| 意味 | 例文 |
current valueの部分一致の例文一覧と使い方
該当件数 : 12431件
A landmark-to-landmark transition instructions reproducing part 10 regards the value of the current position vicinity landmark storage part 8 as a starting point landmark, regards the value of the destination vicinity landmark storage part 9 as a destination landmark, and fetches instructions from a landmark-to-landmark transition instructions storage part 2 to reproduce the instructions to a driver.例文帳に追加
ランドマーク間移動説明文再生部10は現在地近隣ランドマーク格納部8の値を出発点ランドマークとみなし、目的地近隣ランドマーク格納部9の値を目的地ランドマークとみなしてその説明文をランドマーク間移動説明文格納部2から取出し、運転者に対して再生する。 - 特許庁
The voltage control circuit 8 of a DC chopper type quick charging circuit calculates the changes of quick charging voltage by the capacity fluctuations of the capacitor 7 from the measured temperature value of the capacitor itself or the ambient measured temperature value to correct the fluctuations of the calculated capacitance C by control of output current i.例文帳に追加
直流チョッパ型の急速充電回路の電圧制御回路8は、コンデンサ7の容量変動による急速充電電圧の変化を、コンデンサ自体の温度計測値、または周囲の温度計測値から算出し、この算出したコンデンサ容量Cの変動に出力電流iの制御で補正する。 - 特許庁
On the other hand, by multiplying what a demand for a known brake lamp WBRK is added to the current demand VEL for the accessories by a preset idle stop continuous time target value TISTP, a battery demand estimation integrated value WCON during idle stop is estimated (Step S25).例文帳に追加
一方、補機類の現時点の消費電力VELに既知のブレーキランプの消費電力WBRKを加算したものに、予め設定したアイドル停止継続時間目標値TISTPを乗算することにより、アイドル停止中のバッテリ消費電力推定積算値WCONを推定する(ステップS25)。 - 特許庁
In the device 48, when an electrostatic voltage of the battery 47 satisfies a first prescribed value, an electric current is passed under a pulse load at a constant duty ratio, and the residual capacity of the battery is determined, for example, by comparing a voltage measurement value Vp in this case with second and third prescribed values.例文帳に追加
またバッテリ残留容量検知装置48ではバッテリ47の静動電圧が第1の所定値を満たしたときに一定のデューティ比のパルス負荷をかけて通電し、このときの電圧測定値Vpと第2及び第3の所定値とを比較することなどにより、バッテリ残留容量を判定する。 - 特許庁
A torque compensation quantity ΔT2 together with a load compensation quantity ΔT1 are added to a theoretical torque command value T0* at the restart to obtain a final torque command value T1*, and on the basis of it, a motor current is controlled to make torque compensation corresponding to the car load W and the residual tension of the rope 3.例文帳に追加
再スタート時の理論上のトルク指令値T_0 * に対して荷重補償量ΔT_1 と共にトルク補償量ΔT_2 を加算した最終トルク指令値T_1 * を求め、これに基づいてモータ電流を制御することにより、かご荷重Wとロープ3の残留張力に対応したトルク補償を行う。 - 特許庁
The period for feeding the water is computed from the total electrolytic current capacity I inputted from the section 30, the measured value PV_a measured by the section 48 and the set value SV_a of the prescribed concentration of the hydrochloric acid and the water is fed to the electrolytic treatment liquid from the section 49 at every period for feeding the water.例文帳に追加
電解電源部30から入力される総電解電流量Iと、塩化アルミニウム測定部48により測定された測定値PV_a と、所定の塩化アルミニウム濃度の設定値SV_a とから水投入周期を演算し、水投入周期毎に水投入部49から水を電解処理液に投入する。 - 特許庁
A metering unit 100 comprises a measurement instrument 132 for measuring a measured value indicating the characteristics of electric power corresponding to either voltage or current, a CPU 200 for creating a group of information including information indicating the characteristics of electric power and information indicating the measured value, and a PHS card 218 for transmitting the group of information.例文帳に追加
計量ユニット100は、電圧および電流のいずれかに対応する、電力の性質を表す計測値を計測する計測器132と、電力の性質を表す情報、および計測値を表す情報を含む、情報のグループを作成するCPU200と、情報のグループを送信するPHSカード218とを含む。 - 特許庁
