compressorを含む例文一覧と使い方
該当件数 : 22706件
To provide an oxygen inhalator capable of optimizing the quantity of compressed air generated by a compressor by measuring the place of use of the oxygen inhalator by means of a global positioning system and automatically setting a control pattern according to the altitude of the place of use.例文帳に追加
酸素吸入装置の使用場所を全地球測位システムで計測し、使用場所の高度に応じて制御パターンに自動設定することでコンプレッサで発生される圧縮空気量を最適にすることができる酸素吸入装置の提供。 - 特許庁
A stopping brake 5 is installed on the car 21, and a brake releasing solenoid valve 2132 for controlling the stopping brake and an air compressor 212a for feeding compressed air are also mounted thereon to eliminate crossover air pipes between the cars and the vehicle.例文帳に追加
台車21には停留ブレーキ5を装備するとともに、これを制御するブレーキ緩解用電磁弁2132、及び、圧縮空気自給用の空気圧縮機212aを搭載して、台車間及び車両間の渡り空気配管を排除する。 - 特許庁
At the stop of an engine E, the air conditioner ECU 70 controls the refrigerant discharge per unit time of the compressor body 101 by regulating the rotating speed of the electric motor part 102 in the state of the control valve 39 being fixed to total closure.例文帳に追加
エンジンEの停止時においてエアコンECU70は、制御弁39を全閉に固定した状態で電動モータ部102の回転速度を調節することで、コンプレッサ本体101の単位時間当たりの冷媒吐出量を制御する。 - 特許庁
A V-belt 11 is extended over a crank pulley 3 mounted to a crank shaft 2, a pulley 7 for a motor generator mounted to a rotation shaft 6 of the motor generator 5, a pulley 10 for the accessary mounted to a rotation shaft 9 of a compressor 8.例文帳に追加
Vベルト11が、クランク軸2に装着されたクランクプーリ3と、電動発電機5の回転軸6に装着された電動発電機用プーリ7と、コンプレッサ8の回転軸9に装着された補機用プーリ10とに掛け渡されている。 - 特許庁
In a vane compressor 10, an oil discharge hole 42b of which one end opens toward a lowest part of an oil separation chamber 43, and of which another end opens toward an outside of a case 42 and extends in a horizontal direction is formed at an oil separator 40.例文帳に追加
ベーン圧縮機10において、油分離器40には一端が油分離室43の最下部に向けて開口するとともに他端がケース42外に向けて開口し水平方向へ延びる油排出孔42bが形成されている。 - 特許庁
When the determination result information D57A indicates the presence of scale deposition abnormality, the scale deposition abnormality-time execution unit 58 executes a scale deposition abnormality processing by stopping the operation of the heat pump type water heater, including stopping a compressor 25 and the like.例文帳に追加
スケール付着異常時実行手段58は判定結果情報D57Aが「スケール付着異常あり」を指示する場合、圧縮機25の停止等を含むヒートポンプ式給湯装置の運転停止によるスケール付着異常処理を実行する。 - 特許庁
In a fixed scroll 18 constituting a scroll-type compressor 10, a supply path 26 is formed along a fixed side convoluted wall 24, and the oil storage room of a rear housing 14 and the leading end 24a of the fixed side convoluted wall 24 are communicated with each other.例文帳に追加
スクロール型圧縮機10を構成する固定スクロール18には、固定側渦巻壁24に沿って供給通路26が形成され、リアハウジング14の貯油室と前記固定側渦巻壁24の先端部24aとを連通している。 - 特許庁
To provide a hermetic compressor for facilitating the positioning of a connection pipe, a suction pipe and a discharge pipe in the axial direction, assuring easy work for welding and brazing and producing an increase in bending strength of the suction pipe and the discharge pipe.例文帳に追加
接続管、吸入管および吐出管の軸方向の位置決めが容易になされ、また、溶接及びロー付の作業が容易かつ、確実にでき、更に吸入管及び吐出管の曲げ強度を増すことができる密閉型圧縮機を提供する。 - 特許庁
Primary side one end of the three-way solenoid valve is connected to a pressure source, and the three-way solenoid valve is controlled by a capacity control signal of a timer or a compressor, and the lubricating oil leaked out of the shaft seal device is recovered by using pressure of the pressure source.例文帳に追加
