1153万例文収録!

「power-OFF」に関連した英語例文の一覧と使い方(195ページ目) - Weblio英語例文検索


小窓モード

プレミアム

ログイン
設定

設定

Weblio 辞書 > 英和辞典・和英辞典 > power-OFFの意味・解説 > power-OFFに関連した英語例文

セーフサーチ:オン

不適切な検索結果を除外する

不適切な検索結果を除外しない

セーフサーチについて

power-OFFの部分一致の例文一覧と使い方

該当件数 : 10399



例文

In a color printer 100, the saw tooth-wave superposed bias to intermittently change a potential difference between the center value of the electrifying bias of an electrifying device 3 and Vdc of the developing bias of a developing device 4 is superposed on the developing bias of the developing device 4 when an image is not formed such as just after turning off a power source.例文帳に追加

カラープリンタ100は,電源投入直後などの非画像形成時,現像装置4の現像バイアスに,帯電装置3の帯電バイアスの中心値と現像バイアスのVdcとの電位差を断続的に変化させるノコギリ波の重畳バイアスを重畳させる。 - 特許庁

When a hold switch is in an on-state, a play key 11 is turned on, a power source Vdd of a microcomputer is turned on by linking, after an initial setting period elapses, as it is confirmed that the play key is turned off by testing the play key 11, after the prescribed period Tw, a control output 1A of the microcomputer is about to be started.例文帳に追加

ホールドスイッチがオンである場合、プレイキー11がオンになると、連動してマイコン電源Vddがオンし、初期設定期間経過後にはプレイキー検査をすると、すでにプレイキー11はオフとなっているので、所定期間Tw待って、マイコン制御出力1Aを立ち上げようとする。 - 特許庁

When a DC power source 17 supplied to a control circuit 24 is cut off, the voltage across the filter capacitor 3 in a main circuit 15 is divided by a voltage-divider resistor 4, and a gate voltage for operating a semiconductor switching element 9 in the discharge circuit 10 is supplied via a diode 5.例文帳に追加

制御回路24に供給されている直流電源17が遮断された時、主回路15の平滑コンデンサ3の両端電圧を分圧抵抗4で分圧し、ダイオード5を経由して放電回路10の半導体スイッチング素子9が動作するゲート電圧を供給する。 - 特許庁

When one unused side out of the insertion port 11a dedicated to the on-timer operation and the insertion opening 11c dedicated to the off-timer operation is previously covered with the opening cover 61, the plug for power is prevented from being inserted into the wrong insertion port 11a or 11c.例文帳に追加

予め、オンタイマ動作専用の栓刃挿入口11aとオフタイマ動作専用の栓刃挿入口11cとのうち使用しない一方を栓刃挿入口カバー61によって覆っておけば、電源用プラグが誤った栓刃挿入口11a,11cに挿入されることを防止することができる。 - 特許庁

例文

When determining that the second communication terminal device (2) cannot connect to a communication network because being outside the service area or power-off, a first communication terminal device (1) intermittently transmits a call origination request to the second communication terminal device (2) to repeat transmission of the call origination request.例文帳に追加

第2の通信端末装置(2)が圏外または電源オフなどにより通信網と接続不可な状態であると第1の通信端末装置(1)が判断した際に、発呼要求を第2の通信端末装置(2)に間欠で送信し、発呼要求の送信を繰り返す。 - 特許庁


例文

To prevent an RFID tag from getting damaged by power-off or the removal operation of a replacement parts during the writing of data in an image forming device on which the replacement part with a passive type RFID tag is detachably mounted and to form an image on a recording medium by using the replacement part.例文帳に追加

パッシブ型のRFIDタグを備えた交換部品が着脱可能に装着され、当該交換部品を用いて記録媒体に画像を形成する画像形成装置において、データ書き込み中の電源オフ操作や交換部品の取り外し操作によるRFIDタグの破壊を防止する。 - 特許庁

To provide a video audio signal processing apparatus wherein a main body side can perform ON / OFF control of the power supply of an external device and to provide a video audio signal processing apparatus wherein a main body side can display information of broadcast contents and make channel selection operations as to a channel signal received by an external tuner.例文帳に追加

