例文 (642件) |
正準形の部分一致の例文一覧と使い方
該当件数 : 642件
キャリアフィルム41に、予め形成されていた基準孔41tに基づいて、正極予備体27を切断して正極7を得る工程と、正極7、負極10およびセパレータ3でセル20を組立てる工程とを行なう。例文帳に追加
Based on a reference hole 41t formed in advance in the carrier film 41, a process for obtaining a positive electrode 7 by cutting the positive electrode preliminary body 27, and a process for assembling a cell 20 by the positive electrode 7, a negative electrode 10, and a separator 3 are carried out. - 特許庁
発振した基準電流信号周波数および基準電流波形と、ELディスプレイに印加される電流周波数および電流波形とが、前記基準と同一になるように閉ループ制御し、前記ELディスプレイ印加電流を制御することによって、結果として90度位相遅れの適正な交流電圧がELディスプレイにかかる方式を提供した。例文帳に追加
By controlling the current applied to the EL display, proper alternating voltage with a right angle phase delay is applied to the EL display. - 特許庁
マイクロレンズアレイと隣り合う透明媒体の上に形成された付加的な光学形状は、反対側の表面がコリメートされた光ビームに露光されるときに、該表面に基準マークを正確に位置決めすることを可能にする。例文帳に追加
The additional optical shape formed on the transparent medium adjacent to the microlens array enables the accurate positioning of the fiducial mark on the surface when the surface on the opposite side is exposed with collimated light beams. - 特許庁
IF信号周波数特性補償部7は、高域減衰波形である入力IF信号に対し、特別な基準信号などを利用せず、ディジタル変調波そのものを利用して自動的に平坦な波形に補正する。例文帳に追加
An IF signal frequency characteristic compensation part 7 automatically corrects an input IF signal to be a high frequency decay waveform to a flat waveform by using the digital modulated wave itself without using a special reference signal. - 特許庁
対例外的基準波形評価値が第2許容値範囲内にある場合には、異常な検出信号波形が検出される場合であってもエンジン1を正常と判定する(S5)。例文帳に追加
The engine 1 is determined to be normal (S5), even when an abnormal detection signal waveform is detected, in the case where the evaluation value-to-exceptional-reference-waveform is within the second allowance range. - 特許庁
階段状となる回折パターンの形状評価を正確に行うことができる測定基準としてのマークを有する光学素子の成形金型を提供する。例文帳に追加
To provide a molding die of an optical element having a mark serving as measurement reference capable of correct shape evaluation of a stepped diffraction pattern. - 特許庁
自動車の外観を形成する外観部材を設計する際に外観形状が衝突時の安全基準に適合しているか否か等を容易かつ正確に判別できるようにする。例文帳に追加
To easily and accurately discriminate whether or not an exterior shape meets safety standards for collision in designing an exterior member that forms the exterior of an automobile. - 特許庁
インサート成形工程の準備段階で、成形主体の型内に配置されるファスナー保持用のガイドに対して、ファスナーを適正位置に迅速に位置決めする。例文帳に追加
To speedily position a fastener correctly to a guide for holding a fastener inside the mold of a molding subject in the preparation step in the insert-molding process. - 特許庁
エッジ画像における基準点の対応付けを簡単な処理で正確に行なうことでリアルタイム処理も可能な立体形状検出装置及び立体形状検出方法を提供する。例文帳に追加
To provide a three-dimensional shape detector and a three-dimensional shape detection method for achieving even real-time processing by accurately correlating reference points in edge images by simple processing. - 特許庁
合わせマーク2は、上側基準層33の上に薄膜34を介して形成されたレジストパターン35の一部であり、正方形の4辺に配置された穴21の集合体である。例文帳に追加
A registration mark 2 is a part of a resist pattern 35 formed on the upper reference layer 33 through a thin film 34 and is an aggregate of holes 21 arranged on four sides of a square. - 特許庁
第一端子アレー5は、基板コア100の板面と平行な基準面への正射投影において、セラミック副コア部1の投影領域内に全体が包含される位置関係にて形成されて形成されている。例文帳に追加
The first terminal array 5 is formed in such a positional relation as the entirety is included in the projection area of the ceramic sub-core section 1 in the orthogonal projection to a reference plane parallel with the plane surface of the substrate core 100. - 特許庁
前記補正量は、目標パターンサイズと基準露光量を指定して形成したレジストパターンサイズと目標パターンサイズとの差分に対応する可変矩形ビームサイズデータである。例文帳に追加
The above amount of corrections is variable rectangular beam size data corresponding to the difference of a target pattern size, a resist pattern size formed by specifying the amount of the reference light exposure, and the target pattern size. - 特許庁
心電図アーチファクト波形の正規化標準波形を算出することなく、測定した心電図に含まれている脳波を抽出することのできる脳波測定装置および脳波測定方法を提供することを目的とする。例文帳に追加
