Synchronous Motorの部分一致の例文一覧と使い方
該当件数 : 1525件
A signal A acquired by synchronizing a pulse signal generated corresponding to rotor displacement of a motor 2 by an encoder 1 with a clock signal CLK by a flip-flop 7 is outputted, and the edge of the synchronous signal A is detected by an EXOR gate 11, and each level of the synchronous signal A and the pulse signal is compared by a comparator circuit 18 during a rising edge of the clock signal CLK.例文帳に追加
エンコーダ1がモータ2のロータ変位量に応じて発生させるパルス信号を、フリップフロップ7によりクロック信号CLKに同期させた信号Aを出力し、EXORゲート11により同期信号Aのエッジを検出し、比較回路18により同期信号Aと前記パルス信号とのレベルを、クロック信号CLKの立上りエッジ間に比較する。 - 特許庁
The controller 5 calculates a rotor position of the rotor based on the induced armature voltages VU, VV, and VW while the gas turbine shaft and the rotor rotate by inertia after the supply of power to the synchronous machine 2 from the gas turbine 1 is stopped and controls the power supply device 3 based on the rotor position to start the synchronous machine 2 as the electric motor.例文帳に追加
制御装置(5)は、ガスタービン(1)から同期機(2)への動力の供給の停止後、前記ガスタービン軸と前記回転子とが慣性により回転している状態にある間に、誘起電機子電圧(v_u、v_v、v_w)に基づいて、前記回転子の回転子位置を算出し、前記回転子位置に基づいて電源装置(3)を制御することによって同期機(2)を電動機として始動する。 - 特許庁
To facilitate its control by reducing the drive frequency of a necessary inverter and to improve durability to the high-speed revolution of a shaft by thinning a rotor core in its radial direction, in a permanent magnet synchronous motor.例文帳に追加
永久磁石同期モータにおいて、必要とされるインバータの駆動周波数を低減させることによって制御を容易とすると共に、ロータコアを径方向に薄肉化させることによってシャフトの高速回転に対する耐久性を向上させる。 - 特許庁
To provide a controller of an embedded-magnet synchronous motor and a controller for an elevator, capable of obtaining good output by determining a d-axis current command i_d* and a q-axis current command i_q* under the maximum torque control using a simple method.例文帳に追加
最大トルク制御のd軸電流指令i_d*とq軸電流指令i_q*とを、簡単な方法で求めることによって、良好な出力を得ることができる埋込磁石式の同期電動機およびエレベータの制御装置を提供する。 - 特許庁
A plurality of detecting voltage vectors Vab and Vcd are applied synchronously with a PWM signal generating a carrier wave of a control device 4, and motor currents iu and iv are detected by a current detection pulse Pd which is synchronous with the carrier wave.例文帳に追加
制御装置4のPWM信号発生用搬送波に同期して複数の検出用電圧ベクトルVab,Vcdを印加するとともに、搬送波に同期した電流検出パルスPdによりモータ電流iu,ivを検出する。 - 特許庁
In this stage, a snubber control circuit 160 estimates that a regenerative current of the synchronous motor M is increased according to information of an operation mode Md, and selects a map for setting a large duty ratio of a drive signal Snb in a snubber transistor 131.例文帳に追加
この段階では、スナバ制御回路160は、運転モードMdの情報から同期モータMの回生電流が増えることを予測し、スナバトランジスタ131における駆動信号Snbのデューティ比を大きく設定できるマップを選定する。 - 特許庁
To provide a high-output, high-efficient, and low-cost rotor of synchronous motor, wherein the dimensions of a permanent magnet high in magnetic characteristics on the outer circumferential portion of the rotor and a permanent magnet low in magnetic characteristics inside thereof are optimized.例文帳に追加
回転子外周部に配置される磁気特性の高い永久磁石と、その内側に配置される磁気特性の低い永久磁石との寸法が最適化された、高出力、高効率、低コストの同期電動機の回転子を提供する。 - 特許庁
Every time a rotary shaft of a synchronous motor 13 makes a single rotation, a converter 14 generates a number of sawtooth waves corresponding to the number of pole pairs as an initial electrical angle according to an ECU pulse output from an ECU 19 disposed on an engine 11.例文帳に追加
コンバータ14は、エンジン11に設けられたECU19より出力されるECUパルスに基づき、同期モータ13の回転軸が1回転する毎に、極対数に対応する個数の鋸歯状波を生成しこれを初期電気角とする。 - 特許庁
When starting an elevator, the torque of a permanent magnetic synchronous motor 4 is held in a magnetic pole position in stop so as to compensate reduction of the holding torque of a brake device when releasing the brake device holding a car 1 in a stop position.例文帳に追加
