| 例文 |
voltage controllerの部分一致の例文一覧と使い方
該当件数 : 2590件
A second current controller receives a current from the output node, in response to a second logic level of a second signal and buffers an input voltage, to provide an output on the output node in response to a first logic level of the second signal.例文帳に追加
第2電流制御部は、第2信号の第2論理レベルに応答して出力ノードから電流を受け、第2信号の第1論理レベルに応答して入力電圧をバッファリングして出力ノードに出力する。 - 特許庁
To provide a motor controller and its control method wherein even if a voltage command is output at an arbitrary timing, extra PWM pulses are not generated, and even when a carrier frequency is low, a high current response is ensured.例文帳に追加
任意のタイミングで電圧指令出力を行っても、余分なPWMパルスが発生せず、キャリア周波数が低い場合でも電流応答を高くしたモータ制御装置とその制御方法を提供する。 - 特許庁
To accurately detect a voltage drop of a battery before the battery becomes completely exhausted and urge a user to replace the battery, so as not to cause a battery backup operation for a programmable controller memory to be interrupted due to battery exhaustion.例文帳に追加
電池が完全に消耗する前に電池の電圧低下を的確に検出して、ユーザに電池の交換を促し、プログラマブルコントローラ用メモリのバッテリバックアップ動作が電池の消耗によって途切れないようにする。 - 特許庁
To provide a low-cost voltage converter circuit, having a relatively simple structure using only a capacitor and a diode, without need for a special power semiconductor controller or without using an expensive wound transformer.例文帳に追加
高価な巻線変圧器を用いることなくコストが安価であり、しかも特別な電力用半導体制御部を必要とせず、キャパシタとダイオードのみを用いた比較的構造の簡単な電圧変換回路を提供する。 - 特許庁
The controller circuit latches the power conversion apparatus to off state, in response to the detection of loss of adjustment of the power conversion apparatus output parameter, when power conversion apparatus input voltage exceeds a threshold level.例文帳に追加
コントローラ回路は、電力変換装置入力電圧が閾値レベルを超えている場合、電力変換装置出力パラメータの調整が失われたことの検出に応答して、電力変換装置をオフ状態にラッチする。 - 特許庁
The current command converting part 13a of the controller 13 converts the inputted torque command signal of the motor 11 into a motor current required to obtain its torque and outputs it to a voltage-computing part 13b.例文帳に追加
制御装置13の電流指令変換部13aは、入力されるモータ11のトルク指令信号を、そのトルクを得るために必要とされるモータ電流に変換して電圧演算部13bに出力する。 - 特許庁
This power circuit is composed of a master slave type DC-DC converter 3, a controller 4, and current/voltage sensors 5 and 6, and this is provided together with an inverter between an electric motor 1 and a battery 7.例文帳に追加
本発明の電源回路は、マスタ−スレーブ型DC−DCコンバータ3、コントローラ4および電流/電圧センサ5、6により構成されており、電動発電機1とバッテリ7との間にインバータ2と共に設けられている。 - 特許庁
The measured value of the operating condition in the distributed power source 3 (voltage source) is compared with the target value established by the controller 4, and the difference is calculated to vary the operating condition (for example, active power, reactive power) of a current source 1.例文帳に追加
分散型電源(電圧源)3の運転状態の実測値と、制御装置4で設定した目標値とを比較し、差分を計算し、電流源1の運転状態(例:有効電力、無効電力)を変化させる。 - 特許庁
When a voltage sensor 52 is abnormal and when a prescribed fuel saving running condition is met, or the like, a controller 40 executes upper arm running to make a switching element Q1 of the boost converter 10 keep an on-state continuously.例文帳に追加
制御装置40は、電圧センサ52の異常時や所定の省燃費走行条件の成立時等に、昇圧コンバータ10のスイッチング素子Q1を継続的にオン状態とする上アームオン走行を実行する。 - 特許庁
