| 意味 | 例文 |
Load controlの部分一致の例文一覧と使い方
該当件数 : 8588件
To provide a session control method for a radio terminal with which a wireless integrated network is realized without applying a load to each wireless access network when selecting the wireless access network, and an interface setting method for setting IP connection in a short period of time when switching the wireless access network.例文帳に追加
無線アクセスネットワークの選択を各無線アクセスネットワークに負荷を与えないで無線統合ネットワークを実現する無線端末のセッション制御方法及び無線アクセスネットワークの切り替える際のIP接続を短時間に設定するインターフェース設定方法を提供する。 - 特許庁
A CPU 16 conveys the printing papers 50 at a substantially constant speed in a predetermined section of sections to which the printing papers 50 are fed by a motor driving each mechanism part, detects the load fluctuation of the motor, and corrects the control quantity based on the detected value.例文帳に追加
CPU16は、各機構部を駆動するモータによって印刷紙50が給紙される区間の所定の区間において印刷紙50をほぼ一定の速度で印刷紙50を搬送して、モータの負荷変動量を検出し、検出した値に基づいて制御量を補正する。 - 特許庁
To provide an engine control system of a road paving machine, capable of preventing adverse effect on a finished surface of a road pavement, which is caused by a large change in a travel speed due to a steep decrease in or stop of the rotation of an engine when an engine load is suddenly increased while an energy-saving mode is selected.例文帳に追加
省エネモードの選択中にエンジン負荷が急激に大きくなってエンジンの回転が大きく低下、または停止することにより、走行速度が大きく変化し道路舗装の仕上げ面に悪影響を与えるのを防止できる道路舗装機械のエンジン制御システムを提供する。 - 特許庁
Even if the direction of a driving current supplied from the battery 25 to a right side motor 22 and a left side motor 24 is switched by the operating switches 26, 28, therefore, any of the direction of the current flowing in the electric storage load current control circuit 30 is made to be the same direction.例文帳に追加
このため、バッテリー25から右側用モータ22及び左側用モータ24に供給される駆動電流の方向が操作スイッチ26、28によって切り替えられても、電動格納負荷電流制御回路30を流れる電流の方向は何れも同一方向とされる。 - 特許庁
When the load accumulated value exceeds a prescribed threshold, the decoding processing control part 1 controls so as to select a pseudo PhCH decoding processing part 4, a pseudo TrCH decoding processing part 10 and a pseudo E-DCH decoding processing 42 for generating dummy data and omits decoding processing.例文帳に追加
前記負荷累積値が所定の閾値を超えた場合、復号処理制御部1は、ダミーデータを生成する擬似PhCH復号処理部4、擬似TrCH復号処理部10、擬似E−DCH復号処理部42を選択するよう制御し、復号処理を省略する。 - 特許庁
The drainage pumping station is provided with a pump 10 and a drive machine 30 driving the pump 10, and is further provided with a detector 71 indicating an operation state of the drainage pumping station and a control device 90 operating the pump 10 at a light load when output value of the detector 71 reaches an alarm point.例文帳に追加
排水機場は、ポンプ10と、該ポンプ10を駆動する駆動機30とを備え、さらに、排水機場の運転状態を示す検知器71と、検知器71の出力値が所定の警告点に到達したときに、ポンプ10を低負荷で運転させる制御装置90とを備える。 - 特許庁
At low-load operation, the device stops the switching of the active filter circuit, to detect the input commercial power supply voltage supplied to the power supply from the secondary side, and determines the maximum apparent power from the detected result to change the control sequence based on it.例文帳に追加
軽負荷時に、前記アクティブフィルタ回路のスイッチングを停止し、二次側より前記電源に供給される商用電源の入力電圧を検出して、検出結果から最大皮相電力を決定し、決定される最大皮相電力に基づいて制御シーケンスを変更する。 - 特許庁
