| 例文 |
value sourceの部分一致の例文一覧と使い方
該当件数 : 3177件
When an operator selecting the set value turns on a power source switch and rotates a set key switch to an ON position, whether or not the number of rotation of a cooling fan after the power source switch of the slot machine is turned on until it shifts to a setting change mode exceeds N rotation is determined.例文帳に追加
設定値の選択を行う作業者が電源スイッチをオンするとともに設定キースイッチのオン位置に回動した場合、スロットマシンの電源スイッチがオンされてから設定変更モードに移行するまでの冷却ファンの回転数がN回転を超えたか否かを判定する。 - 特許庁
Data stored in the work areas other than the set-value work area of the RAM are not cleared only by turning on the power source while turning on the setting key switch, however, the data are cleared on condition that the power source is turned on while the data clear switch, besides the setting key switch, is turned on.例文帳に追加
RAMの設定値ワーク以外のワークに記憶されているデータは、単に設定キースイッチをON状態としつつ電源をONだけではクリアされず、設定キースイッチに加えてデータクリアスイッチもON状態として電源をONしたことを条件としてクリアされる。 - 特許庁
A detection circuit 10, a switch T and an alarm unit 11 are provided as a safety means, so as to break a commercial electric power source E to an X-ray tube power source XP and to alert by the alarm unit 11, when outputs of the inlet side sensor S1 or the outlet side sensor S2 exceed a threshold value.例文帳に追加
また安全手段として検出回路10、スイッチT、警報機11を設け、入口側センサS1、出口側センサS2の出力がしきい値を越えた場合に、X線管電源XPへの商用電源Eを遮断するとともに、警報機11により警報を発令する。 - 特許庁
The floor heating controller demands supply of low temperature water (40-45°C) to the heat source unit when the room temperature becomes a predetermined value higher than the set temperature in a normal operation state of supplying hot water of a reference temperature (60°C) to the floor heating terminal from the latent heat recovery type heat source unit.例文帳に追加
床暖房コントローラは、潜熱回収型熱源機から床暖房端末に基準温度(60℃)の温水が供給されている通常運転状態で、室温が設定温度よりも所定値高くなると、熱源機に低温水(40〜45℃)の供給を要求する。 - 特許庁
Lighting modes of the lighting system contain two lighting modes of a light source 1, or a first state and a second state, and when a lighting mode of an auxiliary light source 2 is included, contain three lighting modes, and a lighting mode with a minimum value of optical output of the lighting system is the miniature bulb mode.例文帳に追加
照明装置として持つ点灯モードは、光源1の点灯モードが第1状態、第2状態の2つで、補助光源2の点灯モードを含めると3つの点灯モードからなり、照明装置の光出力の最小値を有する点灯モードは豆球モードである。 - 特許庁
The alarm 1 is provided with: a current detection part 13 for detecting output current of a battery power source; and a control unit 14 for referring to the current detection part at a prescribed timing and reporting a failure of the alarm when the output current of the battery power source is larger than a prescribed value.例文帳に追加
警報器1は、電池電源の出力電流を検出する電流検出部13と、電流検出部を所定のタイミングで参照して、電池電源の出力電流が前記所定値よりも大きければ、警報器の故障を報知させる制御部14とを備えている。 - 特許庁
The device has a means for detecting output power of each exciting light or a means for detecting signal light output power of a wavelength in which gain by each exciting light source is made maximum, and a means 4 for controlling a drive current of each exciting light source keeping power at a constant value.例文帳に追加
各励起光の出力パワーを検出する手段又は各励起光源による利得が最大となる波長の信号光出力パワーを検出する手段を持ち、パワーを一定値に保つよう各励起光源の駆動電流を制御する手段4を持つ。 - 特許庁
A burst signal controlling part 13a is equipped with a voltage detecting feature of a power source battery and a feature to control duty ratio of a burst signal, the output current of an inverter circuit 12 and brightness of the cold cathode fluorescent tube 14 are controlled at a constant value by changing the duty in response to a power source voltage.例文帳に追加
バースト信号制御部aは、電源電池の電圧検出機能とバースト信号のデューティ比を制御する機能を備えており、電源電圧に応じてバースト信号のデューティを変化させてインバータ回路12の出力電流及び冷陰極蛍光管14の輝度を一定に制御する。 - 特許庁
When the refrigerating system 20 conducts cooling operation, an opening control means on a heat source side controls an opening of an expansion valve 36 on the heat source side so that the pressure of a refrigerant flowing into expansion valves 51a-51d on the utilization side during cooling operation may be a predetermined pressure reference value or lower.例文帳に追加