To provide an electroencephalograph and electroencephalography which can extract brain waves included in a measured electrocardiogram without calculating a normalized standard waveform of electrocardiogram artifact waveform. - 特許庁
一方、該補償トルクダウン量Req_Tが所定の基準トルクT0を下回る場合には、正弦波による駆動を継続し、又は、矩形波駆動を行っている場合は、矩形波駆動を終了する(ステップS6)。例文帳に追加
On the other hand, in a case when the compensating torque down quantity Req_T is lower than the predetermined standard torque T0, the driving by sine-wave is continued, or the driving by rectangular wave is terminated, when the driving by rectangular wave is executed (Step S6). - 特許庁
変形面18上に形成された歪検出用静電容量変化式歪センサ部16を備える歪センサと基準歪センサとの出力差に基づいて歪センサの出力を温度補正する。例文帳に追加
On the basis of the output difference between a distortion sensor provided with a variable capacitance-distortion sensor 16 for detecting the distortion formed on a deformation surface 18 and the reference distortion sensor, temperature correction is performed on the output of the distortion sensor. - 特許庁
導線及び被観察部をめっきで形成することにより、導線の接触部の位置を基準に、基板上の特定位置に正確に被観察部を形成することができる。例文帳に追加
The lead wire and the part to be observed are formed by plating, and thereby the part to be observed can be formed accurately on a specific position on the substrate based on the positions of the contact parts of the lead wire. - 特許庁
この場合、変形量および補正量は、それぞれ、所望の形状の歯14における歯面の中心Oを基準点として数値化された歯厚、ねじれ角、圧力角等の各要素の値によって表される。例文帳に追加
In such a case, the deformed amount and the correcting amount are shown with value of each element in digitized gear thickness, twist angle, pressure angle, etc., with the center of a gear surface in a desired shape of the gear as the reference point, respectively. - 特許庁
そして、この接地位置を基準点として、溝掘り作業機を下降させることによって、溝の始端部において、設定された初期深さまで正確に溝を形成し、この始端部から所定の勾配で圃場に溝を形成する(S4)。例文帳に追加
With the grounding position being the reference point, the ditch is accurately formed up to the set initial depth at the starting end part of the ditch by lowering the ditch digging machines, and the ditch is formed in the agricultural field with the predetermined inclination from the starting end part (S4). - 特許庁
テスト画像について、基準の画像と実際に形成された画像の比較を同様に行い、異常がなければ、前記した中間範囲と判定された画像を正常なものとみなし、中断した画像形成を再開する。例文帳に追加
When there is no abnormality, the image forming apparatus judges that the image judged as in the intermediate range is a normal image, and then the forming of the interrupted image is restarted. - 特許庁
第一端子アレー5は、基板コア100の板面と平行な基準面への正射投影において、セラミック副コア部1の投影領域内に全体が包含される位置関係にて形成されて形成されている。例文帳に追加
A first terminal array 5 is formed in a positional relationship such that, as viewed in the orthogonal projection to the reference plane parallel to the plate surface of the board core 100, the entire first terminal array 5 is included in the projection area of the ceramic sub-core 1. - 特許庁
電池缶1の正極缶5の底面壁11の外面に形成した平面領域には、中心線平均粗さRa(JIS B 0601に準拠)を100μmに設定した粗面領域29が形成される。例文帳に追加
In the plane region formed on the external face of the bottom wall 11 of the positive electrode can 5 of the cell can 1, a rough surface region 29 of which the center line average roughness Ra (based on JIS B 0601) is established at 100 μm is formed. - 特許庁
基準表面の形状と傾斜を判定及び除去する為、及び、厚さ変化と形状の計算の為の二つの単一側面計測の正しい重ね合わせを容易にする為に、諸対策を講じる。例文帳に追加
various countermeasures are worked out to determine and remove a shape and a slope of each reference surface, and to correctly overlap easily for two single side face measurements for calculating the thickness variation and the shape. - 特許庁
監視装置は、ユーザインタフェースの設定情報が画像形成装置のユーザインタフェースの設定情報の正当性を示す判断基準に合致するか否か判断し、判断結果を画像形成装置に送信する。例文帳に追加
The monitoring device determines whether or not the setting information of the user interface matches with a determination standard indicating the validity of the setting information of the user interface of the image forming device and transmits the determination result to the image forming device. - 特許庁
従って、円柱形体の端にある成形基準面によって、以降の仕上げ作業のために正確で安全な保持、位置決め、ハンドリング、配置を行うことができる。例文帳に追加
