| 意味 | 例文 |
constant- currentの部分一致の例文一覧と使い方
該当件数 : 4593件
Under this drive method, each of the element having different emitting area can be driven in an optimal condition by adjusting the capacitance of the capacitor or the like and the time for switching to the constant-current driving.例文帳に追加
この駆動方法では、コンデンサ等の容量と定電流駆動に切り替える時間とを調整することにより、発光面積の異なる素子の各々に最適な条件で駆動することができる。 - 特許庁
The differential amplification circuit is composed of: N type transistors Q1 and Q2 which are input means, P type transistors Q3 and Q4 composing active load, a constant current source I0, and voltage differential detection means DA.例文帳に追加
入力手段となるN型トランジスタQ1およびQ2、能動負荷を構成するP型トランジスタQ3およびQ4、定電流源I0、電圧差検出手段DAから構成されている。 - 特許庁
By turning one of the switch circuits from ON to OFF, a constant current flowing through the input side transistors is not distributed to the input side transistors in which switch circuits are turned OFF.例文帳に追加
このとき、スイッチの1つをONからOFFにすることで、複数の入力側トランジスタに分流されていた定電流がスイッチ回路がOFFにされた入力側トランジスタに分流されなくなる。 - 特許庁
To increase heat capacity, and at the same time, make heat-dissipation time constant small with regard to a battery connection tool used for structuring a secondary battery unit which makes high current charge and discharge possible through connection of a secondary battery.例文帳に追加
二次電池を接続して大電流の充放電が可能な二次電池ユニットを構成するのに用いる電池接続具において、熱容量を増大すると同時に放熱時定数を小さくする。 - 特許庁
This uniform charge system charges the lead-acid battery until reaching a set voltage (V) of the lead battery at a constant current, and measures and stores a charge time (T1(h)) from the start of charge up to the reaching to the set voltage (V).例文帳に追加
一定の電流のもとで鉛蓄電池が設定電圧(V)に達するまで充電し、充電開始から設定電圧(V)に達するまでの充電時間(T1(h))を測定して記憶する。 - 特許庁
In this ripple filter circuit, a connecting point between a resistor 4 and a capacitor 5 is connected to a base of an NPN transistor(TR) 6, and an emitter of the NPN TR 6 is connected to a constant current source 8 via a resistor 7.例文帳に追加
リップルフィルタ回路は、抵抗4とコンデンサ5の接続点とNPNトランジスタ6のベースを接続し、NPNトランジスタ6のエミッタから抵抗7を介して定電流源8に接続する。 - 特許庁
To provide a constant current power supply device wherein transient phenomena such as an overshoot and distortion by response delay are drastically reduced, in an intermittent load using a three-terminal regulator.例文帳に追加
三端子レギュレータを用いた断続する負荷において、応答遅れによる歪およびオーバーシュートのような過度現象を大幅に軽減した定電流電源装置を提供することを目的とする。 - 特許庁
To perform uniform melting treatment at an optional position in the width direction of a cast slab by adjusting distribution of alternating current magnetic fields thereby making an incident angle of a plasma arc on the surface of the cast slab always constant.例文帳に追加
交流磁場の分布を調整することによってプラズマアークの鋳鋼片表面への入射角を常に一定にし、鋳鋼片の幅方向の任意の位置において均一な溶融処理を行う。 - 特許庁
To shorten the time from when a fixing device and an image forming apparatus are powered on or a recovery from a power-saving mode to image output by improving the accuracy of constant-current control in temperature control over a fixing unit.例文帳に追加
定着器の温度制御における定電流制御の精度を向上させることにより、装置の電源投入または省電力モード復帰から画像出力までの時間を短縮する。 - 特許庁
In the case that positive static electricity infiltrates it and an input voltage Vin is increased exceeding a prescribed threshold voltage, a constant voltage circuit 41 is turned into a current flow state, and the MOS transistor 29 goes to ON state.例文帳に追加
正の静電気が侵入し入力電圧Vinが所定のしきい値電圧を超えて上昇すると、定電圧回路41が通電状態となり、MOSトランジスタ29がオン状態となる。 - 特許庁