A featured value frame memory 201 is formed as a storage area arranged for each partial area of a reference frame being a temporally previous frame with respect to a current frame, and the storage of pixel position information indicating the position of the reference pixel of the reference frame in the storage area designated by an address corresponding to the featured value of the reference pixel is controlled.例文帳に追加
特徴量フレームメモリ201は、カレントフレームに対して時間的に前のフレームである参照フレームの一部の領域毎に設けられた記憶領域であって、参照フレームの参照画素の特徴量に対応するアドレスで指定されるものへの、参照画素の位置を示す画素位置情報の記憶を制御する。 - 特許庁
When a divergence amount δ2 between the detent rotation position θ_n calculated by the current learning value and an initial detent rotation position θ_0 at factory shipment is large (δ2≥determination value A2), it is determined that any abnormality occurs and learning is stopped (ST5, ST8), so as to prevent learning failure outside a tolerance of time degradation.例文帳に追加
また、現在学習値により算出されるディテント回転位置θ_nと工場出荷時の初期ディテント回転位置θ_0との乖離量δ2が大きい場合(δ2≧判定値A2)、何らかの異常が発生していると判断して学習を中止することで(ST5,ST8)、経時劣化の許容範囲外での誤った学習を防止する。 - 特許庁
A vehicle speed sensor 15 is connected to a controller C and the controller controls a solenoid current command value SI such that an opening of a variable orifice becomes small when a vehicle speed signal Sv from the vehicle speed sensor is zero or at a set very low speed area and a steering angle speed signal Sω is zero or a value near to it.例文帳に追加
コントローラCには車速センサ15を接続する一方、コントローラは、車速センサからの車速信号Svがゼロまたは設定極微速域にあり、かつ、操舵角速度信号Sωがゼロまたはそれに近い値のとき、可変オリフィスの開度が小さくなるようにソレノイド電流指令値SIを制御する構成にしている。 - 特許庁
Even if the temperature of the fuel cell is not in the prescribed temperature 1 or more (S430, No), when the temperature of the fuel cell is in the prescribed temperature 2 or more and a current integrated value from the starting is in the prescribed value 3 or more (S440, Yes), water in the anode passage is judged to be generated (S460).例文帳に追加
また、燃料電池の温度が所定値1以上でない場合であっても(S430、No)、燃料電池の温度が所定値2以上、かつ、起動時からの電流積算値が所定値3以上である場合には(S440、Yes)、アノード流路内に水分が発生していると判断する(S460)。 - 特許庁
When the detected load value is smaller than an adult determining threshold and a seat belt is switched into a wear condition from a non-wear condition when comparing the execution time of a routine for determining an occupant at a previous time with a current seat belt wear condition, the CPU changes the value of the non-adult determining flag to "1".例文帳に追加
検出荷重値が大人判定しきい値より小さく、且つ、前回の乗員判定のルーチンの実行時と、現在とのシートベルトの装着状態を比べて、シートベルトが非装着状態から装着状態に切り替わっている場合、CPUは、非大人判定フラグflagの値を「1」に変更する。 - 特許庁
The inductance Lr of a reactor L1 for resonance of a converter circuit part 1 and the capacitance Cr of a capacitor C1 for resonance are already known, and when each value Lr and Cr is settled, the cycle Tn of a resonance current and the property impedance Zn are settled, so each value Tn and Zn is stored in advance in the memory of a control circuit 3.例文帳に追加
コンバータ回路部1の共振用リアクトルL1のインダクタンスLrおよび共振用コンデンサC1のキャパシタンスCrは既知で、各値Lr,Crが決まると共振電流の周期Tnおよび特性インピーダンスZnが決まるので、制御回路3のメモリに、各値Tn,Znを予め格納しておく。 - 特許庁
In the case that the working machine is shifted from a drive standby state to a normal drive state (time T0), a current value of remaining battery power is sequentially determined on the basis of the initial value β1 of remaining battery power determined on the basis of the remaining battery power data A until the working machine shifts to an idle drive state at time T51.例文帳に追加
作業機械が駆動待機状態から通常駆動状態に遷移された場合(時刻T0)には、時刻T51で作業機械がアイドル駆動状態に遷移するまで、バッテリ残量データAより求められたバッテリ残量の初期値β1を基準として、順次バッテリ残量の今回値を求める。 - 特許庁