本体側から外部機器の電源のオン・オフ制御ができる映像音声信号処理装置、及び、本体側から外部チューナーが受信するチャンネル信号について放送内容の情報の表示及び選局操作ができる映像音声信号処理装置を提供する。 - 特許庁

Even when the power supply voltage of the circuit is a high voltage of 100 V or more, only such a low voltage as an extent of the voltage between terminals of the LEDs 1-8 which are the light emitting element A or the conduction voltage of the transistor Q1 is applied on the on/off circuit E incorporated in the pilot light.例文帳に追加

このため、回路の電源電圧が100V以上の高い電圧であっても、本発明の表示灯に内蔵された点滅回路Eには、発光体素子AであるLED(1−8)の端子間電圧またはトランジスタQ1の導通電圧程度の低い電圧しか印加されない。 - 特許庁

Coils L1 and L2 for outputting alternating fields, a driving circuit 44 for driving these coil L1 and L2, a battery 45 for supplying power to this driving circuit 44 and a switch 43 for turning on/off the driving circuit 44 are attached onto a base 40a inside a case 41.例文帳に追加

ケース41の内部の底面40a上には交番磁界を出力するコイルL1,L2と、これらのコイルL1,L2を駆動する駆動回路44と、この駆動回路44に電源を供給する電池45と、駆動回路44をON・OFFするスイッチ43とが取付けられている。 - 特許庁

例文

To decide the input path of a video and a voice signal to be input to a display device, and to control the power ON/OFF of repeater equipment based on the determination result in an AV system equipped with repeater equipment such as an AV amplifier and a display device HDMI connected to the repeater equipment.例文帳に追加

AVアンプ等のリピータ機器と、リピータ機器とHDMI接続された表示装置とを備えるAVシステムにおいて、表示装置に入力される映像及び音声信号の入力経路を判定し、その判定結果に基づいてリピータ機器の電源オン/オフを制御する。 - 特許庁

例文

By invalidating the volatile memory 52 to the accompaniment of turning-off of a main body power supply or passage of a predetermined period of time, input of the decoding key is required when reproducing encrypted images stored in storage media 202 and 212, so that the security of the photographed images can be protected.例文帳に追加

揮発性のメモリ52を本体電源のオフや所定期間の経過に伴って無効化されるようにすることで,記憶媒体202,212に記憶された暗号化画像の再生をする場合には,改めて復号鍵の入力が必要となるので,撮影画像の機密を保持することができる。 - 特許庁

To provide a lightweight connection sleeve for a diamond wire saw which is used for cutting stone, concrete or the like, less liable to cracks, has high wire rope holding power so that a wire rope is less liable to fall off therefrom, and less liable to cause disaster even if it is separated from the wire rope.例文帳に追加

石材やコンクリートなどの切断に用いられるダイヤモンドワイヤソーの接続スリーブであって、クラックが入りにくく、ワイヤロープ保持力が大きく、接続スリーブからワイヤロープが抜けにくく、軽量で、接続スリーブが万一ワイヤロープから外れた場合でも災害を起こしにくい接続スリーブを提供する。 - 特許庁

The level shifter 301 controls electric potentials input to the back gates BG of the transistors Tr312 and Tr315 using input signals V_BG, /V_BG, and sets a threshold voltage Vth_OFF of the transistors Tr312 and Tr315 in off-state to be larger than a low level-low potential power VEE of the input signals 01, /01.例文帳に追加

レベルシフタ301は、トランジスタTr312,315のバックゲートBGに印加する電位を入力信号V_BG,/V_BGを用いて制御し、オフの状態にあるトランジスタTr312,315の閾値電圧Vth_OFFを、入力信号01,/01のLowレベル−低電位電源VEEよりも大きくする。 - 特許庁

An inverter circuit part INV supplies power to a load circuit 1 through a leakage transistor LT1 by converting a DC voltage of a smoothing capacitor C1 into a high frequency voltage with switching elements Q1, Q2, and on/off of the switching elements Q1, Q2 is controlled with a control circuit part 2.例文帳に追加