The contact type electrifying device 2 is provided with the electrifying roller 21 as an electrifying member which comes into contact with the photoreceptor 20, and a power supply circuit 26 which applies a direct current constant voltage to the electrifying roller 21.例文帳に追加
接触式帯電装置2は、感光体20に接触する帯電部材としての帯電ローラ21と、帯電ローラ21に直流定電圧を印加する電源回路26とを備えている。 - 特許庁
(step A1) Next, the test energizing is started, and in a first cycle, a thyristor is ignited (step A2) with the above described initial valueϕ(1), and in cycles from and after a second cycle, the ignition angle is determined (step A7) under a constant current control.例文帳に追加
次いで、テスト通電を開始し、1回目のサイクルでは上記初期値φ(1)でサイリスタを点弧し(ステップA2)、2回目以降のサイクルでは定電流制御の下で点弧角を決定する(ステップA7)。 - 特許庁
This device has a time constant circuit which can supply electric power for a prescribed time when the power source is off and is provided with a conduction circuit which supplies a current from the power line of the video amplifying circuit to a drive signal output terminal.例文帳に追加
電源オフ時に所定時間電力を供給可能な時定数回路を有し、映像増幅回路の電源ラインからドライブ信号出力端へと電流を流す導通回路を設けた。 - 特許庁
When the load is short-circuited or under an overload state, a switch element is forced to effect a constant current function and its detection output is fed back to an auxiliary switching element thus stopping the switching of a main switching element.例文帳に追加
負荷の短絡あるいは過負荷時に、スイッチ素子に定電流機能動作をさせるとともに、その検出出力を補助スイッチング素子にフィードバックして主スイッチング素子のスイッチングを停止させる。 - 特許庁
At that point, the input impedance of the FET 130 is extremely high so that time constant of discharge route of the discharge current can be fully extended even if the capacitance of the condenser 120 is decreased.例文帳に追加
ここで、FET130の入力インピーダンスは非常に高いため、上記放電電流の放電経路の時定数は、コンデンサ120の静電容量を小さくしても、十分に長くできる。 - 特許庁
To provide a vehicular light unit suppressing the breakage of a light source, in a structure driving the light source by a constant-current circuit and carrying out light control of the light source by PWM control.例文帳に追加
定電流回路により光源が駆動されると共にPWM制御により光源の調光制御が行われる構成において、光源の破損を抑制できる車両用灯具を提供すること。 - 特許庁
A lighting control device for a semiconductor light source comprises a plurality of constant-current DC-DC converters 11 and 12 that are connected in parallel to each other and are provided between a power supply and an anode of the semiconductor light source.例文帳に追加
半導体光源の点灯制御装置であって、相互に並列接続され、電源と半導体光源のアノードとの間に設けられた複数の定電流DCDCコンバータ11,12を備える。 - 特許庁
To provide a wind rate control method for a blower capable of maintaining at a set wind rate by making motor load torque constant through control of supply voltage on the basis of changes of supply current and rotation speed of a DC motor.例文帳に追加
DCモータの供給電流、回転速度の変化に基づいて供給電圧を制御してモータ負荷トルクを一定にして設定風量に維持できる送風機の風量制御方法とする。 - 特許庁
The three color LED lamps 41 of red light, green light and blue light are connected in series or parallel or both in series and parallel, respectively, and are driven by the constant current power supply 3.例文帳に追加
赤色光、緑色光、青色光の三色のLEDランプ41はそれぞれ直列または並列もしくは直列と並列との両方で接続され、定流電源3によって駆動される。 - 特許庁
If the internal short circuit occurs within the predetermined cell block 10 in a constant voltage charging area, the secondary differential value of the charging current and the secondary differential value of the voltage are compared with the respective defined vales.例文帳に追加
また、定電圧充電領域において所定のセルブロック10に内部ショートが発生した場合、充電電流の2回微分値および電圧の2回微分値が、それぞれ規定値と比較される。 - 特許庁