In the method for adjusting a slip amount of the torque converter 1 based on a target value sw when connecting the lock-up clutch 20, the target value sw is set continuously depending on time within a connection period of time and taking a current input moment E at each time applied on the torque converter 1 into account.例文帳に追加
ロックアップクラッチ20の接続の際に、トルクコンバータ1のスリップ量が目標値swに基づいて調整される方法において、目標値swを接続期間内で連続的に時間に依存させて、トルクコンバータ1に加えられるそのつどの目下の入力モーメントEを考慮して設定する。 - 特許庁
Then the CPU detects the mean value (voltage Va) of the detection voltage Vs, finds as the distortion quantity of the transmit signal the ratio (Vp/Va) of the mean voltage Va and peak voltage Vp, and controls the electric power (current) supplied to the power amplifier so that the distortion quantity is restricted to a specific range around a prescribed value.例文帳に追加
そして、CPUでは、検波電圧Vsの平均値(電圧)Vaを検出し、この平均電圧Vaとピーク電圧Vpとの比(Vp/Va)を、送信信号の歪量として求め、この歪量が規定値を中心とする所定範囲内になるよう、パワーアンプへの供給電力(電流)を制御する。 - 特許庁
Then, it computes a temperature rise ΔT, using both of those average current I and the average rotational speed R (S5), and compares the temperature rise ΔT with a set value Tmax (S6), and when the temperature rise ΔT is larger than a set value Tmax (S6: Y), it stops the drive of a servo motor (S7).例文帳に追加
そして、それら平均電流値I及び平均回転速度Rの双方を用いて温度上昇値ΔTを算出し(S5)、その温度上昇値ΔTを設定値Tmax と比較し(S6)、温度上昇値ΔTが設定値Tmax よりも大きいときに(S6;Y)、サーボモータの駆動を停止させる(S7)。 - 特許庁
In the method for determining a drive current value for a laser light source, first, light for data erasing having a light intensity, which is larger than a power level of a first light intensity and smaller than a power level of a third light intensity, is continuously projected onto a region where trial writing for determining an optimum value of the third light intensity is performed.例文帳に追加
本発明のレーザ光源駆動電流値決定方法では、先ず第3の光量の最適値を決定するための試し書きを行う領域に対して第1の光量のパワーレベルよりは大きく、第3の光量のパワーレベルよりは小さい情報消去用の光量を連続的に照射する。 - 特許庁
The amount of the temperature variation measured by the temperature sensor arranged on the surface of the battery is checked on whether it is larger than the reference value or not (S2), if it is smaller than the reference value, the weighted synthetic remaining capacity is calculated from the remaining capacities determined from the current integration and from the opened voltage using the weight (S6-S12).例文帳に追加
バッテリの表面に設置した温度センサによる温度の変化量が基準値以上か否かを調べ(S2)、基準値より小さい場合、センサ温度を用い、電流積算による残存容量と開放電圧に基づく残存容量とをウェイトを用いて重み付けした合成残存容量を算出する(S6〜S12)。 - 特許庁
The motor controller includes a counter 26; an R/D converter unit 14, that receives the rotation angle signal from a resolver and increases or decreases the count value at a counter 26, in correspondence with the rotation angle signal; and a microcomputer unit 40, that reads the count value on the counter 26 and uses it as the electrical angle of a motor to control motor current.例文帳に追加
モータ制御装置は、カウンタ26と、レゾルバからの回転角信号を受け、カウンタ26のカウント値を回転角信号に対応するように増減させるR/Dコンバータ部14と、カウンタ26のカウント値を読み出してモータの電気角として用いモータ電流を制御するマイコン部40とを備える。 - 特許庁
A comparator 14 compares a detection signal Vdet' based on a coil current passed through the output inductor L1 of the switching regulator 200 with the error signal Verr from the error amplifier 10 and outputs an off signal Soff that is brought to the high level when the value of the detection signal Vdet' reaches the value of the error signal Verr.例文帳に追加
コンパレータ14は、スイッチングレギュレータ200の出力インダクタL1に流れるコイル電流に応じた検出信号Vdet’を、誤差増幅器10からの誤差信号Verrと比較し、検出信号Vdet’の値が誤差信号Verrの値に達するとハイレベルとなるオフ信号Soffを出力する。 - 特許庁