インバータ回路部INVは、平滑コンデンサC1の直流電圧をスイッチング素子Q1,Q2でスイッチングして高周波電圧に変換し、リーケージトランスLT1を介して負荷回路1に電力を供給しており、スイッチング素子Q1,Q2のオン/オフは制御回路部2によって制御される。 - 特許庁

To provide a remote management system of an image forming device which is provided with a function with which a communication terminal connected to one of operating image forming devices collectively sends report information including even the report information of image forming devices in a power-off state to a centralized management device at the time of periodical reporting.例文帳に追加

定時通報時に稼働中の画像形成装置のうちの1台に接続された通信端末が電源オフの画像形成装置の通報情報も一括して集中管理装置に送る機能を備えた画像形成装置の遠隔管理システムを提供する。 - 特許庁

To provide an automatic print system, an automatic print method, a server and a printer capable of dealing with a case that an image photographed by an electronic camera can not be printed since a power source of the printer is turned off or ink or paper in the printer are exhausted when automatically printing the image on a remote site.例文帳に追加

電子カメラで撮影した画像を遠隔地にいても自動的にプリントする際にプリンタの電源がオフであったりプリンタのインク、用紙がなくなっていたためにプリントできない場合に対処可能な自動プリントシステム、自動プリント方法、サーバ及びプリンタを提供する。 - 特許庁

A motor control part P installed in an ECU 106 of an electric power steering device is provided with the chopper circuit 103 for carrying out booster operation, a failure detection circuit 12 for detecting failure of a first switching element TR1 in the chopper circuit 103, and a shut off relay switch 14.例文帳に追加

電動パワーステアリング装置のECU106に設けられるモータ制御部Pは、昇圧動作を行うチョッパ回路103と、チョッパ回路103内の第1のスイッチング素子TR1の故障を検出する検出検出回路12と、遮断用リレースイッチ14とを備えている。 - 特許庁

To improve workability and to reduce cost without lowering the reliability of engagement because of needing to connect only one point to an input terminal in circuit connection by the common use of a power supply of a magnet switch and a motor while performing engagement and on/off operation of a main contact.例文帳に追加

メイン接点のON、OFFと噛み合いを行わせつつ、該マグネットスイッチとモータの電源を共通使用しているので、回路の結線は入力端子に1カ所つなげばよいので噛み合いの信頼性を落とすことなく、作業性の向上とコストを下げることを目的としている。 - 特許庁

To obtain an electronic circuit breaker that outputs a trip signal for actuating a tripper in a timely manner without delays and will not be degraded in cut-off performance; even when a make-and-break contact is turned on, to start up a power supply device with a short circuit trouble, present in the electric circuit.例文帳に追加

電路において短絡事故が発生した状態で開閉接点をONさせて電源装置を立上げた場合においても、引き外し装置を動作させるトリップ信号を遅延することなくタイムリーに出力し、遮断性能が低下することのない電子式回路遮断器を得る。 - 特許庁

In this case, an emergency situation is recognized when the speed of the vehicle is not reduced even if the brake pedal is depressed, a power system including an electronic control unit for controlling an engine is switched from an on-state to an off-state based on the recognition (steps S206, S208 and S209).例文帳に追加

ここで、ブレーキペダルが踏み込まれているにもかかわらず車両が減速していなければ緊急事態であると認識され、この認識に基づいてエンジンを制御する電子制御ユニットを含む電源系統がオン状態からオフ状態に切り換えられる(ステップS206、S208、及びS209)。 - 特許庁

A power-down switch 71 is provided between the reference voltage source 1 and resistor string 2, a switch group 111 for actuation is brought under on/off control based upon the actuation pulse signal 10 of an actuation pulse signal generating circuit 9, and a charging path for charging directly from the reference voltage source 1 at the start is provided.例文帳に追加

パワーダウンスイッチ71を基準電圧源1と抵抗ストリング2との間に設け、起動用スイッチ群111を、起動パルス信号発生回路9の起動パルス信号10でオン・オフ制御し、起動時に基準電圧源1から直接充電する充電経路を設けるようにした。 - 特許庁