When the load 16 becomes its ordinary state to make the sensed voltage VA of the current sensing resistor 22 not smaller than the reference voltage VR2 of the reference power supply 23, performing the ON/OFF control of the MOSFET 4 for synchronized rectifications by the output signal of the comparison circuit 26, a rectifying operation is performed.例文帳に追加
負荷16が通常状態となり、電流検出用抵抗22の検出電圧V_Aが基準電源23の基準電圧V_R2以上になると、比較回路26の出力信号により同期整流用MOS-FET4がオン・オフ制御され整流動作が行われる。 - 特許庁
A processing circuit includes a control module 261P for setting priorities for the plurality of content processes and, with an increasing load that makes difficult the concurrent execution of the plurality of content processes, limits the processing operation of the content process in the ascending order of priorities.例文帳に追加
処理回路261は複数のコンテンツ処理に対して優先順位を設定し、複数のコンテンツ処理の同時並列的な実行を困難にする負荷の増大に伴って優先順位の低い側のコンテンツ処理から処理動作を制限する制御モジュール261Pを含む。 - 特許庁
A boiler master control means 51 calculates a boiler load based on the main steam pressure P2 and the main steam pressure set value Ps, and a fuel distributing means 53 calculates the BOG fuel quantity command and the alternative fuel quantity command to preferentially consume the BOG fuel.例文帳に追加
ボイラマスタ制御手段51は主蒸気圧力P2と主蒸気圧力設定値P_Sとに基づいてボイラ負荷を算出し、燃料配分手段53は、BOG燃料を優先的に消費するようにBOG燃料量指令および代替燃料量指令を算出する。 - 特許庁
To provide a control method of refrigeration cycle using an orifice part for an expansion device, capable of exactly estimating the drive torque of a variable displacement compressor and controlling the drive torque of the variable displacement compressor, which is an engine load, according to required engine output torque.例文帳に追加
容量可変型圧縮機の駆動トルクを正確に推定し、必要とするエンジン出力トルクに応じてエンジン負荷である容量可変型圧縮機の駆動トルクを制御することができるような、膨張装置にオリフィス部を用いた冷凍サイクルの制御方法を提供すること。 - 特許庁
When an overcurrent detector 8 recognizes that the current supplied to a load 20 is abnormally large, a control unit 7 turns on the bidirectional thyristor 32 via a driving part 9 to bypass the overcurrent and, immediately after that, turns on the electromagnetic relay 33 to bypass the overcurrent via the electromagnetic relay 33.例文帳に追加
過電流検知部8により負荷20に供給される電流が異常に大きいことを認識すると、制御部7は駆動部9を介して双方向サイリスタ32をオンさせて過電流をバイパスし、その直後に電磁リレー33をオンさせて該電磁リレー33を介して過電流をバイパスする。 - 特許庁
An electronic control device 40 controls the changes over of the combustion mode of the internal combustion engine 10 between the stratified combustion and the homogeneous stoichiometric combustion, based on an engine load factor and engine rotation speed, and when a rich spike processing is required, the combustion mode is set to the homogeneous rich combustion.例文帳に追加
電子制御装置40は、機関負荷率及び機関回転速度に基づいて内燃機関10の燃焼モードを成層燃焼と均質ストイキ燃焼との間で切替制御するとともに、リッチスパイク処理の要求があるときに燃焼モードを均質リッチ燃焼に設定する。 - 特許庁
When a setting member 41 sets a trapezoidal voltage waveform of power being supplied from the uninterruptible power supply unit 1 to a load apparatus, a control means 43 controls the sine wave generating means 44 to generate a sine wave having an amplitude larger than that of a triangular wave.例文帳に追加
そして、設定部材41において当該無停電電源装置1から負荷機器へ供給する電力の電圧波形が台形波に設定されると、制御手段43は、正弦波生成手段44により三角波より振幅が大きい正弦波を生成させる。 - 特許庁
The control device so determines the target throttle valve opening TAfgt(k) that a torque variation amount ΔTRQ does not exceed a threshold ΔTRQth (steps 720, 730), and estimates an estimated load KLs(k) for a combustion stroke from the target throttle opening.例文帳に追加