According to the deviation between the target value of the trim angle of the outboard motor and the trim angle detected by a trim angle sensor 5, the trim angle is converged to the target value by controlling with PWM the drive current provided from the DC power supply 10 to the PTT motor 4 through the H bridge circuit 11 by the control device.例文帳に追加
船外機のトリム角の目標値とトリム角センサ5により検出されるトリム角との偏差に応じて直流電源10からHブリッジ回路11を通してPTTモータ4に与えられる駆動電流をPWM制御してトリム角を目標値に収束させる制御を行わせる。 - 特許庁
To provide a single integral type analog/digital converter that uses a low frequency analog/digital conversion clock in order to monitor and measure an integral value of battery charging/discharging currents with low power consumption and extended dynamic range and measures an integral value even from a bipolar input current.例文帳に追加
バッテリーの充放電電流の積算値を監視、計測するために、低周波のA/D変換用クロックを使用しながら低消費電力化を図り且つダイナミックレンジを拡大するとともに、正負極性の入力電流に対しても一台の積分型A/Dコンバータで積算値の計測を行うこと。 - 特許庁
To converge the voltage of a current generated by a generator to the target value in its early stage, by switching the control into the feedback control by the target power when the convergency to the target value of feedback control is low, thereby operating the generator to its maximum within the range of tolerable generation capacity.例文帳に追加
フィードバック制御の目標値への収束性が低いときに目標電力によるフィードバック制御に切り替えることにより、発電機を許容され得る発電能力の範囲内において最大限に稼働させて、発電機の発電電圧又は発電電流を早期に目標値に収束させる。 - 特許庁
The method of managing an electrostatic chuck 100 including an electrode 11 and an insulating film 15 provided on the electrode 11 uses an eddy-current-type film thickness measuring device 200 to measure the film thickness of the insulating film 15, and compares the measured film thickness value of the insulating film 15 with a previously set reference value.例文帳に追加
電極11と、電極11上に設けられた絶縁膜15と、を有する静電チャック100の管理方法であって、渦電流式膜厚測定器200を用いて、絶縁膜15の膜厚を測定し、測定された絶縁膜15の膜厚値と予め設定された基準値とを比較する。 - 特許庁
A fuel cell voltage calculation result 63 obtained by dividing an effective value 51 obtained by an effective power calculation unit 45, by a direct current detection value Idc24 with a divider 60 is passed through a first order lag filter 64 to obtain a fuel cell voltage calculation result 63' after the first order lag filter.例文帳に追加
有効電力演算器45により得られた有効電力値51を直流電流検出値Idc24で割算器60により除算して燃料電池電圧演算結果63を得て、一次遅れフィルタ64を通すことにより一次遅れフィルタ後の燃料電池電圧演算結果63’を得る。 - 特許庁
This method for programming the phase change memory device comprises a process of measuring the resistance value of a phase change substance during programming of the phase change memory device and adjusting the current to be supplied to the phase change substance in the phase change memory device in response to the measured resistance value.例文帳に追加
相変化メモリ装置をプログラミングする方法において、相変化メモリ装置のプログラミング中に相変化物質の抵抗値を測定し、測定された抵抗値に応答して、相変化メモリ装置の相変化物質に供給する電流の大きさを調節する工程を含む相変化メモリ装置のプログラミング方法である。 - 特許庁
The control block 30 calculates a direction and quantity of astigmatism as difference of a value of the FE signal when amplitude of the RF signal becomes the maximum and a value of the FE signal when amplitude of the TE signal becomes the maximum, and a current is supplied only to a heater arranged at a direction of phase advance.例文帳に追加
制御ブロック30はRF信号の振幅が最大になる時のFE信号の値及びTE信号の振幅が最大になる時のFE信号の値の差として非点収差の方向及び量を算出し、位相が進んでいる方角に設置されている発熱ヒータにのみ電流を供給する。 - 特許庁
If an impediment condition is met in which the value of a current carried by the fan motor 7 is equal to or greater than a preset value which indicates that rotation of the radiator fan is impeded, a drive control circuit 1 executes control to cope with the impediment by stopping the drive of the fan motor 7 while the impediment condition stands.例文帳に追加