エレベータの起動時に、乗りかご1を停止位置に保持しているブレーキ装置を開放するときに、ブレーキ装置の保持トルクの減少を補償するように、永久磁石式同期モータ4のトルクを停止時の磁極位置に保持するよう制御する。 - 特許庁
When a winding speed of the yarn is accelerated or decelerated, synchronous control is performed so as to accelerate or decelerate a traverse guide drive motor for driving a traverse guide such that traverse of the yarn by the traverse guide is synchronized to acceleration or deceleration of the winding speed.例文帳に追加
糸の巻取速度が加速又は減速しているときに、前記トラバースガイドによる糸の綾振りが前記巻取速度の加速又は減速に同期するように、トラバースガイドを駆動するトラバースガイド駆動モータを加速又は減速するように同期制御する。 - 特許庁
By doing so, since a magnetic path can be formed substantially in a shape of a saddle, the necessary length of the saddle can be reduced, the rotor core structure can be simple and high strength, and the synchronous motor excellent in high-speed operation can be realized.例文帳に追加
このようにすれば、磁路を略鞍状に形成することができるため、必要磁路長を短縮し、ロータコアの構造を簡単かつ高強度とすることができるので、高速回転性能に優れるシンクロナスモータを実現することができる。 - 特許庁
The permanent magnet-type synchronous electric motor holding the permanent magnet 1 in a rotor core is provided with a conductor 2 which surrounds the permanent magnet 1 and reduces eddy current of the permanent magnet 1 and whose conductivity is higher than the that of permanent magnet 1.例文帳に追加
ロータコアの内部に永久磁石1を保持する永久磁石式同期電動機において、永久磁石1を囲んで永久磁石1の渦電流を減少させる永久磁石1よりも導電率の高い導体2を備えた。 - 特許庁
To provide a synchronous motor for timers with new structure that can suppress the amount of heat being generated in a coil and at the same time obtain a stable magnetic pole at the magnetic pole formation part of a stator with less number of turns and simple structure.例文帳に追加
少ないコイル巻線数と簡単な構造をもってコイルの発熱量を抑えることが出来ると共に、ステータの磁極形成部において安定した磁極を得ることの出来る、新規な構造のタイマ用同期モータを提供すること。 - 特許庁
The transmission 10 refers to a two-speed transmission, including a motor 12, an input shaft 14, an output shaft 16, and in order from the input shaft 14 to the output shaft 16, a synchronous mechanism 20, a clutch mechanism 30 and an encyclic-gear mechanism 40.例文帳に追加
変速装置10は、モータ12、入力軸14、出力軸16、そして、入力軸14から出力軸16に向けて順に、シンクロ機構20、クラッチ機構30、遊星歯車機構40が配設されている2段変速の変速装置である。 - 特許庁
To provide a vector control inverter which is excellent in starting performance by increasing the circulation time of a current flowing in a resistor for current detection arranged in an inverter bus, and enabling the current detection and stabilizing a motor current in positioning and synchronous operation.例文帳に追加
インバータ母線に配した電流検出用抵抗に流れる電流の通流時間を増加させ、電流検出を可能にし、位置決め、同期運転における電動機電流を安定させて起動性の良いベクトル制御インバータを提供する。 - 特許庁
To provide an air conditioner capable of preventing degradation of a function of a compressor caused by demagnetization against a current upon a start and during an operation of the compressor driven by a self-start synchronous motor, and to combine equalization of compressor operation time and comfort.例文帳に追加
自己始動式同期電動機にて駆動する圧縮機の起動時及び運転中の電流に対して減磁による圧縮機機能低下を回避し、かつ圧縮機運転時間の平準化と快適性の両立を図った空気調和機を得る。 - 特許庁
To provide a rotor for a permanent-magnet synchronous motor, eliminating the idea for positively contacting the outer surface of the permanent-magnet to the outside core wall part of a core member, in holding the permanent-magnet in the magnet insertion hole of the core member.例文帳に追加
永久磁石をコア部材の磁石挿入孔に保持する際、永久磁石の外面とコア部材の外側コア壁部とを積極的に接触させるという考えを排除した永久磁石同期モータ用回転子を提供することである。 - 特許庁
The controller of a permanent magnet synchronous motor 1 performs V/f control on a rotating coordinate system having a first coordinate axis (δ axis) in the direction of output voltage vector of an inverter 2 and a second axis, i.e., γ-axis, orthogonal thereto.例文帳に追加