制御装置はトルク変動量ΔTRQの大きさが閾値ΔTRQthを越えないようにしながら目標スロットル弁開度TAtgt(k)を決定し(ステップ720、730)、その目標スロットル弁開度から今回の燃焼行程に対する推定負荷KLs(k)を推定する。 - 特許庁
Structural parts of a power supply portion and structural parts of a control portion are accommodated in the first case 501, and operational panel side parts 7 to 11 including receptacles connected with plugs attached to an electrical code led to the load are accommodated in the second case 502 to be attached at the operational panel portion 503.例文帳に追加
第1のケース501内に電源部の構成部品と制御部の構成部品とを収容し、負荷につながる電気コードに取り付けられたプラグが接続されるレセプタクルを含む操作パネル側部品7〜11を第2のケース502内に収容して操作パネル部503に取り付ける。 - 特許庁
Thus, when excessiveness of the load variation of the front wheels is discriminated, a pressure reducing sensitivity adjusting means adjusts the pressure reducing reference speed for the front wheels according to the decrease of the detected car body acceleration, and facilitates transfer to a pressure reducing mode in relation to the hydraulic pressure control of the front wheels.例文帳に追加
このように前輪の荷重変動が過大と判定されたときには、減圧感度調整手段により、検出車体加速度の低下に応じて前輪に対する減圧基準速度を高くするように調整し、前輪の液圧制御に関し減圧モードへの移行を容易にする。 - 特許庁
This loading platform lifter 3 with a loading platform 301 having a half width of a load box 2 is installed on one side, and a control box 5 with an operating face directed to a vehicle rear side is arranged between a lifter 300 and a step 4 opposed to it.例文帳に追加
荷受台301の幅を荷箱2の半分の幅とした荷受台昇降装置3を荷箱2の片側に寄せて設け、その昇降装置300と、これと反対側に設けられたステップ4との間に、操作面を車体後方側に向けたコントロールボックス5を配置する。 - 特許庁
The upper part of the shearing key 70 is stored in a storage recess 76 of a sole plate 72 in the state of placing the bridge girder 16 on a support on the bridge pier 12 in such a manner that the storage recess 76 is put almost in non contact with the shearing key 70 without operation of vertical load on the seismic control device 44.例文帳に追加
橋脚12上の支承に橋桁16を載置した状態で、ソールプレート72の収容凹部76にせん断キー70の上部が収容され、垂直荷重が制震装置44に作用することなく、収容凹部76とせん断キー70とがほぼ非接触状態となっている。 - 特許庁
A running speed controlling means (2) for controlling the running speed of a machine body, an engine control means (4) for controlling output of an engine (3) by controlling fuel supply corresponding to the load, and a fuel supply detecting means (5) for detecting fuel supply in real time, are provided.例文帳に追加
機体の走行速度を制御する走行速度制御手段(2)と、負荷に応じて燃料供給量を調整してエンジン(3)の出力を制御するエンジン制御手段(4)と、リアルタイムで燃料供給量を検出する燃料供給量検出手段(5)とを設ける。 - 特許庁
This vehicle controller 1 includes an active stabilizer device 10 as a tread load regulating part for making tread loads of front wheels and rear wheels get different in left and right wheels, a target yaw rate setting part 102 for setting a target yaw rate, and a yaw rate control part 104 for regulating an actual yaw rate.例文帳に追加
車両制御装置1は、前輪および後輪の接地荷重を左右輪で異ならせるための接地荷重調節部としてのアクティブスタビライザ装置10と、目標ヨーレートを設定するための目標ヨーレート設定部102と、実ヨーレートを調節するためのヨーレート制御部104と、を備える。 - 特許庁
Furthermore, when it is equipped with a control means CT and it detects the tire air pressure less than the specified value during vehicle's traveling, it controls braking force and or driving force to these wheels WL so as to make the tire load not exceed the upper limit value as to the air pressure lowered wheel.例文帳に追加