駆動制御回路1は、ファンモータ7に通電される電流値が、ラジエータファンの回転が阻害されていることを示す予め設定された設定値以上となる阻害条件が成立したときには、この阻害条件が成立している間、ファンモータ7の駆動を停止させる阻害対応制御を実行する構成とした。 - 特許庁
A voltage is applied to a resistance wire 7 arranged in a processing chamber 3, the resistance of the resistance wire is calculated from the value of a current flowing through the resistance wire, and then the timing of cleaning is determined in accordance with the correlation of the resistance value of the resistance wire with the thickness of a film attached to the inner wall of the processing chamber.例文帳に追加
プロセスチャンバ3内に配置された抵抗線7に電圧を印加し、抵抗線に流れる電流値から抵抗線の抵抗値を算出した後に、抵抗線の抵抗値とプロセスチャンバ内部に付着した膜の膜厚との相関関係に従ってクリーニング処理のタイミングを決定する。 - 特許庁
The air-fuel ratio learning value is set for each region of air-fuel ratio learning divided according to the engine load, and when the feedback correction factor converges into the specified range within the air-fuel ratio learning region corresponding to the current engine load, learning of the air-fuel ratio learning value in the applicable air-fuel ratio learning region is completed.例文帳に追加
この空燃比学習値は、機関負荷に応じて区分される空燃比学習領域毎にそれぞれ設定され、現在の機関負荷に対応した空燃比学習領域にてフィードバック補正係数が上記所定範囲内に収束したとき、同空燃比学習領域での空燃比学習値の学習が完了する。 - 特許庁
Large delay phase compensation (small advance phase compensation) is applied to steering torque VT3 that is output from a steering torque sensor 30 as a divided value (assist current/operation torque=Ia/VT3) obtained by dividing a value of an assist current Ia which makes an electric motor generate assist torque by the value of the steering torque VT3 detected by the steering torque sensor 30 becomes large.例文帳に追加
電動モータにアシストトルクを発生させるアシスト電流Iaの値を、操舵トルクセンサ30により検出された操舵トルクVT3の値で割った除算値(アシスト電流/操舵トルク=Ia/VT3)が大きい程、操舵トルクセンサ30から出力される操舵トルクVT3に対して大きな遅れ位相補償(小さな進み位相補償)を施すようにしたので、制御安定性が確保されるとともに、操舵フィーリングが低下する除算値の小さい領域では、大きな進み位相補償を施すようにしたので、良好な操舵フィーリングが得られる。 - 特許庁
The power supply circuit includes: a voltage source circuit; a feedback circuit which feedbacks so as to maintain the output of the voltage source circuit constant and includes a first variable resistor for trimming the output to a desired value; and a current source circuit which is used for supplying a drive current to the voltage source circuit and includes a second variable register for trimming the current quantity of the drive current when trimming is performed by the first variable register.例文帳に追加
電源回路は、電圧源回路と、該電圧源回路の出力を一定に維持するようフィードバックを行うフィードバック回路であって、前記出力を所望の値にトリミングするための第1の可変抵抗器を含む前記フィードバック回路と、前記電圧源回路に駆動電流を供給するための電流源回路であって、前記第1の可変抵抗器によりトリミングが行われたときに、前記駆動電流の電流量をもトリミングするための第2の可変抵抗器を含む前記電流源回路と、を備える。 - 特許庁
The battery status administration system turns on a load 17 and forcedly discharge when practically full charge of the battery 11 is detected, detects the terminal voltage lowering and discharge current value at the moment are detected by way of a voltage sensor 3 and a current sensor 1, and judges a degradation of the battery 11 based on the internal resistance value of the battery 11 derived from the detection values.例文帳に追加
このバッテリ状態管理装置では、バッテリ11の充電残量が実質的に満充電になったことを検出した際に、負荷17をオンしてバッテリ11に強制的に放電を行わせ、その際の端子電圧の下降量及び放電電流値を電圧センサ3及び電流センサ3を介して検出し、それらの検出値に基づいて導出したバッテリ11の内部抵抗値に基づいてバッテリ11の劣化度を判定する。 - 特許庁
Then, an output power of the fuel cell 2 is controlled by the DC-DC converter 3 so as to be not less than a preset lowest output voltage value of the fuel cell 2, and an output current detected by the ammeter 4 is controlled by the DC-DC converter 3 so as to be not more than a preset stable output current value of the fuel cell 2.例文帳に追加
そして、燃料電池2の出力電力を、電圧計測器5で検出される出力電圧があらかじめ設定された燃料電池2の出力最低電圧値以上になるように直流−直流変換器3によって制御し、電流計測器4で検出される出力電流があらかじめ設定された燃料電池2の安定出力電流値以下になるように直流−直流変換器3によって制御する。 - 特許庁