To provide a motor controller in which a voltage drop or erroneous operation hardly takes place at the time of starting backup even when an external battery (lithium battery) stored for a long term is used as backup for the operation power supply of an encoder.例文帳に追加
長期間保存された外部電池(リチウム電池)をエンコーダの動作電源のバックアップとして使用した場合でも、バックアップ開始時の電圧低下や誤動作を起し難いモータ制御装置を提供する。 - 特許庁
A main controller 17 detects an input power factor of the PWM cyclo-converter 3 with the phase difference signal 16 and the lead or the lag of the input voltage signal 8 against the input signal current which are preliminary known.例文帳に追加
メインコントローラ17は位相差信号16と、予めわかっている入力電圧信号8の入力電流信号に対する進み/遅れからPWMサイクロコンバータ3の入力力率を検出する。 - 特許庁
To provide a controller of a vibration type actuator capable of controlling the frequency of applied voltage highly accurately following changes of friction force, environmental change, and changes of frequency response characteristic due to individual difference.例文帳に追加
摩擦力の変化、環境変動、個体差による周波数応答特性の変化に追随して、印加電圧の周波数を高精度に制御することができる振動型アクチュエータの制御装置を提供する。 - 特許庁
To provide an engine controller and a screening method wherein a voltage switching command signal for screening is positively and reliably realized by a simple system without requiring an exclusive input terminal.例文帳に追加
スクリーニングのための電圧切換え指令信号を専用の入力端子を必要とせず、簡易な方式により確実な信頼性を伴って実現することができるエンジン制御装置及びスクリーニング方法を提供する。 - 特許庁
This controller obtains a three-phase voltage commands vu^*[V], vv^*[V], and vw^*[V], based on motor angular frequency ω[rad/s], a torque command T^*[N×m], and three-phase currents iu[A], iv[A], and iw[A].例文帳に追加
本制御装置では、モーター角周波数ω[rad/s]、トルク指令値T^*[N・m]および3相電流iu[A]、iv[A]、iw[A]に基づいて、3相電圧指令値vu^*[V]、vv^*[V]、vw^*[V]を求める。 - 特許庁
To provide a power supply controller and a load power supply system capable of setting the priority of the power supply to a plurality of load apparatuses by a relative simple configuration, and suitably using even when an output voltage of a generator is lower than an operation voltage of the load apparatus.例文帳に追加
比較的簡単な構成で複数の負荷装置への電力供給の優先順位を設定することができ、また、発電装置の出力電圧が負荷装置の作動電圧より低い場合であっても好適に使用することができる電力供給制御装置および負荷電力供給システムを提供する。 - 特許庁
A digital controller 11 for repairing the chip digitally control the application of heating current pulse from a heating current pulse adjusting device 10 and reverse charge voltage from a reverse charge voltage adjusting device 9 to flash the electron gun chip 3 under heating and repair the shape.例文帳に追加
更に、電子銃チップ3に対する加熱電流パルス調整装置10からの加熱電流パルスおよび逆電荷電圧調整装置9からの逆電荷電圧の付与をチップ修復ディジタル制御装置11でディジタル制御することにより、電子銃チップ3に対して加熱フラッシングおよび形状修復が行われる。 - 特許庁
An error amplifier 31 determining an error between the output voltage of the outputting part 26 and a reference voltage to output an error signal, a triangular wave generating part 33, and a switching regulator controller 28 having a comparator 32 are also included to obtain switching power and the stable circuit 27 is disposed between the inputting part 25 and the error amplifier 31.例文帳に追加
更に、スイッチング電源を得るために、出力部26の出力電圧と基準電圧との誤差を求めて誤差信号を出力する誤差増幅器31と、三角波発生部33と、コンパレータ32を有するスイッチングレギュレータ・コントローラ28を備え、安定回路27を入力部25と誤差増幅器31との間に設けた。 - 特許庁
