| 意味 | 例文 |
constant- currentの部分一致の例文一覧と使い方
該当件数 : 4593件
A control means obtains control characteristics representing a relationship among the motor rotating speed, the energizing current value to the hydraulic pressure regulating valve, and the hydraulic pressure of the wheel cylinder based on the hydraulic pressure of the wheel cylinder when the energizing current value to the hydraulic pressure regulating valve is changed while maintaining a constant motor rotating speed.例文帳に追加
制御手段は、モータの回転数を一定に保ち、液圧調整弁への通電電流値を変化させたときのホイールシリンダの液圧にもとづいて、モータの回転数と、液圧調整弁への通電電流値と、ホイールシリンダの液圧との関係を示す制御特性を取得する。 - 特許庁
An image forming apparatus is equipped with an image carrier and a transfer means which abuts against it, and performs constant-current control over the transfer means with a set current in a paper non-feed state wherein no recording material is present at a transfer position where the both abut against each other and varies conveyance intervals of recording materials according to the voltage at this time.例文帳に追加
像担持体と、これに当接する転写手段とを備え、これら両者が当接する転写部位に記録材が存在しない非通紙時に、設定された電流で転写手段を定電流制御し、このときの電圧に応じて記録材の搬送間隔を変更する。 - 特許庁
Electric currents Iu, Iv of the motor 3 are detected by an electric current detection circuit 14 after at least stand-by time based on a time constant of the motor 3 passes after a control signal of a duty ratio 50% is given to a three-phase electric current circuit 131 from a control part 155.例文帳に追加
制御部153から三相電流制御回路131にdヒューティ比50%の制御信号を与えたてから、少なくともモータ3の時定数に基づく待機時間が経過してから、電流検出回路14によりモータ3の電流Iu、Ivを検出する。 - 特許庁
The apparatus and method are characterized in that constant rotational speed of a stator is maintained during continuous welding, and when an electrode 22 is moving above segment end pairs 52, a high welding current is passed through the electrode 22, and when the electrode 22 is moving above the holding fixtures 80, a low welding current is passed through the electrode 22.例文帳に追加
連続溶接中のステータの回転速度を一定とし、電極22がセグメント端部対52の上方を移動しているときには、電極22に流れる溶接電流を高電流とし、電極22が保持冶具80の上方を移動しているときには、溶接電流を低電流とする。 - 特許庁
The output level setting section 160 has a transistor QP12 for supplying a constant current Ip in accordance with control voltage Vm to the node No from a power source node 101, and a transistor QN12 for making to flow a current In accordance with voltage the node Ns to a ground node 102 from the node No.例文帳に追加
出力レベル設定部160は、制御電圧Vmに応じた一定電流Ipを電源ノード101からノードNoに供給するためのトランジスタQP12と、ノードNsの電圧に応じた電流InをノードNoから接地ノード102に流すためのトランジスタQN12とを有する。 - 特許庁
The ratio of the average value for every period or the maximum value of the motor current or the motor torque generated in the accelerating and decelerating operation period and the constant speed operation period of the motor 17 to the tolerable current or the tolerable torque of the motor concerned is obtained and it is switched and displayed for a specified time.例文帳に追加
前記電動機の加減速運転期間と一定速度運転期間で発生する電動機電流または電動機トルクの前記各期間ごとの平均値または最大値と当該電動機の許容電流または許容トルクとの比率を求め、これを切り換えて所定時間表示する。 - 特許庁
The resistance value R_1 of the first resistor, the resistance value R_2 of the second resistor, the resistance value R_3 of the third resistor, the reference current I_ref output from the constant-current power supply, and the output voltage V_out output from the power conversion unit satisfy the formula (1).例文帳に追加