This invention relates to the semiconductor laser drive circuit which processes an irradiated body by irradiating a laser beam, while causing a laser output to be a predetermined set value by carrying out a feedback control, wherein the set value is a laser drive current value corresponding to the laser output of the semiconductor laser, characterized by a function of a laser irradiation time duration.例文帳に追加
本発明になる半導体レーザ駆動回路は、フィードバック制御することでレーザ出力を予め定められた設定値になるようにしながらレーザ光を照射することで被照射物を加工する半導体レーザの駆動回路であって、前記設定値は、前記半導体レーザのレーザ出力に対応したレーザ駆動電流値であって、レーザ照射時間の関数であること、を特徴とするものである。 - 特許庁
A controller for a synchronous machine calculates an armature interlinkage magnetic flux according to a permanent magnet of the machine based on a basic wave current or its command value and a harmonic voltage command value, estimates a temperature of the magnet to the armature interlinkage magnetic flux calculated value by referring to a table of a permanent magnet temperature to the armature interlinkage magnetic flux, and regulates an output of the machine in response to the estimated temperature of the magnet.例文帳に追加
同期機の回転速度、基本波電流またはその指令値、および高調波電圧指令値に基づいて同期機の永久磁石による電機子鎖交磁束を演算し、電機子鎖交磁束に対する永久磁石温度のテーブルを参照して電機子鎖交磁束演算値に対する永久磁石の温度を推定し、永久磁石の推定温度に応じて同期機の出力を調節する。 - 特許庁
The paper feeding device is provided with a power supply means for supplying driving power to the drive means in response to a driving signal for the drive means, a current/voltage detecting means for detecting current or voltage value which is supplied to the drive means by the power supply means and a signal outputting means for outputting a prescribed warning display signal according to the detected result from the current/voltage detecting means.例文帳に追加
また,上記駆動手段に対する駆動信号に応じて上記駆動手段に駆動電力を供給する電力供給手段と,上記電力供給手段により上記駆動手段に供給される電流値及び/又は電圧値を検出する電流/電圧検出手段と,上記電流/電圧検出手段による検出結果に応じて所定の警告表示信号を出力する信号出力手段を設ける。 - 特許庁
By collating the authentication image in the current collation failure with the authentication image in the collation failure registered in association with the registration image, similarity is determined, and if a higher collation value is determined in both current and previous determination and high similarity is determined between the authentication image in the previous collation failure and that of current one, an operation warning is displayed.例文帳に追加
今回の認証時の照合失敗時の認証用画像を登録画像に関連づけて登録しておいた照合失敗時の認証用画像と照合して類似性を判定し、前回および今回の照合値の大小判定によりいずれも照合値大で、かつ類似性判定により前回の認証失敗時の認証用画像と今回の認証失敗時の認証用画像が類似性大と判定されたときに、操作警告表示する。 - 特許庁
An optical receiver includes: an optical amplifier amplifying input light, that is a wavelength-multiplexed optical signal, according to an operating current supplied thereinto; a demultiplexer demultiplexing output light of the optical amplifier; and an operating-current control circuit selecting a monitoring target from a plurality of wavelength signals output from the demultiplexer and controlling the operating current of the optical amplifier so that optical power of the monitoring target is controlled to be a predetermined control value.例文帳に追加
光受信器は、供給される動作電流に応じて波長多重光信号である入力光を増幅する光増幅器と、光増幅器の出力光を分波する分波器と、分波器から出力される複数の波長信号からモニタ対象を選定しモニタ対象の光パワーが所定の制御値に制御されるように光増幅器の動作電流を制御する動作電流制御回路と、を備える。 - 特許庁
In a starting period (high-frequency operation period), the step-down chopper circuit is so controlled as to allow the dielectric breakdown of the discharge lamp La and thereafter set the voltage of the capacitor C1 at a value allowing a predetermined high-frequency current to flow.例文帳に追加