三方電磁弁の1次側の一端は圧力源に接続し、タイマーまたは圧縮機の容量制御信号にて三方電磁弁を制御し圧力源の圧力を利用して、軸封装置より洩れ出た潤滑油を回収する。 - 特許庁
In a refrigerant compressor, the O-ring 43 provided between connection faces 50, 51 of a housing is equipped with a ring main body 42 of which section area is a circle and flat area is a ring shape and a ring protrusion 41 formed along an outer peripheral of the main body 42.例文帳に追加
冷媒圧縮機において、ハウジングの接合面50,51間に介在されたOリング43は、断面円形でかつ平面環状をなすリング本体42と、該本体42の外周に沿って形成された環状突起41とを備えている。 - 特許庁
To satisfy both of usability and securement of reliability of a use-side heat exchanger in a refrigerating device by allowing restart of operation in a normal state after the stop of operation of a compressor, and restricting the restart of operation in an abnormal state.例文帳に追加
冷凍装置において、圧縮機の運転停止後に正常状態であれば運転復帰を可能としつつ異常状態であれば運転復帰を制限して、使い勝手と利用側熱交換器の信頼性の確保とを両立すること。 - 特許庁
When an air compressor is assembled, the casing 1 and the revolving scroll 12 are assembled in a state of being positioned by an assembling assist pin 22, and the resolving scroll 12 and the fixed scroll 5 are assembled in a state of being positioned by an assembly assist pin 23.例文帳に追加
そして、空気圧縮機の組立時には、ケーシング1と旋回スクロール12とを組立補助ピン22により位置合わせした状態で組付け、旋回スクロール12と固定スクロール5とを組立補助ピン23により位置合わせした状態で組付ける。 - 特許庁
A controller 30 of the auger type ice making machine 1 controls rotational frequency of a compressor motor 23 of the refrigerating machine 20 according to a result of the comparison of load torque TRQ of an auger motor 6 detected by a load cell 31, and upper and lower limit values TRQ_H, TRQ_L (steps 11-17).例文帳に追加
オーガ式製氷機1のコントローラ30は、ロードセル31により検出されたオーガモータ6の負荷トルクTRQと、上下限値TRQ_H,TRQ_Lとの比較結果に応じて、冷凍機20の圧縮機モータ23の回転数を制御する(ステップ11〜17)。 - 特許庁
To provide an air conditioner constituting its characteristic feature of improved workability at the time of assembling the air conditioner and a maintenance property and improved silence of the air conditioner having an outdoor unit with a built-in compressor.例文帳に追加
空気調和装置の組立て時の作業性および、メンテナンス性を向上させるとともに、圧縮機を内蔵した室外ユニットを有する空気調和装置の静音性を向上させたことを特徴とする空気調和装置を提供することにある。 - 特許庁
To save cost and labor and time for exchange of an adsorbent by prolonging the service life of the adsorbent the and to enhance the quality of the treated water by making an oil component absorbed to a low concentration, in an oily water separator for removing the oil component from drain discharged from an air compressor, etc.例文帳に追加
空気圧縮機等が排出するドレンから油分を除去する油水分離装置において、吸着材の寿命をより長くして交換費用や手間を削減すると共に、油分を低濃度まで吸着し処理水の品質を高める。 - 特許庁
Heat of a refrigerant discharged from a first compression means 11a of a two-stage compression type compressor 10 is released by a radiator 12, and the refrigerant from which heat is released is decompressed by a fixation throttle 13 to separate gas and liquid by a gas liquid separator 14 on the intermediate pressure side.例文帳に追加
二段昇圧式の圧縮機10の第1圧縮手段11aから吐出された冷媒を、放熱器12にて放熱させ、放熱した冷媒を固定絞り13にて減圧させて中間圧側気液分離器14にて気液分離する。 - 特許庁
A high temperature side cooling circuit 22 comprises a compressor 24, a condenser 25, a gas-liquid separator 26, a dehydrator 27, a capillary tube 28, a heat exchanger 29, a dehydrator 30, a capillary tube 31, a cascade condenser 32, and an expansion tank 33.例文帳に追加
さらに、高温側冷凍回路22は、圧縮器24、凝縮器25、気液分離器26、デハイドレータ27、キャピラリーチュ−ブ28、熱交換器29、デハイドレータ30、キャピラリーチュ−ブ31、カスケードコンデンサ32、及び膨張タンク33により構成されている。 - 特許庁