The electronic equipment device 1 includes: a DDR memory 2; a control IC 3 for controlling the writing/reading of data to the DDR memory 2; and a voltage output circuit 4 for setting a reference Vref-ddr in the DDR memory 2 and a reference voltage Vref-ic in the controller IC 3.例文帳に追加
電子機器装置1は、DDRメモリ2と、DDRメモリ2に対するデータの書込み/読出しを制御するコントロールIC3と、DDRメモリ2における基準電圧Vref−ddr及びコントロールIC3における基準電圧Vref−icを設定する電圧出力回路4とを備える。 - 特許庁
When an inverter is restarted after stoppage, the controller performs an operation for starting switching of the inverter after the DC voltage Vdc of the inverter has dropped down to the working voltage during operation, thus restarting the operation stably without stopping the system.例文帳に追加
前記課題を解決するため、本発明に係る制御装置は、インバータの動作を停止後、再起動する際において、インバータの直流電圧Vdcが運転時の動作電圧まで低下した後に、インバータのスイッチングを開始する操作を行うことで、システムを停止させることなく安定に再起動するようにした。 - 特許庁
To provide a power supply circuit for LED (light-emitting diode) lighting with a high power factor at use as a commercial alternating-current power source in an inverter system capable of controlling light by a general light controller varying a power supply voltage or an average power supply voltage, and an LED electric bulb mounted with the power supply circuit for the LED lighting.例文帳に追加
電源電圧又は平均電源電圧を可変させる一般的な調光器で調光可能なインバータ方式で、商用交流電源で使用する際に力率が高いLED(発光ダイオード)点灯用電源回路及び該LED点灯用電源回路を搭載したLED電球を提供する。 - 特許庁
A controller 150 acquires various correction data in a characteristic parameter acquiring operation, based on a plurality of voltage values at one end of a data line Ld detected with different timing after voltage for detection is applied to each pixel PIX via a data driver 140 and luminance data detected about each pixel PIX.例文帳に追加
コントローラ150は、特性パラメータ取得動作において、データドライバ140を介して各画素PIXに検出用電圧を印加した後の異なるタイミングで検出される、データ線Ldの一端の複数の電圧値、及び、各画素PIXについて検出された輝度データに基づいて、各種の補正データを取得する。 - 特許庁
The ink liquid feed controller includes: a means for measuring a voltage between two electrodes provided in a sub ink tank; a control means for stopping the liquid feed of the ink to the sub ink tank when the voltage is smaller than a first predetermined value; and a means for setting the first predetermined value based on an electric conductivity of the ink.例文帳に追加
サブインクタンク内に設けられた2本の電極の間の電圧を測定する測定手段と、前記電圧が第1の所定の値より小さい場合に、前記サブインクタンクへのインクの送液を停止させる制御手段と、前記第1の所定の値を、前記インクの電気伝導度に基づいて設定する設定手段と、を有する。 - 特許庁
In the LED driving circuit 1, a feedback controller 50 controls automatically a control voltage Vx to be applied to an LED array 100 so that a predetermined voltage Vs is applied to the LED array 100, based on voltages Vr at both ends of a detection resistance 10 connected in series with the LED array 100.例文帳に追加
LED駆動回路1では、フィードバック制御部50により、LEDアレイ100に直列接続された検出用抵抗10の両端電圧Vrをもとに、LEDアレイ100に所定の設定電圧Vsが印加されるよう、LEDアレイ100に印加すべき制御電圧Vxが自動的に制御される。 - 特許庁
Similarly, when a second detection signal 400B (voltage value VB) is inputted to the measurement controller 30 from the rotation sensor 100, correspondence relationship on the second detection signal 400B of the rotation sensor 100 is selected from the storage table 36, and rotation angles θB1 and θB2 corresponding to the present detection voltage value VB are read.例文帳に追加
同様に、計測用コントローラ30に、回転センサ100から第2の検出信号400B(電圧値VB)が入力されると、記憶テーブル36から、回転センサ100の第2の検出信号400Bについての対応関係が選択され、現在の検出電圧値VBに対応する回転角度θB1、θB2が読み出される。 - 特許庁