また、始動時(高周波動作期間)においては、放電ランプLaの絶縁破壊が可能となり、その後、所定の高周波電流が流れるようなコンデンサC1の電圧となるように、降圧チョッパ回路を制御する。 - 特許庁
To provide a liquid crystal composition which has an electric current value controlled without deteriorating various liquid crystal characteristics such as response and has high reliability, and to provide a liquid crystal element which uses the liquid crystal composition and has a high contrast.例文帳に追加
レスポンス等の液晶諸特性を低下させることなく、電流値を抑制した信頼性の高い液晶組成物を提供すること、また、この液晶組成物を使用したコントラストの高い液晶表示素子を提供する。 - 特許庁
In the input buffer circuit 21, the threshold value changing circuit is activated at the time of a test mode, current quantity of the N channel MOS transistor 215 is increased, voltage of a node N1 is increased, and the reference voltage VREF is changed equivalently.例文帳に追加
入力バッファ回路21は、テストモード時閾値変更回路が活性化され、NチャネルMOSトランジスタ215の電流量を増加させてノードN1の電圧を増加させ、基準電圧VREFを等価的に変化させる。 - 特許庁
The temperature characteristic of a physical quantity conversion factor G is memorized in the memory device 3 as detection value correction information, and thus, temperature correction including individual differences of the physical quantity conversion factor G of each current sensor circuit 2 is performed.例文帳に追加
記憶装置3には検出値補正情報として物理量変換係数Gの温度特性が記憶され、これにより各電流センサ回路2の物理量変換係数Gの個体差を含めた温度補正が行われる。 - 特許庁
Each light-emitting element is driven at constant current and a monitor light-emitting element is utilized, so that a high efficiency output voltage corrected to an optimum value is supplied to the light-emitting element and stable driving over a long period of time is achieved.例文帳に追加
各発光素子を定電流駆動させ、モニタ用発光素子を利用することで、最適な値に補正された高効率の出力電圧を発光素子に供給し、長時間に渡って安定した駆動を実現させる。 - 特許庁
The measurement probe is provided with first and second probe parts each having a contact part brought into contact with the measurement object for measuring the resistance value of the measurement object, wherein one probe is used for voltage measurement and the other is used for application of a current.例文帳に追加
測定用プローブは、測定対象の抵抗値を測定するために測定対象と接触する接触部をそれぞれ有し、一方が電圧測定に他方が電流印加に用いられる第1及び第2のプローブ部を備える。 - 特許庁
Since the converter outputs Vi1, Vi2 do not depend on a DC voltage Ed, when Ed is lower than the rated value at the time of recover from an accident, there is no voltage difference from the system 1 and therefore generation of eddy current can be avoided.例文帳に追加
変換器出力Vi1、Vi2が直流電圧Edに依存しなくなるので、事故からの復帰時などでEdが定格より低い場合に、系統1との電位差が生じないので、過電流の発生が回避できる。 - 特許庁
To provide a laser light output control circuit for preventing a control signal of an excessive current value from being applied to a semiconductor laser even when a power voltage temporarily drops, and to provide a laser driving method.例文帳に追加
電源電圧が一次的に降下したときにでも、過大な電流値の制御信号が半導体レーザへ印加されてしまうことを防止することができるレーザ光出力制御回路及びレーザ駆動方法を提供する。 - 特許庁
A limiting circuit 12 for secondary duty delivers a clock signal set_2 with a timing, when making on-duty of secondary current that begins to flow to a secondary winding 110B of a transformer 110 from turn-off timing of a switching device 1 constant at a predetermined value.例文帳に追加
2次デューティ制限回路12は、スイッチング素子1のターンオフのタイミングからトランス110の2次巻線110Bに流れ始める2次電流のオンデューティを所定値で一定にするタイミングでクロック信号set_2を出力する。 - 特許庁
To provide an image decoder that can be downsized and can reduce the maximum value of a consumed current in the case of simultaneously outputting digital image data of a plurality of channels and to provide a semiconductor device and an image decoding method.例文帳に追加
複数チャネルのデジタル画像データを同時に出力する場合に、装置の小型化が可能であり、また消費電流の最大値を削減することができる画像復号装置、半導体装置、及び画像復号方法を提供する。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|