In this waveform output device, each of PMOS transistors 21, 22 is successively turned 'OFF' to vary the resistance value between a PMOS transistor 23 and a power source VDD, and, on the basis of the varied resistance value, the amplitude of a waveform at a connecting point between the transistor 23 and an NMOS transistor 31 is controlled.例文帳に追加

PMOSトランジスタ21,22のそれぞれが順次OFFになることにより、PMOSトランジスタ23と電源VDDとの間の抵抗値が可変し、可変した抵抗値に基づいて、PMOSトランジスタ23とNMOSトランジスタ31との接続点における波形の振幅が制御される。 - 特許庁

The mixing condition indicator 1 of ready-mixed concrete is so set that it repeatedly turns lights on and off by corresponding to variations in flucturating value per unit time of load power value for a mixer 6 mixing concrete components, and it is constituted by having an indicating means 4 with a variable lighting time.例文帳に追加

生コンクリートの混練状態表示装置1は、コンクリート構成材料を混練するミキサ6の負荷電力値の単位時間あたりの変動値の変化に対応して点滅を繰り返すように設定されており、かつその点灯時間が可変である表示手段4を備えて構成される。 - 特許庁

An operation signal output part 17 outputs a time-division control type operation signal to respective heaters H11-H33 of individual zones Z1-Z3 on the basis of the load rate to turn on/off power supply currents to be supplied to the heaters H11-H33 of respective zones Z1-Z3.例文帳に追加

操作信号出力部17は、個々のゾーンZ1〜Z3内の複数のヒータH11〜H33に対し、その負荷率に基づき時分割制御方式の操作信号を出力して各ゾーンZ1〜Z3のヒータH11〜H33へ供給される電源電流をオンオフ操作する。 - 特許庁

When a communication apparatus (100) receives a power-OFF command from an external device (200) connected via a connecting cable (300), until a predetermined period of time is elapsed, a CEC command from the external device (200) can be received, without invalidating a CEC line (302).例文帳に追加

通信装置(100)が接続ケーブル(300)を介して接続された外部装置(200)から電源OFFコマンドを受信した場合、所定期間が経過するまでの間は、CECライン(302)を無効にせずに、外部装置(200)からのCECコマンドを受信できるようにする。 - 特許庁

However, when the temperature of a temperature sensing diode 90 is low, an output signal from a hysteresis comparator 94 serves as a logical "L" signal, then the final signal output to a drive IC 60 through an AND circuit 98 serves as a logical "L" signal, preventing the forcible turn-off operation of the power switching element Sw.例文帳に追加

ただし、感温ダイオード90の温度が低い場合、ヒステリシスコンパレータ94の出力信号が論理「L」となるため、AND回路98を介して駆動IC60に出力される最終的な信号は、論理「L」となり、パワースイッチング素子Swの強制的なオフ操作はなされない。 - 特許庁

FETs 114, 115, 124 and 125 in a side in which signal power is impressed when the switching unit is in the off-state are made to have the largest resistance values in the gate bias resistances 134, 135, 144 and 145 connected with the gate electrodes among FETs included in each switching unit.例文帳に追加

各スイッチ部に含まれるFETのうち、スイッチ部がオフ状態であるときに信号電力が印加される側のFET114、115、124及び125については、ゲート電極に接続されるゲートバイアス抵抗134、135、144及び145の抵抗値を最も大きくする。 - 特許庁

With an electronic apparatus that achieves positioning acceleration (hot start) at the next start-up of a host device by periodically performing positioning by a GPS reception part as background positioning during the period in which the power source of the host device driven by a battery is set off, execution of the background positioning is restricted.例文帳に追加

バッテリ駆動のホスト装置の電源がオフとされている期間中にGPS受信部による測位を裏測位として定期的に実行することによりホスト装置の次回起動時における測位高速化(ホットスタート)を実現する電子機器において、裏測位の実行に制限を加える。 - 特許庁

When both setting switches A and B are off, a second solenoid valve 15 for opening a first stop valve 31c and a second stop valve 31d is driven to close an inner pipeline 4, a pump 23 is stopped, and power supply between the electrodes 29a and 29b is stopped.例文帳に追加

