| 例文 |
current terminalの部分一致の例文一覧と使い方
該当件数 : 4341件
During current measurement with a CTT plug into a CTT terminal, for example, when a break occurs in a wiring, a high voltage occurs between both electrodes of CTT plug, discharge occurs in a discharge gap 16 of a CT secondary opening protection circuit 1, a discharge current flows through a fuse 21, and a fuse 21 is burnt.例文帳に追加
CTTプラグをCTTターミナルに挿入した状態で、電流計測中に、例えば、配線に断線が発生すると、CTTプラグ両極間に高電圧が発生し、CT2次側開放保護回路1の放電ギャップ16において放電が発生し、ヒューズ21に放電電流が流れ、ヒューズ21が切れる。 - 特許庁
A touch panel control circuit is provided for selecting one of two to four numbers of electrode terminals from among the plurality of electrode terminal 102 of the detection transparent conductive film 101, applying an AC signal provided from a signal source 105 through a current detection resistor (r) 103, and then detecting a current that flows through each of the selected electrode terminals.例文帳に追加
この検出用透明導電膜101の複数の電極端子102から4端子乃至2端子を選択し、電流検出抵抗(r)103を介して信号現105から交流信号を印加し、該選択した電極端子に流れる電流を検出するタッチパネル制御回路を設ける。 - 特許庁
Both passive and active parts (21, 22) for constituting the circuit in which an electric current flows are arranged in the interior of a resin mold member 40 wired to constitute a loop circuit of an electric current path and implemented on the printed-circuit board 31 making use of connection-terminal members 41 protruded from the resin mold member 40.例文帳に追加
電流が流れる回路を構成するための受動部品と能動部品(21,22)の両方が、樹脂モールド材40の内部に電流経路としてループ回路を構成する配線を施した状態で配置され、樹脂モールド材40から突出する接続用端子41を用いてプリント基板31に実装されている。 - 特許庁
Shield wiring 21 is provided between the wiring of a current output terminal of a TFT 20a constituting an optical sensor 20 and COM wiring 14a, and the potential of the shield wiring 21 is fixed to predetermined potential so that a potential difference between the current output wiring and the COM wiring 14a is not varied with time.例文帳に追加
光センサ20を構成するTFT20aの電流出力端子の配線とCOM配線14aとの間にシールド配線21を設け、電流出力配線とCOM配線14aとの間の電位差が時間的に変動しないように、シールド配線21の電位を所定電位に固定しておく。 - 特許庁
A switching circuit 9 connected with a control signal input terminal (DTC) for dead time control of a control circuit 4 sets a short minimum off time of a switching transistor Q1 when a load current IL is flowing and sets a long minimum off time when the load current IL is not flowing.例文帳に追加
制御回路4のデッドタイムコントロールのための制御信号入力端子(DTC)に接続した切替回路9によって、負荷電流ILが流れている期間にはスイッチングトランジスタQ1の最小オフ期間を短く設定し、負荷電流ILが流れない期間には最小オフ期間を長く設定する。 - 特許庁
The charger 101 identifies the kind of a battery pack 131 on the basis of a voltage unique to the battery pack 131 to be supplied to a terminal 129 for communication (D), and determines a charging power value so that the maximum charging current of the identified battery pack may be the maximum value of the charging current in the constant power charging.例文帳に追加
充電装置101では、通信(D)端子129に供給されるバッテリーパック131固有の電圧に基づいてバッテリーパックの種類を識別し、識別したバッテリーパックの最大充電電流が定電力充電における充電電流の最大値になるように充電電力値を決定する。 - 特許庁
When a signal indicating the drop of the power supply voltage is outputted from the power supply voltage detection circuit 68, a voltage switch circuit 69 makes a voltage signal outputted to the ECU from the output terminal 41 to a high voltage side or a low voltage side according to the direction of the current detected by the current detection circuit 67.例文帳に追加
電源電圧が低下したことを示す信号が電源電圧検出回路68から出力されると、電圧切替回路69は、出力端子41からECUに出力される電圧信号を電流検出回路67の検出した電流の向きに応じて高電圧側又は低電圧側にする。 - 特許庁