This load controller includes: two power conversion parts which convert DC voltage into AC voltage to be applied to the two rotation type inductive loads with the same specification; a current detection part which detects DC current to be supplied to the power conversion parts; and a control part which controls the power conversion parts.例文帳に追加
負荷制御装置は、直流電圧を交流電圧に変換して、同じ諸元の2つの回転型誘導性負荷に印加する2つの電力変換部と、電力変換部に供給される直流電流を検出する電流検出部と、電力変換部を制御する制御部とを備える。 - 特許庁
The controller 25 switches over the gain factor of a servo- gain amplifier provided to a thread servo circuit 18 and the filtering factor of a servo phase compensation filter so that the voltage level of the control voltage applied to a thread motor 26 becomes higher as the position of the optical pickup 12 on an optical disk 1 moves toward the outside.例文帳に追加
コントローラ25は、光ピックアップ12の光ディスク1上における位置が外側になるに従ってスレッドモータ26に印加される制御電圧の電圧レベルが高くなるように、スレッドサーボ回路18に備えられているサーボゲインアンプのゲイン係数とサーボ位相補償フィルタのフィルタ係数とを切り換える。 - 特許庁
The vehicle is equipped with a battery B1 which can be charged with electricity from outside a vehicle, a DC/DC converter 33 which steps down the voltage of the battery B1 prior to output, a battery B3 which is charged with output voltage from the DC/DC converter 33 and besides supplies an auxiliary load 35 with power, and a controller 30.例文帳に追加
車両は、車両外部から充電が可能なバッテリB1と、バッテリB1の電圧を降圧して出力するDC/DCコンバータ33と、DC/DCコンバータ33の出力電圧によって充電され、かつ補機負荷35に電力を供給するバッテリB3と、制御装置30とを備える。 - 特許庁
When control is performed to reduce the driving output of the driving motor 5a, the system controller 6 lowers the response of driving control for the driving motor 5a with referring to the reduction amount, the detection voltage of a system power source voltage sensor 7, the detection temperature of a battery temperature sensor 4, and the temperature characteristic of the battery 3, etc.例文帳に追加
システム制御器6は、駆動モータ5aの駆動出力を低下させる制御を行う場合に、その低下量、システム電源電圧センサ7の検出電圧、バッテリ温度センサ4の検出温度、バッテリ3の温度特性などを参照して、駆動モータ5aの駆動制御の応答性を低下させるようになっている。 - 特許庁
The display device comprises: a variable electric power supply part which supplies electric power to light sources; a switching part which is connected in series with the light sources; and a controller which controls the variable electrical power supply so that voltage across both ends of the switching part is held constant according to variation in voltage across both ends of the light sources.例文帳に追加
光源に電源を供給する可変電源供給部と;前記光源に直列で連結されているスイッチング部と;前記光源両端の電圧変化に対応して前記スイッチング部両端の電圧が一定に維持されるように前記可変電源供給部を制御する制御部とを含む。 - 特許庁
Then, the main controller 102 adjusts the voltage value of the transfer bias which is applied to the secondary transfer roll 8 by the transfer device control section 118, according to an adjusting operation manually performed based upon the calibration pattern PT, and sets the adjusted voltage value, as the set value of the transfer bias, for the transfer device control section 118.例文帳に追加
次いで、メインコントローラ102が、転写装置コントロール部118により二次転写ロール8に印加される転写バイアスの電圧値を、キャリブレーションパターンPTに基づいてマニュアルで行われる調整操作に応じて調整し、この調整後の電圧値を転写装置コントロール部118に転写バイアスの設定値として設定する。 - 特許庁