To improve the reliability of a compressor, and at the same time, to comfortably operate an air conditioner for drying by preventing an indoor pressure reducer from being operated continuously in a closed state, when the air conditioner is operated for drying in a cooling cycle.例文帳に追加
冷房サイクルによるドライ運転時に室内側の減圧器が閉塞状態で連続運転されるのを防止して、圧縮機の信頼性を向上できると共に、快適なドライ運転を行うことができる空気調和機を提供する。 - 特許庁
To prevent a stationary scroll relatively displaceable in the axial direction from inclining in an air compressor applying pressure from an end plate back surface of the stationary scroll and keeping clearance between teeth tip of the stationary and a rotary scrolls and the end plate appropriate for high compression performance.例文帳に追加
高い圧縮性能を出す為に固定スクロール鏡板背面より圧力を与え,固定・旋回スクロールの歯先と鏡板との隙間を適切に保つ気体圧縮機において,軸方向に相対変位可能な固定スクロールが傾くのを防止する。 - 特許庁
The hot water heat exchanger 42 is provided on a branch line 43 branched from a liquid pipe between a first expansion valve 24 for the outdoor heat exchanger 23 and a second expansion valve 32 for an indoor heat exchanger 31, and connected on a suction side of a compressor 21.例文帳に追加
上記温水熱交換器(42)は、室外熱交換器(23)用の第1膨張弁(24)と室内熱交換器(31)用の第2膨張弁(32)との間の液配管から分岐して圧縮機(21)の吸込側に接続された分岐配管(43)に設けられている。 - 特許庁
When processing related to the recording of the imaging result on the recording medium is not executed; the motion vector of the imaging result generated by an imaging element is detected with a data compressor, and operation is switched by detecting the movement of the device with the motion vector.例文帳に追加
本発明は、撮像結果の記録媒体への記録に係る処理を実行していない場合に、データ圧縮部により撮像素子による撮像結果の動きベクトルを検出し、この動きベクトルにより装置の動きを検出して動作を切り換える。 - 特許庁
The internal heat exchanger 15 which carries out heat exchange between refrigerant after passing a radiator 11 and refrigerant before sucked into a compressor 10 is installed in a space on the vehicle rear side of a fan shroud 32 and on the side of the outer periphery of a blower 31.例文帳に追加
放熱器11を通過した後の冷媒と圧縮機10に吸入される前の冷媒との熱交換を行う内部熱交換器15を、ファンシュラウド32の車両後方側で且つ送風機31の外周側のスペースに設置する。 - 特許庁
To provide an air conditioner to which a target temperature for controlling a temperature is input from a remote controller, and performing inverter control so that a compressor is not stopped when the temperature is close to the target temperature, thus a cooling operation at an excessively-low temperature can be prevented.例文帳に追加
リモコンから温度制御の目標温度が入力され、目標温度に近づいたとき圧縮機を停止させないようにインバータ制御を行う冷房時に必要以上に低温での冷房運転を回避する空気調和機を提供する。 - 特許庁
Since the capacity of the screw compressor is controlled in accordance with a supply current value and a discharged gas pressure value, the relatively lower precision current sensor 12 is required for detecting the supply current value, resulting in the inexpensive refrigerating plant.例文帳に追加
スクリュー圧縮機2について、供給電流値と吐出ガス圧力値とに基いて容量制御を行なうので、供給電流値を検出する電流センサ12は精度が比較的低いものでよいから、冷凍装置が安価に形成できる。 - 特許庁
To provide a compact and space-saving filter regenerating device, requiring a small amount of backwashing air which can be generated by a small compressor or blower normally equipped in a general mechanic's shop, and easily operated or managed.例文帳に追加
必要な逆洗空気の量が少なく、一般の修理工場等に通常備えられる小型のコンプレッサやブロアで対応可能であって、コンパクト化、省スペース化が図られていて、操作及び管理が容易なフィルタの再生装置を提供する。 - 特許庁