第1の抵抗素子の抵抗値R_1と、第2の抵抗素子の抵抗値R_2と、第3の抵抗素子の抵抗値R_3と、定電流電源から出力される参照電流I_refと、電力変換部から出力される出力電圧V_outとは、数式(1)を満たす。 - 特許庁
The valve element 2 is displaced from a position where a stroke without supply of electric current is 0 to a non-regulated pressure region before the pressure is regulated, the regulated pressure region where an output oil pressure in proportional to the electric current amount to the electromagnetic solenoid 4 is generated, and a constant pressure region where a maximum output oil pressure in the regulated pressure region is maintained.例文帳に追加
弁体2は、非通電時のストロークが0の位置から、調圧が開始されるまでの非調圧域、電磁ソレノイド4への通電量に比例した出力油圧が生じる調圧域、および調圧域の最大出力油圧が維持される定圧域まで変位する。 - 特許庁
Furthermore, the image forming apparatus is equipped with the image carrier and transfer means which abuts against it, and performs the constant-current control over the transfer means with the set voltage in the paper non-feed state wherein no recording material is present at the transfer position where the both abut against each other and varies conveyance intervals of recording materials according to the current at this time.例文帳に追加
更に、像担持体と、これに当接する転写手段とを備え、これら両者が当接する転写部位に記録材が存在しない非通紙時に、設定された電圧で転写手段を定電圧制御し、このときの電流に応じて記録材の搬送間隔を変更する。 - 特許庁
This laser control unit, which generates a laser driving current I_LD2, is equipped with a pickup 3a that projects a laser beam at an optical disk 6, and driving circuit 2a that transmits control data DATA used for controlling the function of the pickup 3a to the pickup 3a for a limited period in which the driving current I_LD2 is at a constant level.例文帳に追加
レーザの駆動電流I_LD2を生成し、光ディスク6にレーザ光を照射するピックアップ3a、及び駆動電流I_LD2が一定値の期間にのみピックアップ3aの機能制御に用いる制御データDATAをピックアップ3aに転送する駆動制御回路2aを備える。 - 特許庁
The constant voltage circuits 31, 32 are switched so that output voltage V31 from the circuit 31 is supplied to loads 21, 22 when a load current is small and the output voltage of the circuit 32 is supplied to the loads 21, 22 when the load current is large.例文帳に追加
負荷電流が小さいときには、定電圧回路31の出力電圧V31を負荷21、22に供給し、負荷電流が大きいときには、定電圧回路32の出力電圧を負荷21、22に供給するように、定電圧回路31および定電圧回路32を切り換える。 - 特許庁
To precisely determine the secondary time constant value of an induction motor according to a curve for indicating a relation with generation torque to a torque content current command by actually measuring the relation between the generation torque and the torque content current in the induction motor in the slip frequency vector control of the induction motor.例文帳に追加
誘導電動機の滑り周波数形ベクトル制御時に、誘導電動機の発生トルクとトルク分電流の関係を実測し、トルク分電流指令に対する前記発生トルクとの関係を示す曲線から、前記誘導電動機の二次時定数の値を正確に決定する。 - 特許庁
To provide a reasonable charging device that integrates a current controlling circuit for pulse-charging with a constant current as switching control systems including pulse width modulation PWM and pulse frequency modulation PFM, and to provide a battery pack with a charge-controlling function using the device.例文帳に追加
定電流でパルス充電するための電流制御回路を、パルス幅変調PWM又はパルス周波数変調PFM等のスイッチング制御方式として統合した合理的な充電装置とすること、更に、それを用いた充電制御機能付き電池パックを提供することである。 - 特許庁
To identify the motor constant and load torque of a permanent magnet type synchronous motor without using a current detector for detecting a current flowing through a motor for driving a permanent magnet type synchronous motor under test (synchronous motor for test) or a synchronous motor under test.例文帳に追加