In an AC electric motor controller provided with an integrated current control system, the integration term of the integrated current control system is converged into zero to stop the integrated current control, when the impressed voltage to the electric motor is put into a saturated state; then the control is changed over to proportional voltage control using a proportional term.例文帳に追加
積分電流制御系を備えた交流電動機の制御装置において、電動機への印加電圧が飽和状態となった場合には、積分電流制御系の積分項を零に収束させて積分電流制御を中止するとともに、比例項を用いた比例電圧制御に切り換えることを特徴とする。 - 特許庁
The system controller 106 makes the auxiliary load controllers 132, 136, and 160 reduce power consumption of the auxiliary loads 130, 134, and 158 from the auxiliary energy sources 110, 126, and 164 and provide a boosted voltage to the DC link 114 by boosting the voltage provided by the auxiliary energy sources 110, 126, and 164.例文帳に追加
システム・コントローラ106は、補助負荷コントローラ132、136、160に、補助エネルギー源110、126、164からの補助負荷130、134、158の消費電力を減らし、補助エネルギー源110、126、164から供給される電圧を昇圧させて昇圧電圧をDCリンク114に供給する。 - 特許庁
The controller 1 determines whether the output value of the A/D converter 9 is higher than, lower than, or equal to a voltage value K, and determines whether output from the IC2 for PWM conversion is present or not, and individually detects the short-circuiting and disconnection of wiring (b) for connecting the solenoid proportional valve 4 to the voltage converter 5.例文帳に追加
コントローラ1は、A/D変換部9の出力値が電圧値Kよりも高いか低いか同じであるかの判定とPWM変換用IC2からの出力があるか否かの判定を行い、電磁比例弁4と電圧変換部5とを接続する配線bの短絡及び断線を個別に検出する。 - 特許庁
When charging is started and the battery voltage detecting section 22 detects that the battery voltage VCC2 becomes a predetermined potential, a control signal is applied to a charge controller from a charge control output section 24 through a terminal OC1 after a given period of time set by an insensitive time setting section 23.例文帳に追加
充電が開始され電池電圧Vcc2が所定電位になったことを、電池電圧検出部22が検出すると、不感応時間設定部23で設定された所定時間経過した後に、充電制御出力部24から、端子OC1を介して、充電制御手段(図示せず)に制御信号が印加される。 - 特許庁
In the transmission power controller, where a high frequency power amplifier circuit 111 has a semiconductor amplifier element adopting a common source connection, controlling the gate voltage and/or the drain voltage of the semiconductor amplifier element linearly changes the gain of the high-frequency power amplifier circuit 111 for controlling transmission power.例文帳に追加
高周波電力増幅回路111がソース接地された半導体増幅素子を有する送信電力制御装置で、半導体増幅素子のゲート電圧および/またはドレイン電圧を制御して、高周波電力増幅回路111の利得を線形的に変化させ、送信電力を制御する。 - 特許庁
When an input voltage V2 to the DC/DC converter 25 lowers and the DC/DC converter 25 returns back to an normal output mode after being driven in an output limit mode, a controller 30 drives the DC/DC converter 25 to deliver an output voltage higher than that in the normal output mode.例文帳に追加
制御装置30は、DC/DCコンバータ25への入力電圧V2が低下し、DC/DCコンバータ25が出力制限モードで駆動された後、通常出力モードに戻ると、通常出力モードにおける出力電圧よりも高い出力電圧を出力するようにDC/DCコンバータ25を駆動する。 - 特許庁
A fixing heater controller possesses a voltage measuring means to measure the voltage of the AC power source, a temperature measuring means to measure the temperature of a fixing roller heated by a fixing heater and an abnormality detecting means to detect the abnormality by monitoring the change of temperature measured by the temperature measuring means.例文帳に追加
本発明の定着ヒータ制御装置は、AC電源の電圧を測定する電圧測定手段と、定着ヒータによって加熱された定着ローラの温度を測定する温度測定手段と、温度測定手段によって測定される温度の変化を監視して異常を検出する異常検出手段とを有している。 - 特許庁