By absorbing heat from the heat storage liquid that has become a higher temperature than outside air by heat storage, and carrying out heating, reduction of a circulation flow rate of the refrigerant is prevented, a compression ratio of a compressor 1 is reduced, and heating efficiency can be improved.例文帳に追加
次いで蓄熱によって外気より高温になった蓄熱液体から吸熱して暖房することによって、冷媒の循環流量の低下を防止し、かつ圧縮機1の圧縮比を減らして暖房効率を向上させることができる。 - 特許庁
In the case that a temperature increasing gradient becomes approximately constant, the judging segment judges that no frosting is adhered to the evaporator 18 and the operation of the compressor 12 is restarted under a condition in which the detected temperature of the refrigerator temperature sensor 28 becomes higher than the set temperature.例文帳に追加
温度上昇勾配が略一定となる場合は、判定部は蒸発器18に霜が付いていないと判定し、庫内温度センサ28の検出温度が設定温度より高くなった条件で圧縮機12の運転を再開する。 - 特許庁
Therefore, the inner dimension in the vertical direction of a tank body 51 is set to be larger than the equivalent inner diameter to form the gas- liquid separator 50 longer than width in the vertical direction, preventing the liquid-phase refrigerant from being fed to an intake side of a compressor 10 by bubbling.例文帳に追加
このため、タンク本体51の上下方向内寸法を相当内直径より大きくして気液分離器50を縦長として、泡立ちにより液相冷媒が圧縮機10の吸入側に供給されてしまうことを防止できる。 - 特許庁
The gas turbine engine includes a bleeding means 12 provided in a core passage 13, in which stationary blades included in the compressor are disposed, and bleeding air on an upstream side further than a throat part between the most upstream stationary blades 4b1 that is the stationary blades on the most upstream side.例文帳に追加
圧縮機が備える静翼が配置されるコア流路13に設けられ、最も上流側の静翼である最上流静翼4b1同士の間のスロート部よりもさらに上流側にて空気を抽気する抽気手段13を備える。 - 特許庁
This heat pump-type air conditioner 60 is provided with a refrigerating cycle constituted by connecting a compressor 1, a four-way valve 2, an outdoor heat exchanger 6, an expansion valve 10 and an indoor heat exchanger 3 by refrigerant piping, and can execute a cooling operation and a heating/humidifying operation.例文帳に追加
ヒートポンプ式空気調和機60は、圧縮機1、四方弁2、室外熱交換器6、膨張弁10及び室内熱交換器3を冷媒配管で接続して冷凍サイクルを構成し、冷房運転及び暖房加湿運転が可能である。 - 特許庁
The chip compressor 100 comprises: a hopper 1 storing chips; a spiral screw 4 as a chip carrier part formed on the side of the bottom 1b of the hopper 1; and a compression cylinder block 10 compressing the chip carried by the spiral screw 4.例文帳に追加
切り粉圧縮機100は、切り粉を蓄えるホッパ1と、ホッパ1の底1b側に形成された切り粉搬送部としてのスパイラルスクリュー4と、スパイラルスクリュー4により搬送されてきた切り粉を圧縮する圧縮シリンダブロック10とを有している。 - 特許庁
To provide a compressor in a structure capable of controlling self- exciting oscillation generated in an intake valve at the initail stage of gas intake while the degree of blocking for the intake valve is being relaxed, and of letting intake gas be stably and efficiently introduced into a cylinder bore.例文帳に追加
吸入弁の閉塞度合いを緩和してガス吸入初期時に吸入弁に生じる自励振動を抑制でき、吸入ガスのシリンダボア内への流入を安定して効率良く行い得る構造の圧縮機を提供すること。 - 特許庁
In the proportional-integral control, a discharge pressure Pd from a compressor 21 is adjusted to be stably continued for a prescribed time, and the amount of the refrigerant in a refrigerant circuit 10 is determined by using state quantity of the refrigerant flowing in the refrigerant circuit 10.例文帳に追加
このPI制御では、圧縮機21からの吐出圧力Pdが安定して所定時間継続するように調節され、冷媒回路10を流れる冷媒の状態量を用いて、冷媒回路10内の冷媒量を判定する。 - 特許庁