試供永久磁石型同期電動機(テスト用の同期電動機)を駆動するための駆動用電動機や、試供同期電動機に流れる電流を検出する電流検出器を用いることなく、永久磁石型同期電動機の電動機定数及び負荷トルクの同定を行う。 - 特許庁
To provide an electron beam irradiation treatment device which can output a stable and constant electron beam over a long period from an electron beam tube by setting up a means for detecting the difference between a tube current and an electric current flowing from an electron beam emission component to an earth.例文帳に追加
管電流と電子線出射部からアースに流れる電流との差を検出する手段を設けることにより、電子線管から長期間にわたり安定した一定の電子線を出力させることのできる電子線照射処理装置を提供することにある。 - 特許庁
To dispense with a waveform observation by an operator in actual use, to have a optimized waveform even when a pulse width is shorter than a thermal time constant of the cathode, and to generate controlled pulse current which is controlled as a prescribed bulb current in the shortest start-up time.例文帳に追加
本発明は、実使用時に操作者の波形観測が不要で、パルス幅がカソードの熱時定数より短い場合であっても最適化された波形を持ち、且つ所定の管電流値に制御されたパルス管電流を最短の立上がり時間で発生させることを目的とする。 - 特許庁
Also, a resistor R_3 for a drain current detection is connected between the drain of the FET 1 and the positive power source 3, and an automatic adjustment is performed so that the drain current of the FET 1 may be constant by controlling the source voltage of the FET 1 by the first transistor Q1.例文帳に追加
また、FET1のドレインと正電源3との間に、ドレイン電流検出用の抵抗R_3が接続され、上記第1トランジスタQ1 によりFET1のソース電圧を制御することで、FET1のドレイン電流が常に一定となるように自動調整を行う。 - 特許庁
A white diode driving voltage set at high voltage near the voltage of a commercial power supply is used to reduce driving current and make a junction FET type constant current element usable, and temperature characteristics of the element and tolerance thereof are improved to achieve miniaturization.例文帳に追加
本発明は白色ダイオード駆動電圧を商用電源と近い高電圧に設定したものを用いて、駆動電流を減らして、ジャンクションFET型定電流素子を使用可能とし、その素子の温度特性と交差を改善しかつ小型化を実現するものである。 - 特許庁
To provide a rush current suppression circuit capable of preventing generation of a voltage drop even when the output capacity of a power circuit at a pre-stage is small by preventing generation of a spike-shaped current at switch-on without preparing for a circuit with a larger time constant than is necessary.例文帳に追加
突入電流抑制回路に関し、必要以上に大きな時定数の回路を用意することなく、かつスイッチオン時のスパイク状の電流を発生させないことにより、前段の電源回路の出力容量が小さい場合にも電圧降下を起こさないようにすること。 - 特許庁
When the electrostatic capacity of the translucent discharge container 1 is reduced and the impedance of the translucent discharge container 1 serving as a current limiting impedance is properly increased, a constant current circuit is obtained, thus an electric discharge is stabilized, and a flicker of the electric discharge rarely occurs.例文帳に追加
0.01<t/(D・ε)<0.05 透光性放電容器の静電容量を小さくして、限流インピーダンスとして作用する透光性放電容器のインピーダンスを適当に大きくすることで、定電流回路にすることができるから、放電が安定し、放電のちらつきが生じにくくなる。 - 特許庁
Specifically, a current probe for sandwiching the spherical conductive material between two counter electrodes so as to contact them and bringing constant current to flow therethrough, and a voltage probe for measuring a potential difference between two points on the surface of the spherical conductive material, are disposed independently, thereby enabling a precise evaluation.例文帳に追加
具体的には、2つの対向電極間に球形導電体を挟み込み接触させ定電流を流すための電流プローブ、および球形導電体表面上の2点間の電位差を測定するための電圧プローブを独立に設置し、正確な評価を可能にした。 - 特許庁