冷凍装置20が冷却運転を行う場合は、冷却運転中に利用側膨張弁51a〜51dに流入する冷媒の圧力が所定の圧力基準値以下になるように熱源側膨張弁36の開度を制御する熱源側開度制御手段を設ける。 - 特許庁
To provide a high speed estimation method for a bidirectional reflectance distribution function of an object which is applicable even when a light source is not an ideal remote light source, can calculate a bidirectional reflectance distribution function at very high speed from an acquired measured value, and uses the Wiener estimation method.例文帳に追加
光源が理想的な遠方光源ではない場合に対しても適用可能で、かつ、得られた計測値から非常に高速に双方向反射分布関数を算出することができるウィーナー推定法を用いた物体の双方向反射分布関数の高速推定方法を提供する。 - 特許庁
When vibration input from the vibration source is large input, an electric current value of an electric current carried to an actuator part 30 for moving a movable member 23 for changing the volume of a main liquid chamber 21, is reduced more than when the vibration input from the vibration source is not the large input.例文帳に追加
振動源から入力される振動が大入力である場合には、主液室21の容積を変化させる可動部材23を動かすためのアクチュエータ部30に通電する電流の電流値を、振動源から入力される振動が大入力ではない場合に比べて減少させる。 - 特許庁
In a printing machine, equipped with the plurality of printers which use TA papers to print color images, a sensor for measuring the illuminance value of a light source for fixing detects reduction in the illuminance of the light source for M/Y-fixing of the printer, and a head cleaning abnormality detection means detects head cleaning abnormality of each printer.例文帳に追加
TAペーパーを使用してカラー画像を印画するプリンタを複数装備したプリントマシンにおいて、定着用光源の照度値測定センサがプリンタのM、Y定着用の光源の照度低下を検出し、ヘッドクリーニング異常検出手段が各プリンタのプリンタヘッドクリーニング異常を検出する。 - 特許庁
For each current source within a circuit to be analyzed, an RVC branch circuit in which a false capacitor and a time variation false resistor increased in resistance value with time are serially connected is incorporated in the circuit equation as an equivalent RVC branch circuit converted to an equivalent circuit in which a conductor and the current source are connected in parallel.例文帳に追加
解析対象回路内の各電流源について、擬似キャパシタ及び時間と共に抵抗値が増大する時変擬似抵抗が直列接続されたRVC枝回路を、コンダクタと電流源が並列接続された等価回路に変換した等価RVC枝回路として回路方程式に組み込む。 - 特許庁
In the liquid crystal display device of a field sequential color system, when the color of a light source is changed over and the display state of a liquid crystal display element is changed over by synchronizing it with this, the time-integral value of the luminance of the light source is modulated based on the temperature information or the maximum transmissivity information of the liquid crystal display element.例文帳に追加
フィールドシーケンシャルカラー方式の液晶表示装置おいて、光源の色を切り替え、これに同期させて液晶表示素子の表示状態を切り替える際に、液晶表示素子の温度情報または最大透過率情報に基づいて光源輝度の時間積分値を変調する。 - 特許庁
This method of the pressure resistance test of the AC element applies an AC voltage from an AC power source to the AC element, detects a current supplied from the AC power source to the AC element by a detector, and determines the pressure resistance value of the AC element on the basis of the detected result.例文帳に追加
交流電源から交流素子へ交流電圧を印加し、交流電源から交流素子へ供給される電流を検出器により検出し、その検出結果に基づいて交流素子の耐圧値を判定する交流素子の耐圧テスト方法により上記の課題を解決する。 - 特許庁
The control unit is structured so as to modulate a pulse width of the adjusting signal in accordance with the return signal and a preset luminance value of the light source module, the switch unit is opened and closed in accordance with the adjusting signal, and impresses an AC voltage to the light source module in accordance with the modulated pulse width.例文帳に追加
制御ユニットは、帰還信号と、光源モジュールの事前設定輝度値に従って、調整信号のパルス幅を変調するように構成され、スイッチユニットは調整信号に応じて開閉し、変調されたパルス幅に従って光源モジュールにAC電圧を印加する。 - 特許庁