Even if the set voltages of the pair of DC power-receiving terminals 3a and 3b are switched, the rectification controller 6 controls so that a first reference voltage Vcc is surely supplied to a power supply terminal 4p of the control circuit 4, and a second reference voltage Vss is surely supplied to a ground terminal 4g of the control circuit 4.例文帳に追加
一対の直流受電端子3a,3bの設定電圧が入れ替わっても、制御回路部4の電源端子4pには、必ず第1の基準電圧Vccが供給されて、制御回路部4の接地端子4gには、必ず第2の基準電圧Vssが供給されるように整流制御部6で制御する。 - 特許庁
Also, at the time of switchover processing to the normal mode, after power voltage is stabilized following the initialization of the CPU 1 in the process of power voltage rising, on confirming clock synchronization for synchronizing each circuit provided in its own-unit, the power saving controller decides the own-unit is in an operable condition.例文帳に追加
通常モードに切り替える処理の際にも、省電力制御部は、電源電圧の立ち上がりの過程において、CPU1を初期化して電源電圧が安定後、自装置が有する各回路の同期を取るためのクロックが同期していることを確認すると、自装置が動作可能な状態であると判断する。 - 特許庁
And a charging device of the secondary battery which comprises a switch, a voltage measuring apparatus for measuring battery voltages, and a controller for computing variations of measured voltages, and for sending power off signals to the switch when a drop of 0.0005 to 0.0015 V/10 s takes place, from the maximum value of the voltage variations.例文帳に追加
及び、開閉器と、電池電圧を測定する電圧測定器と、測定された電圧の変化量を算出し、その電圧変化量の最大値より0.0005〜0.0015V/10秒の低下が生じた時に開閉器に電源切断信号を送る制御器とからなる二次電池の充電装置。 - 特許庁
The controller 70, if a value of a signal FUEL indicating a remaining fuel level in a fuel tank 40 drops below a predetermined threshold value R0, controls the inveters 20, 30 so as to change a voltage level of the AC voltage Vac, in order to annunciate that the remaining fuel level is low to a user outside a vehicle.例文帳に追加
ここで、制御装置70は、燃料タンク40内の燃料残量を示す信号FUELの値が所定のしきい値R0を下回ると、燃料残量が少ないことを車両外部のユーザに報知するため、交流電圧Vacの電圧レベルを変化させるようにインバータ20,30を制御する。 - 特許庁
A controller 4 adjusts the voltage value supplied by the voltage supply means discretely by the each sub-pixel according to the video information, such as display mode selection, in a user operation section 2, and performs display control of the liquid crystal display panel 8 by correcting the gray scale characteristics of the unit pixels changed by the adjustment processing.例文帳に追加
コントローラ4は、ユーザ操作部2での表示モード選択など映像情報に応じて、電圧供給手段で供給される電圧値を副画素個別に調整し且つその調整処理によって変更された単位画素の階調特性を補正して、液晶表示パネル8の表示制御を行う。 - 特許庁
A forklift, which is equipped with a vehicle controller 26 that executes the limitation of the operation of a forklift in case that the voltage of the lead acid battery mounted on the forklift as a drive source falls short of a threshold voltage, is made a fuel cell type forklift by being mounted with a fuel cell unit FU in replacement of the lead acid battery.例文帳に追加
駆動源としてフォークリフトに搭載された鉛バッテリの電圧が閾値電圧に達していない場合に、フォークリフトの動作の制限を実行する車両コントローラ26を装備したフォークリフトにおいて、鉛バッテリと置き換えて燃料電池ユニットFUを搭載することで燃料電池式のフォークリフトとされている。 - 特許庁
A controller 60 operates as follows: when the motor generator MG1 is not used and the motor generator MG2 is used, it turns on the switch 40 in parallel with the voltage converting operation of a booster unit 10; and thus it causes the inverter 20 to perform voltage converting operation using the stator coils of the motor generator MG1 as a reactor.例文帳に追加