設定スイッチA、B共に“OFF”であれば、第1開閉弁31c、第2開閉弁31dを共に開状態に制御する第2電磁弁15を駆動して内部配管14を閉塞し、ポンプ23の駆動停止及び電極29a、29b間への給電停止を行う。 - 特許庁

To provide a combination camera capable of switching a DSC lens into a closing state even if power is applied in a DVC mode after the combination camera is turned off when the DSC lens has been open and to provide a DSC lens control method using the same.例文帳に追加

複合撮影装置のDSCレンズが開放状態で複合撮影装置の電源が遮断された後にDVCモードで電源が印加される場合にも、DSCレンズを閉鎖状態に転換させることのできる複合撮影装置及びそれを利用したDSCレンズ制御方法を提供する。 - 特許庁

On the other hand, when a state of the power supply of the set is in an off state, that is, application of the voltage of the level Vcc is stopped, a signal received at the input terminal 11 is throughout outputted from the output terminal 12, but not outputted from the output terminal 17 (distribution is inhibited).例文帳に追加

一方、セットの電源の状態がオフ状態の場合、即ち、レベルVccの電圧の印加が停止した場合、入力端子11に入力された信号は、スルーアウトして出力端子12から出力されるが、出力端子17からは出力されなくなる(分配が禁止される)。 - 特許庁

Before measuring the output voltage Vout of an IC 10 to be measured, a reference voltage Vref from a high-accuracy reference power source 2 is measured with a voltmeter 7 by turning a switch SW1 off to make it into an interrupted state, and turning a switch SW2 on to make it into a conducting state.例文帳に追加

被測定IC10の出力電圧Voutの測定を行う前に、スイッチSW1をオフさせて遮断状態にすると共にスイッチSW2をオンさせて導通状態にし、高精度基準電源2からの基準電圧Vrefを電圧計7で測定する。 - 特許庁

This temperature controller 12 for controlling temperature of the heating body 11 using a DC power supply changes a length of a time of ON and a length of a time of OFF of the heating body 11 in a specific frequency such that the lengths are different from each other to control the temperature of the heating body 11.例文帳に追加

本発明は、直流電源を使用する発熱体11の温度を制御するための温度制御装置12であって、特定の周波数において発熱体11のオンの時間とオフの時間の長さが異なるように変化させて発熱体11の温度を制御することを特徴とする。 - 特許庁

While turning power supply to loads 12-14 off and charging a battery 6 with a constant current, battery voltage 6a is measured, while raising precision at a detecting section 16, when the battery voltage is in the vicinity of full charge voltage; and then the measured voltage is recorded in a measurement data storage memory 19 (voltage before the change).例文帳に追加

負荷である12〜14への電源供給をオフにし、電池6に定電流充電を行いつつ、電池電圧が満充電近辺の範囲にある時に、検出部16の精度を上げて電池電圧6aを測定し測定データ記憶メモリ19に記録する(変移前電圧)。 - 特許庁

A control unit 81 of a vehicular seat belt device 30 is transferred to the waiting state of the low power consumption when an ignition switch 51 is changed from ON-state to OFF-state, and then, returned from the waiting state to the operating state when at least one of a plurality of return conditions is satisfied.例文帳に追加

車両用シートベルト装置30の制御部81は、イグニションスイッチ51がオン状態からオフ状態に変化したときに、低消費電力となる待機状態に移行し、その後に、複数の復帰条件の少なくとも1つを満足した場合に、待機状態から作動状態に復帰する。 - 特許庁

To provide a small type laser multistage amplifier at a low price using a compact shutter by reducing the cooling power of the shutter, by a method wherein a laser beam is shut off by a shutter and the output of the laser beam entering into the shutter is reduced.例文帳に追加

レーザ多段増幅装置においては、レーザ光をシャッタにより遮断した場合、シャッタに吸収される熱量が大きいためシャッタの強制冷却が必要になり、特にレーザ光の出力が大きくなると、シャッタの冷却部を大きくしなければならず、装置が大型化しコストが高くなる。 - 特許庁