While defining a document name, a variable name and the pair of values thereof as sharing source variables and defining the pair of the document name and the variable name of a variable to refer to the value of this variable as a sharing destination variable, the context table stores the correspondence of one sharing source variable and plural sharing destination variables as one record.例文帳に追加
共有コンテキストテーブルは、文書名と変数名とその値の組を共有元変数とし、該変数の値を参照する変数の文書名と変数名の組を共有先変数として、一つの共有元変数と複数の共有先変数の対応を一つのレコードとして記憶する。 - 特許庁
A plurality of delay generating units 12 constituted of a CMOS circuit LSI are driven by means of reference clocks REFCK with mutually different phases, and current flowing through a power source is let flow at different timing, so that a current having a large sudden peak value is prevented from flowing through a power source line.例文帳に追加
CMOS回路のLSIで構成された複数の遅延発生部12を互いに異なる位相の基準クロックREFCKで駆動し、電源に流れる電流を異なるタイミングで流れるように構成し、電源ラインに突頭値が大きい電流が流れないようにした。 - 特許庁
A voltage (potential of node RG) to be supplied to the MOS transistor 3 is made to be a value smaller than a power source voltage, thereby delaying a timing of turning on the MOS transistor 3 compared to a timing when the power source voltage Vcc reaches the threshold of the MOS transistor 3.例文帳に追加
充電用のPチャネルMOSトランジスタ3に供給する電圧(ノードRGの電位)を電源電圧より小さい値にすることによって、PチャネルMOSトランジスタ3のオンするタイミングを電源電圧VccがPチャネルMOSトランジスタ3の閾値に達するよりも遅くする。 - 特許庁
A source material of a 1st transparent conductive film 32 is evaporated by an evaporation system in a vacuum chamber where the temperature and the pressure of an atmosphere is set to a proper value, is grown into particles 32a having a proper size before the source material reaches a glass substrate 30 and is deposited on the substrate 30.例文帳に追加
雰囲気の温度および圧力を適切な値に設定した真空室内で,第1の透明導電膜32の原料物質を蒸発装置によって蒸発させ,ガラス基板30に到達するまでに適切な大きさの粒子32aに成長させた後,基板30に付着させる。 - 特許庁
In the vehicular lighting tool 1, the light adjusting lighting control portion 7 changes the oscillation frequency of the supply current to the light source portion 2 and a current value, thereby adjusting a light emitting pattern of the light source portion 2 to be a fine light adjusting pattern at a border between a flicker light area and a fusion light area.例文帳に追加
この車両用灯具1では、調光点灯制御部7が光源部2への供給電流の発振周波数および電流値を変化させることにより、光源部2の発光パターンがフリッカー光領域と融合光領域との境界にある微調光パターンに調整される。 - 特許庁
The image is formed to the recording medium so that the hab at the time of penetration by the fluorescent lamp light source is accommodated within a range of ±15 degrees to the hab of the image non formation part in a range of L* from 20 to a value at the time when the image non formation part is penetrated by the fluorescent lamp light source.例文帳に追加
L*が20から、蛍光灯光源によって画像未形成部が透過された際のL*の値までの範囲では、蛍光灯光源によって透過された際のhabが、画像未形成部のhabに対して±15度の範囲に収まるように、記録媒体に画像形成する。 - 特許庁
The glass member is produced by heating the glass tube with the heat source moving relatively to the glass tube while controlling the inner pressure of the glass tube at the position of the heat source to a predetermined value.例文帳に追加
ガラス管に対して相対的に移動する加熱源により前記ガラス管を加熱する工程を含むガラス部材の製造方法において、前記加熱源の位置におけるガラス管内の圧力を所定の値となるように制御することを特徴とするガラス部材の製造方法、及びそのための装置。 - 特許庁
To provide a control device of an electric power steering device capable of smoothly limiting an assist with a further small sense of incompatibility, without reducing a steeling feeling, by changing a limiting value for limiting the assist in response to source voltage, by imparting the function of limiting the assist when the source voltage reduces.例文帳に追加
電源電圧の低下時にアシストを制限する機能を持たせ、電源電圧に応じてアシスト制限のための制限値を変化させ、操舵フィーリングを低下させることなく、円滑で、より違和感の小さいアシスト制限を行い得る電動パワーステアリング装置の制御装置を提供する。 - 特許庁
When the pachinko balls are shot by rotating a DC motor provided as a shooting source 14 in the normal direction, high-frequency waves are made to overlap multiplexed with respect to a target value for a prescribed period of time while maintaining the average of the target values to shake the shooting source 14.例文帳に追加