更に、制御手段CTを備え、車両が走行中に所定値以下のタイヤ空気圧を検出したときには、空気圧低下車輪に関しタイヤ負荷が上限値を越えないように、各車輪WLに対する制動力及び/又は駆動力を制御する。 - 特許庁
As to the target material and backing plate material, a structural control heat treating process for the target material and a solid phase diffusion joining process are simultaneously performed at a joining temperature of 400 to 500°C under the joining load pressure of ≤50 MPa for a joining time of ≤2 hr in a vacuum atmosphere of ≤0.1 Pa.例文帳に追加
該ターゲット材とバッキングプレート材とを、0.1Pa以下の真空雰囲気中、400℃〜500℃の接合温度、50MPa以下の接合時負荷圧力及び2時間以内の接合時間で、ターゲット材の組織制御熱処理工程と固相拡散接合工程とを同時に行うこと。 - 特許庁
A power train control unit 100 adjusts the position of a pressing load of the pressing member of the starting clutch according to inclination in a fore-and-aft direction of a vehicle before the complete engagement of the starting clutch 8 when the difference in a number of rotations between the power source and the number of rotations of the input shaft converges.例文帳に追加
パワートレーン制御ユニット100は、動力源と入力軸回転数の回転数差が収束する発進クラッチ8の完全締結前に、車両の前後方向の勾配に応じて、前記発進クラッチの押し付け部材の位置もしくは押し付け荷重を調整する。 - 特許庁
At the first period t1-t2 large in flow rate and high in pressure, high pressure off-gas from a PSA device 19 is stored at a second tank T2 by opening a second stop valve V2 while closing a first stop valve V1 and supplied to the load from a pressure control valve V3 through a first tank T1.例文帳に追加
PSA装置19からのオフガスを、大流量、高圧力の第1期間t1〜t2では、第1開閉弁V1を閉じたままで、第2開閉弁V2を開き、高圧力オフガスを第2タンクT2に貯留し、圧力制御弁V3から第1タンクT1を経て負荷に供給する。 - 特許庁
In a wiper motor drive controller which is equipped with a thermal FETQA being switched, according to a PWM control signal 152, and controlling the power supply from a power source to a wiper 102, a comparator CMP2 compares the load current flowing to the wiper motor 102 with a prescribed threshold.例文帳に追加
PWM制御信号152に応じてスイッチング制御され電源からワイパモータ102への電力供給を制御するサーマルFETQAを備えたワイパモータ駆動制御装置において、コンパレータCMP2は、ワイパモータ102に流れる負荷電流を所定のしきい値と比較する。 - 特許庁
This constant-current driving control circuit is constituted so that load is always driven in stable driving timing by providing a rapid charging circuit in the phase compensating capacitor and charging it until the potential thereof becomes the same set potential just after starting switching operation.例文帳に追加
位相補償用コンデンサに急速急速充電回路を設け、スイッチ操作の開始直後に前記位相補償用コンデンサの電位を決められた同一電位まで充電し、常に安定した駆動タイミングで負荷を駆動できるようにした定電流駆動制御回路である。 - 特許庁
Out of elements constituting the synchronous input control device 5, a breaking current polarity judgment part 51 judges polarity of breaking current at separation of a capacitive load 4 from an AC power source 1 by the power switch 2 based on measured signals of the rheotrope for instruments 3.例文帳に追加
同期投入制御装置5を構成する要素の内、遮断電流極性判別部51は、計器用変流器3の測定信号に基づき電力用開閉器2にて容量性負荷4を交流電源1から切り離す際の遮断電流の極性を判別する。 - 特許庁
Consequently, since the heat sensing actuator 300 opens and closes with interlocking with the thermostat 220, exhaust gas heat recovery can be executed through engine cold time without hunting of the exhaust control valve 160 with responding to fluctuation of cooling water temperature near an engine outlet corresponding to engine load.例文帳に追加