The control circuit 4 comprises a connecting terminal 13 to which a capacity C is connected, a constant current source 6 that feeds a charge current to the capacitor C, a buffer 17 that inputs a charge voltage of the capacity C, and voltage dividing resistors R that divide output voltages of the buffer 17.例文帳に追加
制御回路4は、容量Cが接続される接続端子13と、容量Cに充電電流を供給するための定電流源6と、容量Cの充電電圧を入力するバッファ17と、バッファ17の出力電圧を分圧する分圧抵抗Rとを備える。 - 特許庁
When performing the constant power control of a discharge lamp 14, a control circuit 18 obtains a current value of the discharge lamp 14 from a current detection circuit 16, reads the correction factor stored in a storage device, multiplies the value by a detected value, and obtains an output power using a value after the multiplication.例文帳に追加
制御回路18は、放電灯14の定電力制御を行う際に、放電灯14の電流値を電流検出回路16より取得し、記憶装置に格納した補正係数を読み込み、その値を検出値に乗算して、乗算後の値を用いて出力電力を求める。 - 特許庁
An image signal processing part 13 is configured to, when changing the current value of the LED, adjust the image signal in accordance with the current value of the LED so that the display hue of the liquid crystal panel 18 in accordance with the input image signal of a predetermined gradation may be always constant.例文帳に追加
そして、映像信号処理部13は、LEDの電流値を変更する場合に、所定階調の入力映像信号に応じた液晶パネル18の表示の色味が常に一定になるように、LEDの電流値に応じて映像信号を調整する。 - 特許庁
To drive a plurality of loads being requested with different characteristics by varying a load current for driving a constant current load within a specified range using an output circuit such as a DC-DC conversion power supply circuit, and by sustaining the output voltage at a specified level or above for other loads.例文帳に追加
直流−直流変換型電源回路等の出力回路を用いて、定電流負荷を駆動する負荷電流を所定範囲に変化させるとともに、他の負荷のために出力電圧を所定値以上に保つようにして、要求される特性の異なる複数の負荷を駆動すること。 - 特許庁
The current adjustment circuit compares an external supply voltage with a first reference voltage, and if the external supply voltage is equal to or higher than the first reference voltage, reduces a current value of a constant voltage signal generated by stepping down the external supply voltage, in accordance with the external supply voltage.例文帳に追加
電流調整回路は、外部電源電圧と第1の基準電圧を比較し、外部電源電圧が第1の基準電圧以上のとき、外部電源電圧を降圧することで生成された定電圧信号の電流値を、外部電源電圧に応じて低減する。 - 特許庁
The secondary battery pack each has: a secondary battery; charge switch means to turn on and off a charge path to an secondary battery; discharge switch means to turn on and off a discharge path from the secondary battery; and current-limiting means to make the secondary battery discharge while limiting a current to a constant value or less.例文帳に追加
二次電池パックは、二次電池と、二次電池への充電経路をオンオフする充電スイッチ手段と、二次電池からの放電経路をオンオフする放電スイッチ手段と、二次電池を、電流を一定値以下に制限しつつ放電させる電流制限手段とをそれぞれに有する。 - 特許庁
An alternating constant current is made to flow between current impressing electrodes 21, 22, voltages generated between voltage measuring electrodes 23, 24 are detected to be converted into serial digital values by an MPU 30, and a measured result of the conductivity is output in a condition insulated electrically from its outside from a photocoupler 32.例文帳に追加
電流印加電極21,22間に交流化した定電流を流し、電圧測定電極23,24間に発生する電圧を検出してMPU30がシリアルのデジタル値に変換し、フォトカプラ32から電気的に外部と絶縁した状態で、導電率の測定結果を出力する。 - 特許庁
Between a rectification part 1 to convert an input AC voltage into a DC voltage and a constant current part 4 having an FET to control the electric current flowing to the fluorescent lamp, a step-up/step-down voltage chopper part 3 having two pieces of switching elements Q1, Q2 PWM-driven by a control part 8 is provided.例文帳に追加