発射源14として備えたDCモータを正方向へ回転させることによりパチンコ球が発射される場合に、所定時間中に、目標値の平均を維持しつつ、該目標値に対して高周波重畳を行なうことにより、発射源14を振動させる。 - 特許庁
When all the restriction conditions are satisfied, the total output capacity of the distributed power source 8 is increased and the same calculations are repeated until either one of the restriction conditions is not satisfied to obtain the maximum value of the total output capacity of the distributed power source 8.例文帳に追加
そして、すべての制約条件を満足する場合には、さらに分散型電源8の総出力容量を増加させて、いずれかの制約条件を満足しなくなるまで同様の演算を繰返し、分散型電源8の総出力容量の最大値を求める。 - 特許庁
The audio signal from an audible sound source is processed into a signal of a frequency band at least higher than the audio band through pulse-width modulation and a carrier level and the gain of a modulated signal are set through envelope processing in accordance with a value obtained from the level of the audio signal from the audible sound source.例文帳に追加
可聴音源からのオーディオ信号を少なくとも可聴帯域より高い周波数帯域の信号にパルス幅変調すると共に、可聴音源からのオーディオ信号レベルを包絡線処理した値に応じて搬送波レベル及び変調信号のゲインを設定する。 - 特許庁
Then a low voltage is applied to the ionization chamber 12, by switching a normally-used high-voltage source 30 to a low-voltage power source 32 using a switch mechanism 34 of a power unit 14 and the voltage signal obtained, by converting the output current has its value recorded by a counting arithmetic part 18.例文帳に追加
次に電源ユニット14のスイッチ機構34により通常使用する高電圧電源30から低電圧電源32に切り換えて電離箱12に低電圧を印加し、出力電流が変換された電圧信号を計数演算部18によりその値を記録する。 - 特許庁
The ODD power source control part 18a starts supplying power to the ODD 22 when the detected acceleration speed is equal to or less than a threshold value and it is determined that the AC adapter is connected to the external power source, and an ODD control module 22a ejects a tray of the ODD 22.例文帳に追加
ODD電源制御部18aは、検出した加速度が閾値以下であり、ACアダプタが外部電源に接続していると判別した場合、ODD22に対する電源供給を開始し、ODD制御モジュール22aはODD22のトレイを排出する。 - 特許庁
In addition, when a distance between the RFID tag 2 being a source of transmitting the previous read ID information and the RFID tag 2 being a source of the current read ID information is larger than a predetermined distance reference value, the speed calculation of the railroad vehicle 13 is not carried out.例文帳に追加
また、前回読み取られたID情報の送信元であるRFIDタグ2と今回読み取られたID情報の送信元であるRFIDタグ2との間の距離が所定の距離基準値より大きい場合には、鉄道車両13の速度算出を行わない。 - 特許庁
When a personal computer, etc., readjusts WB, and if a user instructs change of light source setting, a WB coefficient value corresponding to a selected light source is read from the whole WB coefficient values associated with the intermediate RAW data and applied to the intermediate RAW data.例文帳に追加
さらにパーソナルコンピュータ等でWBの再調整を行う際には、ユーザが光源設定の変更を指示すると、選択された光源に対応するWB係数値を中間RAWデータに関連づけされた全WB係数値の中から読み込んで中間RAWデータに適用する。 - 特許庁
The electric power consumption of the display device 1 is suppressed by detecting a peak value of video data, and adjusting a cathode voltage Vc of an organic EL element 11 by a variable voltage source 8 based on the detection data to reduce the potential difference between a power source voltage VDD and the cathode voltage Vc.例文帳に追加
映像データのピーク値を検出し、その検出データに基づいて可変電圧源8による有機EL素子11のカソード電圧Vcを調整して、電源電圧VDDとカソード電圧Vc間の電位差を減少させることにより、表示装置1の消費電力を抑える。 - 特許庁
The high frequency oscillation coil 12, a high frequency oscillation source 13 and RC circuit 11 comprising a capacitor 11a and resistance 11b arranged in parallel are connected in series and a voltage value or a current value between both ends of the RC circuit 11 is detected by a detection part 14.例文帳に追加
この高周波発振コイル12と、高周波発振源13と、並列配設されたコンデンサー11a及び抵抗11bからなるRC回路11とを直列に接続し、RC回路11の両端間の電圧値又は電流値を検出部14で検出する。 - 特許庁
Then the destination peer node estimates the number of response hops from the destination identification value up to the transmission source identification value, and when the number of response hops is smaller than the number of request hops included in the request message, transmits a response message corresponding to the request message to the succeeding peer node registered in the routing table.例文帳に追加