これにより、感熱アクチュエータ300がサーモスタット220に連動して開閉するので、エンジン負荷に対応したエンジン出口付近での冷却水温の変動に応答して排気制御弁160をハンチングさせることなく、エンジン冷間時を通じて排気熱回収を実行できる。 - 特許庁
The blade member (rotary body) arranged in the rice-polishing part housing rice is rotationally driven by a drive device 50 to remove rice bran and load including the drive device 50 is controlled according to a predetermined process by a control means 7 and polished rice is stored in a rice receiving part.例文帳に追加
米を収納する米とぎ部の内部に配設した羽根部材(回転体)を駆動装置50により駆動して回転させて除糠し、制御手段7により駆動装置50を含む負荷を所定の工程に従い制御し、米とぎされた米を米受け部に貯える。 - 特許庁
To provide a power source circuit which can control the connection of an electric double layer capacitor to a DC power supply source in response to the operation/non-operation of a load when the consumption of the current when left unused cannot be ignored and which can alleviate a leakage current depending upon the double layer capacitor.例文帳に追加
放置状態での電池の消耗が無視できないとき、負荷の動作/非動作に応じて直流電源供給源への電気二重層コンデンサの接続制御を可能にし、電気二重層コンデンサに依存するリーク電流を軽減できる電源回路を提供する。 - 特許庁
This device comprises a plurality of contant rate pumps 1, 2 of a constant rotating speed, a common load generation part 9 is connected to the delivery ports of the pumps 1, 2, and the primary side pressure constant control type two-way valves 11, 12 for constantly controlling the output of the delivery ports are mounted on the delivery ports of thepumps 1, 2.例文帳に追加
回転速度が一定に固定された定速型ポンプ1,2を複数台備え、各ポンプ1,2の吐出部に共通の負荷発生部9を接続し、ポンプ1,2の吐出部に、吐出部の圧力を一定圧に制御する一次側圧力一定制御型の二方弁11,12を設けている。 - 特許庁
A control section 100 controls a voltage detection section 71 to detect a change in the discharge voltage of a battery 70 between a state in which a predetermined load is applied to the battery 70 and a state in which it is not applied, determines the extent of the degradation of the battery 70 in accordance with the magnitude of the change, and informs a user of it.例文帳に追加
制御部100は、電圧検出部71を制御して、バッテリ70に所定の負荷を与えた時と与えない時とで、その放電電圧の変化を検出し、その変化の大きさに応じてバッテリ70の劣化度合いを判定し、これをユーザに報知するようにしたものである。 - 特許庁
The in-vehicle device includes: a vibration detecting part 2 to detect vibration; and a control part 3 that receives a request to load/unload the recording medium (CD 10) from the outside, and prohibits execution of the loading/unloading request when the magnitude of the vibration detected by the vibration detecting part 2 exceeds a predetermined value.例文帳に追加
車載機器は、振動を検知する振動検知部2と、外部から記録媒体(CD10)の搬入出要求を受け付け、振動検知部2により検知された振動が所定値以上あった場合に搬入出要求の実行を禁止する制御部3と、により構成される。 - 特許庁
The supercharging system for an internal combustion engine includes a valve control means which controls a valve 72 so that, if a required load is increased, a flow rate of gas flowing from a pressure accumulation vessel 70 to an exhaust passage K on an upstream side of a turbine wheel 48 based on a transmission gear ratio of a transmission 86.例文帳に追加
本発明に係る内燃機関用過給システムは、要求負荷が増加したとき、変速機86の変速比に基づいて蓄圧容器70内からタービンホイール48上流側の排気通路Kへのガス流量を調整するように弁72を制御する弁制御手段を備える。 - 特許庁
In a circuit for driving an inductive load by the on/off control of first and second switching transistors connected between a power source potential and a ground potential, a guard ring 17 for preventing influence to another element is provided on the same semiconductor substrate 11, and this guard ring is connected to the ground potential GND.例文帳に追加