Thereby, a laser beam 40 emitted from the high power laser beam source 42 of the exposure head 14 is turned on and off, an exposure object 10 is exposed in an X axial direction by pixel unit of almost the same number as the number of GLV elements, and then scanned and exposed in the Y axial direction by one line.例文帳に追加

これにより露光ヘッド14の高出力のレーザ光源42から出射されるレーザ光40がオンオフされて、露光対象物10がX軸方向にGLV素子の数と略同数の画素単位で露光されると共に、Y軸方向に1ライン分走査露光される。 - 特許庁

Then the occurrence of an overcurrent to the IC 1 is monitored by means of a current detecting resistor 4 and an overcurrent detecting circuit 5, and when an overcurrent occurs, the power switch 8 is turned off by means of a switch control section 6 and the gates 9 and 10 are set to the second state by means of a gate control section 11.例文帳に追加

そして、電流検出用抵抗4および過電流検出回路5によりIC1への過電流の発生を監視し、過電流が発生した場合にスイッチ制御部6が電源スイッチ8をOFFするとともに、ゲート制御部11がゲート部9,10を第2状態とする。 - 特許庁

A determination part 40a of a controller 40 determines whether respective contacts 48, 50 interlocking with a lifting operation button 30 have been switched based upon whether contact circuits 52, 54 of two systems have been supplied with electric power corresponding to one operation (ON operation or OFF operation) on the lifting operation button 30.例文帳に追加

制御装置40の判定部40aにおいて、昇降操作ボタン30に対する1つの操作(ON操作又はOFF操作)に対応した、2系統の接点回路52、54の通電の有無に基づき、昇降操作ボタン30に連動する各接点48、50の切替えの真偽が判定される。 - 特許庁

The wiper drive circuit 11 is equipped with a delay circuit 31 for delaying opening operation of a drive switch 22 when the wiper switch SW is turned off with respect to the wiper drive circuit 11 equipped with the drive switch 22 for opening and closing a power feeding path of the wiper motor 14 through operation of the wiper switch SW.例文帳に追加

ワイパスイッチSWの操作を通じてワイパモータ14の給電経路を開閉する駆動スイッチ22を備えてなるワイパ駆動回路11に対し、ワイパスイッチSWがオフ操作された場合、駆動スイッチ22の開動作を遅延させる遅延回路31を備えた。 - 特許庁

At the time of standing by for the original reading of the image reader, a motor driving power source is turned off and also a circuit including the coil is set to a closed (on) state so that one or more phases of the coil conduction of the motor 8 may be performed as to the phase switching signals S1 to S4 of a driving control board 21.例文帳に追加

画像読取装置の原稿読み取り待機時には、モータ駆動電源をオフするとともに、駆動制御板21の相切換え信号S1〜S4においてステッピングモータ8のコイル導通が1相以上ある状態になるようにコイルを含む回路を閉(オン)状態にする。 - 特許庁

To provide a vehicular anti-theft device using a battery capable of preventing a vehicle from being stolen by using a control circuit which shuts off the power supplying to the outside from the vehicle battery when a thief intrudes into the vehicle and is going to start the engine, and thereby disabling the engine to start.例文帳に追加

制御回路により、窃盗犯が車内に侵入してエンジンを始動しようとする場合に、自動車のバッテリーによる対外的な電源供給を遮断し、エンジンを始動不能として自動車の盗難を防止できるバッテリーを利用した車両盗難防止装置を提供すること。 - 特許庁

A damper autonomously operated or a self-closing damper operated by power is mounted to shut off an air ventilation flue after the operation of the air conditioning device is stopped, with respect to a pathway having a direct opening to the external among air conditioning and ventilating ducts equipped in the building.例文帳に追加

建物に設備された空調・換気ダクトのうち、外部に直接の開口をもつ経路のものに対して、空調機器運転停止後に空気の通風路を遮断するため、自立式に動作するダンパーまたは動力によって作動する自動閉鎖ダンパーをとりつける。 - 特許庁

To provide a particle movement type display device in which image display is maintained for a long period of time as it is in writing and can follow up an image signal of a source without breaking off, and a little time and power consumption are required for holding gradations compared with reset and re-writing.例文帳に追加