Thus, accurate and safe capture, positioning, handling and placement for a subsequent finishing operation are performed with the molded reference surface located at the end of a cylindrical body. - 特許庁
正極端子2、負極端子3には、基準穴5に対して導出幅方向の両側が非対称となるように一側にそれぞれ矩形状の切り欠き部2’、切り欠き部3’が形成されている。例文帳に追加
On each positive electrode terminal 2 and each negative electrode terminal 3, an oblong cutout part 2' and an oblong cutout part 3' are formed on one side to set both its sides in the leading-out width direction asymmetrical with respect to the reference hole 5, respectively. - 特許庁
被写体画像からその被写体の形状を抽出する被写体形状抽出装置において、任意の背景を含む被写体画像を入力する画像入力手段1と、被写体画像から被写体形状を切り出す画像切り出し手段7と、切り出された被写体形状に基づき、被写体に類似する標準3次元形状モデルの形状を修正する形状修正手段8とを設ける。例文帳に追加
This object shape extraction device for extracting the shape of the object from the object image is provided with an image input means 1 for inputting the object image including an optional background, an image segmentation means 7 for segmenting the object shape from the object image and a shape correction means 8 for correcting the shape of a standard three- dimensional shape model similar to the object based on the segmented object shape. - 特許庁
波形記憶部35には、フラッシュランプから正常な光照射が行われたときの光強度の時間波形である基準波形、および、処理対象となる基板に光照射が行われたときの光強度の時間波形である処理波形が記憶される。例文帳に追加
The waveform storage section 35 stores a reference waveform as a time waveform of the light strength in executing normal light irradiation by the flash lamp, and a processing waveform as a time waveform of the light strength when a substrate to be treated is irradiated with light. - 特許庁
波形記憶部35には、正常な光照射が行われたときの放射光強度の時間波形である基準波形、および、処理対象となる基板に光照射が行われたときの放射光強度の時間波形である処理波形が記憶される。例文帳に追加
The waveform storage section 35 stores a reference waveform as a time waveform of the intensity of radiated light when light irradiation is normally executed and a treatment waveform as a time waveform as the intensity of radiated light when the substrate to be treated is radiated with light. - 特許庁
識別回路D1において、波形整形回路3は、2分岐された一方の多値信号MSの波形を、制御信号生成回路10からの制御信号CSに基づいて、後段の検出回路4が第1の基準レベルRL_1 を正しく検出可能な波形に整形する。例文帳に追加
A waveform shaping circuit 3 of the identification circuit D1 shapes a waveform of one multi-value signal Ms of two-branched signals on the basis of a control signal CS from a control signal generating circuit 10 into a waveform from which a post-stage detection circuit 4 can correctly detect a 1st reference level RL1. - 特許庁
搬送ベルト上に位置合わせ用パターンを形成して位置ずれを補正した際に基準経過時間を算出し、基本色の位置合わせ用パターンを複数の感光体ドラムの夫々に形成し、その感光体ドラム上の位置合わせ用パターンを検出し、その検出結果と基準経過時間とに基づいて、位置ずれを補正する。例文帳に追加
A reference elapsed time is calculated when the pattern for alignment is formed on a conveying belt so as to correct positional deviation, the pattern for alignment of basic color is formed on each of a plurality of photoreceptor drums, and the pattern for alignment on the photoreceptor drum is detected, then the positional deviation is corrected based on a result of the detection and the reference elapsed time. - 特許庁
そして、前記第1補正値算出ステップ及び前記第2補正値算出ステップは、基準パターンの読み取り結果を用いるものであり、前記第1補正値算出ステップ及び前記第2補正値算出ステップの前に、前記基準パターンの形成された基準シートが、前記第1読み取りステップの読み取り範囲及び前記第2読み取りステップの読み取り範囲をカバーするように前記スキャナに予め設けられる。例文帳に追加
The first correction value calculation step and the second correction value calculation step use results of reading reference patterns, and the reference sheet having the reference patterns formed thereon is preliminarily provided on the scanner so as to cover a read range of the first read step and that of the second read step, before the first correction value calculation step and the second correction value calculation step. - 特許庁
クロスト−クにより基準ランプ電圧が変動して、正極性映像信号及び負極性映像信号が変動したとしても、H.BLK期間内で(K)のランプ波形が本来の波形に戻っていれば、正しい映像信号を書き込むことができる。例文帳に追加
Even when a positive video signal and a negative video signal are changed by the change of a reference ramp voltage due to cross-talk, a correct video signal is written, when the ramp waveform of (K) is returned to an original waveform within the H.BLK period. - 特許庁