To provide a power supply circuit that does not require a current share circuit having a complicated configuration when a plurality of DC/DC converters are connected in parallel to a common DC input power supply and a common DC output terminal and current sharing between the respective DC/DC converters during parallel operation is equalized.例文帳に追加
共通直流入力電源かつ共通直流出力端子に複数個のDC/DCコンバータを並列接続し、並列運転時の各DC/DCコンバータ間の電流分担を均等にする場合、構成が複雑であるカレントシェア回路を必要としない電源回路を提供することを目的とする。 - 特許庁
The one end of the secondary side winding 126B of a boosting/smoothing rectifier circuit 126 is connected to a ground line through a current measuring resistance 132, and a detection signal S3 in accordance with the terminal voltage Vd of the current measuring resistance 132 is captured in an A/D port 123C of a PWM control circuit 123.例文帳に追加
昇圧・平滑整流回路126の2次側巻線126Bの他端は、電流測定用抵抗132を介してグランドラインに接続され、この電流測定用抵抗132の端子電圧Vdに応じた検出信号S3が、PWM制御回路123のA/Dポート123Cに取り込まれる。 - 特許庁
When the information providing server receives the information providing request signal (S11: Yes), it acquires information about means of transportation available for a travel from the current position to the destination based on the current position information and the destination information included in the information providing request signal (S12) and transmits it to the portable terminal device (S13).例文帳に追加
情報提供サーバは、情報提供要求信号を受信すると(S11:Yes)、情報提供要求信号に含まれている現在位置情報及び目的地情報を基に、現在位置から目的地に移動するために利用可能な交通機関に関する情報を取得し(S12)、携帯端末装置に送信する(S13)。 - 特許庁
The portable terminal 2 is configured to store a map of the area A therein, display the map and be operable for a user to select a destination B9 described on the map, displays the positional information transmitted from the IC chip 1 on the map as a current place and displays routing from the current place to the selected destination.例文帳に追加
携帯用端末機2は、エリアAの地図が記憶され地図を表示して地図に記載された行先B9を選択操作することができるものであってICチップ1から送信された位置情報を地図上に現在地として表示するとともに現在地から選択された行先までの道順を表示する。 - 特許庁
A Web server providing the transfer guidance service calculates the travel time from the current position of the portable terminal to the starting station by using the positional information and informs the user by what time the user should leave the current position to catch a specified train by taking the calculated travel time into consideration.例文帳に追加
乗り換え案内サービスを提供するWebサーバは、その位置情報を用いて携帯端末の現在位置から出発駅までの移動時間を算出し、算出されたその移動時間を考慮して、指定された電車に乗車するためには現在位置を何時までに出発しなければならないかをユーザに提供する。 - 特許庁
To provide an induction heating device which excites an induction current to a heating object and induction heats, in which an accidental disconnection due to a connection and disconnection stress of a regular current of a fuse is eliminated and damages of a circuit inner than a trigger terminal of a switching element is reduced even at the time of a short circuit failure of the switching element.例文帳に追加
加熱対象に誘導電流を誘起し誘導加熱するように構成した誘導加熱装置において、ヒューズの定常電流の断続ストレスによる偶発的断線をなくし、かつスイッチング素子の短絡故障時にも、スイッチング素子のトリガ端子よりも内部の回路の損傷を低減する。 - 特許庁
A capacitor C13 of which one terminal is connected to a connecting point of output terminals of first and second voltage/current converters 11, 12 of a driving apparatus is controlled by a regulator 50 in sucking or supplying a current on the basis of a result of comparison between an output voltage VOF of an amplifier 14 and a reference voltage (VrefB, VrefC).例文帳に追加
駆動装置の第1,第2の電圧電流変換器11,12の出力端の接続点に一端を接続したコンデンサC13に対して、調整器50が増幅器14の出力電圧VOFと参照電圧(VerfB,VrefC)との比較結果に基づき電流を吸引あるいは供給の制御を行う。 - 特許庁