入力交流電圧を直流化する整流部1と、蛍光灯に流す電流を制御するためのFETを有する定電流部4との間に、制御部8によりPWM駆動される2個のスイッチング素子Q1、Q2を有する昇降圧チョッパ部3を設ける。 - 特許庁
The control means 103 is constructed in such a way that an oscillation state of the DBR laser 101 is controlled by injecting a driving current whose current value and injection time are adjusted so as to make the sum of the heat quantity produced within a period be kept constant per period to a plurality of active regions 101b, 101c respectively.例文帳に追加
制御手段103は、一周期内に発生する熱量の和が周期ごとに一定となる様に電流値及び注入時間の調整された駆動電流を複数の活性領域101b、101cに夫々注入することでDBRレーザ101の発振状態を制御できる様に構成される。 - 特許庁
When the temperature data TA, TB, and TC are "110", the transistor 16 is in the off state, because the temperature data TB is "1", so that the supply of the current to the resistors 11 and 12 is shut off; and the comparator 10 forcedly outputs "1", in which the constant current source is shut off.例文帳に追加
温度データTA,TB,TCが“110”の場合、温度データTBが“1”であるためにトランジスタ16がオフ状態となって抵抗器11、12への電流供給が遮断され、比較器10は定電流源が遮断されて強制的に“1”を出力する。 - 特許庁
The peak current limit threshold or the operating frequency are trimmed during manufacture specifically to maintain the product of I_p^m×f^n divided by the control threshold current substantially constant from one power supply controller to another where m is substantially equal to 2 and n is substantially equal to 1.例文帳に追加
ピーク電流制限閾値または動作周波数は、具体的には、電源制御器ごとに、I_p^m・f^nの積を制御閾値電流で割った値を実質的に一定に維持するように調整され、ここでmが実質的に2に等しく、かつnが実質的に1に等しい。 - 特許庁
The battery ECU determines whether an SOC estimation routine for this time is performed in a case where the current of the battery changes after continuation of a constant current state (S110-S160), and in such a case, sets a polarization value correction rate kf so as to satisfy kf>1.0 (S180).例文帳に追加
電池ECUは、今回のSOC推定ルーチンが一定電流状態の継続後にバッテリ電流が変化したケースで実行されているかどうかを判定し(S110〜S160)、このようなケースでは、分極値補正率kfをkf>1.0に設定する(S180)。 - 特許庁
On the occasion when either a line L1 or L2 on the RTD sensor 2 side is disconnected and a capacitor 42 of a filter circuit 4 is charged by a current from the constant current source 3, a switch 5 connected with a detecting part 6 in parallel is closed and input voltage to an amplifying part 61 is limited to a prescribed threshold.例文帳に追加
RTDセンサ2側のラインL1,L2のいずれかが断線して定電流源3からの電流によりフィルタ回路4のコンデンサ42が充電された際、検出部6と並列に接続されたスイッチ5を閉として、増幅部61への入力電圧を所定の閾値に制限する。 - 特許庁
When a contact M and a contact J are set on and other contacts are set off, the current from the constant-current source 31 will flow through the contact M, the needle 13, the circuit pattern 51, the needle 11, and the contact J, and the polarity of the needle 13 is positive, while the polarity of the needle 11 is set negative.例文帳に追加
接点Mおよび接点Jをオンとし、他の接点をオフとすれば、定電流源31からの電流が接点M、ニードル13、回路パターン51、ニードル11、接点Jと流れ、ニードル13の極性をプラス、ニードル11の極性をマイナスとすることができる。 - 特許庁
In the case the charging circuit of the electric double-layer capacitor is in a constant-current charging mode of a charging current I, the capacitance measurement of the electric double-layer capacitor is started as the electric double-layer capacitor finished charging and the voltage of the electric double-layer capacitor is reduced equal to or less than a fixed voltage.例文帳に追加