飛行条件に依存した観測対象のプルーム形状をデータベース4で推定演算し、観測方向補正装置3により、プルーム形状に起因した赤外線センサ1の観測方向と機体基準点とのずれを軽減した補正観測方向を取得する。例文帳に追加
The plume shape of the observation target depending on a flight condition is estimated and computed by the database 4, and by the observation direction correction device 3, the corrected observation direction in which a deviation between the observation direction of the infrared ray sensor 1 and an airframe reference point caused by the plume shape is reduced is acquired. - 特許庁
本発明に係る医用画像読取装置3によれば、CPU41は、一様露光画像データから基準補正データを算出し、大きさとX線吸収率の異なる被写体を配置して撮影して得られたN個の矩形被写体画像データからN個の矩形被写体補正データを作成する。例文帳に追加
The medical image reader 3 allows a CPU41 to calculate standard correction data from uniform light exposure image data and form correction data on N rectangular objects from the image data on those obtained by locating objects whose sizes and X-ray absorptances are different and taking pictures of them. - 特許庁
コンピュータ等の出力機器として使用される画像形成装置において、色ずれ量を検出するためのレジストレーションパターンを読み取る際に、基準色の画像形成むらが大きい場合、その影響によって正しく色ずれ量を換算できず色ずれ量演算が正確に行えない。例文帳に追加
To solve a problem that the color blur can not be calculated correctly because of the influence of the remarkable image formation unevenness due to the reference color derivation when a registration pattern is read for measurement of the color deviation in an image forming device which is used as an output device of computer, etc. - 特許庁
予め可塑化した樹脂をプランジャで金型内に注入する射出成形機の制御方法であって、圧力損失の変化に対応させて、樹脂の射出圧力が、基準圧力値Pに圧力補正値ΔPを加算した値となるように補正制御しながら成形する。例文帳に追加
The method for controlling the injection molding machine is the one for injecting a previously plasticized resin in a mold by using a plunger, molding is carried out by controlling the injection pressure making under corresponding a change of a pressure loss and under calibulating an injection pressure of the reesin to be a value that a pressure correction value ΔP is added to a standard pressure value P. - 特許庁
正規リムにリム組みしかつ正規内圧を充填した無負荷である基準状態においてビード部4がリムと接触するリム接触域に、タイヤ加硫金型によって成形されかつビードコア5に向かって凹む凹み部9を形成したことを特徴としている。例文帳に追加
In a no-load standard condition where rimmed in a regular rim and filled up with regular internal pressure, a recessed part 9 molded by the tire vulcanizing mold and dented toward a bead core 5 is formed in a rim contact area where a bead part 4 contacts with the rim. - 特許庁
予め、プリンタで形成した複数階調のパターン濃度をスキャナで測定して該濃度値を所定特性に補正する濃度補正テーブルを作成し、また、プリンタ内部に形成したパターンの濃度をセンサで測定し、その基準値を設定しておく。例文帳に追加
The pattern densities of plural gradations formed by a printer is measured previously by a scanner to prepare a density correction table for correcting the density to have prescribed characteristic, and the density of a pattern formed inside the printer is measured with a sensor to set its reference. - 特許庁
オプティカルブラック部は、フォトダイオードに相当する正孔蓄積層とN+型半導体層が形成された不問オプティカルブラック部と、正孔蓄積層が形成され、黒レベルの基準信号を出力するクランプオプティカルブラック部と、を有する。例文帳に追加
The optical black part has a non-optical black part, on which a hole accumulation layer and an N+-type semiconductor layer corresponding to the photo diode are formed; and a clamp optical black part, on which the hole accumulation layer is formed and which outputs reference signals of a black level. - 特許庁
酸化反応における標準電極電位が負である表面を持つ基板と、前記基板の上に設けられた前記標準電極電位が正となる保護層と、前記保護層の上に設けられたアルミニウム陽極酸化層と、を有することを特徴とする光学素子成形用金型。例文帳に追加
This optical element molding die includes the substrate having a surface with a standard electrode potential getting negative in an oxidation reaction, a protection layer with the standard electrode potential getting positive, provided on the substrate, and an aluminum anodic oxidation layer provided on the protection layer. - 特許庁
すなわち、シミュレーションの結果が塗装実験の結果に線形比例するものと考え、初期基準塗装パターンに影響を与える塗料吐出の過渡過程を、塗装実験の結果を用いて初期基準塗装パターンを修正することにより補償する。例文帳に追加
Compensation is provided by correcting the initial basic coating pattern using the result of the coating experiment in a transient process of discharging the coating material which influences the initial basic coating pattern under the assumption that the simulation result is linearly proportional to the result of the coating experiment. - 特許庁