そして、宛先ピアノードが、宛先識別値から送信元識別値までの応答ホップ数を推定し、応答ホップ数が、要求メッセージに含まれる要求ホップ数よりも小さい場合、要求メッセージに対する応答メッセージを、ルーティングテーブルに登録された次ピアノードに送信する。 - 特許庁
A decoupling capacitor determining means 14 determines the capacity value of a decoupling capacitor from an electric charge amount Q needed in every operation cycle of a semiconductor integrated circuit 1 found according to the current flowing to the power terminal of the semiconductor integrated circuit and the voltage permissible variation value ΔV of a source voltage.例文帳に追加
デカップリングコンデンサ決定手段14は、半導体集積回路の電源端子を流れる電流に基づいて求められた半導体集積回路1の動作1周期当りに必要な電荷量Qと、電源電圧の電圧許容変動値ΔVとからデカップリングコンデンサの容量値を決定する。 - 特許庁
In a power-on-reset device generating a signal at turning on of the power supply of a power source unit, an output means 1 for notifying that the value of a supply voltage VDD has reached a value for operating a P-channel MOS transistor Mp, and an N-channel MOS transistor Mn is provided.例文帳に追加
電源装置の電源立ち上がり時に信号を発生するパワーオンリセット装置において、電源電圧VDDの値がPチャネルMOSトランジスタMpとNチャネルMOSトランジスタMnが動作可能となる値になったことを知らせる出力手段1を有する。 - 特許庁
With the operation of an XY table 6 where an X-ray source 1 is mounted, by using only a direction where the projection of a metal wire near the rotary shaft of a specimen 5 moves and the measurement value of a travel amount, approach to ideal X-ray focus coordinates is made gradually by calculation and at the same time an optimum value is obtained.例文帳に追加
X線源1を搭載したXYテーブル6の操作にともなって、被検査体5の回転軸近傍の金属線の投影が移動する方向と移動量の計測値のみを用いて、演算により徐々に理想的なX線焦点座標へ寄りつつ最適値を求める。 - 特許庁
The pull-down detection circuit detects a total time DT when 24-frame discrimination signals C outputted from a 24-frame discrimination circuit 10 are logical "1" for thirty seconds in the past (discrimination of 24-frame source), and a sensitivity reference value setting circuit 20 determines a sensitivity reference value REF of a comparator 13 in response to the time DT.例文帳に追加
24コマ判定回路10から出力する24コマ判定信号Cが過去30秒間に「1」(24コマソース判定)であった合計時間DTを検出し、その時間DTに応じて感度基準値設定回路20により比較器13の感度基準値REFを決める。 - 特許庁
The driving voltage waveform is applied by connecting with the driving element while a plurality of power sources with different voltage values with each other are switched, and at the target waveform part of the driving voltage part, the voltage is applied under a condition that the voltage value of the power source is precisely controlled to the target voltage value.例文帳に追加
そして、互いに電圧値が異なる複数の電源を切り替えながら駆動素子に接続することで駆動電圧波形を印加すると共に、駆動電圧波形の目標波形部分では、電源の電圧値を目標の電圧値に対して精度良く制御した状態で電圧を印加する。 - 特許庁
The second commutation switch turn-off controlling switch element Q4 is turned on by a flyback voltage application circuit 26 when a flyback voltage of the transformer T is raised to a value not lower than a prescribed value, and quickly discharges the charge of the capacity between the gate and the source of the commutation switch element Q3.例文帳に追加
第2の転流スイッチターンオフ制御用スイッチ素子Q4は、フライバック電圧印加回路26によって、トランスTのフライバック電圧が所定値以上に上昇したときにオンして、転流スイッチ素子Q3のゲート・ソース間容量の電荷を速やかに放電させる。 - 特許庁
A comparison/determination part 107 receives a power supply current value of a port corresponding to a faulty disk 102 from a current monitoring part 106, and recognizes removal of the faulty disk 102 and insertion of a new disk 102 by determining the power source current value.例文帳に追加
比較・判断部107は、異常が発生したディスク102に対応するポートの電源電流値を電流監視部106から採取し、その電源電流値を判定することにより、異常が発生したディスク102の抜去及び新たなディスク102の挿入を認識する。 - 特許庁
A specific portion 72 detects a failure of the other terminal device being a notifying source of a signal periodically received when the quality of signal periodically received is deteriorated more than a second threshold value, however, the strength of the signal periodically received is larger than a first threshold value.例文帳に追加