The heated air rising in temperature by heat exchange with the condenser 28 and the compressor 32 flows into the second housing chamber 24 from the first housing chamber 22 through a communication part 26 and then, discharged outside the machine from an exhaust port of the front panel.例文帳に追加
凝縮器28および圧縮機32と熱交換して温度上昇した加温空気は、連通部26を介して第1収納室22から第2収納室24に流入し、その後に前面パネルの排気口から機外に排気される。 - 特許庁
The single screw compressor 1 includes a screw rotor 3 having a plurality of spiral grooves 22 at the periphery of a first rotary shaft 8, and gate rotors 5 and 6 having a plurality of teeth 12 at the periphery of second rotary shafts 8 and 9.例文帳に追加
第1発明のシングルスクリュー圧縮機1は、第1の回転軸8の周囲に複数本の螺旋状の溝22を有するスクリューロータ3と、第2の回転軸8、9の周囲に複数の歯12を有するゲートロータ5、6とを備えている。 - 特許庁
This inverter control compression device includes a hermetic scroll compressor and an inverter control device 400 controlling speed of a motor part 3 and having an inverter secondary side voltage characteristics linearly changing in relation to inverter output frequency.例文帳に追加
インバータ制御圧縮装置は、密閉形スクロール圧縮機と、インバータ出力周波数に対して一次関数的に変化するインバータ二次側電圧特性を有してモータ部3の回転数を制御するインバータ制御装置400とを備える。 - 特許庁
To provide a hermetic reciprocating compressor capable of being stably driven for a long period of time without a piston frictionized/abrased, without producing sludge and without deteriorating refrigerating machine oil even in a case of using an HFC system refrigerant, and a refrigeration unit using it.例文帳に追加
HFC系冷媒を使用した場合でも、ピストンが摩擦・摩耗することがなく、スラッジが発生せず、冷凍機油が劣化せず、長期に亘り安定して運転できる密閉型往復圧縮機およびそれを用いた冷凍装置を提供すること。 - 特許庁
In the desiccant air conditioner using a heat pump, a compressor and a condenser are installed outside the desiccant air conditioner as an outdoor unit, an evaporator coil and a condenser coil are installed in the desiccant air conditioner, and connected to the outdoor unit by piping.例文帳に追加
ヒートポンプ利用のデシカント空調機において、圧縮機及び凝縮器を室外機ユニットとしてデシカント空調機の外部に設置し、デシカント空調機内部にはエバポレーターコイル及びコンデンサーコイルを設置して、室外機ユニットと配管接続する。 - 特許庁
A combined cycle is composed of a gas turbine 8 comprising a generator 1, a compressor 2, a combustor 3, a blade cooling air cooler 4, and a turbine 6; a steam turbine 29 comprising high pressure, middle pressure, and low pressure turbines 21, 22, 13; and an exhaust heat recovery boiler 9.例文帳に追加
発電機1、圧縮機2、燃焼器3、翼冷却空気冷却器4、及びタービン6からなるガスタービン8と、高圧、中圧及び低圧タービン21,22,23からなる蒸気タービン29と、排熱回収ボイラ9とでコンバインドサイクルを構成する。 - 特許庁
At that time, the increasing load of the motor 19 can be reduced and energy saving can be obtained by making the fourth turbo compressor 18 be in unloaded state with a pipe line 36 by closing an operation switching valve 37 and opening an operation switching valve 38.例文帳に追加
このとき、運転切換弁37を閉じ、運転切換弁38を開いて管路36によって第4ターボ圧縮機18をアンロード状態とすることにより、モータ19の負荷の増大を軽減することができ、省エネルギー化を達成することができる。 - 特許庁
This linear compressor is composed of a cylinder 10, the piston 20, the cylinder end surface 11, a movable part 40 and a fixed part 50 for constituting a linear motor part, coil springs 15 and 30, a head cover part 80, a support mechanism part 90, and a sealed vessel 100.例文帳に追加
リニア圧縮機は、シリンダ10と、ピストン20と、シリンダ端面11と、リニアモータ部を構成する可動部40および固定部50と、コイルばね15、30と、ヘッドカバー部80と、支持機構部90と、密閉容器100等から構成される。 - 特許庁
In a controller 50, defrost operation is carried out by switching a first four way selector valve 26 of only an outdoor unit 20A with defrosting request, and communicating a delivery side of a compressor 21 with the outdoor heat exchanger 22 of the outdoor unit 20A with defrosting request.例文帳に追加