An output voltage of a source-follower circuit 10 composed of a transistor 8 having the same structure as a reset transistor 2 and a constant current source means 9 is used as a reset train voltage.例文帳に追加
リセットトランジスタ2と同一構造のトランジスタ8と定電流源手段9とからなるソースフォロワ回路10を設けて、ソースフォロワ回路10の出力電圧をリセットドレイン電圧として用いる。 - 特許庁
In the generation circuit 12, a capacitor C1 is charged by a constant current source 17 because a MOS transistor M2 turns off simultaneously with the turning on of a MOS transistor M1 when power is supplied.例文帳に追加
基準電圧発生回路12は、電源の投入時に、MOSトランジスタM1がオンすると同時にMOSトランジスタM2がオフするので、コンデンサC1が定電流源17により充電される。 - 特許庁
In the case that negative static electricity infiltrates it and the input voltage Vin is decreased exceeding the prescribed threshold voltage, a constant-voltage circuit 36 is turned into a current flow state, and the MOS transistor 28 goes to ON state.例文帳に追加
負の静電気が侵入し入力電圧Vinが所定のしきい値電圧を超えて低下すると、定電圧回路36が通電状態となり、MOSトランジスタ28がオン状態となる。 - 特許庁
To solve the problem, where, when a PM motor with a high ratio of continuous rating torque to short-time rating torque is controlled by a current control system with a fixed proportional gain and an integration time constant, controllability and stability is impaired.例文帳に追加
連続定格トルクと短時間定格トルクの比が大きいPMモータを比例ゲインおよび積分時定数を固定の電流制御系で制御すると、制御性および安定性に欠ける。 - 特許庁
Since the three-phase transformer 8 is reduction-excited at a single-phase constant voltage, the exciting rushed current generated at the opening of the operation by closing the three-phase high-voltage disconnector 4 is largely reduced.例文帳に追加
三相変圧器8は、単相定電圧で低減励磁されるので、三相高圧断路器4を閉にして運転を再開したときに発生する励磁突入電流は大幅に低減される。 - 特許庁
In this way, the output impedance of the constant current source portion 12a can be ensured even in the high-frequency region and the deterioration of the common mode rejection ratio CMRR of the differential amplifier circuit 2 can be suppressed.例文帳に追加
これにより、高周波領域でも、定電流源部12aの出力インピーダンスを確保して、差動増幅回路2の同相信号除去比CMRRの低下を抑えることができる。 - 特許庁
The transistor 10 is configured to be a so-called source follower circuit wherein a constant current is supplied to the source of the transistor 10 and the same potential level is applied to the gate and the drain, and the transistor 10 outputs the source potential level as the output voltage.例文帳に追加
トランジスタ10は、ソースに定電流が供給され、ゲートとドレインに同電位が印加され、ソース電位を出力電圧として出力する、いわゆるソースフォロワ回路として構成されている。 - 特許庁
To provide an AC adapter which can save power and control constant current output in a no load state, i.e., no output load, and in a load state to a low-voltage load state.例文帳に追加
ACアダプタにおいて出力負荷のない無負荷時及び負荷時の省電力化と定電流出力制御を出力電圧の低い低電圧負荷まで出力する事を可能とする装置を提案する。 - 特許庁
When an operation signal g*# input to a drive IC 20 through a terminal T6 is switched to an ON operation command, a switching element 22 for constant current is turned on to charge the gate of a switching element S*#.例文帳に追加
ドライブIC20に端子T6を介して入力される操作信号g*#がオン操作指令に切り替わることで、定電流用スイッチング素子22をオン操作して、スイッチング素子S*#のゲートを充電する。 - 特許庁
To provide a display device in which influence of variation in transistors which a pixel has is reduced and which can make a light emitting element emit light with a constant luminance regardless of the change of a current characteristic due to degradation, etc.例文帳に追加
画素が有するトランジスタのバラツキの影響が低減され、発光素子を、劣化等による電流特性の変化によらず一定の輝度で発光させることが可能な表示装置を提供する。 - 特許庁
Thereby, the change rate di/dt of a current between the collector and the emitter can be suppressed low at the time of turning-on, and a period of a mirror range, in which the voltage value of the gate terminal 2 becomes constant, can be shortened.例文帳に追加