This consists of the master receptacle which has an alarm to be actuated when the working current exceeds the tolerable current value of the cord for the electric power supply, which has its reset button, and which has a plug receiver with some plug ports, and consists of a daughter receptacle which has some plug ports and a plug terminal and the plug receiver for the next stage together as a set.例文帳に追加
本発明は、使用電流が電源コードの耐用電流を超える際に作動されるアラームとそのリセットボタン、および幾つかの差し込み口を有するプラグ受けを有する親コンセントと、幾つかの差し込み口を有すると共にプラグ端子と次段のためのプラグ受けを有する子コンセントとをセットとする。 - 特許庁
The display device includes: a light-emitting element where electric current flows when a voltage that exceeds a threshold value is applied thereto and which emits light in brightness corresponding to the electric current; a driving circuit that drives the light-emitting element; wiring that supplies the voltage and an electrical signal to the driving circuit; and a terminal for connecting the wiring with an external circuit.例文帳に追加
表示装置は、しきい値を越える電圧を印加したときに電流が流れ、該電流に応じた明るさで発光する発光素子と、該発光素子を駆動する駆動回路と、該駆動回路に電圧及び電気信号を供給する配線と、該配線を外部回路に接続するための端子とを有する。 - 特許庁
An NPN transistor 4 is provided where a base is connected to an input side of a current amplifier circuit 2 which amplifies an input current to supply it to the base of a transistor 3 at an output stage, an emitter is connected to a ground, and a collector is connected to an output terminal OUT, with a structure comprising a parasitic PNP transistor 5.例文帳に追加
入力電流を増幅して出力段のトランジスタ3のベースに供給する電流増幅回路2の入力側にベースが、エミッタがグランドに、コレクタが出力端子OUTにそれぞれ接続されたNPN型のトランジスタ4を設けるとともに、このトランジスタ4をPNP型のトランジスタ5が寄生する構造とする。 - 特許庁
The peak detection circuit comprises a first transistor, connected between a power supply potential and an output terminal, an amplifier for driving the first transistor, based on the difference between an input signal and an output signal, a second transistor connected to the first transistor, a third transistor current-mirror-connected to the second transistor, and a current source for setting a current value flowing in the third transistor.例文帳に追加
ピーク検波回路は、電源電位と出力端子の間に接続された第1のトランジスタと、入力信号と出力信号の差に基づいて、前記第1のトランジスタを駆動する増幅器と、前記第1のトランジスタに接続された第2のトランジスタと、前記第2のトランジスタにカレントミラー接続された第3のトランジスタと、前記第3のトランジスタに流れる電流値を設定する電流源とを有する。 - 特許庁
This bias circuit is provided with: a voltage stabilizing part connected from a control voltage input terminal through a current limiting resistance to a ground potential; an emitter follower for bias supply whose base is connected through the resistance to a node between the current limiting resistance and the voltage stabilizing part; and a current limiting part connected between the base and emitter of the emitter follower for bias supply.例文帳に追加
本発明のバイアス回路は、制御電圧入力端子から電流制限抵抗を介して接地電位との間に接続される電圧安定部と、前記電流制限抵抗と電圧安定部の間のノードと抵抗を介しベースが接続されるバイアス供給用エミッタフォロワと、前記バイアス供給用エミッタフォロワのベースとエミッタの間に接続される前記電流制限部とを有している。 - 特許庁
The power generation controller for controlling the generator output to a set value by controlling the exciting winding of an AC generator for vehicle intermittently comprises means for detecting an exciting current, means for receiving a signal for regulating the exciting current detection level from an external terminal, and means for regulating the exciting current detection level upon receiving the regulation signal.例文帳に追加
車両用交流発電機の励磁巻線を断続制御して発電機出力を設定値に制御する発電制御装置において、励磁電流を検出する手段と、外部端子から該励磁電流検出レベルを調整する励磁電流検出調整信号を受信する手段と該調整信号を受信した時に該励磁電流検出レベルを調整する手段とを有することを特徴としている。 - 特許庁