特定部72は、周期的に受信した信号の強度が第1のしきい値よりも大きいにもかかわらず、当該周期的に受信した信号の品質が第2のしきい値よりも悪化している場合に、周期的に受信した信号の報知元になる他の端末装置の故障を検出する。 - 特許庁
Specifically, it is decided, based on the light emission information of the auxiliary light source, whether an image-quality adjustment should be executed or not, and when it is decided that the image-quality adjustment should be executed, the image data adjustment is so performed as to reduce the highest brightness value that is a possible maximum value of the brightness represented by the image data.例文帳に追加
具体的には、補助光源の発光情報に基づいて画質調整処理を実行するか否かの判定を行い、実行すると判定した場合には、画像データで表される輝度値が取りうる最大値である最高輝度値を小さくするように画像データを調整する。 - 特許庁
When the human body approaches the detection electrode 2, an electrostatic capacity detection circuit detects a change of ground capacity of the detection electrode 2, and a lighting control circuit turns on or turns off the light source 3 when a detection value thereof exceeds a prescribed threshold value successively for a prescribed time.例文帳に追加
人体が検知電極2に接近すると、検知電極2の対接地容量の変化を静電容量検知回路が検出し、その検出値が所定のしきい値を一定時間継続して超えたときに照明点灯制御回路が光源3を点灯又は消灯する。 - 特許庁
A power source microcomputer 4 is able to communicate with the internal memory 2 of a battery pack 1 through an I2C communication bus, and reads rated discharging current data characteristic of the battery pack 1 out of the internal memory 2 and saves them as a 1st specific value (current value for operating a power consumption reducing function) therein.例文帳に追加
電源マイコン4は、電池パック1の内蔵メモリ2とI^2C通信バスにより通信が可能であり、内蔵メモリ2に保存されている電池パック1に固有の定格放電電流データをリードし、第1の所定値(消費電力低減機能を作動させる電流値)として内部に保存する。 - 特許庁
When the same set is not registered in a storage position of the encrypted value a' of a first table 143 and a storage position of the encrypted value b' of a second table 144, the set of the user ID and the ticket No. included in the issue request is registered, and the ticket is transmitted to a request source.例文帳に追加
第1テーブル143の暗号化値a’の記憶位置と第2テーブル144の暗号化値b’の記憶位置に、同一の組が登録されていなければ、発行要求に含まれるユーザID及びチケットNo.の組を登録し、チケットを要求元に送信する。 - 特許庁
The initialization of a random number circuit is carried out until the timer interruption is set after the start of closing a power source to a pachinko game machine 1 while in the initialization, the value based on the ID number proper to the microcomputer for game control is set as an initial value of random numbers (S154b).例文帳に追加
パチンコ遊技機1への電源投入が開始されてからタイマ割込設定を行なうまでに、乱数回路の初期設定を行なうとともに、初期設定において、遊技制御用マイクロコンピュータ固有のIDナンバに基づく値を乱数の初期値として設定する(S154b)。 - 特許庁
The capacity added to the capacity component is set to the capacity for not switching on the commutation side synchronous rectifier 7 by preventing a voltage value to be impressed between the gate and the source of the synchronous rectifier 7, based on the resonance operation from exceeding a preset threshold value.例文帳に追加
その付与される容量成分の大きさは、共振動作に基づいて転流側同期整流器7のゲート−ソース間に印加される電圧が設定のしきい値電圧を越えない電圧値となるようにして転流側同期整流器7をスイッチオンさせないための大きさに設定する。 - 特許庁
A frequency correction value calculator 215 calculates a frequency correction value to the packet signal during a demodulating process by using information regarding a frequency offset of a series of the packet signals transmitted from the transmission source specified by the extracted ID signal before.例文帳に追加
周波数補正値算出部215では、抽出されたID信号により特定される送信源から以前に伝送された一連のパケット信号の周波数オフセットに関する情報を用いて、復調処理中のパケット信号に対する周波数補正値が算出される。 - 特許庁
When the output power of a power source reaches a first threshold when the first battery pack 125 requires charging in a standard charging mode, the first charger is operated at a set value at which power consumption becomes smaller than a set value required by the first battery pack.例文帳に追加
第1の充電器は、第1の電池パック125が標準充電モードでの充電を要求するときに電力源の出力電力が第1の閾値に到達したときには第1の電池パックが要求する設定値よりも消費電力が小さくなる設定値で動作する。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|