インバータ2の出力電圧ベクトルの方向を第1の座標軸(δ軸)とし、これと直交するγ軸を第2の座標軸とする回転座標上でV/f制御を行う永久磁石同期電動機1の制御装置に関する。 - 特許庁
To reduce a harmful influence of an abnormality when the abnormality in the synchronous control of a valve drive system and the rotation of a crank shaft occurs in an internal combustion engine having the valve drive system opening and closing a valve element by, for example, an electric motor.例文帳に追加
例えば電動モータによって弁体を開閉駆動する弁駆動システムを持つ内燃機関において、弁駆動システムとクランク軸の回転との同期制御に異常が発生した場合に、当該異常による悪影響を低減できるようにする。 - 特許庁
To provide a device for presuming initial magnetic pole of an AC synchronous motor capable of outputting maximum torque by minimizing torque loss and of accurately presuming a true value of an initial magnetic pole position, as the operation range is made almost the same as the operation range by command speed.例文帳に追加
動作範囲が指令速度による動作範囲とほぼ同じになり、トルク損失を最小限に抑えて最大トルクを出すことができ、初期磁極位置の真値が正確に推定できるAC同期モータの初期磁極推定装置を提供する。 - 特許庁
Then, when the position detecting means 5 is not disposed at the proper position, the method includes a step of forming a control phase θdc by a position estimator 20 by operating the synchronous motor 1 without position sensor, and estimating the phase at output signal timing of the position detecting means 5.例文帳に追加
そこで、位置検出手段5が適正な位置にない場合、同期モータ1を位置センサレス運転して位置推定部20により制御位相θdc を作成し、これにより位置検出手段5の出力信号タイミングでの位相を推定する。 - 特許庁
A brushless DC motor is controlled wherein control is changed from synchronous control to V/f control, prior to a specific rotation range of a driven body is reached, and a period for increasing frequency control gain K_ω is provided, after the completion of this change.例文帳に追加
被駆動体の特定回転域に達する前に同期制御からV/f制御への切換えを行うようにすると共に、その切換え完了後、周波数制御ゲインK_ωを上昇させる期間を設けてブラシレスDCモータを制御するようにした。 - 特許庁
The parameters included in a model for a system including the synchronous motor and control unit of the same are sequentially estimated, and the motor constant is determined from the estimated parameters, using voltage information based on voltage commands Vd^*, Vq^* that constitute output of the current control means, current information based on detected currents id, iq, position information based on static position of the rotor.例文帳に追加
電流制御手段の出力である電圧指令Vd^*,Vq^*に基づく電圧情報と、検出電流id,iqに基づく電流情報と、回転子の静止位置に基づく位置情報とを用い、同期モータと当該制御装置を含む系のモデルに含まれるパラメータを逐次推定し、推定されたパラメータからモータ定数を求める。 - 特許庁
A power supply facility 12 connected with a power system 11 comprises a power generation facility 1 utilizing natural energy, and the like, and involving variation in generated power, and a power generation facility 2 performing base power generation and having a double power supply synchronous generator including a motor 3 and a variable frequency converter 5 driven by the motor 3.例文帳に追加
電源設備12は、自然エネルギー等を用いた発電を行い、発生電力が変動する発電設備1と、ベースとなる発電を行うとともに、原動機3と原動機3により駆動される可変周波数変換器5を有する二重給電同期発電機を有する発電設備2とを備え、電力系統11に接続されている。 - 特許庁
A motor drive for controlling a permanent magnet synchronous motor has: a magnetic flux control unit 16 for calculating a current command corresponding to a d-axis component of a current flowing in an armature winding as an excitation current command (iγ^*); and a current control unit 15 for controlling the current flowing in the armature winding based on the excitation current command.例文帳に追加
永久磁石同期モータを制御するモータ駆動装置において、電機子巻線に流れる電流のd軸成分に対応する電流指令を励磁電流指令(iγ^*)として算出する磁束制御部16と、励磁電流指令に基づいて前記電機子巻線に流れる電流を制御する電流制御部15と、を備える。 - 特許庁
This method for feeding the weft yarn is provided by using a servomotor responding in a high speed as the motor of controlling the driving part for delivering the weft yarn from the yarn-feeding body, and for sending a weft yarn length of 1 pick against the one rotation of the loom accurately in a high speed by a synchronous ratio operation of the motor with an encoder for detecting the rotation of the loom.例文帳に追加