電気二重層コンデンサの充電回路が充電電流Iの定電流充電モードの場合、電気二重層コンデンサの放電が終了して電気二重層コンデンサの電圧が一定電圧以下に下がったとき電気二重層コンデンサの容量測定を開始する。 - 特許庁
When an LED 1 for irradiation is driven for blinking or driven for lighting at a constant current pulse, an emitter current flowing in a pair of emitter coupling transistor circuits 5a, 5b is controlled at a voltage V11 applied from a DC control source 6a to a base terminal of a transistor Q5 with a high impedance.例文帳に追加
照明用LED1を定電流パルスで点滅駆動又は点灯駆動させるにあたり、一対のエミッタ結合トランジスタ回路5a、5bに流れるエミッタ電流を、DC制御源6aから高インピーダンスのトランジスタQ5のベース端子に印加される電圧V11で制御する。 - 特許庁
In order to sustain a constant rotational speed at all times, current PWM control for varying power thrown to the motor depending on variation in load is employed, and the generated pressure and discharge amount of the pump are managed by determining the phase of the roll, based on the current PWM value.例文帳に追加
回転数を常に一定に保つため、負荷変動に応じてモータへの投入電力を変動させる電流PWM制御を採用するとともに、その電流PWM値に基いてコロの位相を確定し、ポンプの発生圧力および排出量を管理する。 - 特許庁
Since the gate of the P channel MOS transistor P1 to supply a constant current to be a reference can be controlled independently of the drain, there is no limit for the drain current of the P channel MOS transistor P1 so that the voltages at both the ends of the resistor R18 are not limited.例文帳に追加
基準となる定電流が供給されるPチヤネルMOSトランジスタP1のゲートをドレインと独立して制御可能であるため、PチヤネルMOSトランジスタP1のドレイン電流に制限がなくなり、よって抵抗R18の両端電圧は制限されることがない。 - 特許庁
A sensing signal from the water temperature sensor 6a is input to a current control circuit 8 of the electric deionization device, and controls applied voltage and/or energizing current to the electric deionization device 5 so that electric conductivity or specific resistance of the treated water from the electric deionization device 5 becomes constant.例文帳に追加
水温センサ6aの検知信号は、電気脱イオン装置通電制御回路8に入力され、電気脱イオン装置5からの処理水の導電率又は比抵抗が一定となるように、電気脱イオン装置5への印加電圧及び/又は通電電流を制御する。 - 特許庁
The current is a linear combination of the current needed to generate the desired magnetic field in an area of concern and an error item represented by a mathematical model of a series of exponential functions experimentally determined during system calibration and having a predetermined amplitude and time constant.例文帳に追加
この電流は、関心のある領域に所望の磁界を発生するのに必要な電流と、システムの較正の際に実験的に決定されて所定の振幅及び時定数を持つ一連の指数関数という数学モデルによって表される誤差項との線形の組合せである。 - 特許庁
For example, when the optical output from the semiconductor laser device 1 decreases by secular changes, and an optical absorption current detector 6 detects a decrease in the optical absorption current, the bias adjusting circuit 7 increases an extinction ratio and decreases the bias so that the optical output is kept constant.例文帳に追加
例えば、経年変化によって半導体レーザ装置1からの光出力が低下した場合、光吸収電流検出回路6が光吸収電流の低下を検出すると、バイアス調整回路7は消光比を大きくして光出力が一定になるように、バイアスを小さくする。 - 特許庁
A current supplied to make the luminance of a light emission part 4 constant is calculated from the estimated ambient temperature and the luminance of the light emission part 4 is controlled through a data-side driving circuit 8 which supplies a current to a positive electrode line 2 connected to the light emission par t 4.例文帳に追加
この推定された周囲温度をもとに、発光部4の輝度が一定となるための供給電流を算出し、発光部4に接続された陽極線2に電流供給するデータ側駆動回路8を介して発光部4の輝度を制御することとした。 - 特許庁