The mobile terminal device controls each charger so that charging is performed with a charging current value stored in advance, when a plurality of chargers are connected, or performs charging using one of a plurality of the chargers, or controls the charging current value that is outputted from a plurality of the chargers according to the detected charging current values of the plurality of the chargers.例文帳に追加
本発明にかかる携帯端末装置は、複数の充電部が接続されているとき、予め記憶した充電電流値で充電を行うように各充電部を制御、または前記複数の充電部のうちの1つを用いて充電を行うように制御、または検出した前記複数の充電部の充電電流値に応じて前記複数の充電部から出力される充電電流値を制御する。 - 特許庁
To provide a service management program and methods for hotel facilities, which enable a hotel to render the best services to hotel customers without a wait of several minutes when they arrive the hotel by ascertaining always current service data of the hotel facilities at a registration terminal that is a part of the hotel facilities.例文帳に追加
ホテル施設のレジ端末において、レジで常に施設の現在のサービスの情報が把握でき、宿泊客の来店に際して、顧客を待たせることなく最適なサービスを提供できるようにする。 - 特許庁
When the power terminal is positioned in a predetermined location, a calculation means 4 calculates the amount of noise occurring in each different signal line, on the basis of the current path specified by the path specification means 3.例文帳に追加
算出手段4は、所定の配置箇所に電源端子を配置した場合に、経路特定手段3によって特定された電流経路に応じて他の各信号配線に発生するノイズの量をそれぞれ算出する。 - 特許庁
In a terminal housing hole 8 for the second housing 7, a plurality of second male connection terminals 10 with current capacity less than that of the first connection terminals 6 and having a wire 9 connected at the rear end are housed.例文帳に追加
第2のハウジング7の端子収容孔8には、第1の接続端子6よりも電流容量が小さく電線9を後端に接続した複数個の雄型の第2の接続端子10が収納されている。 - 特許庁
When the inter-terminal voltage Vc is lower than the lower limit value in a voltage range generating no inrush current, an engine ENG is started with the battery B, and then a target engine rotational speed is decided to drive the engine ENG.例文帳に追加
端子間電圧Vcが突入電流を生じない電圧範囲の下限値を下回るときには、バッテリBを用いてエンジンENGを始動させた後、目標エンジン回転数を決定してエンジンENGを駆動する。 - 特許庁
To solve the matter of an emergency call terminal that the positional information cannot be obtained by utilizing the global positioning system, and to obtain the current outline position precisely even if the installation position of a wireless base station is unknown.例文帳に追加
緊急情報端末において、衛星測位システムを利用して位置情報を得ることができず、且つ無線基地局の設置位置が不明であっても、現在の概略位置を精度良く得ることを可能にする。 - 特許庁
The negative electrode 2b is connected to a third conductive layer 9 through the intermediary of the conductive adhesive agent 8, and a current collector 9 is connected to a connection terminal 10, extending between the casing 1a and the lid 1b.例文帳に追加
負極2bは、導電性接着剤8を介して第3導電層9と接続されており、集電体9は、収容部1aと蓋1bとの間に延伸して接続端子10と接続している。 - 特許庁
To provide a sealed battery in which a welding between a current collector and an external terminal fixed on a core body of an electrode body can easily be performed by a high energy beam, such as laser or the like and provide its manufacturing method.例文帳に追加
電極体の芯体に取り付けられた集電体と外部端子との間の溶接を、レーザ等の高エネルギー線により容易に溶接できるようにした密閉電池及びその製造方法を提供する。 - 特許庁
In the case where a current flowing between the inner core 5 and the terminal 6 via the conductive ink 2 can be measured by the measurement instrument 9, it is determined that the conductive ink 2 properly adheres to the semiconductor wafer 7.例文帳に追加
導電性インク2を介して中芯5と端子6との間に流れる電流が測定器9により測定された場合に、半導体ウェハ7上に導電性インク2が正しく付着したと判定する。 - 特許庁
The negative ion generator 21 electrically connected between the insertion holes 24 and the terminal pins 25, and driven by extracting the current flowing to the terminals of the fluorescent lamp 10 is built in the housing 20.例文帳に追加