本発明では横糸を給糸体から、送り出す駆動部分を制御するモータに、高速で応答するサーボモータを使用し、このモータと織機の回転を検出するエンコーダとの同期比率運転により織機1回転に対して1ピックの横糸長さを正確に高速で送り出す方法を提供している。 - 特許庁
When the DC fan motor 6 starts, the controller 3 performs a synchronous operation which outputs from the inverter 5 an exciting pattern for starting, and performs a position detecting operation based on the position detecting signal detected by the position detecting sensor 1, when the current revolutions obtained from the position detecting signal detected by the position detecting sensor 1 during the synchronous operation almost coincides with the revolutions of the output of the inverter 5.例文帳に追加
上記制御部3は、DCファンモータ6の起動時、インバータ部5から起動用励磁パターンを出力する同期運転を行い、その同期運転中に位置検出センサ1により検出された位置検出信号から得られる現在回転数とインバータ部5の出力の回転数が略一致したとき、位置検出センサ1により検出された位置検出信号に基づく位置検出運転を行う。 - 特許庁
A controller 10 judges the locked state of the motor to command the interruption of electric current to an inverter 12, when at least one phase of each phase current of the synchronous machine 3 is equal to or larger than prescribed based on the output signal of current sensors 5, 6, and revolutions are equal to or less than prescribed.例文帳に追加
コントローラ10は、電流センサ5、6の出力信号に基づいて同期機3の各相電流の少なくとも一相が所定値以上で、かつ、回転数が所定値以下の場合に、ロック状態と判定してインバータ12に電流遮断を指令する。 - 特許庁
Then the mean of the numbers of revolution calculated M times is set as the number of revolutions N at the start-up time (S112); the electrical angle calculated last is set as an electrical angle θ at the starting (S114); and using these a normal control of the synchronous motor is started (S116).例文帳に追加
そして、M回に亘って計算した回転数の平均を起動時の回転数Nとすると共に(S112)、最後に計算した電気角を起動時の電気角θとして設定し(S114)、これを用いて同期電動機の通常制御を開始する(S116)。 - 特許庁
The brushless synchronous motor comprises: a rotor 1 having salient magnets 2-5 arranged in the circumferential direction; and a stator 6 having drive magnetic poles 9 applied with an exciting coil 8 and arranged in the circumferential direction wherein the rotor 1 has a noncircular cross-section.例文帳に追加
突極磁石2〜5を周方向に配置した回転子1と、励磁コイル8が巻回された駆動磁極9を周方向に配置した固定子6とを具備するブラシレス同期電動機は、回転子1の断面形状を非円形としたことを特徴とする。 - 特許庁
This PM synchronous motor includes magnet magnetic portions 30, 40 that are formed from a permanent magnet of a rotor and generate magnet torque and a magnetic salient pole portion having low magnetic resistance, and shifts an angle between low magnetic resistance portions 51, 52 more than in the conventional case.例文帳に追加
ロータの永久磁石により形成されてマグネットトルクを発生する磁石磁極部30、40と、低磁気抵抗を有する磁気突極部により構成されて主としてリラクタンストルクを発生する低磁気抵抗部51、52との間の角度を従来よりずらせる。 - 特許庁
In the method of manufacturing the permanent magnet synchronous motor by fixing a stator core within a frame, with a specific portion of the frame and a specific portion of the stator core serving as reference positions, respectively, both areas are positioned with a specific positional relationship and subsequently fixed.例文帳に追加
フレーム内にステータコアを固定することにより永久磁石式同期モータを製造する方法において、フレームの特定部位と、ステータコアの特定部位をそれぞれ基準位置とし、上記両部位を特定の位置関係をもって位置決めした後、固定するようにした。 - 特許庁
To provide an electric vehicle controller by which a cost as a system is reduced, and an outline is made compact by constituting the controller to conduct control close to centralized control like an induction motor, in a vehicle drive system employing permanent magnet type synchronous motors as motors for driving a vehicle.例文帳に追加
永久磁石型同期電動機を車両駆動用電動機に採用した車両駆動システムにおいて、誘導電動機のような集中制御に近い構成にして、システムとしてのコストを低くし、外形を小型化できる電気車制御装置を提供する。 - 特許庁