画像形成装置は、シートの先端辺及び側端辺のうちの一方を斜行補正の基準辺として選択する選択部34と、選択部34により選択された基準辺の傾きを検知するエリアセンサ24と、を備えている。例文帳に追加
The image forming device has a selecting part 34 for selecting one of the front edge and the side edge of a sheet as the reference edge of skew correction, and an area sensor 24 which detects the inclination of a reference side selected by the selecting part 34. - 特許庁
根管治療前に根管の形状等の確認、基準位置から根尖部までの距離を正確に測定ができ、さらに、根管治療時において根管治療器具の先端が基準位置から移動した距離をリアルタイムに表示する。例文帳に追加
To perform the confirmation of the shape or the like of a root canal and the accurate measurement of a distance from a reference position to an apical part before root canal treatment, and to display the distance that the front end of a root canal treating implement has moved from the reference position in real time during root canal treatment. - 特許庁
使用者が、標準規格紙や標準規格紙と同寸法の粘着シールを用いて自由に背見出し用紙をカスタマイズして作成し使用しても外観の悪化を招かず、また、背ポケット部を形成するための樹脂フィルムの溶着状態を適正なものとすることができるファイルを提供する。例文帳に追加
To provide a file in which a back heading sheet can be freely customized and used, with a standard specification sheet or an adhesive seal having the size same as the standard specification sheet, without deteriorating its outer appearance, and the welding state of a resin film to form a back pocket section can be made appropriate. - 特許庁
レーザー光線の照射位置に基準線を合わせて目盛を読み取る寸法測定具を、軽量で、取り扱いが簡単で、かつ、部屋の寸法を畳の標準寸法に対する正負の偏差の形で少なくとも「厘」以下の単位まで測定可能なものとする。例文帳に追加
To make a size measuring tool adjusting a reference line at the irradiation position of a laser beam and reading the gradation light, easy to treat and capable of measuring the size of a room at least with the unit of 'rin' (ca. 3 mm) or less in the form of positive or negative deviation for the standard scale of 'tatami' (straw mat). - 特許庁
つぎに、記憶テーブル36に記憶された最大ピーク基準値VAM′、最小ピーク基準値VAN′それぞれに対して、求められた入力最大ピーク値VAM、入力最小ピーク値VANが一致するように、第1の検出信号400Aの波形が、400A′に補正される。例文帳に追加
Then, waveform of the first detection signal 400A is corrected to be 400A' so that the obtained input maximum peak value VAM and the input minimum peak value VAN coincide with the maximum peak reference value VAM' and the minimum peak reference value VAN' stored in a storage table 36, respectively. - 特許庁
それぞれの測定対象箇所の距離が求められたら、その距離と基準値を比較し、その結果から、基準値からのずれが許容範囲を超えていれば、設定値算出部5において補正量を算出し、画像形成部1の各部を調整するための設定値を求めて記憶部3に記憶させる。例文帳に追加
After finding out a distance of each position to be measured, the distance is compared with a reference value, and when a deviation from the reference value exceeds an allowable range as the compared result, a set value calculation part 5 calculates a correction amount, finds out set values for adjusting respective parts of an image forming part 1 and stores the set values in a storage part 3. - 特許庁
読取画像データと基準画像データとについてそれぞれの対応する基準図形同士を比較することで画像領域毎の傾き量を検出し、通常の原稿Xから読み取られた画像データの傾きを傾き量に基づいて画像領域毎に補正する。例文帳に追加
The quantities of the inclinations at every image region are detected by comparing corresponding mutual reference graphics of each of the read image data and the reference image data regarding the read image data and the reference image data, and the inclinations of the image data read from the normal original X are corrected at every image region on the basis of the quantities of the inclinations. - 特許庁
複雑な形状を有する物体であっても、複数のエッジ点に対して適切な基準線を設定し、該基準線からの各エッジ点の差異に基づいてバリ、欠け等の欠陥を正確に検出することができる欠陥検出装置、欠陥検出方法及びコンピュータプログラムを提供する。例文帳に追加
To provide a flaw detector which sets a proper reference line even to matter having a complicated shape with respect to a plurality of edge points and accurately detects a flaw such as burr, chipping or the like on the basis of the difference of each of the edge points from the reference line, a flaw detection method and a computer program. - 特許庁
例文 (642件) |
Copyright © Japan Patent office. All Rights Reserved. |
![]() ログイン |
Weblio会員(無料)になると
![]() |
![]() ログイン |
Weblio会員(無料)になると
![]() |