電源電位とアース電位間に接続された第1、第2スイッチングトランジスタのオン・オフ制御により誘導性負荷を駆動する回路において、同一半導体基板11に他の素子への影響を防止するガードリング17を設けるとともに、このガードリングをアース電位GNDに接続する。 - 特許庁
When the steering load is large (for example, in stopping of the vehicle), the vehicle is prevented from being deviated from the target route by resetting the route suppressing the variation dγ/dp with respect to a traveling distance p of the turning curvature γ in consideration of the occurrence of control delay of an automatic steering.例文帳に追加
操舵負荷が大きい(例えば、車両停止時等)には、自動操舵の制御遅れ発生を考慮して、旋回曲率γの走行距離pに対する変化量dγ/dpを抑制した経路を再設定することで目標経路から車両が逸れるのを防止する。 - 特許庁
When decelerating from the high load operation, when the cooling water temperature is lower than the predetermined upper limit temperature (YES in Step S10, YES in S11, and NO in S12 and S13), after disengaging a clutch, an engine is stopped, and regenerative control by a motor generator is performed (Step S19 and S20).例文帳に追加
高負荷運転からの減速時に冷却水温が所定の上限温度よりも低い場合は(ステップS10肯定、S11肯定、S12、S13否定)、クラッチを切断した後、エンジンを停止するとともにモータジェネレータによる回生制御を行う(ステップS19、S20)。 - 特許庁
In order to sustain a constant rotational speed at all times, current PWM control for varying power thrown to the motor depending on variation in load is employed, and the generated pressure and discharge amount of the pump are managed by determining the phase of the roll, based on the current PWM value.例文帳に追加
回転数を常に一定に保つため、負荷変動に応じてモータへの投入電力を変動させる電流PWM制御を採用するとともに、その電流PWM値に基いてコロの位相を確定し、ポンプの発生圧力および排出量を管理する。 - 特許庁
To provide a video server control system and a composite source recording method by providing a simpler system in the case of recording a composite source to a video server so as to reduce the system cost and producing a composite source with a simple method so as to relieve the load of an operator.例文帳に追加
ビデオサーバへの複合素材の記録において、より簡便なシステムを提供することによってシステムのコストダウンを図ると共に、簡便な方法により複合素材を生成してオペレータの負担を軽減することを可能とする、ビデオサーバ制御システム及び複合素材記録方法を提供する。 - 特許庁
A control unit of a navigation device determines a driving skill of a driver based on age, driving experience, and driving operations of the driver, and also estimates a driving load on the driver based on the driving skill, driving operations of an own vehicle, and static and dynamic environments of the own vehicle.例文帳に追加
ナビゲーション装置の制御部は、年齢,運転歴や、運転操作に基づき、ドライバの運転技量を判定すると共に、運転技量と、自車両の運転操作や自車両周辺の静的環境,動的環境に基づき、該ドライバにとっての運転負荷を推定する。 - 特許庁
To carry out a quick and proper dealing operation for obtaining stable operation, by making clear a control reference of in-furnace flowability for a flowing medium, when switching the kind of a raw material coal fed into a fluidized bed boiler, and to reduce the load on the operator.例文帳に追加
流動床ボイラにおいて投入する原料炭の種類を切り替えた際に、流動媒体の炉内流動性の管理基準を明確なものとすることにより、迅速かつ適切な対応操作を行って安定した操業を図ることができるとともに、オペレータの負担を軽減する。 - 特許庁
To reduce the signal transmitting and receiving load of a central processor even in a place where a large number of lighting facilities are arranged in a wide range, and shorten setting time while reducing overall cost by simplifying the setting work of control.例文帳に追加
広範囲で照明設備の数多く配置されるような場所であっても、中央処理装置による信号の送受の負荷を軽減させることができ、しかも制御の設定作業を簡易化して設定時間を短縮することができるとともに、全体的なコストを低減すること。 - 特許庁