上記ハウジング20の内部には上記挿入孔24と端子ピン25の間に電気的に接続されており、蛍光ランプ10の端子に流れる電流を引き出して駆動する陰イオン発生器21を内蔵する。 - 特許庁
The bases of the TRs Q4, Q8 which are the components of a constant current circuit are connected to a gain changeover circuit 3, one is active and the other is inactive, in response to a signal received from an external control terminal 4.例文帳に追加
定電流回路を構成するトランジスタQ4、Q8のベースは利得切替回路3に接続し、外部制御端子4より入力される信号に応じて一方を動作状態、他方を停止状態とする。 - 特許庁
Data of voltages Vbi=Vi-Vi-1 of respective cells Bi are obtained in time series from terminal voltages Vi (i=1, 2,,,n) of the respective cells Bi (i=1, 2,,,n) while discharging discharge current I from the storage battery B.例文帳に追加
蓄電池Bから放電電流Iを放電させながら、蓄電池Bの各セルBi (i=1、2…n)の端子電圧Vi (i=1、2…n)から、各セルBi の電圧Vbi=Vi −Vi-1 のデータを時系列的に採取する。 - 特許庁
Each inspection terminal 14 is pressure contacted in the contactable and releasable state with each of the plural electronic part terminals 8 provided on the electronic part 1, and a current can be conducted between the electronic part terminals 8 and the inspection terminals 14.例文帳に追加
電子部品1が備える複数の各電子部品用端子8に各検査用端子14が接離自在に圧接して、これら電子部品用端子8と検査用端子14との間で電流が導通可能とされる。 - 特許庁
A buffer 23 which is connected in the line from a main control CPU 1 that undergoes the energy saving control to a power-on CPU 15 consists of CMOSIC, etc., that has the reduced current leaked from an input terminal and also has the hysteresis characteristic.例文帳に追加
省エネ制御されるメイン制御用CPU1から電源オンCPU15へのバッファ23を、入力端子からのリーク電流の少ない、かつヒステリシス特性を持たせたCMOSICなで構成する。 - 特許庁
To provide a battery in which a contact state of a current collector and a terminal is stabilized, contact failure is suppressed when an impact due to a fall or the like is added, and which is superior in quality and shield property of a case.例文帳に追加
集電体と端子との接触状態が安定化し、落下等の衝撃が加わった場合に接触不良が生じるのが抑制され、品質及びケースの密閉性が良好である電池を提供する。 - 特許庁
The battery 2 includes the current interrupting mechanism 4 which interrupts the conduction of the electrode body 80 to the outside of the battery by disrupting a conductive path connecting at least one of the electrodes to an external terminal 30.例文帳に追加
電池2は、上記電極の少なくとも一方と外部端子30とを結ぶ導電経路を分断することによって電極体80と電池外部との導通を遮断する電流遮断機構4を備える。 - 特許庁
The main current path (drain-source or collector-emitter) of a transistor 12 for clamping voltage is connected in series with the output terminal 9 of the driving IC 1, and a specified voltage is applied to the control electrode (gate or base).例文帳に追加
駆動用IC1の出力端子9に、電圧クランプ用トランジスタ12の主電流路(ドレイン−ソース又はコレクタ−エミッタ)を直列接続し、その制御電極(ゲート又はベース)に所定電圧を印加する。 - 特許庁
To provide an analog output terminal unit capable of respectively corresponding to voltage control type and current control type external apparatuses, and capable of achieving size reduction of the unit and low power consumption.例文帳に追加
本発明は、電圧制御型及び電流制御型それぞれの外部機器に対応可能であるとともに、装置の小型化及び低消費電力化が実現できるアナログ出力端末器を提案することを目的とする。 - 特許庁
This device has a structure wherein an input path 777 of the ion current is connected to an input terminal 13C of the transistor amplifying circuit, and a detection electrode 7 is connected in the open form in the branched shape from the input path.例文帳に追加
そして、このトランジスタ増幅回路の入力端子13Cにイオン電流の入力経路777を接続し、さらに入力経路から分岐する形で検知電極7を開放形態で接続した構造とする。 - 特許庁
The two current sources are configured to be selectively connected, in a second step and at the second temperature, to the offset-control terminal(s) (130) of the input stage (120), and thereby to trim the output of the input stage.例文帳に追加
