速い分だけ屈曲して撓む。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|