画像表示が書き込み時のままに長期間維持されて、ソースの画像信号に対して途切れることなく画像表示が追従でき、リセット、再書き込みに比較すれば階調保持に要する時間も電力消費もごくわずかで済む粒子移動型表示装置を提供する。 - 特許庁

A traffic light for a road includes a solar panel 6 and an engine generator 44 and also includes a storage battery 43 and a power supply controller 46 connected to the solar panel 6 and engine generator 44, in which a signal display unit 50 can be turned on/off from the storage battery 43 via a signal controller 35.例文帳に追加

ソーラーパネル6及び、エンジン発電機44を備え、ソーラーパネル6及びエンジン発電機44とつながる蓄電池43と電源制御46を有し、この蓄電池44から信号制御部35を介して信号表示機50を点灯,消灯することを可能にした道路用信号機。 - 特許庁

The operation part 81 can perform the lifting and lowering of the ground-leveling device 51 through a link 92 connected to an operation lever 85 and an interlocked arm 66, and the on/off operation of a clutch 73 to transmit driving power to the ground-leveling device 51 through a wire 100 connected to the operation lever 85.例文帳に追加

操作部81は、操作レバー85に連結したリンク92及び連係アーム66を介して整地装置51を上下動できると共に、操作レバー85に連結したワイヤ100により整地装置51に動力を伝達するクラッチ73を入切操作できる。 - 特許庁

To provide a magnetic tape and a magnetic tape cartridge excellent in servo control when reproducing that the reproduced output power hardly drops by off-tracking even if the recording track width is 28 μm or less and the width ratio (recording track width-reproducing track width) is 16 μm or less (especially 10 μm or less).例文帳に追加

記録トラック幅が28μm以下で、[(記録トラック幅)−(再生トラック幅)]が16μm以下(特に10μm以下)と狭い場合であっても、オフトラックによる再生出力の低下が生じにくいサーボ特性に優れた磁気テープおよび磁気テープカートリッジを提供する。 - 特許庁

When detecting an off-state of an audio switch 54 after a specific time, it is determined not as the idling stop state but as leaving an key at an ACC (accessory) position and power supply to the amplifier 22 is stopped and the battery 40 is prevented from running out due to bias current consumption of the amplifier 22.例文帳に追加

また、前記一定時間後にオーディオスイッチ54のオフ状態を検出したときには、アイドルストップではなくACC位置でのキー放置と判断して増幅器22への電気の供給を停止し、増幅器22のバイアス電流消費によるバッテリ40の上がりを防止する。 - 特許庁

Then, when the engine speed exceeds a second set value and if set time has passed since counting by the timer 101a was started, the ECM 101 outputs a signal to the general load relay 117 and performs closing operation, so as to release shut-off of the power supply to the general load 116.例文帳に追加

その後、エンジン回転数が第2の設定値以上となり、さらにタイマー101aによるカウント開始から設定時間が経過していれば、一般負荷用リレー117に信号を出力して閉操作することで、一般負荷116に対する電力供給の遮断を解除する。 - 特許庁

例文

A level of an on-signal output from the threshold circuit 25 is converted by the buffer circuit 29 into a higher voltage than a threshold of the transistor 26 used for pulldown and thereby even if a level of the gate signal is low, the transistor 26 used for pulldown certainly operates to turn off the power semiconductor element 24.例文帳に追加

しきい値回路25から出力されるオン信号のレベルがバッファ回路29でプルダウン用トランジスタ26のしきい値よりも高い電圧に変換されることによって、ゲート信号のレベルが低くても、プルダウン用トランジスタ26が確実に動作し、パワー半導体素子24がオフ状態となる。 - 特許庁




  
Copyright © Japan Patent office. All Rights Reserved.
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する
英→日 日→英
こんにちは ゲスト さん

ログイン

Weblio会員(無料)になると

会員登録のメリット検索履歴を保存できる!

会員登録のメリット語彙力診断の実施回数増加!

無料会員に登録する

©2026 GRAS Group, Inc.RSS