これにより、ターンオン時のコレクタ−エミッタ間の電流の電流変化率di/dtが小さく抑えられ、かつ、ゲート端子2の電圧値が一定となるミラー領域の期間を短くできる。 - 特許庁
The control method comprises tracking positions of the top edge and the bottom edge of the material to be heated and controlling a terminal voltage of an induction heating device such that a current of each induction heating coil passing through the material to be heated is constant.例文帳に追加
被加熱材の先端の位置と後端の位置をトラッキングし、被加熱材の通過中の各誘導加熱コイルの電流が一定となるように、誘導加熱装置の端子電圧を制御する。 - 特許庁
To provide an LED drive control unit with a drive control means for driving the LED at constant current, and to provide a compact, safety countermeasure for protecting the circuit and preventing heat generation against an LED short-circuit fault.例文帳に追加
LEDを定電流駆動する駆動制御手段と共に、LEDの短絡故障が発生した際の回路保護及び発熱防止に係わるコンパクトな安全対策手段を実現すること。 - 特許庁
When a cable is connected during power supply, an excess current protection circuit is operated by in-rush currents, and currents to a constant voltage power source part 31 is restricted, and a supply voltage to an LNB11 is deteriorated.例文帳に追加
通電中にケーブルが接続されると、インラッシュ電流により過電流保護回路が動作し、定電圧電源部31の電流が制限されてLNB11への供給電圧が低下する。 - 特許庁
Since the resistances R3, R4 have the same temperature coefficient, a potential difference Vref x (R4/R3), between both ends of the resistance R4, is unaffected by temperature changes, and a constant excess current detection reference value can be obtained.例文帳に追加
抵抗R3、R4の温度係数が等しいので、抵抗R4両端の電位差Vref×(R4/R3)は温度変化の影響を受けず、一定の過電流検出基準値が得られる。 - 特許庁
At this time, the current path of the reference potential 17 becomes short by grounding directly the reference potential 17 to the metal chassis and the reference potential becomes constant and the interference electromagnetic waves to be radiated from the data drivers 2 are suppressed.例文帳に追加
ことで、基準電位17を直接金属シャーシに接地することで基準電位の電流経路が短くなり、基準電位が安定し、データドライバ2より放射される妨害電磁波を抑制できる。 - 特許庁
The motor control circuit 21 is composed of an electricity storage device 33 made of an electric double layer capacitor, a constant current control circuit 32 on the cable 15 side, and a back flow preventive circuit 34 on the motor control circuit 21 side.例文帳に追加
モータ制御回路21は、電気二重層コンデンサからなる蓄電装置33と、ケーブル15側の定電流制御回路32と、モータ制御回路21側の逆流防止回路34とで構成する。 - 特許庁
The inverter circuit 4 controls the output current to a constant value so that, when it is hard for the fluorescent lamp 1 to discharge due to a slow leak, the output voltage increases and the power value increases thereby.例文帳に追加
インバータ回路4は出力電流を一定に制御するため、スローリークによって蛍光灯1が放電しにくくなると出力電圧が上昇し、それにより電力値も増加する。 - 特許庁
A reset unit 25 performs a reset when a terminal voltage Vc of the capacitor C charged with the constant current I becomes lower than the reference voltage Vf, and cancels the reset when the terminal voltage exceeds the reference voltage Vf.例文帳に追加
リセット部25は、一定電流Iで充電されるコンデンサCの端子電圧Vcが参照電圧Vfを下回ればリセットを行い、参照電圧Vfを上回ればリセット解除を行う。 - 特許庁
Based on a motor current Im, a motor voltage Vm, the back electromotive force constant Ke and a motor resistance Rm, the rotation angular velocity of the motor is calculated as an estimated rotation angular velocity ωma.例文帳に追加
そして、モータ電流Imとモータ電圧Vmと逆起電圧定数Keとモータ抵抗Rmとに基づいてモータの回転角速度を推定回転角速度ωmaとして算出する。 - 特許庁
The driver circuit (a1, a2, a3) comprises an inverter circuit (4) for imparting a drive signal to the base terminal of the insulated gate transistor (3), and a constant current circuit (6) having a first transistor (8_1) and a second transistor (8_2).例文帳に追加