制御装置60は、モータジェネレータMG1を使用せず、モータジェネレータMG2を使用する場合に、昇圧ユニット10の電圧変換動作と並行してスイッチ40を接続状態にしインバータ20にモータジェネレータMG1のステータコイルをリアクトルとして使用した電圧変換動作を行なわせる。 - 特許庁
When a first detection signal 400A (voltage value VA) is inputted to a measurement controller 30 from the rotation sensor 100, correspondence relationship on the first detection signal 400A of the rotation sensor 100 is selected from a storage table 36, and rotation angles θA1 and θA2 corresponding to the present detection voltage value VA are read.例文帳に追加
計測用コントローラ30に、回転センサ100から第1の検出信号400A(電圧値VA)が入力されると、記憶テーブル36から、回転センサ100の第1の検出信号400Aについての対応関係が選択され、現在の検出電圧値VAに対応する回転角度θA1、θA2が読み出される。 - 特許庁
The micro controller 20 adjusts frequency of an AC power that is supplied to a primary coil 18 from a DC/AC converter 16 so that a detection value of voltage fluctuation agrees with a value of voltage fluctuation at the time when the power transmission efficiency from the non-contact power transmission device 10 to the power receiving device 50 becomes maximum.例文帳に追加
そして、マイクロコントローラ20は、無接点電力伝送装置10から受電装置50への送電効率が最大となるときの電圧変動の値に電圧変動の検出値が一致するように、DC/ACコンバータ16から一次コイル18へ供給される交流電力の周波数を調整する。 - 特許庁
The X-ray apparatus starts outputting a pulsed tube voltage V_T by a pulse-voltage controller when a command is input to start fluoroscopy at the time t_1, and at the same time a filament current I_F is increased in a filament heater to heat a filament 12 for the purpose of seeing through a device under test by means of a generated X ray.例文帳に追加
本発明に係るX線装置は、時間t_1において透視開始の指令が入力されると、管電圧制御部がパルス状管電圧V_Tを出力し始めるとともに、フィラメント加熱部がフィラメント電流I_Fを増大させてフィラメント12を加熱し、発生させたX線によって被検体の透視を行う。 - 特許庁
In its process, when the voltage of the charging power supply 2 becomes lower than a predetermined range, the controller 13 determines that the voltage reaches the rating of the charging power supply 2, and charges the battery 12 while controlling a switch part 18 so as not to exceed a supply power capacity of the charging power supply 2.例文帳に追加
その過程で、充電用電源2の電圧が所定の範囲を越えて低くなった場合、制御装置13は、充電用電源2の定格に達したと判定して、当該充電用電源2の供給電力能力を越えないようにスイッチ部18を制御しつつ電池12の充電を実行する。 - 特許庁
This controller 1 for a secondary battery is provided with a voltage measuring part 4 for measuring the terminal voltage of the secondary battery 40 and a control part 5 for setting the upper limit value of a discharge power which can be output by the secondary battery 40 within a set time, and for outputting the set upper limit value to a vehicle ECU 20.例文帳に追加
二次電池40の端子電圧を測定する電圧測定部4と、設定時間内に二次電池40が出力可能な放電電力の上限値を設定し、車両ECU20に、設定した上限値を出力する制御部5とを備えた二次電池用の制御装置1を用いる。 - 特許庁
To provide a voltage controller of a generator for vehicle in which fuel consumption can be enhanced through voltage switching control using a navigation system, and deterioration of a battery and the starting performance of an engine incident to lowering of residual capacity of the battery when a vehicle is left as it is for a long time after stopping engine can be prevented.例文帳に追加
ナビゲーションシステムを用いて、電圧切換制御による燃費の向上を達成し、かつエンジン停止後の車両の長時間放置によるバッテリ残存容量の低下に伴うエンジンの始動性悪化及びバッテリの劣化を防止することができる車両用発電機の電圧制御装置を提供する。 - 特許庁
| 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|