The input LED 13a of the photocoupler 13 is connected so as to emit light, based on the current flowing into a constant current circuit 14, allowing the output photo transistor 13b of the photo-coupler 13 to be turned on/off, corresponding to the light emitted from the input LED 13a.例文帳に追加
フォトカプラ13の入力発光ダイオード13aは、定電流回路14に流れる電流に基づいて発光するように接続されており、フォトカプラ13の出力フォトトランジスタ13bは、入力発光ダイオード13aから放射される光に応答してオンオフする。 - 特許庁
If the terminal voltage VBAT reaches the charging target value of the battery cell 17, the counter circuit 13 measures an elapsed time afterward, and when elapsed time accords with the measured result, constant-current charge by a fixed current control circuit 9 to a switching circuit 11 is ended.例文帳に追加
端子電圧VBATが電池セル17の充電目標値に達すると、カウンタ回路13は以後の経過時間を計測して、経過時間が保持した計測結果に一致すると切替回路11に対し定電流制御回路9による定電流充電を終了させる。 - 特許庁
When the collector current of the transistor Q14 flows, the base current of a transistor Q12 is interrupted, and an external control terminal R becomes high impedance, and DC voltage of approximately 1.4V being remote off voltage is outputted between the Vout terminal and the GND terminal of a constant-voltage switching power circuit.例文帳に追加
トランジスタQ14のコレクタ電流が流れると、トランジスタQ12のベース電流が遮断され、外部制御端子Rがハイインピーダンスになって、定電圧スイッチング電源回路のVout端子とGND端子との間にリモートオフ電圧である約1.4Vの直流電圧が出力される。 - 特許庁
To apply effective cathodic corrosion prevention by a constant potential control type external power source cathodic corrosion prevention system to an object for corrosion prevention in a local region where electric resistance to DC stray current is lower than that of the circumference thereof, and also the value of DC stray current is made high under prescribed conditions.例文帳に追加
直流迷走電流に対する電気抵抗が周囲に比べて低く且つ所定の条件下で直流迷走電流の値が大きくなる局所的な領域の防食対象に対して、定電位制御型外部電源カソード防食システムによる効果的なカソード防食を行う。 - 特許庁
A power supply circuit is controlled such that a high level current is output during a first arc period Ta1 that is an initial period of an arc period continuing after a short-circuit period, and an arc current corresponding to a welding voltage subjected to constant voltage control is output during a second arc period Ta2 that is the latter period of the arc period.例文帳に追加
短絡期間の後に続くアーク期間の初期の第1アーク期間Ta1にハイレベル電流が出力され、アーク期間の後期の第2アーク期間Ta2に定電圧制御された溶接電圧に対応したアーク電流が出力されるように、電源回路が制御される。 - 特許庁
If the voltage data before the start of charging is assumed as D0, the rate of the current residual amount of the battery is presumed to be approx. 50% regardless of the battery deteriorated condition, and if the battery is deteriorated, the charging time till the terminal voltage attaining the reference value with charging by the specified constant current becomes below tref.例文帳に追加
充電開始前の電圧データをD0 とすると、バッテリの劣化状態にかかわらず、当該バッテリの現在の残量割合は約5割と推測され、バッテリが劣化していれば、所定の定電流による充電で端子電圧が基準値に達するまでの充電時間はtref 以下となる。 - 特許庁
In the circuit, a CMOS transistor is arranged for each electrode of a battery and thereby, the direction of the current flowing in the equipment is made constant by the selection effect of the CMOS transistor, in whichever direction the current flows according to the direction of the battery, and this circuit is built in the equipment.例文帳に追加
CMOSトランジスタを電池の電極ごとに配置して、電池の方向によって電流がどちらの方向に流れてもCMOSトランジスタの選択効果により機器に流れる電流の向きは一定になるようにした回路にし、この回路を機器に内蔵する。 - 特許庁
| 意味 | 例文 |
| Copyright © Japan Patent office. All Rights Reserved. |
|
ログイン |
Weblio会員(無料)になると
|
|
ログイン |
Weblio会員(無料)になると
|