ドライバ回路(a1,a2,a3)は、絶縁ゲート型トランジスタ(3)のベース端子に駆動信号を付与するインバータ回路(4)と、第1のトランジスタ(8_1)及び第2のトランジスタ(8_2)を有する定電流回路(6)とを備えている。 - 特許庁
A control section 25 controls the reset transistor 5 and a switching portion 12, to control the input-side potential of an inversion amplifier, constituted of the amplifying transistor 3 and a constant-current load transistor 4.例文帳に追加
制御部25により、リセットトランジスタ5と切り替え部12を制御することによって、増幅トランジスタ3と定電流負荷トランジスタ4で構成された反転増幅器の入力側電位を制御する。 - 特許庁
To inexpensively achieve a function for interrupting a no-load oscillation which interrupts a switching operation when the load is disconnected and an output is abnormally increased in a constant current controlled flyback DC-DC converter circuit.例文帳に追加
定電流制御型フライバックDC−DCコンバータ回路において、負荷断線時の出力異常昇圧時にスイッチングを停止させる無負荷時発振停止機能を低コストで実現する。 - 特許庁
To attain stabilization of power supply by suppressing drop of a power supply voltage to be supplied to an LSI by enlarging a through-rate of a rush current from a DC constant voltage power source just after processing start in the LSI.例文帳に追加
LSIでの処理開始直後における直流定電圧電源からの突入電流のスルーレートを大きくして、LSIに供給される電源電圧の降下を抑え、電源の安定化を図る。 - 特許庁
As the result, since resistance components of the constant-current sources 11, 12 are infinite, common mode noise between the transmitting end block TB and the receiving end block RB is not converted into a normal mode between differential signals.例文帳に追加
この結果、定電流源11,12の抵抗成分が無限大であるので、送端ブロックTBと受端ブロックRBとの間にあるコモンモードノイズは、差動信号間のノーマルモードに変換されない。 - 特許庁
Thus, the control circuit 43 makes the total of the current values of the first and second bias currents I1b and I2a, which are to be supplied to first and second input differential couples 51 and 52, a constant value (=I) at all times.例文帳に追加
このように、制御回路43は、第1及び第2入力差動対51,52に供給する第1及び第2バイアス電流I1b,I2aの電流値の合計を常に一定(=I)とする。 - 特許庁
When the detection signals are inputted to the detection device 210, a control unit 220 controls a constant current device 230 generating an output for lighting on the LED to be deactivated.例文帳に追加
検出装置210が検出信号を入力すると、制御装置220が、LEDを点灯する出力を生成する定電流装置230に対し、動作停止等の制御を実行する。 - 特許庁
In a non-volatile memory 14, a forward voltage VF1 obtained when a constant current I1 is made to flow through a PN junction diode of a PNP transistor 11 is stored in advance in an environment where the temperature is managed.例文帳に追加
不揮発性メモリ14は、温度管理されている環境下で、PNPトランジスタ11のPN接合ダイオードに定電流I1を流したときの順方向電圧VF1を予め記憶している。 - 特許庁
Mechanical contact selection means 14a and 14b are used to select whether to connect the charge amplifier circuit 11a or the constant current circuit 11b between the connection part 13 and an amplification circuit 12.例文帳に追加
接続部13と増幅回路12との間に、チャージアンプ回路11aを接続するか定電流回路11bを接続するかは、機械式接点の選択手段14a,14bを用いて選択する。 - 特許庁
A resistance value r of the internal resistance of a secondary battery 4 being charged is measured, and then the secondary battery 4 is charged at constant current I, and charge is finished when voltage V between terminals of the secondary battery 4 reaches voltage Vf+r×I obtained by adding voltage r×I obtained by multiplying the resistance value r by the constant current I to full charge voltage Vf.例文帳に追加
充電しようとする二次電池4の内部抵抗の抵抗値rを測定し、その後この二次電池4を定電流Iで充電し、この二次電池4の端子間電圧Vがこの二次電池4の満充電電圧Vfにこの内部抵抗の抵抗値rにこの定電流Iを乗算した電圧r・Iを加算した電圧Vf+r・Iとなったときに充電を終了するようにしたものである。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|