A signal such as a car speed sensor signal is inputted to the judgment part H other than the respective signals SS1, etc., and the judgment part H carries out a driving control based on a combination of the respective signals and the above respective signals SS1, etc., such that a power is intermittently supplied to the load.例文帳に追加
判断部Hには前記各信号SS1等以外に車速センサ信号等の信号が入力され、判断部Hは、その各信号及び前記各信号SS1等の組み合わせに基づいて、負荷に対して断続的に電力を供給するように駆動制御を行う。 - 特許庁
An ECU (injection control unit) determines that load of a fuel pump is stabilized at the time (time t11) when pressure feeding delay time Δtp of the fuel pump elapses from the time (time t9) when fuel pressure feeding amount commanded to the fuel pump reaches pressure feeding amount required for maintaining target injection pressure.例文帳に追加
ECUは、燃料ポンプに指令する燃料圧送量が、目標噴射圧を維持するために必要な圧送量に達した時点(時刻t9)から、燃料ポンプの圧送遅れ時間Δtpが経過した時点(時刻t11)で、燃料ポンプの負荷が安定したと判定する。 - 特許庁
To provide a mechanism allowing an optional number of USB devices within an allowable range to perform synchronous operation and trigger operation without placing a large calculation load on a host to thereby supplement a USB specification to cause the host to perform other operations such as control, data transfer, logging and analysis.例文帳に追加
ホストに大きな計算負荷をかけることなく、許容される範囲の任意の数のUSBデバイスが同期動作及びトリガ動作することを可能にするメカニズムを提供してUSB仕様を補い、ホストに、制御、データ転送、ロギング、解析など、他の作業を行わせる。 - 特許庁
To provide a traveling state system capable of virtually verifying and testing the effects of variations in electrical load caused by the actuation of accessories such as air conditioners and car audios mounted to vehicles to the travel control of a vehicle while the vehicle is traveling without having to actually mount the accessories.例文帳に追加
車両に搭載されるエアコンやカーオーディオなどの付属装置を実装することなく、それらの付属装置を作動することで生じる車両走行中の電気負荷変動による車両走行制御への影響を仮想的に検証試験できる走行状態システムを提供する。 - 特許庁
As a result, the feedback control of a supply voltage VLED brings the lowest voltage in the output terminal voltage of the current output circuits 2-1 to 2-n closer to the minimum voltage of the margin, and is stably operated, thus efficiently driving the load with a lower supply voltage VLED.例文帳に追加
これにより、電流出力回路2−1〜2−nの出力端子電圧における最低電圧をマージン分の最小限の電圧に近づける電源電圧VLEDの帰還制御が安定に動作するため、より低い電源電圧VLEDで効率よく負荷を駆動できる。 - 特許庁
To provide a heat exchange method for cooling or heat recovery which realizes power-saving, highly efficient, inexpensive and miniaturized apparatus, and extremely stable temperature control against fluctuation in a load or fluctuation in factory cooling water when the factory cooling water whose temperature is lower than predetermined temperature is supplied.例文帳に追加
所定温度より低い温度の工場冷却水が供給される場合に、省電力で高効率、かつ低コストで小型、さらに負荷変動や工場冷却水の変動に対し極めて安定な温度制御が可能な冷却または熱回収を行う熱交換方法を提供できる。 - 特許庁
A vector instruction issuing part sorts a plurality of elements comprising the vector data to an element group and controls to start the tranferring the element group with all element out of the plurality of element groups read from the main memory by the memory access control part from the load buffer to the vector processing part.例文帳に追加
ベクトル命令発行部は、ベクトルデータを構成する複数の要素を複数の要素群に分け、複数の要素群のうちで全ての要素がメモリアクセス制御部によりメインメモリから読み出された要素群に対して、ロードバッファからベクトル処理部への転送を開始するように制御する。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|