To provide an elevator door driving device capable of braking an elevator door so as to quickly stop the operating door and so as not to easily open the elevator door at uncontrollable time by constituting an armature short circuit in the elevator door driving device using a permanent magnet synchronous motor.例文帳に追加
永久磁石同期電動機を用いたエレベータドア駆動装置においてアマチュア短絡回路を構成し、制御不能時、動作中のドアを速やかに停止させ、また簡単にエレベータドアが開かないように制動することができるエレベータドア駆動装置を提供する。 - 特許庁
In using the outer rotor type synchronous reluctance motor with such constitution, the shaft of the outer rotor rotates in the bearing of the stator by generation of magnetic resistance of the outer rotor to rotate the outer rotor.例文帳に追加
以上のような構造でアウターロータ型同期リラクタンス電動機を使用するときは,アウターロータの磁気抵抗が発生することによって,アウターロータのシャフトが固定子の軸受の中で回転することで,アウターロータを回すアウターロータ型同期リラクタンス電動機を特徴とする。 - 特許庁
To provide an inexpensive permanent magnet type synchronous motor capable of reducing entire cogging torque by cancelling cogging torque of the same order component as the number of poles, that is resulting from nonuniformity of a stator, with a simple structure and to provide a method of manufacturing the stator thereof.例文帳に追加
この発明は、ステータがもつ不均一性に起因する極数と同じ次数成分のコギングトルクを簡易な構成で打ち消して、全体のコギングトルクを低減させることができる安価な永久磁石式同期モータおよびそのステータの製造方法を得る。 - 特許庁
When the power supply is stopped under the deceleration operation of the permanent magnet synchronous motor 11, torque control is performed to the inverter 10 such that occurrence of brake torque continues, and control is performed such that power generated by the inverter 10 becomes zero.例文帳に追加
永久磁石同期電動機11の減速運転中に電力供給が停止されると、インバータ10に対してブレーキトルクの発生が継続するようにトルク制御を行うとともに、インバータ10の発生する電力が零になるように制御する。 - 特許庁
In a drive unit of the three-phase synchronous electric motor, a rotor is synchronized with a rotating magnetic field generated from a stator coil by using an initial state synchronization control part 53B prior to the execution of a normal drive control part 56, and the charging state of the capacitor 30 is controlled.例文帳に追加
三相交流同期電動機の駆動装置において、通常運転制御部56の実行に先立って、初期状態同期制御部53Bによりステータコイルから発生させる回転磁界にロータを同期させ、かつコンデンサ30の充電状態を制御する。 - 特許庁
The present invention relates to a synchronous motor comprising a cylindrical rotor (4) provided with permanent magnets (3) located inside a cylindrical stator provided with a winding (U, V, W), characterized in that the rotor is provided with protuberances (41) facing the winding.例文帳に追加
本発明は、巻き線(U,V,W)が設けられた円筒形ステータの内側に配置された永久磁石(3)を備えている円筒形ロータ(4)を具備した同期モータであり、ロータには巻き線に面した突起(41)が設けられていることを特徴としている。 - 特許庁
To provide a disk storage device capable of generating a synchronous clock having the accuracy of synchronization with a disk medium heightened by taking control characteristics of a spindle motor into consideration to improve the following accuracy of the disk medium to a rotational speed during a write operation.例文帳に追加
ライト動作時に、スピンドルモータの制御特性を考慮することで、ディスク媒体の回転速度に対する追従精度を向上させて、ディスク媒体に対する同期精度を高めた同期クロックを生成できるディスク記憶装置を提供することにある。 - 特許庁
To provide an electric vehicle controller by which a system cost is reduced and an outline is made compact by constituting the controller to conduct control close to centralized control as in an induction motor, in a vehicle drive system employing permanent magnet type synchronous motors as motors for driving a vehicle.例文帳に追加
永久磁石型同期電動機を車両駆動用電動機に採用した車両駆動システムにおいて、誘導電動機のような集中制御に近い構成にして、システムとしてのコストを低くし、外形を小型化できる電気車制御装置を提供する。 - 特許庁
This dynamo-electric machine employs a rotary shaft coupling mechanism 900, which couples separably a rotary type DC/AC converter (rotary inverter) for realization of mechanical DC/AC conversion to a rotary motor for vehicle for sending and receiving an AC output, in order to enable synchronous rotation at the desired relative angle position.例文帳に追加