コントローラ(50)により、デフロスト要求のあった室外ユニット(20A)のみの第1四路切換弁(26)を切り換え、該デフロスト要求のあった該室外ユニット(20A)の室外熱交換器(22)と圧縮機(21)の吐出側とを連通してデフロスト運転を実行する。 - 特許庁
In the refrigerator, a motor 40 for a compressor is connected to input terminals (a), (b) connected to a commercial power source through first feeder lines 41a, 41b, and a rectifier 31 and an inverter 32 are respectively connected to the lines 41a, 41b.例文帳に追加
本発明に係る冷蔵装置においては、商用電源に接続された入力端子a、bに、第1給電路41a、41bを介してコンプレッサ用モータ40が接続され、第1給電路41a、41bに、整流回路31及びインバータ回路32が接続されている。 - 特許庁
The thermoelectric device 25a is installed in a place at high temperature, for example, near the compressor 24a, and if electric power shutoff to the outdoor unit 2a occurs, the outdoor unit control part 20a drives it by a voltage generated by the thermoelectric device 25a.例文帳に追加
熱電素子25aは、例えば、圧縮機24aの近傍のような高温となる場所に設置されており、室外機2aへの電力遮断が発生した場合には、熱電素子25aで発電した電圧で室外機制御部20aが駆動する。 - 特許庁
When the value detected by the current sensor 12 is larger than a preset value A and the value detected by the pressure sensor 19 is a preset value C or larger, a control device 14 instructs a capacity control device 17 to reduce the capacity of the screw compressor 2.例文帳に追加
制御装置14は、電流センサ12の検出値が所定値Aよりも大きく、また、圧力センサ19の検出値が所定値C以上である場合、容量制御装置17に命じてスクリュー圧縮機2の容量を低減させる。 - 特許庁
Furthermore, the number of revolutions of a compressor is determined in accordance with an absolute value of a difference between room temperature and set temperature set in advance (ST4 or ST12), and operation in the determined mode is performed during time of a second timer set in accordance with the outside air temperature.例文帳に追加
さらに、室温と予め設定した設定温度の差の絶対値に応じて圧縮機の回転数を決定し(ST4ないしST12)、その決定モードでの運転を外気温度に応じて設定した第2のタイマの時間だけ行う。 - 特許庁
The compressor with the transmission comprises a housing 10, a compression mechanism 40 constructed in the housing 10 for compressing a refrigerant and a friction type transmission mechanism 301 constructed in the housing for speed-variably driving the compression mechanism 40.例文帳に追加
この変速機付き圧縮機は、ハウジング10と、ハウジング10内に構成されて冷媒を圧縮可能な圧縮機構40と、ハウジング10内に構成されて圧縮機構40を変速して駆動可能な摩擦式変速機構301とを備えている。 - 特許庁
To provide a manufacturing method of a sealed motor compressor capable of accurately fixing an inner part for a container body in a coaxial state even in the case that an outer diameter of the inner part to be welded to the container body is shorter than an inner diameter of the container body.例文帳に追加
容器本体の内径よりも外径の小さい内部部品を容器本体に溶接する場合でも、内部部品を容器本体に対して精度よく同軸状に固定することのできる密閉型電動圧縮機の製造方法を提供する。 - 特許庁
This scroll compressor includes: a crank pin 64 integrally formed as a crankshaft 62 of a rotary driving shaft 6 on a main shaft 61; and a bush 65 removably fitted to the crank pin 64, wherein the crank pin 64 and the bush 54 are fixed through a fixing pin 7.例文帳に追加
回転駆動軸6のクランク軸62として主軸61に一体成型されたクランクピン64と、クランクピン65に対して着脱自在に取り付けられるブッシュ65とを有し、クランクピン64とブッシュ65とを固定ピン7を介して固定する。 - 特許庁
The side expansion oil passages 22 extend to the position on the end oil passage 13 side on the compressor side from a line segment to connect an upper end (point A) of the end oil passage 12 on the turbine side to a center part (point B) of a discharge port 15 over the entire height direction.例文帳に追加
側方拡張油路22は、高さ方向の全体にわたって、タービン側の端部油路12の上端部(A点)と、排出口15の中心部(B点)とを結ぶ線分よりも、コンプレッサ側の端部油路13側の位置まで延びている。 - 特許庁
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|