2つの電流源は、第2工程において第2の温度で入力ステージ(120)のオフセット制御端子(単数または複数)(130)へ選択的に接続されて、それによって入力ステージの出力がトリミングされる。 - 特許庁
A mobile terminal 20 within the reach of electric waves from the theft detector 10 receives the theft signal and transmits a theft detection mail including the individual identification number and the current positional information to a management server 60.例文帳に追加
盗難検知装置10の電波の届く範囲内にある移動体端末20は、盗難信号を受信し、個体識別番号と現在位置情報とを含む盗難検出メールを管理サーバ60へ送信する。 - 特許庁
After the metal fuse 12 is blown, the diode 20 regulates the current flow, and the potential at the input of the inverter gate 18 is made to hold at H-level, no matter what the test fuse terminal 14 level may be.例文帳に追加
メタルヒューズ12の切断後には、ダイオード20によって電流の通電が規制されるので、テストヒューズ端子14がどのようなレベルであってもインバータゲート18の入力端子側の電位がHレベルに維持される。 - 特許庁
Even if an abnormal signal is inputted to the input terminal of the buffer 23 immediately after the input of the power supply, the buffer 23 outputs a high output voltage to turn off the switching transistor 12, so that a rush current is not caused to flow.例文帳に追加
電源投入直後において、バッファ23の入力端子に異常な信号が入力しても、バッファ23はハイの出力電圧を出力してスイッチトランジスタ12をオフさせるので、ラッシュカレントが流れない。 - 特許庁
The measurement means 22 for the storage battery uses data previously computed for calculating a residual capacity and relationship between the measured discharge current value and a terminal voltage to calculates the residual capacity.例文帳に追加
蓄電池の残存容量の測定手段22は、事前に算出された残存容量算出のためのデータを用いて、測定した放電電流値と端子電圧の関係を用いて、残存容量を算出する。 - 特許庁
The navigation device sets the location sent from the information terminal 101 as the destination, and searches the route from the current location to the destination, and performs the navigation guidance.例文帳に追加
ナビゲーション装置は、情報端末101から送信された住所情報に基づく位置を目的地として設定し、GPSユニットが取得した現在位置から目的地に至るルートを検索してナビゲーションを実行する。 - 特許庁
An output of a buffer amplifier 19 is connected to a control terminal of the first switching element 13 for controlling the supply current of the LED series connection circuit, while an output of a multiplexer 20 is connected to an input of the buffer amplifier.例文帳に追加
そして、LED直列接続回路の通電電流を制御する第1スイッチング素子13の制御端子に、バッファアンプ19の出力を、該バッファアンプの入力にマルチプレクサ20の出力を接続する。 - 特許庁
To surely prevent a current reverse flow to the side of an element for charging at charge while charging a capacitor sufficiently to the voltage appearing at a specified terminal, concerning a charge circuit.例文帳に追加
本発明は、充電回路に関し、所定の端子に現れている電圧までコンデンサを十分に充電しつつ、放電時には充電用の素子側への電流逆流を確実に防止することを目的とする。 - 特許庁
To provide a temperature control device, capable of achieving all superior voltage variation, noise terminal voltage and harmonics current properties, and to provide an image forming apparatus including the temperature control device.例文帳に追加
電圧変動特性、雑音端子電圧特性および高調波電流特性のすべてにおいて良好な特性を得ることができる温度制御装置および該装置を備えた画像形成装置を提供する。 - 特許庁
The state detection sensor 50 is a sensor for detecting a current state of the mobile phone terminal 1 and employs, for example, an angle sensor which detects a relative angle formed by first and second housings around X axis.例文帳に追加
形態検出センサ50は、携帯電話端末1の形態を検出するセンサであり、例えば、第1の筐体と第2の筐体のX軸回りの相対的な角度を検出する角度センサを用いる。 - 特許庁
In the bus bar 12, the first bus bar 15 with a male terminal joint 14 requiring a spring property constitutes the bus bar body, and the second bus bar 16 is joined in a position that requires a large current flow in the first bus bar 15.例文帳に追加
バスバー12は、バネ性を必要とする雄端子接続部14を有する第一バスバー15をバスバー本体とし、この第一バスバー15における大電流を流す必要のある位置に第二バスバー16を接合する。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|