機械的に直交変換する回転型直交変換部(ロ−タリ−インバータ)を、交流出力を授受する車両用回転電機に所望相対角度位置で同期回転可能、かつ、解離可能に連結する回転軸連結機構900を採用する。 - 特許庁
To provide a permanent magnet synchronous motor which detects a magnetic pole position with excellent precision at high speed, reduces the size by integration of the rotary plate of an encoder with a rotor and measures a rotor temperature, and to provide a magnetic pole position detecting method therefor.例文帳に追加
高速、高精度で磁極位置を検出できると共に、エンコーダの回転板とロータを一体化することで小型化を図り、更に、ロータ温度を測定することができる永久磁石型同期電動機及びその磁極位置検出方法を提供する。 - 特許庁
To provide a synchronous motor drive system comprising means for realizing a vector control type sensorless system by controlling from a low speed region to a high speed region through a continuous method while stabilizing the control system without superposing harmonics or increasing noise.例文帳に追加
高調波などを重畳することなく、制御系統を安定させ、騒音を増大させず、低速域から高速域までを連続した方法により制御し、ベクトル制御型センサレス方式を実現する手段を備えた同期電動機駆動システムを提供する。 - 特許庁
The stator 10 for constituting the stator section 2 of a three-phase synchronous motor 1 includes a first back yoke 6 having twelve teeth 5 provided on an inner periphery, and a second back yoke 7 radially lap wound on the outer peripheral surface of the first back yoke 6.例文帳に追加
三相同期モータ1の固定子2を構成するステータ10は、12個のティース部5が内周部に設けられる第1バックヨーク部6と、この第1バックヨーク部6の外周面に径方向に巻き重ねて設けられる第2バックヨーク部7とから構成されている。 - 特許庁
To facilitate its control by reducing the drive frequency of a necessary inverter and to improve durability to the high-speed revolution of a shaft by relieving the stress due to centrifugal force working on a rotor, in a permanent magnet synchronous motor.例文帳に追加
永久磁石同期モータにおいて、必要とされるインバータの駆動周波数を低減させることによって制御を容易とすると共に、ロータに作用する遠心力による応力を緩和することによってシャフトの高速回転に対する耐久性を向上させる。 - 特許庁
In a power generation mode where a generator-motor 6 generates power and a diode element 4 rectifies it, a synchronous commutation gate signal generating circuit 12 detects conductive ones out of diode elements 4, based on the output signal of a current sensor 11 loaded in the AC power line of the generator-motor 6, and turns on a switching element 3 connected in parallel with the diode element 4.例文帳に追加
発電電動機6で発電しダイオード素子4で整流する発電モードにおいて、発電電動機6の交流電力線に装荷した電流センサ11の出力信号に基づいて、同期整流ゲート信号発生回路12により、ダイオード素子4のうち導通状態にあるものを検出して、そのダイオード素子4に並列接続されたスイッチング素子3をオンさせる。 - 特許庁
In the permanent-magnet synchronous motor, a first groove 11 and a second groove 22 are provided respectively at surfaces where the iron core of a stator 10 and a rotor 20 face with each other, thus setting a second region less affected by an opponent side than by an ordinary flux.例文帳に追加
永久磁石型同期電動機における固定子10の鉄芯と回転子20において互いに対向し合う面にそれぞれ第1の溝11、第2の溝22を設けることで相手側からの磁束が通常の磁束より低く作用する第2の領域を設定する。 - 特許庁
In the self-starting type permanent magnet synchronous electric motor including a stator with a stator winding, a basket-shaped winding and a permanent magnet provided to a rotor core, a torque component generated by the basket-shaped winding reaches its maximum at one within a slip value range of 0 to 1.例文帳に追加
固定子巻線を備えた固定子と、回転子鉄心にかご型巻線と永久磁石とを備えた自己始動型永久磁石同期電動機において、前記かご型巻線が発生するトルク成分が、すべり0〜1の範囲において1で最大となることを特徴とすること。 - 特許庁
The generating part of a controller 18 estimates the current value of AC power in a period, when the rotor of a synchronous motor 10 rotates as least once, based on the current value of AC power that an I/O 30b receives after an I/O 30a outputs a PWM wave signal.例文帳に追加
制御装置18の生成部は、I/O30aがPWM波形信号を出力した後にI/O30bが受付けた直流電力の電流値に基づいて、同期モータ10のロータが少なくとも1回転する期間における交流電力の電流値を推定する。 - 特許庁
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|